Miller JA46 Owner's manual

Brand: Miller

Model: JA46

Category: Welding System

Type: Owner's manual

This manual is also suitable for

CS-3A

Miller JA46 is a spot control designed to add electronically timed spot welding and burnback capabilities to SWINGARC and 50 Series wire feeders. With the JA46, you can easily switch between spot and continuous welding modes, adjust spot time and burnback time, and take advantage of its compact size for easy mounting on top of your wire feeder or DVC. With its precise controls and user-friendly interface, the JA46 is an excellent choice for a wide range of welding applications.

cover 1/94 − ST-072 762-C PRINTED IN USA

Read and follow these instructions and all

safety blocks carefully.

Have only trained and qualified persons

install, operate, or service this unit.

Call your distributor if you do not understand

the directions.

Give this manual to the operator.

For help, call your distributor

or: MILLER Electric Mfg. Co., P.O. Box 1079,

Appleton, WI 54912 414-734-9821

OWNER’S

MANUAL

May 1994 Form: OM-1086A

Effective With Serial No. JA-46

CS-3A

OM-1086A − 5/94

TABLE OF CONTENTS

SECTION 1 − SAFETY PRECAUTIONS AND SIGNAL WORDS

1-1. General Information And Safety 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1-2. Safety Alert Symbol And Signal Words 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

SECTION 2 − SPECIFICATIONS

2-1. Description 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

SECTION 3 − INSTALLATION

3-1. Installation Of Spot Control 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3-2. Gas Connections To Wire Feeder 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3-3. Gun Connections To Wire Feeder 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3-4. Reconnection For Momentary Trigger Operation 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

SECTION 4 − OPERATOR CONTROLS

4-1. Spot-Continuous Switch 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4-2. Time Range Switch 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4-3. Spot Time Control 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4-4. Burnback Time Control 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

SECTION 5 − SEQUENCE OF OPERATION

5-1. Gas Metal Arc Welding (GMAW) 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5-2. Shutting Down 7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

SECTION 6 − MAINTENANCE & TROUBLESHOOTING

6-1. Routine Maintenance 7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6-2. Circuit Board Handling Precautions 7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6-3. Troubleshooting 8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

SECTION 7 − ELECTRICAL DIAGRAMS

Diagram 7-1. Circuit Diagram 9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Diagram 7-2. Wiring Diagram 10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

SECTION 8 − PARTS LIST

Figure 8-1. Main Assembly 12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

LIST OF CHARTS AND TABLES

Table 6-1. Maintenance Schedule 7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Table 6-2. Troubleshooting 8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

OM-1086 Page 1

SECTION 1 − SAFETY PRECAUTIONS AND SIGNAL WORDS

1-1. GENERAL INFORMATION AND SAFETY

A. General

Information presented in this manual and on various la-

bels, tags, and plates on the unit pertains to equipment

design, installation, operation, maintenance, and trou-

bleshooting which should be read, understood, and fol-

lowed for the safe and effective use of this equipment.

B. Safety

The installation, operation, maintenance, and trouble-

shooting of arc welding equipment requires practices

and procedures which ensure personal safety and the

safety of others. Therefore, this equipment is to be in-

stalled, operated, and maintained only by qualified per-

sons in accordance with this manual and all safety pre-

cautions listed in the Arc Welding Safety Precautions in

welding power source Owner’s Manual.

1-2. SAFETY ALERT SYMBOL AND SIGNAL

WORDS

This safety alert symbol is used with the signal

words WARNING and CAUTION to call atten-

tion to the safety statements.

WARNING statements identify procedures or

practices which must be followed to avoid seri-

ous personal injury or loss of life.

CAUTION statements identify procedures or

practices which must be followed to avoid minor

personal injury or damage to equipment.

IMPORTANT statements identify special instructions

necessary for the most efficient operation of this equip-

ment.

SECTION 2 − SPECIFICATIONS

10-1/2 in

(267 mm)

4 in

(102 mm)

11-3/8 in

(289 mm)

Ref. ST-072 762-C

Figure 2-1. Overall Dimensions

2-1. DESCRIPTION

The CS-3A spot control is designed to add electronically

timed spot welding and burnback capabilities to the

SWINGARC and 50 Series wire feeders. The burnback

capability of the CS-3A is available for both spot and

continuous welding.

The spot control operates on 24 VAC, 50/60 Hertz, and

draws 0.5 amperes.

