Hampton Bay 28236 User guide

Brand
Hampton Bay
Model
28236
Type
User guide

This manual is also suitable for

1-LIGHT EXTERIOR WALL LANTERN
1-855-HD-HAMPTON
WWW.HAMPTONBAY.COM
THANK YOU
continually create
quality products designed to enhance your home. Visit us online to see our full line of products available for your home improvement needs.
Thank you for choosing Hampton Bay!
Questions, problems, missing parts? Before returning to the store,
call Hampton Bay Customer Service
8 a.m. – 7 p.m., EST, Monday – Friday, 9 a.m. – 6 p.m., EST, Saturday
Item#1007158019
1007259777
Model#28235
28236
Table of Contents
Safety Information
Table of Contents .......................................................2
Safety Information .....................................................2
Limited Warranty........................................................2
What is Covered ....................................................2
What is not Covered ..............................................2
Pre-Installation .......................................................... 3
Tools Required (not included) ...............................3
Hardware Included ..............................................................3
Package Contents ................................................................4
Installation..............................................................................5
Clear and Cleaning .................................................................6
□Consult a qualified electrician if you have any electrical
questions.
CAUTION: Inspect the wire insulation for any cuts,
abrasions, or exposed copper that may have resulted
during shipping. If there is a defect in the wire, do not
attempt installation. Please call our Customer Service
Team at 1-855-HD-HAMPTON.
WARNING: Before starting installation of this fixture or
removal of a previous fixture, disconnect the power by
turning off the circuit breaker or by removing the fuse at
the fuse box.
2
Service Parts . ........................................................................ 6
Troubleshooting.....................................................................6
Contact the Customer Service Team at 1-855-HD-HAMPTON or visit WWW.HAMPTONBAY.COM.
three (3) years from
date of purchase. This warranty applies only to the original consumer purch aser and only to products used in normal use and service. If this
product is found to be defective, the manufacturer’s only obligation, and your exclusive remedy, is the repair or replacement of the product at
the manufacturer's discretion,provide that product has been damaged through misuse,abuse,accdient,modeifications,alterations, neglect or
mishandling. This warranty shall not apply to any product that is found to have been improperly installed, set up, or used in any way not in
accordance with the instructions supplied with the product. This warranty shall not apply to a failure of the product as a result of an accident,
misuse, abuse, negligence, alteration, or faulty installation, or any other failure not relating to faulty material or workmanship.This warranty
shall not apply to the finish on any protion of the product,such as surface and/or weathering,as this is considered normal wear and tear.
3
Pre-Installation
HARDWARE INCLUDED
NOTE: Hardware not shown to actual size.
（ ）
Part Description Quantity
AAMounting bracket 1
BBMounting screw (Pre-assembled
to mounting bracket (AA))2
CCOutlet box screw 2
DDGreen ground screw (Pre-assembled
to mounting bracket (AA))1
Part Description Quantity
EEHex nut 2
FFWire connector 3
GGRubber washer 2
HHCap nut 2
AA
BB
CC
DD
EE
FF
GG
HH
Phillips
Screwdriver
Safety
Goggles
Wire
Stripper
Electrical
Tape
Pliers
Caulk
WWW.HAMPTONBAY.COM
Please contact 1-855-HD-HAMPTON for further assistance.
Pre-Installation
PACKAGE CONTENTS
A
B
4
Part Description Quantity
AFixture body 1
BGlass piece 4
5
Installation
1Installing the mounting bracket WARNING: Turn off power at the circuit breaker and the
light switch. Ensure the power is off before continuing.
2Connecting the wires
Unscrew the two cap nuts (HH) and rubber washer(GG) from the
mounting screws (BB). Remove the mounting bracket (AA)from
the fixture body (A), and keep the cap nuts (HH) and rubber
washer (GG) for later use. Loosen the hex nuts (EE) on the
mounting screws (BB) and adjust the mounting screws (BB) so
that they extend long enough to protrude the canopy of the
fixture body (A), then secure the mounting screws (BB) in place
using the hex nuts (EE).
3
□
AGG
HH
AA
EE
BB
□
AACC
Fasten the mounting bracket (AA) onto the outlet box using
two outlet box screws (CC).The side of the mounting bracket
(AA) marked "GND" must face out.
□
□
Installing the light fixture
Place the fixture body (A) over the outlet box, and ensure the
heads of the mounting screws (BB) come through the holes of
the fixture body (A). Place the rubber washers (GG) over the
mounting screws (BB), and tighten the cap nuts (HH) onto the
mounting screws (BB) until the fixture body (A) is held firmly
against the wall. Use weather resistant caulk (not included) to
seal around the top and side perimeter of the back plate of the
fixture body (A). Do not caulk the bottom of the back plate to
allow for condensation evaporation.
GG HH
FF
White
Outlet box
BB
Base
Black
Ground wire
Connect the white wire from the light fixture to the white
supply wire from the junction box using a connector (FF).
Connect the black wire from the light fixture to the black
supply wire from the junction box using a connector (FF).
Connect the ground wire from the light fixture to the ground
supply wire from the junction box using a connector (FF). Push
the wires into the junction box. Mount the fixture body (A) onto
the mounting bracket (AA) and secure with the mounting
screws (BB).
WWW.HAMPTONBAY.COM
Please contact 1-855-HD-HAMPTON for further assistance.
A
AA
A
Install the light bulb (not
included) in the socket of
fixture body (A). Use one
maximum 4W Type A medium
base LED bulb or one
maximum 60W Type A medium
base regular filament Edison
bulb .
BB
6
Care and Cleaning
□Do not use any cleaners with chemicals, solvents, or harsh abrasives. Use only a dry, soft cloth to dust or wipe carefully.
□To clean the fixture, disconnect power by turning off the circuit breaker or by removing the fuse at the fuse box. Use a dry or slightly
dampened, clean cloth to wipe the exterior surface of the fixture.
Troubleshooting
Problem Possible Cause Solution
The bulb will not light. The bulb is burned out. Replace the bulb.
The power is off. Ensure the power supply is turned on.
The power cord is not plugged in. Ensure the power cord is plugged into the outlet.
The circuit breaker is off. Ensure the circuit breaker is set to the "ON" position.
The fuse blows, or the circuit breaker
trips, when the light is turned on.
There are crossed wires, or the power
wire is grounding out.
Discontinue use of the lamp. Check the wire connections.
Contact a qualified electrician or call the Customer Care
Service Team at 1-855-HD-HAMPTON.
Service Parts
MODEL TYPE : 28235 28236
AABBCCDD
EEFF GGHH
Part Description Quantity
AAMounting bracket 1
BBMounting screw
(Pre-assembled to mounting bracket (AA))
2
CCOutlet box screw 2
DDGreen ground screw
(Pre-assembled to mounting bracket (AA))
1
Part Description Quantity
EEHex nut 2
FFWire connector 3
GGRubber washer 2
HHCap nut 2
Questions, problems, missing parts? Before returning to the store,
call Hampton Bay Customer Service
8 a.m. – 7 p.m., EST, Monday – Friday, 9 a.m. – 6 p.m., EST, Saturday
1-855-HD-HAMPTON
WWW.HAMPTONBAY.COM
Retain this manual for future use.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7

Hampton Bay 28236 User guide

Brand
Hampton Bay
Model
28236
Type
User guide
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers