RAMPAGE PRODUCTS 8827 Installation guide

Brand
RAMPAGE PRODUCTS
Model
8827
Type
Installation guide

This manual is also suitable for

RAMPAGE PRODUCTS 8827

The RAMPAGE PRODUCTS 8827 are side bars designed for 2007-2014 Jeep Wranglers. These side bars are made of 3-inch round steel and are designed to provide additional protection and functionality to your vehicle. They can be used as a step to help you get in and out of your Wrangler, or as a place to mount other accessories, such as lights or a winch.

The RAMPAGE PRODUCTS 8827 are easy to install and come with all the necessary hardware. They are also backed by a limited lifetime warranty.

Here are some of the features and possible use cases for the RAMPAGE PRODUCTS 8827:

RAMPAGE PRODUCTS 8827

The RAMPAGE PRODUCTS 8827 are side bars designed for 2007-2014 Jeep Wranglers. These side bars are made of 3-inch round steel and are designed to provide additional protection and functionality to your vehicle. They can be used as a step to help you get in and out of your Wrangler, or as a place to mount other accessories, such as lights or a winch.

The RAMPAGE PRODUCTS 8827 are easy to install and come with all the necessary hardware. They are also backed by a limited lifetime warranty.

Here are some of the features and possible use cases for the RAMPAGE PRODUCTS 8827:

RAMPAGE
P R O D U C T S
Installation Instructions
PART#:8627/8827/9427
SIDE BARS - 3” ROUND
2007- 14 JEEP WRANGLER 2 DOOR
Parts List
(1) Driver Side Bar
(1) Passenger Side Bar
(1) Passenger Side Front Mounting Bracket (B)
(1) Passenger Side Rear Mounting Bracket (D)
(1) Driver Side Front Mounting Bracket (A)
(1) Driver Side Rear Mounting Bracket (C)
(1) 4mm Allen Tool
(4) 10mm X 35mm Hex Head Bolts
(4) 10mm Nut Plates
(4) 10mm Lock Washers
(4) 10mm Fender Washers
(8) 8mm X 25mm Hex Bolts
(8) 8mm Lock Washers
(8) 8mm Flat Washers
(6) 6mm X 25MM Allen Bolts
(6) 6mm Nylock Nuts
(12) 6mm Fender Washers
(4) 8mm X 35mm Hex bolts
(4) 8mm Fender Washer
(4) 8mm Lock Washer
(A)
( C)
(B)
(D)
1. REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ
INSTRUCTIONS CAREFULLY.
2. a) For 2007 - 2011 models only. Insert a nut plate into the frame opening on the front driver side with the nut
facing up.(Figure 1)
b) For 2012+ models, there are pre-threaded holes in the under side of the floor board. They are covered by a
black piece of tape. (Figure 2)
3. Locate two factory holes on the front driver side pinch weld. Attach the Front Driver Side Mounting Bracket
to the pinch weld using the included (2) 6-1.00mm x 25mm Allen Bolt, (2) 6mm Nylock Nut, and (4) 6mm
Fender Washers (Figure 3). Do not tighten at this time.
4. a) For 2007 - 2011 models - Attach the Front Driver Side Mounting Bracket to the under side panel using the
included (1) 10mm x 35mm hex head bolt (1) 10mm lock washer and (1) 10mm flat washer. See Figure 3.
Do not tighten at this time.
b) For 2012+ models - Attached the Front Driver Side Mounting Bracket to the under sidepanel using the
included (1) 8mm x 35mm hex head bolt (1) 8mm lock washer and (1) 8mm flat washer.
Do not tighten at this time.
5. Repeat steps 2 - 4 for rear driver side, front and rear passenger side Mounting Brackets.
NOTE: You will only use (1) 6-1.00mm x 25mm Allen Bolt to attach both rear brackets to
pinch weld (Figure 4).
6. Position Driver Side Bar onto brackets. Attach Side Bar to Mounting Brackets using the included (4) 8-
1.25mm x 25mm Hex Head Bolt, (4) 8mm Lock Washers, and (4) 8mmFender Washers (Figure 5). Do not
tighten at this time.
7. Level and adjust Side Bar and Brackets, then tighten all hardware at this time.
8. Repeat steps 6 & 7 for Driver Side Bar.
9. Do periodic inspections to the installation to make sure that all hardware is secure and tight.
10. Be sure to clean and maintain your step bars regularly. It is recommended to wax the bars regularly to protect
their finish.
Figure 2
Figure 1
Nut Plate
Pre-threaded hole
on 2012 and newer
Wranglers.
Rampage Products Corona, CA
Phone: (951) 277-4949 Fax: (951) 277-2295
www.rampageproducts.com
Made in China
Figure 3
Figure 4
Figure 5
Front Driver Side shown
2007-2011 models - (1) 10mm x 35mm
Hex Head Bolt, (1) 10mm Fender washer, &
(1) 10mm Lock Washer.
2012+ models - (1) 8mm x 35mm, (1) 8mm
Lock Washer, (1) 8mm Flat Washer.
(2) 6mm x 25mm Allen Bolts, (4) 6mm
Fender washers, & (2) 6mm Lock Washers
Rear Driver Side Shown
2007-2011 models - (1) 10mm x 35mm
Hex Head Bolt, (1) 10mm Fender washer, &
(1) 10mm Lock Washer.
2012+ models - (1) 8mm x 35mm, (1) 8mm
Lock Washer, (1) 8mm Flat Washer.
(1) 6mm x 25mm Allen Bolts, (2) 6mm
Fender washers, & (1) 6mm Lock Washers
(2) 8mm x 25mm Hex Head Bolts, (2)
8mm Fender washers, & (2) 8mm Lock
Washers at each bracket.
  • Page 1 1
  • Page 2 2

RAMPAGE PRODUCTS 8827 Installation guide

Brand
RAMPAGE PRODUCTS
Model
8827
Type
Installation guide
This manual is also suitable for

RAMPAGE PRODUCTS 8827

The RAMPAGE PRODUCTS 8827 are side bars designed for 2007-2014 Jeep Wranglers. These side bars are made of 3-inch round steel and are designed to provide additional protection and functionality to your vehicle. They can be used as a step to help you get in and out of your Wrangler, or as a place to mount other accessories, such as lights or a winch.

The RAMPAGE PRODUCTS 8827 are easy to install and come with all the necessary hardware. They are also backed by a limited lifetime warranty.

Here are some of the features and possible use cases for the RAMPAGE PRODUCTS 8827:

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents