Ryobi RML18 is a versatile and powerful magnifying clamp light designed for general illumination and precision work. Equipped with a flexible gooseneck and rotating collar, it allows you to position the light exactly where you need it. Choose between high (500 lumens) and low (200 lumens) brightness levels to suit your needs. The RML18 is compatible with a range of Ryobi 18V batteries (not included), so you can power it up and get to work right away.
Ryobi RML18 is a versatile and powerful magnifying clamp light designed for general illumination and precision work. Equipped with a flexible gooseneck and rotating collar, it allows you to position the light exactly where you need it. Choose between high (500 lumens) and low (200 lumens) brightness levels to suit your needs. The RML18 is compatible with a range of Ryobi 18V batteries (not included), so you can power it up and get to work right away.
FRONT PAGE
RML18
IMPORTANT!
It is essential that you read the instructions in this manual
before assembling, operating, and maintaining the product.
Subject to technical modications.
Safety, performance, and dependability have been given
top priority in the design of your magnifying clamp light.
INTENDED USE
The magnifying clamp light is intended for general
illumination. The product can also be used as a magnifying
glass with illumination for precision works. Do not use the
product in wet conditions.
The product must be clamped during use.
The product is not intended for clamping on tubular
materials.
When clamping, the material being clamped must be pushed
to the deepest point of the clamp for increased stability.
Do not use the product for any other purpose. Use of the
product for operations different from intended could result in
a hazardous situation.
MAGNIFYING CLAMP LIGHT SAFETY WARNINGS
■The light source contained in this luminaire shall only be
replaced by the manufacturer or his service agent or a
similar qualified person.
■Use only with recommended battery pack and charger.
Any attempt to use another battery pack will cause
damage to the product and could possibly explode,
cause a fire, or personal injury.
■Do not disassemble the product.
■If wrapped or in contact with fabrics, the lens can
produce sufficient heat to melt some fabrics. To avoid
serious personal injury, never allow the lens to come in
contact with anything.
■Do not place the product or battery pack near fire or
heat. This will reduce the risk of explosion and possible
injury.
■Remove the battery pack or disconnect the mains power
before starting any work on the product.
■Do not store the product in a damp or wet location, or in
a location where the temperature may reach or exceed
40°C. For example, inside sheds, vehicles, or metal
buildings in the summer.
■Do not direct the light beam at persons or animals and
do not stare into the light beam yourself (not even from
a distance). Staring into the light beam may result in
serious injury or vision loss.
BATTERY SAFETY WARNINGS
■To reduce the risk of fire, personal injury, and product
damage due to a short circuit, never immerse your
tool, battery pack or charger in fluid or allow a fluid to
flow inside them. Corrosive or conductive fluids, such
as seawater, certain industrial chemicals, and bleach
or bleach-containing products, etc., can cause a short
circuit.
TRANSPORTING LITHIUM BATTERIES
Transport the battery in accordance with local and national
provisions and regulations.
Follow all special requirements on packaging and labelling
when transporting batteries by a third party. Ensure that
no batteries can come in contact with other batteries
or conductive materials while in transport by protecting
exposed connectors with insulating, non-conductive caps or
tape. Do not transport batteries that are cracked or leaking.
Check with the forwarding company for further advice.
MAINTENANCE
■Use only original accessories and spare parts. Should
components need to be replaced which have not been
described, please contact an authorised service centre.
All repairs should be performed by an authorised service
centre.
■Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to various types of commercial
solvents and may be damaged by their use. Use clean
cloths to remove dirt, carbon dust, etc.
■Do not at any time let brake fluids, gasoline, petroleum-
based products, penetrating oils, etc., come in contact
with plastic parts. Chemicals can damage, weaken or
destroy plastic which may result in serious personal
injury.
SYMBOLS ON THE PRODUCT
V Volts
Direct current
The rated maximum ambient temperature
Regulatory Compliance Mark (RCM). Product
meets applicable regulatory requirements.
Please read the instructions carefully before
starting the machine.
Class III protection
2
Original Instructions
Do not dispose of waste batteries, waste
electrical and electronic equipment as unsorted
municipal waste.
Waste batteries and waste electrical and
electronic equipment must be collected
separately.
Waste batteries, waste accumulators, and
light sources have to be removed from the
equipment.
Check with your local authority or retailer for
recycling advice and collection point.
According to local regulations, retailers may
have an obligation to take back waste batteries
and waste electrical and electronic equipment
free of charge.
Your contribution to the reuse and recycling
of waste batteries and waste electrical and
electronic equipment helps to reduce the
demand of raw materials.
Waste batteries, in particular containing lithium,
and waste electrical and electronic equipment
contain valuable and recyclable materials,
which can adversely impact the environment
and the human health if not disposed of in an
environmentally compatible manner.
Delete personal data from waste equipment,
if any.
SYMBOLS IN THIS MANUAL
Safety Alert
Note
Parts or accessories sold separately
3
Original Instructions
Operator’s manual
Battery port
Flexible gooseneck
Battery pack
Charger
Rotating collar
Clamp
On/off switch
LED lens
Magnification lens
Spot magnification lens
4
2
1
100%
40%
0%
1 2
5
PRODUCT SPECIFICATIONS
Magnifying LED clamp light
Model RML18
Voltage 18 V
Wattage 6.8 W
Light output (Lumens)
High brightness level 500 Lum
Low brightness level 200 Lum
Colour rendering index (CRI) 80
Correlated colour temperature (CCT) 6500 K
Weight - excluding battery pack 0.6 kg
BATTERY
Compatible battery pack (not included)
RB18L13
RB18L15
RB18L15A
RB18L15B
RB18L20
RB18L20A
RB18L25
RB18L25A
RB18L40
RB18L40A
RB18L50
RB18L50A
RB18L60A
RB18L90A
RB1815C
RB1820C
RB1825C
RB1840C
RB1840X
RB1850C
RB1850X
RB1860X
BACK PAGE
Imported by:
Techtronic Industries Australia Pty Ltd
31 Gilby Road, Mount Waverley, VIC 3149
Melbourne, Australia
Techtronic Industries N.Z. Limited
Unit C, 70 Business Parade South,
Highbrook, Auckland 2013, New Zealand
RYOBI is a trade mark of Ryobi Limited, and is used under license.
20220802v1
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
Ryobi RML18 is a versatile and powerful magnifying clamp light designed for general illumination and precision work. Equipped with a flexible gooseneck and rotating collar, it allows you to position the light exactly where you need it. Choose between high (500 lumens) and low (200 lumens) brightness levels to suit your needs. The RML18 is compatible with a range of Ryobi 18V batteries (not included), so you can power it up and get to work right away.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Ryobi RLCL18 User manual
-
Ryobi RHV18 User manual
-
Ryobi R18HVP User guide
-
Ryobi R18HVC User manual
-
Ryobi RWDV1811 User manual
-
Ryobi RSC18 User manual
-
-
-
-
Other documents
-
Milwaukee M18 FSX Cordless Reciprocal Saw User manual
-
Milwaukee C12 HZ User manual
-
-
AEG A18F10FN User manual
-
-
-
AEG FL182 Original Instructions Manual
-
Milwaukee M12 CHZ User manual
-
Milwaukee 6502642 User manual
-