Legrand LMBC-600 User manual

Brand: Legrand

Model: LMBC-600

Category: Bridges & repeaters

Type: User manual

This manual is also suitable for

DLM Wireless Network Bridge Module Quick Start

Legrand LMBC-600 is a wireless network bridge module that provides a network connection for a group of Wattstopper Digital Lighting Management (DLM) Local Network room level devices. It connects the DLM local network to either the DLM Segment Manager or a third party system using the BACnet protocol, exposing the status and parameters of all connected devices to the broader network. The LMBC-600 supports up to 64 load addresses and 47 communicating devices, including up to 4 LMRC-10x series and/or LMPL-101 controllers. It has a range of up to 100 ft.

Wattstopper

DLM Wireless Network Bridge Module

Quick Start Guide • Guide de démarrage rapide • Guía de inicio rápido

No: 25224 – 08/17 rev. 3

Catalog Number • Numéro de Catalogue • Número de Catálogo: LMBC-600

Country of Origin: Made in China • Pays d’origine: Fabriqué en Chine • País de origen: Hecho en China

LMBC-600-U is BAA and TAA compliant (Product produced in the U.S.)

SPECIFICATIONS

Voltage ...........................................................................................24VDC

Current Consumption .......................................................................20mA

Power Supply ..............................................Wattstopper Room Controller

Connection to the DLM Local Network .................................2 RJ-45 ports

Segment Network ......................................... BACnet IPv6 Mesh Network

DLM Local Network characteristics when using LMRC-11x/2xx room

controllers:

Low voltage power provided over Cat 5e cable (LMRJ); max current

800mA. Supports up to 64 load addresses, 47 communicating

devices including up to 4 LMRC-10x series and/or LMPL-101

controllers. Free topology up to 1,000’ max.

Environment ..............................................................For Indoor Use Only

Operating Temperature ............................. 32° to 158°F (0° to 70°C)

Storage Temperature ...............................23° to 176°F (-5° to 80°C)

Relative Humidity ................................... 5 to 95% (non condensing)

Indoor Use Only

Security

AES 128bit Key Encryption

Preshared key (non-commissioned state)

Key rotation after commissioning

Wireless

IEEE 802.15.4 , 2.4gHZ

Channels .................................11-26, default is 15 non-overlapping

.................................................................. 15, 20, 26 recommended

Wireless Standard .............................................................6LoWPAN

CoAP—constrained application protocol

Internal Antennas with Diversity

Bandwidth .................................................................. up to 156kbps

Range .................................................................. up to 100 ft. radius

Supported Standards ..........................Bacnet, IPV6, Contiki, RPL,SMRF

RoHS compliant

UL2043 Plenum rated

This unit is pre-set for Plug n’ Go™ operation, adjustment

is optional.

For full operational details, adjustment and more features of the product,

see the DLM System Installation Guide provided with Wattstopper room

controllers, and also available at www.legrand.us/wattstopper.

Installation shall be in accordance with all applicable regulations,

local and NEC codes. Wire connections shall be rated suitable for the

wire size (lead and building wiring) employed.

For Class 2 DLM devices and device wiring: To be connected to a Class

2 power source only. Do not reclassify and install as Class 1, or Power

and Lighting Wiring.

DESCRIPTION AND OPERATION

The LMBC-600 Network Bridge module provides a network

connection for a group of Wattstopper Digital Lighting

Management (DLM) Local Network room level devices.

The DLM local network must include at least one room/load

controller. Connecting the LMBC-600 to the DLM local network

then to either the DLM Segment Manager or a third party

system using the BACnet protocol exposes the status and

parameters of all connected devices to the broader network.

MOUNTING AND INSTALLATION

Determine a suitable location for the LMBC-600. This will usually be in the ceiling closely located to the DLM local network devices to

be networked either directly in the room/space or just outside in a hallway for easier access. Classrooms and patient rooms are ideal for

hallway mounting of the bridge.

The LMBC-600 is UL2043 Plenum rated and comes with an DIN rail mounting plate for flexibility.

Warning: The LMBC-600 is a wireless device. Avoid mounting next to motors, large metal obstructions, or within 12” of another wireless

emitting device.

Attach DIN rail clip

Option 1: Attach to DIN rail

Option 2: Mount to wall

WIRING TO THE DLM LOCAL NETWORK

The DLM local network uses free topology low voltage wiring. The LMBC-600 can connect anywhere on the DLM local network using

LMRJ cables.

Use a Wattstopper LMRJ series cable or a Cat5e patch cable to connect the LMBC-600 to one of the RJ-45 jacks on any of the DLM

local network devices. When connected to a powered DLM local network the red Transmit LED blinks rapidly. The red Config LED blinks

at the same rate as the other DLM local network devices.

WARNING: Connect the LMBC-600 RJ-45 jack only to DLM lighting control devices. Do not connect Ethernet to the LMBC-600 RJ-45 jack.

CAUTION: TO CONNECT A

COMPUTER TO THE DLM LOCAL

NETWORK USE THE LMCI-100.

NEVER CONNECT THE DLM LOCAL

NETWORK TO AN ETHERNET PORT

– IT MAY DAMAGE COMPUTERS AND

OTHER CONNECTED EQUIPMENT.

