Ganz ZN8 Series User manual

GANZ ZN8 Panorama Fisheye Network Camera

User Manual

Issue

V1.0

Date

2016-02-22

Panorama Fisheye Network Camera

User Manual

Precautions

Issue V1.0 (2016-02-22)

i

Precautions

Fully understand this document before using this device, and strictly observe rules in

this document when using this device. If you install this device in public places,

provide the tip "You have entered the area of electronic surveillance" in an eye-

catching place. Failure to correctly use electrical products may cause fire and severe

injuries. To prevent accidents, carefully read the following context:

Symbols

This document may contain the following symbols whose meanings are described

accordingly.

Symbol

Description

It alerts you to fatal dangers which, if not avoided, may

cause deaths or severe injuries.

It alerts you to moderate dangers which, if not avoided,

may cause minor or moderate injuries.

It alerts you to risks. Neglect of these risks may cause

device damage, data loss, device performance

deterioration, or unpredictable results.

It provides a tip that may help you resolve problems or

save time.

It provides additional information.

To prevent electric shocks or other dangers, keep power plugs dry and clean.

 Strictly observe installation requirements when installing the device. The

manufacturer shall not be held responsible for device damage caused by users' non-

conformance to these requirements.

Precautions

Panorama Fisheye Network Camera

User Manual

ii

Issue V1.0 (2016-02-22)

 Strictly conform to local electrical safety standards and use power adapters that are

marked with the LPS standard when installing and using this device. Otherwise,

this device may be damaged.

 Use accessories delivered with this device. The voltage must meet input voltage

requirements for this device.

 If this device is installed in places with unsteady voltage, ground this device to

discharge high energy such as electrical surges in order to prevent the power supply

from burning out.

 When this device is in use, ensure that no water or any liquid flows into the device.

If water or liquid unexpectedly flows into the device, immediately power off the

device and disconnect all cables (such as power cables and network cables) from

this device.

 Do not focus strong light (such as lighted bulbs or sunlight) on this device.

Otherwise, the service life of the image sensor may be shortened.

 If this device is installed in places where thunder and lightning frequently occur,

ground the device nearby to discharge high energy such as thunder strikes in order

to prevent device damage.

 Avoid heavy loads, intensive shakes, and soaking to prevent damages during

transportation and storage. The warranty does not cover any device damage that is

caused during secondary packaging and transportation after the original packaging

is taken apart.

 Protect this device from fall-down and intensive strikes, keep the device away from

magnetic field interference, and do not install the device in places with shaking

surfaces or under shocks.

 Clean the device with a soft dry cloth. For stubborn dirt, dip the cloth into slight

neutral cleanser, gently wipe the dirt with the cloth, and then dry the device.

 Do not jam the ventilation opening. Follow the installation instructions provided in

this document when installing the device.

 Keep the device away from heat sources such as radiators, electric heaters, or other

heat equipment.

 Keep the device away from moist, dusty, extremely hot or cold places, or places

with strong electric radiation.

 If the device is installed outdoors, take insect- and moisture-proof measures to

avoid circuit board corrosion that can affect monitoring.

 Remove the power plug if the device is idle for a long time.

 Before unpacking, check whether the fragile sticker is damaged. If the fragile

sticker is damaged, contact customer services or sales personnel. The manufacturer

shall not be held responsible for any artificial damage of the fragile sticker.

Panorama Fisheye Network Camera

User Manual

Precautions

Issue V1.0 (2016-02-22)

iii

Special Announcement

All complete products sold by the manufacturer are delivered along with nameplates,

operation instructions, and accessories after strict inspection. The manufacturer shall

not be held responsible for counterfeit products.

This manual may contain misprints, technology information that is not accurate enough,

or product function and operation description that is slightly inconsistent with the

actual product. The manufacturer will update this manual according to product function

enhancement or changes and regularly update the software and hardware described in

this manual. Update information will be added to new versions of this manual without

prior notice.

This manual is only for reference and does not ensure that the information is totally

consistent with the actual product. For consistency, see the actual product.

Contents

Panorama Fisheye Network Camera

User Manual

iv

Issue V1.0 (2016-02-22)

Contents

Precautions .................................................................................................................... i

1 Overview ................................................................................................................... 1

1.1 Front Panel ..................................................................................................................... 1

1.2 Multi-head Cable ............................................................................................................ 2

1.3 Features .......................................................................................................................... 3

2 Device Dimensions ................................................................................................. 5

3 Device Installation ................................................................................................... 6

3.1 Installation Mode............................................................................................................ 6

3.2 Installation Procedure ..................................................................................................... 6

3.3 Optional Accessories ...................................................................................................... 9

4 Quick Configuration ............................................................................................. 11

4.1 Login and Logout .......................................................................................................... 11

4.2 Main page layout .......................................................................................................... 12

4.3 Browsing Video ............................................................................................................ 13

4.3.2 Download the right control in the Internet Explorer......................................... 15

4.3.3 In the Google, Firefox, or Safari browsers watch Live video ........................... 16

4.4 Setting Local Network Parameters ............................................................................... 16

4.5 Fisheye Configuration .................................................................................................. 19

5 Technical Specifications ....................................................................................... 21

A Hazardous Substance Declaration ..................................................................... 25

Panorama Fisheye Network Camera

User Manual

1 Overview

Issue V1.0 (2016-02-22)

1

1 Overview

1.1 Front Panel

Błąd! Nie można odnaleźć źródła odwołania. shows the front panel of the Fisheye

Network Camera.