OM-1086 Page 2

SECTION 3 − INSTALLATION

Spot Time

Control

Spot-Continuous

Switch

Time Range

Switch

Burnback

Time Control

To Trigger Receptacle

On Wire Feeder

To Gun Switch Plug

To Gas Control

Receptacle On Wire Feeder

To Plug From

Wrapper Slots (4)

ST-072 762-C

Gas Valve

Figure 3-1. CS-3A Connections And Controls

WARNING: ELECTRIC SHOCK can kill.

• Do not touch live electrical parts.

• Shut down wire feeder and welding power

source, and disconnect input power employ-

ing lockout/tagging procedures before in-

specting or installing.

Lockout/tagging procedures consist of padlock-

ing line disconnect switch in open position, re-

moving fuses from fuse box, or shutting off and

red-tagging circuit breaker or other disconnect-

ing device.

3-1. INSTALLATION OF SPOT CONTROL

(Figure 3-1)

The CS-3A spot control can be mounted on top of a wire

feeder or DVC, if applicable. To install spot control, pro-

ceed as follows:

1. Loosen the four wrapper screws on top of wire

feeder/DVC.

2. Place spot control on top of wire feeder/DVC with

control panels facing the same direction.

3. Position control so that wrapper slots correspond

to feeder/DVC control box screws.

4. Slide control down onto screws.

5. Tighten wrapper screws.

3-2. GAS CONNECTIONS TO WIRE FEEDER

(Figure 3-1, And Diagrams 3-1 Thru 3-5)

IMPORTANT: When using a dual wire feeder, spot ca-

pability may be added to either side. Trigger and gas/

water control connections must be made to the appro-

priate side.

1. Disconnect gas valve plug from appropriate gas

control receptacle on rear of wire feeder.

2. Connect gas valve plug to 6-socket female plug

from left side of spot control rear panel (see

Figure 3-1).

3. Connect 6-pin male plug from spot control to ap-

propriate gas control receptacle on wire feeder

(see Figure 3-1).

3-3. GUN CONNECTIONS TO WIRE FEEDER

(Figure 3-1, And Diagrams 3-1 Thru 3-5)

IMPORTANT: When using a dual wire feeder, spot ca-

pability may be added to either side. Trigger and gas/

water control connections must be made to the appro-

priate side.

IMPORTANT: Place Contactor Control switch on weld-

ing power source in the REMOTE position.

1. Connect 4-pin male plug on trigger cord of spot

control to TRIGGER receptacle on front of wire

feeder (see Figure 3-1). Rotate threaded collar

fully clockwise.

2. Connect 4-socket female plug on trigger cord of

spot control to gun switch plug (see Figure 3-1).

Rotate threaded collar fully clockwise.

IMPORTANT: If CS-3A is used with a DDSC control, the

CS-3A gun switch plug must be connected to the DDSC,

and the plug from the DDSC that normally connected to

the TRIGGER receptacle on the wire feeder must be

connected to the CS-3A trigger control plug.

OM-1086 Page 3

Wire Drive

Motor

Work

Trigger

Control Cord

Gas/Water

Control Cords

Wire Feeder

CS-3A

Control

Trigger Control

Interconnecting

Cord

115 Volts/Contactor

Control Cord

Welding

Power Source

ST-071 073-B

REAR VIEW

FRONT VIEW

Diagram 3-1. Connection Diagram For CS-3A Used On Single Wire Feeder

Welding

Power Source

Right Gun

Trigger Control

Cord

Wire Drive

Motor And

Drive Assembly

Work

Left Gun

Trigger Control

Cord*

Gas/Water

Control Cords

CS-3A

Control

Wire Feeder

Trigger Control

Interconnecting

Cord

115 Volts/Contactor

Control Cord

ST-071 074-B

*When using a Dual Wire Feeder, spot capability may be added to either side (left side illustrated). Trigger and gas/water control

connections must be made to appropriate side.

REAR VIEW

FRONT VIEW

Diagram 3-2. Connection Diagram For CS-3A Used On Dual Wire Feeder

OM-1086 Page 4

DDSC Control

Trigger connections when DDSC is not used.

*When using a Dual Digital Wire Feeder, spot capability may be added to either side (left side illustrated).

Trigger and gas/water control connections must be made to the appropriate side.

Left Gun

Trigger Control

Cord*

Trigger Control

Interconnecting

Cord

115 Volts/Contactor

Control Cord

Gas/Water

Control Cords

CS-3A Control

DVC Control

Dual Digital

Wire Feeder

Welding Power

Source

Wire Drive Motor

And Drive Assembly

Work

IMPORTANT: Interconnections of CS-3A

with welding power source, wire feeder,

DVC, and DDSC shown only. The DVC

Owner’s Manual shows remainder of the

connections.