Segment Manager

or BAS

LMRJ Cables

Occupancy

Sensor

Switch

LMBC-600

Wireless

Network Bridge

Network Switch

LMBR-600

Border Router

Line

Voltage

Room

Controller

(LMRC-112)

Line Voltage

Switched with

0-10 Volt control

Dimming Ballast

LED Driver, etc.

Load

Examples

(any relay)

Switched

etc.

Class 1 Dimming

(Class 2 also available)

Attach the LMRJ Local Network Cable

LED INDICATORS

The bridge has two LED indicators visible when the top cover is closed or open

Blue LED

• Blinking – network traffic associated with a border router

• Solid – device is active but not connected to a border router

Red LED

• Blinking – DLM Local network IRB traffic

LMBC-600 START-UP PROCESS

The following information is intended for use by a Wattstopper authorized start-up technician.

IMPORTANT: Ensure all border routers are installed and powered off (LMRJ unplugged or breaker off) before installing wireless bridges.

For multi story installations, please follow the steps below for each floor.

1. Using a Wattstopper LMRJ Cat5e cable, connect the wireless bridge by plugging the Cat5e cable into an available RJ45 port on

both the bridge and any room controller inside the space or zone to be networked. Once connected to the room controller, the

bridge will power on.

2. After power up sequence(less than 30 seconds), a solid BLUE led indicates the wireless radios are active and searching for border

routers. The BLUE led will remain solid until it has associated with a border router(LMBR-600).

3. Power on all border routers installed in the space or on the individual floor

4. Bridges will automatically discover and join the panID of available border routers. Once this happens, the BLUE led will begin to

blink periodically.

5. Confirm that all wireless bridges are powered on with the BLUE led blinking. Once verified the bridge installation for the area or

floor is complete.

6. Important: For Multi-story deployments, it is recommended that all border routers be powered off to avoid bridges connecting to

border routers on different floors. This method ensures more robust wireless communication between wireless nodes and easier

system startup and management.

7. When all floors have been installed per the steps 1-6, the system is ready to be commissioned by a remote or on-site authorized

Wattstopper Startup technician.

SECURITY NOTE: All wireless communication between the bridge and border router is encrypted throughout the entire install process

using default network settings and trusted hardware pre-shared encryption keys. During system startup, security is updated from default

settings to site specific settings to provide additional levels of security.

BRIDGE RESET

The LMBC-600 wireless bridge can be reset manually on the device or remotely through software.

Hardware Reset to Factory Default Network and Security Settings

1. Open the hinged bridge cover to by pressing and lifting (show product image).

2. With the cover open, locate the small reset hole in the bottom right hand corner.

3. The hole is sized to accept a standard size paper clip.

4. Insert paper clip into reset hole to access reset button, press and hold for 10 seconds to reset back to factory default network and

security settings.

Software Reset Using LMCS (Advanced method)

1. Connect laptop with LMCS directly to the DLM room IRB or connect to the DLM BACnet network. See the LMCS User manual for

details on setting up LMCS to communicate with a DLM network.

2. Locate the bridge device(s) to be reset in the LMCS device tree.

3. Click the bridge to access device properties.

4. On the Advanced tab, choose from a list of reset options.

a. Reset network and security settings to default.

b. Reset security settings only.

TROUBLESHOOTING

LMBC-600 LEDs fail to illuminate

Check LMRJ Cat5e connections

Blue LED fails to enter blinking state

Check to make sure border router is powered on

800.879.8585

www.legrand.us/wattstopper

No. 25224 – 08/17 rev. 3

Wattstopper warranties its products to be free

of defects in materials and workmanship for a

period of five (5) years. There are no obligations

or liabilities on the part of Wattstopper for

consequential damages arising out of, or in

connection with, the use or performance of this

product or other indirect damages with respect

to loss of property, revenue or profit, or cost of

removal, installation or reinstallation.

Wattstopper garantit que ses produits sont

exempts de défauts de matériaux et de fabrication

pour une période de cinq (5) ans. Wattstopper

ne peut être tenu responsable de tout dommage

consécutif causé par ou lié à l’utilisation ou

à la performance de ce produit ou tout autre

dommage indirect lié à la perte de propriété, de

revenus, ou de profits, ou aux coûts d’enlèvement,

d’installation ou de réinstallation.

Wattstopper garantiza que sus productos

están libres de defectos en materiales y mano

de obra por un período de cinco (5) años. No

existen obligaciones ni responsabilidades por

parte de Wattstopper por daños consecuentes

que se deriven o estén relacionados con el

uso o el rendimiento de este producto u otros

daños indirectos con respecto a la pérdida

de propiedad, renta o ganancias, o al costo

de extracción, instalación o reinstalación.

WARRANTY INFORMATION INFORMATIONS RELATIVES À LA GARANTIE INFORMACIÓN DE LA GARANTÍA

FCC Notice

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful

interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Legrand LMBC-600 User manual

Brand: Legrand

Model: LMBC-600

Category: Bridges & repeaters

Type: User manual

This manual is also suitable for

DLM Wireless Network Bridge Module Quick Start

Download PDF

report

in other languages

français: Legrand LMBC-600 Manuel utilisateur

Legrand LMBC-600 User manual

This manual is also suitable for

Legrand LMBC-600 User manual

in other languages

Related papers

Other documents