Celestron 22006 User manual

Brand: Celestron

Model: 22006

Category: Telescopes

Type: User manual

Celestron 22006 is a versatile telescope designed for both terrestrial and celestial observations. With its 3x Barlow lens and a range of eyepieces, it offers variable magnification for detailed viewing of distant objects. The smartphone adapter allows you to capture images and videos through the telescope's lens, making it a great tool for astrophotography and nature photography. Additionally, the Bluetooth remote enables convenient shutter control for your smartphone camera.

INSTRUCTION MANUAL

Model #22006

* SOLAR WARNING! Never attempt to view the sun through any telescope

without a proper solar filter!

Pg. 2

ASSEMBLY

Set up your Travel Scope 60 indoors the first time and familiarize yourself with the correct assembly procedure before attempting it outdoors.

SETTING UP THE TRIPOD

1. The tripod comes preassembled. Stand the tripod upright and pull the tripod legs outward until each leg is

fully extended.

2. You can raise the tripod legs to the height you desire. At the lowest level, the height is about 16” (41 cm) and

extends to about 49” (125 cm).

3. To raise the height of the tripod, unlock the tripod leg lock clamps at the bottom of each tripod leg by opening

the clamp for each section and pulling outward. Once a clamp is unlocked, pull the tripod leg out as far as it will

go, and then close the leg lock to secure it. Continue doing this for each tripod leg and each section to raise the

height to the level you desire.

4. If you want to raise the tripod height up further, use the central column locking knob. Turn the locking knob

counterclockwise until loose. Then, pull up on the head of the tripod. Continue pulling to the height you desire

and then tighten the locking knob.

Objective Lens

(under lens shade)

Optical Tube

Focus Knob

Finderscope

Smartphone Adapter

Bluetooth Remote

Erect Image

Diagonal

Tripod

Central Column Locking Knob

Tripod Head Platform

Pan Handle

OTHER INCLUDED ACCESSORIES:

PARTS LIST

We recommend saving your telescope box so it can be used to store the telescope when it is not in use. Unpack the box carefully as

some parts are small. Use the parts list below to verify that all parts and accessories are present.

WHAT’S IN THE BOX

1.25” Moon Filter

20 mm Eyepiece

8 mm Eyepiece

3x Barlow Lens

Travel Backpack

BONUS SOFTWARE INCLUDED

Enhance your astronomy experience by downloading our free software for PC and Mac plus our free SkyPortal planetarium app for iOS and Android.

Windows:

- Windows 7 or higher

- 500 MHz or higher processor

- 128 MB RAM

- 850 MB of hard disk space

- 32 MB OpenGL capable graphics card

- Minimum recommended monitor resolution of 1024

x 768 pixels

Mac:

- Universal Binary (PPC/Intel compatible)

- OS X 10.4 or higher (10.5 or higher)

- G3 450 MHz or higher processor

- 128 MB RAM

- 850 MB of hard disk space

- 32 MB OpenGL capable graphics card

- Minimum recommended monitor resolution of 1024 x 768 pixels

Pg. 3

ATTACHING THE TELESCOPE OPTICAL TUBE TO THE TRIPOD

The telescope optical tube attaches to the tripod using the mounting bracket on the bottom of the optical tube and the tripod head platform. Before starting, make

sure all of the knobs on the tripod are locked.

1. Remove the protective paper covering the optical tube.

2. Loosen the top right knob by turning it counterclockwise. This allows you to

tilt the tripod platform up 90°. After tilting the platform up, tighten the knob to

secure it in place.

3. The images show the bottom of the optical tube, the tripod platform, and

where they will attach to each other.

4. Under the center of the tripod platform, you will see a knob that contains a ¼ x

20 screw to attach the platform to the telescope optical tube.

5. You can put the ¼ x 20 screw into the threaded hole of the Travel Scope 60 in the mounting bracket of the telescope optical tube. Hold the optical tube with

one hand while threading the screw clockwise until tight with the other hand.

6. Lastly, loosen the knob for the tripod platform and lower the platform down to the level position. Then, tighten the knob securely.

MOVING THE TRAVEL SCOPE MANUALLY

The Travel Scope is easy to move wherever you want to point it. The up and down (altitude) is controlled

by the pan handle. The side-to-side (azimuth) motion is controlled by the azimuth locking knob. Both knobs

are loosened when turned counterclockwise and tightened when turned clockwise. When both knobs are

loose, you can find objects easily and then lock the controls.

INSTALLING THE DIAGONAL AND EYEPIECE

The diagonal is a prism that diverts the light at a right angle to the light path of the telescope. This allows

you to observe in a position that is more comfortable than if you had to look straight through. The Travel

Scope diagonal is an erect image model that corrects the image to be right side up and oriented correctly

left-to-right which is much easier to use for terrestrial observing. The diagonal can be rotated to any

position.

To install the diagonal and eyepiece:

1. Make sure the two thumb screws on the rear of the telescope tube do not protrude into the opening

before installation. Remove the cap from the opening at the rear of the telescope tube, and the caps

from the barrels on the diagonal. Insert the small barrel of the diagonal all the way into the rear opening

of the telescope tube. Then tighten the two thumb screws.

2. Put the chrome barrel end of one of the eyepieces into the diagonal and tighten the thumb screw.

When doing this, make sure the thumb screw is not protruding into the diagonal.

Locking Knob

Diagonal

Eyepiece

Thumb Screws

Optical Tube

Pg. 4

CENTER THE TARGET

IN THE EYEPIECE

Look through the telescope using your lower powered

eyepiece. Move the telescope until the object you chose lies

in the center of the view. If the image is blurry, gently turn the

focus knobs until it comes into sharp focus.