ST-071 075-B

REAR VIEW

FRONT VIEW

Diagram 3-3. Connection Diagram For CS-3A Used On Dual Digital Wire Feeder

Ref. ST-092 390-B

*Current Relay − DVC MP Models Only.

Voltage

Sensing

Leads

Gas Valve

Interconnecting

Cord

Output Control

Cord

115 Volts/Contactor

Control Cord

Work

CS-3A Control

DVC Control

DDSC Control

Remote Voltage

Control Cord

Digital Wire

Feeder

Remote Wire

Speed Control Cord

Gas Valve

Trigger Control

Interconnecting

Cord

Wire Feeder

115 Volts/Contactor

Control Cord

Gas Control

Cord

Welding Power

Source

Gun Trigger

Cord

Wire Drive Motor

And Drive Assembly

Gun

Gun Trigger

Control Cord

REAR VIEW

FRONT VIEW

Diagram 3-4. Connection Diagram For CS-3A Used On DVC Control, DDSC Control

And Single Digital Wire Feeder

OM-1086 Page 5

Ref. ST-092 390-B

*Current Relay − DVC MP Models Only.

Voltage

Sensing

Leads

Gas Valve

Interconnecting

Cord

Output Control

Cord

115 Volts/Contactor

Control Cord

Work

CS-3A Control

DVC Control

DDSC Control

Remote Voltage

Control Cord

Digital Wire

Feeder

Remote Wire

Speed Control Cord

Gas Valve

Trigger Control

Interconnecting

Cords

Wire Feeder

115 Volts/Contactor

Control Cord

Gas Control

Cord

Welding Power

Source

Gun Trigger

Cord

Wire Drive Motor

And Drive Assembly

Gun

Trigger Hold

Control

REAR VIEW

FRONT VIEW

Diagram 3-5. Connection Diagram For CS-3A Used On Trigger Hold Control, DVC Control,

DDSC Control, And Single Digital Wire Feeder

3-4. RECONNECTION FOR MOMENTARY TRIG-

GER OPERATION

The CS-3A is factory wired to complete each timed weld

only if the gun switch is held closed throughout the spot

weld cycle. If the gun switch is released before the

SPOT TIME control times out, the spot weld will not be

completed.

The CS-3A can be wired to complete each timed weld

after a momentary closure of the gun switch. In this

case, the spot weld cycle ends only after the SPOT

TIME control times out. To wire CS-3A for momentary

trigger operation, proceed as follows:

WARNING: Read and follow safety informa-

tion at beginning of entire Section 3 before

proceeding.

1. Remove wrapper.

2. Locate unconnected end of lead 44 originating at

terminal B on terminal strip 1T.

3. With SPOT-CONTINUOUS switch S51 in the

CONTINUOUS position, connect friction connec-

tor on lead 44 to the normally-open terminal (the

only unused terminal) on S51.

4. Reinstall wrapper.

OM-1086 Page 6

SECTION 4 − OPERATOR CONTROLS

4-1. SPOT-CONTINUOUS SWITCH (Figure 3-1)

The SPOT-CONTINUOUS switch provides selection of

either a continuous weld or a timed weld operation.

Placing the SPOT-CONTINUOUS switch in the SPOT

position provides weld current for the time period set by

TIME RANGE switch and SPOT TIME control. The

SPOT TIME control begins to time out when the gun trig-

ger is closed.

Placing the SPOT-CONTINUOUS switch in the CON-

TINUOUS position provides weld current for as long as

the gun trigger is closed.

4-2. TIME RANGE SWITCH (Figure 3-1)

The TIME RANGE switch provides selection of the spot

weld time range. Placing the TIME RANGE switch in the

.2 to 2.5 SEC position provides .2 to 2.5 seconds of weld

time. Placing the TIME RANGE switch in the 2.5 to 5

SEC position provides 2.5 to 5 seconds of weld time.

4-3. SPOT TIME CONTROL (Figure 3-1)

The SPOT TIME control provides selection of spot weld

time within the time range selected. The scale surround-

ing the SPOT TIME control is calibrated in seconds and

provides a direct reading of spot time when the TIME

RANGE switch is in the .2 to 2.5 SEC position. Double

the scale to read spot time when the TIMER RANGE

switch is in the 2.5 to 5 SEC position.

