Vizio XMA1200 Quick Install Manual

Brand: Vizio

Model: XMA1200

Type: Quick Install Manual

XMA1200 - QUICK INSTALL GUIDE

FULL ARTICULATING MOUNT

UNIVERSAL FOR 40” - 60” TVS UP TO 120 LBS

IMPORTANT SAFETY INFORMATION

Read the Important Safety Information on this page before installing or using this mounting system.

Always follow the instructions in this Quick Install Guide. VIZIO is not liable for damage or injury caused by incorrect

mounting, assembly, or use.

This mount ﬁts most screens from 40” to 60”.

This mounting system supports a maximum weight of 120 lbs and a maximum screen size of 60”. Attaching a screen

that is larger or heavier than speciﬁed above may result in personal injury or damage to your TV.

If you have any doubts about the ability of the wall to support the mounting system or your TV, do not install the

mounting system. Contact a qualiﬁed contractor.

Only attach this mount system to vertical walls as instructed in this Quick Install Guide.

Keep all contents of this box away from small children. This product contains small items that could be a choking

hazard if swallowed.

This mounting system is for indoor use only.

STEP 1 - BEFORE YOU BEGIN

YOU WILL NEED

Power Drill 1/2” (12.5mm) Concrete Drill Bit 7/32” (5.5mm) Drill Bit

Pencil Electronic Stud FinderPhillips-head Screwdriver Assorted Wrenches

Level

Before you begin the installation, ensure you have all of the items listed on this page. Do

not begin the installation unless you have all of the following items.

Mounting a TV requires lifting. To make the installation easier and

safer, have someone help you. Always lift properly.

Mounting a TV requires power tools. If you are unfamiliar with

safe power tool use, consult a professional installer.

TWO-PERSON JOB

Not Included

STEP 2 - REVIEW THE PACKAGE CONTENTS

Before you begin, ensure all parts are included and undamaged. To prevent loss, do not unpack the small parts until

they are required. If any parts are missing or damaged, contact VIZIO Customer Service (877) 698-4946.

x 1

x 2

x 4

Sec X1

x 2

x 4

x 1x 4

x 1

(Attached to Mount)

Quick Install Guide &

Wall-Mount Template

x 4

x 4 x 4

x 4

x 4 x 4 x 4

x 4 x 4

x 4

MISC

x 4 x 4 x 4

LAG

x 6 x 6

ANCHOR

x 6

STEP 3 - CHOOSE THE DIRECTION OF SWING ARM

The mount features an arm designed to swing away from the wall

like a door. Like a door, the mount can swing open to the left or to

the right.

Before you begin the installation, you must decide which direction

you want the arm to swing–to the left or to the right.

If you want the arm to swing to the left, do nothing. The mount is

ready to swing to the left as it is assembled in the box.

Go to Step 4 on page 7.

Mount in Box - Ready to Swing Left

Arm Swings Left Arm Swings RightOR

If you want the mount to swing to the right:

1. Lay the mount on the ﬂoor. Using the screwdriver, remove the 2

philips-head screws as shown.

2. Hold down the mount as shown and swing the arm away from

the mount.

3. Using the screwdriver, remove the remaining 4 phillips-head

screws from the arm. There are 2 screws inside the arm and 2

screws on the top of the arm.

Hold Down

Swing Arm

Away

On the top of the arm, do not loosen the screws inside the

row of 9 holes. The correct screws are close to the hinge.

4. Gently separate the arm from the mount.

5. Flip the arm over, then gently reattach the arm to the mount.

6. Using the phillips-head screwdriver, replace the 6 phillips-head

screws. Note that the tab should be on the top of the arm.

The arm is ready to swing to the right.

Go to Step 4 on page 7.

Separate Arm

from Mount

Flip Over

Then Reattach

Top of Arm

Has Tab

STEP 4 - SET THE LENGTH OF SWING ARM

If you are mounting a 40 - 52” TV, you can adjust the swing arm so

that more of the mount is hidden behind the TV screen.

To adjust the length of the swing arm:

1. Find the size of your TV (reference your TV’s User Guide). Locate

the 9 holes on the top of the swing arm. Determine your TV’s

correct holes using the image at right.

2. Using the screwdriver, remove the 4 screws from the swing arm

as shown. There are 2 screws on the top and 2 inside the wire

management canal on the bottom.

3 4

Swing Arm

40 - 48” 50 - 52” 55 - 60”

If your TV is wider than usual due to side speakers or a

large frame/bezel, use holes set for a larger TV.

3. Push on the end of the swing arm to shorten it. Ensure the holes

for the screws are aligned with the correct holes for your TV’s

size:

• For TVs 40 - 48” use the innermost holes.

• For TVs 50 - 52” use the middle holes.

• For TVs 55 - 60” use the outermost holes.

4. Using the phillips-head screwdriver, replace the 4 screws.

The swing arm is adjusted.

• If you are installing the mount on a wall with wood studs,

go to Step 5A on page 9.

• If you are installing the mount on a concrete wall,

go to Step 5B on page 13.