Figure 1-1 Front panel

Table 1-1 describes the components on the front panel.

Table 1-1 Components on the front panel

No.

Component

Description

1

NIC indicator

Green when the network runs properly.

2

Power supply

indicator

The indicator on when connect to the power

supply.

3

SD card

indicator

Indicate the card status, the status is described as

follows:

 Off: No card is inserted.

 On: An SD card is inserted.

1 Overview

Panorama Fisheye Network Camera

User Manual

2

Issue V1.0 (2016-02-22)

No.

Component

Description

4

Reset button

Restores the camera to the factory settings by

pressing and holding this button for more than

five seconds.

5

SD card slot

Install an SD card.

NOTE

 Before install an SD card, verify the card not in

write protection state.

 Before remove the SD card. Verify the card not in

write protection state. Otherwise, the data may be

lost ,or the SD card may be damaged.

1.2 Multi-head Cable

Figure 1-2 shows the multi-head cable used by the Fisheye Network Camera. Table 1-2

describes the multi-head cable.

Figure 1-2 Multi-head cable

Panorama Fisheye Network Camera

User Manual

1 Overview

Issue V1.0 (2016-02-22)

3

Table 1-2 Multi-head cable description

NO.

Color

Port

Description

1

Gray core

Alarm output

terminal A

(normal open)

Alarm output

Purple core

Alarm output

terminal B

(normal open)

yellow core

Alarm input

positive

terminal

Alarm input terminal

Orange core

Alarm input

ground

terminal

2

N/A

Audio input

port

(line in)

Receives analog audio signals from

devices such as a sound pickup device.

3

Audio output

port

Connects to an external audio device

such as a speaker.

4

Power supply

port

Connects to a 12V (-15%~+10%) direct

current (DC) power supply or 24V (-

15%~+10%) alternating current (AC)

power supply.

NOTE

When the power is PoE, you cannot

access DC12V and AC24V interface at the

same time.

5

Network

access port

Connects to a standard Ethernet cable.

1.3 Features

Network Features

 Support complete TCP/IP protocol suite.

 Support video, audio, and alarm data.

 Provides a built-in web browser and supports access using Internet explorer..

 Supports network data transmission and remote access.

1 Overview

Panorama Fisheye Network Camera

User Manual

4

Issue V1.0 (2016-02-22)

 Support Point-to-Point protocol over Ethernet (PPPoE), Dynamic Host

configuration protocol (DHCP), and Dynamic Domain Name System (DDNS)

protocols.

 Supports Power over Ethernet (PoE) that complies with the IEEE802.3af standard.

The IP camera can connect to a switch or router supporting the PoE function to

implement PoE.

 Support remote upgrade and maintenance.

Image Processing Features

 Support multiple steams. Single-stream model or dual-stream mode can be selected

based on the site requirement. Encoding parameters for the main stream and sub

stream be configured separately.

 Support dynamic stream parameters based on different image quality requirement.

 Support independent hardware compression and constant bit rate (CBR) and

variable bit rate (VBR) Videos can be compressed using the Motion Joint

Photographic Experts Group (MJPEG) or H.264 standard. The frame rate and

image quality can be configured

I/O Features

 Support bidirectional intercom and unidirectional broadcast.

 Provides a 10/100 Mbit/s self-adaptive Ethernet port.

Other Features

 Support the heartbeat function that allows the management host to learn the

running status of the IP camera in real time.

 Support level-based user rights management.

Panorama Fisheye Network Camera

User Manual

2 Device Dimensions

Issue V1.0 (2016-02-22)

5

2 Device Dimensions

Figure 2-1 shows the fisheye camera dimensions.

Figure 2-1 Dimensions (unit: mm)

3 Device Installation

Panorama Fisheye Network Camera

User Manual

6

Issue V1.0 (2016-02-22)

3 Device Installation

3.1 Installation Mode

You can install the fisheye network camera in the ceiling mount and wall mount mode

depending on the actual installation scenario. This section describes how to install the

camera in the ceiling mount mode.

3.2 Installation Procedure

Step 1 Remove the installation bracket

1. Take out the camera, keep the dome cover down, rotate and remove the decoration,

as shown in Figure 3-1.

Figure 3-1 Remove the decoration

2. Use the L-wrench in the accessory package to unscrew the four star screws, remove

the installation bracket. See Figure 3-2.

Panorama Fisheye Network Camera

User Manual

3 Device Installation

Issue V1.0 (2016-02-22)

7

Figure 3-2 Remove the installation bracket

Step 2 Fix the installation bracket

1. Fetch the positioning labeling from the accessory package, remove the release

paper from the positioning labeling, and stick the labeling to the place where the

camera is to be installed, as shown in Figure 3-3.