Rotating SPOT TIME control clockwise increases spot

weld time.

4-4. BURNBACK TIME CONTROL (Figure 3-1)

The BURNBACK TIME control provides selection of the

time that weld current is present on the electrode wire

after wire has stopped feeding. By keeping weld current

present on the electrode wire, the wire burns away from

the workpiece and toward the contact tip.

If electrode wire sticks to workpiece, the BURNBACK

TIME control setting should be increased.

If electrode wire burns back into contact tip, the BURN-

BACK TIME control setting should be decreased.

The scale surrounding the BURNBACK TIME control is

calibrated in seconds. Burnback time ranges from 0

through .25 seconds.

SECTION 5 − SEQUENCE OF OPERATION

WARNING: ELECTRIC SHOCK can kill;

MOVING PARTS can cause serious injury;

IMPROPER AIRFLOW AND EXPOSURE TO

ENVIRONMENT can damage internal parts.

• Do not touch live electrical parts

• Keep all covers and panels in place while op-

erating.

Warranty is void if this control or the welding

power source is operated with any portion of the

outer enclosure removed.

ARC RAYS, SPARKS, AND HOT SURFACES

can burn eyes and skin; NOISE can damage

hearing.

• Wear correct eye, ear, and body protection.

FUMES AND GASES can seriously harm

your health.

• Keep your head out of the fumes.

• Ventilate to keep from breathing fumes and

gases.

• If ventilation is inadequate, use approved

breathing device.

WELDING WIRE can cause puncture

wounds.

• Do not point gun toward any part of the body,

any conductive surface, or other personnel.

HOT METAL, SPATTER, AND SLAG can

cause fire and burns.

• Watch for fire.

• Keep a fire extinguisher nearby, and know

how to use it.

• Do not use near flammable material.

• Allow work and equipment to cool before han-

dling.

MAGNETIC FIELDS FROM HIGH CURRENTS

can affect pacemaker operation.

• Wearers should consult their doctor before

going near arc welding, gouging, or spot

welding operations.

See Arc Welding Safety Precautions in welding

power source Owner’s Manual for basic welding

safety information.

5-1. GAS METAL ARC WELDING (GMAW)

WARNING: Read and follow safety informa-

tion at beginning of entire Section 5 before

proceeding.

1. Install and prepare welding power source accord-

ing to its Owner’s Manual.

2. Install Spot Control as instructed in Section 3.

3. Install and prepare wire feeder according to its

Owner’s Manual.

OM-1086 Page 7

4. Wear dry insulating gloves and clothing, and

wear welding helmet with proper filter lens ac-

cording to ANSI Z49.1

5. Prepare for welding as follows:

a. Connect work clamp to clean, bare metal at

workpiece.

b. Select and obtain proper welding wire, and

thread as instructed in wire feeder Owner’s

Manual.

IMPORTANT: Place Contactor Control switch on weld-

ing power source in the REMOTE position.

6. Energize welding power source and wire feeder.

Turn on shielding gas at its source.

7. Rotate BURNBACK TIME control to the desired

setting (see Section 4-4).

8. Place the SPOT-CONTINUOUS switch in the de-

sired position (see Section 4-1).

9. If the SPOT mode is being used:

a. Position TIME RANGE switch to time range de-

sired (see Section 4-2).

b. Rotate the SPOT TIME control to the desired

setting (see Section 4-3).

10. Make adjustments to wire feeder.

11. Depress gun trigger and begin welding.

IMPORTANT: The gun trigger must be held closed until

the SPOT TIME control has timed out thereby complet-

ing the spot weld cycle unless the unit was reconnected

for momentary operation (see Section 3-4).

5-2. SHUTTING DOWN

1. Stop welding.

2. Shut down welding power source and wire feed-

er.

3. Turn off shielding gas.

WARNING: HIGH CONCENTRATION OF

SHIELDING GAS can harm health or kill.

• Shut off gas supply when not in use.

SECTION 6 − MAINTENANCE & TROUBLESHOOTING

6-1. ROUTINE MAINTENANCE (Table 6-1)

IMPORTANT: Every six months inspect the labels on

this unit for legibility. All precautionary labels must be

maintained in a clearly readable state and replaced

when necessary. See Parts List for part number of pre-

cautionary labels.

WARNING: ELECTRIC SHOCK can kill.

• Do not touch live electrical parts.

• Shut down wire feeder and welding power

source, and disconnect input power employ-

ing lockout/tagging procedures before in-

specting, maintaining, or servicing.

