Westinghouse T8 User manual

Category
Floodlights
Type
User manual

Westinghouse T8 LED replacement lamps are direct replacements for 32W T8 lamps, offering energy-efficient lighting with dimming capabilities when used with applicable ballasts. They operate on Instant Start Electronic Ballast only and are not compatible with preheat luminaires or emergency exit fixtures. Installation is simple, requiring the user to turn off power, remove the diffuser or lens cover, rotate and remove the fluorescent lamp, insert the Westinghouse LED lamp, rotate it 90 degrees, and restore power.

Westinghouse T8 LED replacement lamps are direct replacements for 32W T8 lamps, offering energy-efficient lighting with dimming capabilities when used with applicable ballasts. They operate on Instant Start Electronic Ballast only and are not compatible with preheat luminaires or emergency exit fixtures. Installation is simple, requiring the user to turn off power, remove the diffuser or lens cover, rotate and remove the fluorescent lamp, insert the Westinghouse LED lamp, rotate it 90 degrees, and restore power.

Westinghouse Lighting, Philadelphia, PA 19154-1029, U.S.A.
www.westinghouselighting.com
, WESTINGHOUSE, and INNOVATION YOU CAN BE SURE OF
are trademarks of Westinghouse Electric Corporation.
Used under license by Westinghouse Lighting.
All rights reserved.
Made in China
INSTALLATION GUIDE
Please read all information before installing the lamps and keep this sheet for future reference.
These lamps are direct replacements for 32W T8 lamps only.
Also dimmable when used with applicable ballast
Operates on Instant Start Electronic Ballast only.
Risk of Fire: Do not install this lamp in a preheat luminaire.
Risk of electronic shock - Use only in dry locations.
Any modications to this product will void the warranty.
This lamp may not be compatible with all ballasts, go to www.westinghouselighting.com for compatibility information.
IMPORTANT SAFETY INFORMATION:
CAUTION: If the lamp or luminaire exibits undesireable operation (buzzing, ickering etc.), immediately turn o power, remove lamp from
luminaire and contact us at www.westinghouselighting.com.
Risk of re. Do not install in a pre-heat luminaire.
This lamp only operates on electronic ballasts. If lamp does not light when the luminaire is energized, remove lamp from luminaire and contact us at
www.westinghouselighting.com or qualied electrician.
This device is not intended for use with emergency exit xtures or emergency exit lights.
Lamps must be operated within an ambient xture temperature of -22
o
F and 133
o
F to ensure ul compliance.
INSTALLATION INSTRUCTIONS
Turn o the power to the
luminaire before removing
the lamp.
STEP 1. STEP 2. STEP 3A. STEP 3B.
STEP 4A. STEP 4B. STEP 5. STEP 6.
Remove the diuser, lens
cover or louver (if provided).
Fluorescent lamps to be
replaced with Westinghouse
LED T8 lamps are shown
above.
Remove the uorescent lamp.
First, rotate the lamp 90’
degrees.
Then, remove the lamp from
the lampholder.
Insert the Westinghouse
LED replacement lamp.
Then, rotate the lamp 90’
degrees.
Make sure that the pins are
completely seated in the
lampholders. One LED
lamp for each uorescent
lamp removed.
Repeat steps 3 and 4 as
needed for additional lamps.
Replace the diuser, lens
cover or louver (if removed in
step 2).
Turn the power to the
luminaire back on.
  • Page 1 1

Westinghouse T8 User manual

Category
Floodlights
Type
User manual

Westinghouse T8 LED replacement lamps are direct replacements for 32W T8 lamps, offering energy-efficient lighting with dimming capabilities when used with applicable ballasts. They operate on Instant Start Electronic Ballast only and are not compatible with preheat luminaires or emergency exit fixtures. Installation is simple, requiring the user to turn off power, remove the diffuser or lens cover, rotate and remove the fluorescent lamp, insert the Westinghouse LED lamp, rotate it 90 degrees, and restore power.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI