2. Eaton
  3. Powerware 9125

Eaton Powerware 9125 Installation Instructions Manual

  • Hello! I am an AI chatbot trained to assist you with the Eaton Powerware 9125 Installation Instructions Manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
9125
INSTALLATION INSTRUCTIONS
Seismic Kit
For use with Two-in-One
2500–3000 VA Models
www.powerware.com
Powerware is a registered trademark of Powerware Corporation.
Copyright 2003 Powerware Corporation, Raleigh, NC, USA. All rights reserved. No part of this document
may be reproduced in any way without the express written approval of Powerware Corporation.
3
Powerware
®
9125 (2500–3000 VA) Seismic Kit Installation Instructions S Rev A www.powerware.com
Powerware 9125 (2500–3000 VA) Seismic Kit
The Powerware
R
9125 (2500–3000 VA) seismic kit is available in two
models: a four-unit model and a six -unit model. The four-unit model can
secure up to four UPS, battery, or PowerPass
R
Distribution Module (PDM)
cabinets; the six-unit model holds up to six cabinets. Both models include
spacers for any extra openings.
Four-Unit Model
(Shown with Spacer)
Six-Unit Model
(Shown with Spacer)
Figure 1. Seismic Kits
The seismic kit includes:
쑺 1 seismic base with casters
쑺 1 front strap
쑺 1 back strap with tabs
쑺 4 seismic base angles
쑺 4spacers
쑺 8M6´ 16 hex bolts
쑺 8M6lockwashers
쑺 24 M4 ´ 8 Phillips hex-head screws with lockwashers
쑺 6M4´ 10 Phillips hex-head screws with lockwashers
Powerware 9125 (2500–3000 VA) Seismic Kit
4
Powerware
®
9125 (2500–3000 VA) Seismic Kit Installation Instructions S Rev A www.powerware.com
The following steps explain how to install the seismic kit.
1. If you are bolting the cabinet to the floor, use the following drill
patterns to prepare the floor mounting holes.
60.85 cm
(23.96 in)
53.96 cm
(21.24 in)
48.00 cm
(18.90 in)
43.00 cm
(16.93 in)
Ø1.43 cm
(0.56 in)
Figure 2. Drill Pattern for the Four-Unit Model
Powerware 9125 (2500–3000 VA) Seismic Kit
5
Powerware
®
9125 (2500–3000 VA) Seismic Kit Installation Instructions S Rev A www.powerware.com
60.85 cm
(23.96 in)
53.96 cm
(21.24 in)
60.40 cm
(23.78 in)
65.41 cm
(25.75 in)
Ø1.43 cm
(0.56 in)
Figure 3. Drill Pattern for the Six-Unit Model
Powerware 9125 (2500–3000 VA) Seismic Kit
6
Powerware
®
9125 (2500–3000 VA) Seismic Kit Installation Instructions S Rev A www.powerware.com
2. Attach the front and back straps to the base using the supplied
M6 ´ 16 hex bolts and lockwashers (see Figure 4). Verify the
straps align with the front and b ack edges of the base.
NOTE For floor mounting, also attach the seismic base angles with the
front and back straps as shown in Figure 5.
NOTE The base casters are removeable. To mount the seismic kit flush
with the floor, remove the casters and secure the base angles using the
inside screw position.
Figure 4. Attaching the Straps
Figure 5. Seismic Base Angles for Floor Mounting
Powerware 9125 (2500–3000 VA) Seismic Kit
7
Powerware
®
9125 (2500–3000 VA) Seismic Kit Installation Instructions S Rev A www.powerware.com
3. On the back of each cabinet, remove the screw on the top left
corner and discard (see Figure 6).
Figure 6. Removing Cabinet Screws
4. Beginning with a middle position, slide each cabinet into place.
NOTE The PDM must be installed to the left of the UPS and the EBM(s)
must be installed to the right of the UPS.
Figure 7. Sliding in a Cabinet
Powerware 9125 (2500–3000 VA) Seismic Kit
8
Powerware
®
9125 (2500–3000 VA) Seismic Kit Installation Instructions S Rev A www.powerware.com
5. Attach the cabinet to the tab on the back strap by installing one
of the supplied M4 ´ 10 Phillips hex-head screws (see Figure 8).
Figure 8. Securing the Cabinet to the Back Strap
6. Fasten the top of the cabinet to the front strap with two of the
supplied M4 ´ 8 Phillips hex-head screws.
Figure 9. Securing the Front Strap
Powerware 9125 (2500–3000 VA) Seismic Kit
9
Powerware
®
9125 (2500–3000 VA) Seismic Kit Installation Instructions S Rev A www.powerware.com
7. Install the remaining cabinets, leaving any empty slots to the
outside position(s).
If there is an empty slot, install spacers to complete the seismic
kit. Attach the spacer to the front and back straps using the
supplied M4 ´ 8 Phillips hex-head screws.
Figure 10. Installing Spacers
8. Roll the loaded cabinet to its permanent location.
If you installed seismic base angles, secure the base to the floor
with earthquake bolts (not provided).
Figure 11. Floor Mounting
Powerware 9125 (2500–3000 VA) Seismic Kit
10
Powerware
®
9125 (2500–3000 VA) Seismic Kit Installation Instructions S Rev A www.powerware.com
/