tekmar tN2 House Control 401 Quick Set-up

1

A Watts Water Technologies Company

401_Q

02/14

Replaces: 01/14

HVAC Systems

Quick Setup Guide

tekmarNet

®

2 House Control 401

1. Location 2. Install Junction Box

3. Install Sensors 4. Line Voltage Wiring

OR

115 V (ac)

NGL

N

L

(red)

(black)

to pump

grounds

Back of

House Control 401

Zone 2

Zone 3

Zone 4

DHW

Zone 1

401

Zone 4

Zone 3

Zone 2

Zone 1

DHW Pump

Pump Power

Strip wires 1/2 inch

(13 mm). Installed

wires are not removable.

12-18 AWG

Pipe Sensors

Sensor Well

Retaining Clip

Universal

Sensor 082

401 401

Outdoor Sensor

Sensor with rear

entry wiring

Sensor with bottom

entry wiring

Sensor mounted onto

2" x 4" electrical box

2

A Watts Water Technologies Company

6. Low Voltage Wiring

M

e

n

u

H

o

u

s

e

C

o

n

t

r

o

l

4

0

2

I

t

e

m

7. Install Cover

R

C

L

N

Expansion

tN4 Boil

CtN4

Modulating

Boiler

—+

2

1

Back of

House Control 401

Menu

House Control 401

Item

+

ComBoil Out DHWCom

Zone 1

H8006C

Zone 2 Zone 3 Zone 4

tN2 tN2 tN2 tN2 tN2 tN2 tN2 tN2

Sensors - No Power

Call Call

tN4 C

Mod dc/mA Boil Exp.

Setpoint DHW

RC

Input Power

Use at least 167°F

(75°C) conductors

Stage 2Stage 1

24 V (ac) Transformer 009

DHW Call

from DHW

Tank Aquastat

(optional)

Setpoint Call

Outdoor

Sensor

070

Boiler Supply

Sensor 082

DHW Tank

Sensor 082

One or Two Stage

Boiler T-T

tekmarNet

®

2 Thermostats

tekmarNet

®

4

Expansion to

Wiring Centers,

Timers, or

User Switch

5. Install Enclosure

3

A Watts Water Technologies Company

8. User Interface

9. Access Level

MONITOR

VIEW

ADJUST

MAXMIN

Boil Exp

DHW Setp

Zones

DHW 1 2 3 4

1 2

AM

min

sec

hr

PM

Calls

Pumps WWSD Saving

Item Field

Displays the name

of the selected item

Number Field

Displays the

current value of

the selected item

Status Fields

Displays the current

status of the control’s

inputs, outputs and

operation. Most symbols

in the status field are

only visible when the

VIEW Menu is selected

Menu Field

Displays the

current menu

Calls

CALLS

Displays any call for heat the control is

receiving.

Pumps

PUMPS

Displays any pump currently operating.

Zones

1 2 3 4

ZONES

Displays if an on-board zone is operating.

WARNING

Displays if an error exists on the system.

Saving

ENERGY SAVING INDICATOR

Displays when the system is saving

energy. See the Saving Indicator section.

WWSD

Displays when the system is in Warm

Weather Shut Down.

°F°C

minhr

sec%

°F, °C, %, HOURS, MINUTES, SECOND

Units of measurement for current number.

UNOCCUPIED

Indicates that a User Switch or Timer has

put the system into UnOccupied.

BOILER

Indicates that the boiler should be

heating.

MAXMIN

MIN / MAX

Displays when an operating temperature

reaches a minimum or maximum value.

Symbols

Display

INST (Installer)

or USER

Default = INST

ACCESS LEVEL

Selects the Access Level of the control, which determines the Menu items

available. USER provides the most limited level of access and shows

the fewest possible items.

When set to USER, all thermostats are locked and the number of thermostat

settings available are reduced.

Press menu button until the Toolbox Menu is displayed. Press

item button to locate the access level setting.

4

tekmar Control Systems Ltd.,

A Watts Water Technologies Company

All specifications are subject to change without notice.

Printed in Canada. 401_Q - 02/14.

tekmar Control Systems Ltd., A Watts Water Technologies Company.

Head Ofﬁ ce: 5100 Silver Star Road,

Vernon, B.C. Canada V1B 3K4, 250-545-7749, Fax. 250-545-0650 Web Site: www.tekmarControls.com

Press menu button until the Adjust Menu is displayed. Press item button

to locate the desired setting.

Item Field Range Access Description Set to

ADJUST

-60 to 45°F

(-51.0 to 7.0°C)

Default = 10°F

(-12.0°C)

Installer

OUTDOOR DESIGN

Typically set to the temperature of the coldest day of

the year. The outdoor air temperature used in the boiler

heating curve is used to determine the boiler target

temperature.

EMS2,

EMS1,

4-20

0-10,

2STG,

1STG

Default = 1STG

Installer

BOILER TYPE

The type of boiler connected to the control.

1STG = single one-stage on-off boiler

2STG = single two-stage on-off boiler

0-10 = 0-10 V (dc) modulating boiler

4-20 = 4-20 mA modulating boiler

EMS1 = tekmar boiler staging controls

EMS2 = Viessmann modulating boilers with

OpenTherm

VIEW

70 to 200°F

(21.0 to 93.5°C)

Default = 180

°F

(82.0°C)

Installer

BOILER DESIGN

The supply water temperature required for the boiler

zones to heat the building on the typical coldest day

of the year. Recommendations:

High mass radiant floor = 120°F (50°C)

Low mass radiant floor = 140°F (60°C)

Fancoil or air handling unit = 190°F (90°C)

Copper fin-tube convector = 180°F (80°C)

Radiators = 160°F (70°C)

Low profile baseboard = 150°F (65°C)

10. Critical Settings

Page is loading ...

tekmar tN2 House Control 401 Quick Set-up

This manual is also suitable for

tekmar tN2 House Control 401 Quick Set-up

in other languages

Related papers

Other documents