40 - 48” 50 - 52” 55 - 60”

Push End of

Swing Arm

3 4

STEP 5A - MOUNTING TO A WALL WITH WOOD STUDS

The mount can be attached to walls with wood studs. The wall

covering (drywall, lath, plaster, etc.) may not be thicker than 1/2”.

To attach the mount:

1. Use the electronic stud ﬁnder to locate two studs in the wall.

The studs should be approximately 16” apart. Use the pencil to

mark the areas of the wall where the studs are located.

2. Hold the template against the wall, using the pencil marks as a

guide. Ensure 4 holes in the template line up with the studs.

Use the level to level the template.

When the template is level, tape it in place.

16”

Ensure 4 holes in

template line up

with studs

Level

3. Using the power drill and the 7/32” drill bit, drill into the top two

template holes. Drill about 2” into the studs.

Remove the template from the wall.

4. Remove 2 lag bolts and 2 washers from the pouch labeled LAG.

Use a wrench to insert the lag bolts and washers into the holes

you just drilled. Do not insert the lag bolts completely. Leave 1/2”

of the bolt showing.

5. Remove the plastic covers from the mount. Use the thumb holes

to lift the covers away from the mount.

Save the plastic covers. They will be reattached in Step 7.

6. Hang the mount on the wall using the 2 lag bolts, then slide the

mount so the lag bolts are resting in the narrow part of the slot.

Narrow part of slot

Mount, then slide

Use the

Thumb Hole

7. Ensure the mount is level. Make any necessary adjustments, then

use a wrench to tighten the top 2 lag bolts.

Ensure the bottom mount holes are over a stud. Using the power

drill and the 7/32” drill bit, drill 2 holes in the bottom two mount

holes.

Drill about 2” into the studs.

8. Remove 2 lag bolts and 2 washers from the pouch labeled LAG.

Use a wrench to tighten the lag bolts and washers into the 2

holes you just drilled. Insert the lag bolts completely.

The mount is attached to the wall.

Go to Step 6 on page 16.

STEP 5B - MOUNTING TO A CONCRETE WALL

1. Hold the template against the wall, using the level to level the

template.

When the template is level, tape it in place.

2. Using the power drill and the 1/2” drill bit, drill into 6 of the

template holes as shown. Drill about 2 1/2” deep.

Remove the template from the wall.

Level

(choose one)

3. Remove 6 anchors from the pouch labeled ANCHOR.

Push the anchors into the holes you just drilled. Ensure the

anchors are completely inserted and ﬂush with the wall.

4. Remove 6 lag bolts and 6 washers from the pouch labeled LAG.

Use a wrench to tighten the lag bolts and washers into the

anchors. Do not insert the lag bolts completely. Leave 1/2”

of the bolt showing.

5. Remove the plastic covers from the mount.

Save the plastic covers. They will be reattached in Step 7.

6. Hang the mount on the wall using the 6 lag bolts, then slide the

mount so the lag bolts are resting in the narrow part of the slot.

Verify that the mount is level. Make small adjustments before

tightening all 6 lag bolts.

The mount is attached to the wall.

Go to Step 6 on page 16.

Narrow part of slot

Mount, then slide

STEP 6 - ATTACHING THE TV BRACKETS

1. Gently place the TV on the ﬂoor screen-down. You may want to

place a rug or blanket beneath the screen to prevent scratches.

In your TV’s User Guide, ﬁnd the size of your TV’s mounting holes.

These will be listed as M4, M5, M6, or M8.

Open the pouch labeled with the size that matches your TV’s

mounting holes. If you do not have the User Guide, or the size is

not listed, you may have to try several sizes until you ﬁnd one

that ﬁts.

2. Place the vertical TV brackets against the mounting holes as

shown. Center them over the mounting holes on the back of the

TV.

If you have a large screen (mounting holes are 400-600mm

apart), place the brackets inward.

If you have a small screen (mounting holes are 200mm apart),

place the brackets outward.

Brackets Inward Brackets OutwardOR

Mounting Holes

Back of TV

3. Using the screwdriver, insert the screws, star washers, and

washers as shown.

Because each TV is different, your VIZIO TV mount includes

screws of different lengths. Use screws that can be inserted

completely.

Do not use a short screw if a longer screw can be

inserted completely.

If your TV has a curved back, or if your TV has

protruding components, place spacers between the

brackets and the mounting holes. The spacers are in

the pouch labeled MISC.

If using the M4 or M5 screws, use the small spacers.

If using the M6 or M8 screws, use the large spacers.

Without Spacer With Spacer

4. Center the horizontal brackets over the vertical brackets as

shown.

Open the pouch labeled Sec X1 and remove 4 nuts and

their 4 matching screws.

5. Insert the screws through both the horizontal and vertical TV

brackets. Ensure you attach both the top and bottom horizontal

brackets.

The TV brackets are attached. Go to Step 7 on page 19.

x 4

Page is loading ...

Vizio XMA1200 Quick Install Manual

Vizio XMA1200 Quick Install Manual

Vizio XMA1200 Quick Install Manual

Related papers

Other documents