3 Device Installation

Panorama Fisheye Network Camera

User Manual

8

Issue V1.0 (2016-02-22)

Figure 3-3 Fix the installation bracket

2. Use a drill with a diameter of 5.5mm to drill four round holes with a depth of

40mm. Use a hammer or any other rigid object to nail the four white plastic buttons

into the round holes. Ensure that the wall surface is level and the plastic buttons

align with the wall surface.

3. Drill a thread hole with a diameter of 30mm in the center of the positioning

labeling to route the multi-head cable.

If you use the aside routing method, please use the square type junction box or circular

junction box, as shown in Table 3-1

4. Aim the four through-holes of the installation bracket at the white plastic buttons,

and use four black self-tapping screws with a length of 30mm to fix the installation

bracket.

Step 3 Install the camera

1. Connect the standard Ethernet cable and power supply, ensure that the NIC

indicator and power supply indicator on.

2. Aim the four holes of the camera at the four screw bolts, use the L-wrench to fasten

the four star screws. See Figure 3-4.

Panorama Fisheye Network Camera

User Manual

3 Device Installation

Issue V1.0 (2016-02-22)

9

Figure 3-4 Install the camera

3. Aim the two buckles of the decoration at the classis gap and push in, then rotate the

decoration to no turning, as shown in Figure 3-4.

The wall mount installation mode is similar to the ceiling mount installation mode,

Therefore, wall mount installation details are outside the scope of this section.

3.3 Optional Accessories

The bracket installation may be used in actual installation, the specific optional

accessories, see Table 3-1.

Table 3-1 Accessories

Element

Image

Description

CAP

Match with 3/4”-14NPS thread

3 Device Installation

Panorama Fisheye Network Camera

User Manual

10

Issue V1.0 (2016-02-22)

Element

Image

Description

Wall mount

Pendant

mount

Square type

junction box

Circular

junction box

Pole mount

Corner mount

Panorama Fisheye Network Camera

User Manual

4 Quick Configuration

Issue V1.0 (2016-02-22)

11

4 Quick Configuration

4.1 Login and Logout

You must use Internet Explorer 6 or a later version to access the web management

system; otherwise, some functions may be unavailable.

Login system

Step 1 Open the Internet Explorer, enter the IP address of IP camera (default value:

192.168.1.168) in the address box, and press Enter.

The login page is displayed, as shown in Figure 4-1.

Figure 4-1 Login page

Step 2 Input the User and password.

 The default name is ADMIN. The default password is 1234. Change the password when

you log in the system for first time to ensure system security.

 You can change the system display language on the login page.

Step 3 Click Login.

The main page is displayed.

4 Quick Configuration

Panorama Fisheye Network Camera

User Manual

12

Issue V1.0 (2016-02-22)

logout

To logout of system, click Sign out in the upper right corner of the main page, the login

page is display after you log out of the system.

4.2 Main page layout

On the main page, you can view Live video, playback and configuration, change the

password, and log out of the system. Figure 4-2 is shown the main page layout. Table

4-1 describes the elements on the main page.

Figure 4-2 Main page layout

Table 4-1 Elements on the main page

N

O.

Element

Description

1

Live video area

Live videos are played in this area. You can also set sensor

parameters.

2

Playback

You can query the playback videos in this area.

NOTE

Only when the SD card has videos that you can query the

playback videos.

3

Configuration

You can choose a menu to set device parameters,

including the device information, audio and video streams,

alarm setting, and privacy mask function.

4

Alarm icon

When the device generates an alarm, the alarm icon

is displayed. You can click to view the alarm

information.

NOTE

Panorama Fisheye Network Camera

User Manual

4 Quick Configuration

Issue V1.0 (2016-02-22)

13

N

O.

Element

Description

When the device accepts an alarm signal, the alarm icon

will display within 10s in the web management system.

5

Fault icon

When the device encounters an exception, the fault icon

is displayed.

You can click to view the fault information.

6

Change

password

You can click to change the password.

7

Sign Out

You can click to return to the login page.

4.3 Browsing Video

User can browse the Live video in the web management system.

Preparation

To ensure the Live video can be play properly, you must perform the following

operation when you log in to the web for the first time:

1. Open the Internet Explorer. Choose Tools > Internet options > Security >

Trusted sites > Sites.

In the display dialog box, click Add, as shown in Figure 4-3.

4 Quick Configuration

Panorama Fisheye Network Camera

User Manual

14

Issue V1.0 (2016-02-22)

Figure 4-3 Adding the a trusted site

2. In the Internet Explorer, choose Tool > Internet Options > Security > Customer

level, and set Download unsigned ActiveX control and initialize and script ActiveX

controls not marked as safe for scripting under ActiveX controls and plug-ins to

Enable, as shown in Figure 4-4.

Figure 4-4 Configuring ActiveX control and plug-ins

3. Download and install the player control as prompted.

Page is loading ...

Ganz ZN8 Series User manual

Ganz ZN8 Series User manual

Other documents