LOOK THROUGH FINDERSCOPE

Once the object is centered in your 20mm eyepiece, look

through the finderscope and locate the crosshair reticle.

ADJUST THE FINDERSCOPE

Without moving the telescope, use the three finger knobs

on the finderscope bracket to move the finder around in the

bracket until the crosshair appears over the same object you

are observing in the telescope’s 20mm eyepiece.

TIP: Try adjusting one screw at a time. Loosen one screw by

half a turn and tighten another by the same amount to

ensure the finderscope is securely held in place.

YOUR FINDERSCOPE IS

NOW ALIGNED!

It should not require realignment unless it is bumped

or dropped.

The finder is one of the most important parts of your telescope. It helps you

locate objects and center them in the eyepiece. The first time you assemble

your telescope, you need to align the finder to the telescope’s main optics.

It’s best to do this during the day*.

* SOLAR WARNING! Never attempt to view the sun through any

telescope without a proper solar filter!

CHOOSE A TARGET

Take the telescope outside during the day and find an easily

recognizable object, like a streetlight, license plate or sign.

The object should be as far away as possible, but at least a

quarter mile away.

2Low Power Eyepiece

Focus Knobs

Objective Lens EyepieceAdjustment Screws

ALIGNING THE FINDERSCOPE

Pg. 5

TELESCOPE BASICS

FOCUSING

To focus your Travel Scope turn the focus knob located near the rear of the telescope.

NOTE: Remove the front lens cap of the TravelScope optical tube prior to attempting your observation.

NOTE: If you wear glasses, you may want to remove them when observing with an eyepiece attached to the telescope. However, if you have astigmatism, corrective lenses should be worn at all times.

USING THE SMARTPHONE ADAPTER

Use the phone clamp knob to open the phone holder so that

your phone fits inside. Tighten it to secure your phone in place.

Loosen the knob on the bottom of the adapter that secures the

phone clamp to the eyepiece clamp. Slide the phone clamp up

and down and rotate it left and right until your camera is looking

down through the eyepiece of the telescope. Tighten the knob

on the bottom of the adapter to secure it in place.

Use the telescope’s focuser to adjust focus of your camera.

Snap the image using your app.

Open the eyepiece clamp and place it around the body of the

eyepiece. Tighten the clamp until it’s secure.

4 5

Turn on the phone and open your camera app. Make sure the

flash is turned off.

INSTALLING & USING THE BARLOW LENS

Your telescope also comes with a 3x Barlow lens which triples the magnifying power of each eyepiece.

To use the Barlow lens, insert the Barlow between the diagonal and the eyepiece.

NOTE: Start by using a low power eyepiece as it will be easier to focus.

To use the moon filter, simply thread the filter to the chrome barrel of the eyepiece.

3x Barlow Lens

Moon Filter

on Eyepiece

Pg. 6

Press and hold the button on the remote for 5 seconds. A blue

light will turn on and, after a few seconds, start to blink. The

remote is now in pairing mode.

Open your camera app. Press the button on the remote to trigger

the shutter on your phone.

If your camera is in video mode, you can press the button once

to start recording and again to stop the recording.

To insert or replace the battery, place your thumb in the center

of the back cover, pressing inward and sliding downward remove

the battery door. The CR2032 battery should be inserted with the

positive (+) side facing upward. Replace the cover.

Using the Bluetooth settings on your phone, pair the device

called “GBshutter”.

GENERAL OBSERVING HINTS

When using any optical instrument, there are a few things to remember to ensure you get the best possible image.

• Never observe through window glass. Glass found in household windows is optically imperfect and may vary in thickness from one part of a window to the next.

This inconsistency can and will affect the ability to focus your telescope. In most cases you will not be able to achieve a truly sharp image, while in some cases

you may actually see a double image.

• Never look across or over objects that are producing heat waves. This includes asphalt parking lots on hot summer days or building rooftops.

• Hazy skies, fog and mist can also make it difficult to focus when viewing terrestrially. The amount of detail seen under these conditions is greatly reduced.

NOTE: Your telescope was designed for terrestrial observation as well as celestial viewing.

USING THE BLUETOOTH REMOTE

Pg. 7

SAFETY INSTRUCTIONS

• Risk of explosion if battery is replaced by an incorrect type.

• The included battery is not rechargeable.

• Please use the battery in its original purpose to avoid causing the battery to short circuit. When the conductive material is connected directly to the battery

positive and negative will cause a short circuit.

• Do not use a damaged battery.

• Keeping the battery in an extremely cold or very hot location can result in shortened battery life.

• When replacing the battery, please refer to the instruction manual and pay attention to the positive and negative direction of battery.

• Do not put the battery in the ﬁre. Dispose of the battery according to local regulations.

FCC NOTICE: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful

interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

FCC IDENTIFIER: 2A2FG-93974 FCC certiﬁcation is for the Bluetooth Remote Control included with this product. Model # 93974

CAUTION: Changes or modiﬁcations not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed

to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful

interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

SOLAR WARNING

• Never look directly at the Sun with the naked eye or with a telescope unless you have the proper solar ﬁlter. Permanent and irreversible eye damage may result.

• Never use your telescope to project an image of the Sun onto any surface. Internal heat build-up can damage the telescope and any accessories attached to it.

• Never use an eyepiece solar ﬁlter or a Herschel wedge. Internal heat build-up inside the telescope can cause these devices to crack or break, allowing unﬁltered sunlight to pass through to the eye.

• Do not leave the telescope unsupervised, especially when children or adults unfamiliar with the correct operating procedures of your telescope are present.

Product design and speciﬁcations are subject to change without prior notiﬁcation.

This product is designed and intended for use by those 14 years of age and older.

Popular Science is a trademark of Camden Media, Inc., and used under license.

celestron.com/pages/warranty

Made in China

11-22