Lockout/tagging procedures consist of padlock-

ing line disconnect switch in open position, re-

moving fuses from fuse box, or shutting off and

red-tagging circuit breaker or other disconnect-

ing device.

MOVING PARTS can cause serious injury.

• Keep away from moving parts.

HOT SURFACES can cause severe burns.

• Allow cooling period before servicing.

Troubleshooting to be performed only by quali-

fied persons.

Table 6-1. Maintenance Schedule

Frequency* Maintenance

Every month. Units in heavy service environ-

ments: Check labels and intercon-

necting cords.

Every 6 Months. Check all labels (see IMPORTANT

block, Section 6-1) and intercon-

necting cords.

*Frequency of service is based on units operated 40

hours per week. Increase frequency of maintenance if

usage exceeds 40 hours per week.

Every six months, inspect all interconnecting cords and

plugs for damage to the insulation jacket. Repair or re-

place cord(s) as necessary.

6-2. CIRCUIT BOARD HANDLING PRECAUTIONS

WARNING: ELECTRIC SHOCK can kill.

• Do not touch live electrical parts.

• Shut down wire feeder and welding power

source, and disconnect input power employ-

ing lockout/tagging procedures before in-

specting, maintaining, or servicing.

Lockout/tagging procedures consist of padlock-

ing line disconnect switch in open position, re-

moving fuses from fuse box, or shutting off and

red-tagging circuit breaker or other disconnect-

ing device.

OM-1086 Page 8

CAUTION: ELECTROSTATIC DISCHARGE

(ESD) can damage circuit boards.

• Put on properly grounded wrist strap BE-

FORE handling circuit boards.

• Transport circuit boards in proper static-

shielding carriers or packages.

• Perform work only at a static-safe work area.

INCORRECT INSTALLATION or misaligned

plugs can damage circuit board.

• Be sure that plugs are properly installed and

aligned.

EXCESSIVE PRESSURE can break circuit

board.

• Use only minimal pressure and gentle move-

ment when disconnecting or connecting

board plugs and removing or installing board.

6-3. TROUBLESHOOTING

WARNING: ELECTRIC SHOCK can kill.

• Do not touch live electrical parts.

• Shut down wire feeder and welding power

source, and disconnect input power employ-

ing lockout/tagging procedures before in-

specting, maintaining, or servicing.

Lockout/tagging procedures consist of padlock-

ing line disconnect switch in open position, re-

moving fuses from fuse box, or shutting off and

red-tagging circuit breaker or other disconnect-

ing device.

MOVING PARTS can cause serious injury.

• Keep away from moving parts.

HOT SURFACES can cause severe burns.

• Allow cooling period before servicing.

Troubleshooting to be performed only by quali-

fied persons.

It is assumed that the unit was properly installed accord-

ing to Section 3 of this manual, the operator is familiar

with the function of controls, the control and welding

power source were working properly, and that the

trouble is not related to the welding process.

The following table is designed to diagnose and provide

remedies for some of the troubles that may develop in

this spot control. Use this table in conjunction with the

circuit diagram while performing troubleshooting proce-

dures. If the trouble is not remedied after performing

these procedures, contact the nearest Factory Autho-

rized Service Station/Service Distributor. In all cases of

equipment malfunction, strictly follow the manufactur-

er’s procedures and instructions.

Table 6-2. Troubleshooting

TROUBLE PROBABLE CAUSE REMEDY

Wire feeder energizes but

will not feed.

Switch control plug PLG51 loose. Secure PLG51 in receptacle on control.

Gun switch. Replace gun switch.

Electrode wire feeds but is

not electrically hot.

Plug from welding power source contac-

tor control receptacle loose or loose

lead(s) in the plug or receptacle.

Secure plug in receptacle at control and

welding power source.

Be sure that the leads inside of receptacles

and plug are secured to their respective ter-

minals.

Extremely short or infinitely

long spot and/or burnback

time.

Printed circuit board. Replace printed circuit board located on bot-

tom right side of unit.

OM-1086 Page 9

SECTION 7 − ELECTRICAL DIAGRAMS

Circuit Diagram No. SB-072 114-C

Diagram 7-1. Circuit Diagram

OM-1086 Page 10

Diagram 7-2. Wiring Diagram

Wiring Diagram No. SC-153 933

OM-1086 Page 11

SECTION 8 − PARTS LIST

OM-1086 Page 12

SD-072 761-B

17 18 19

Figure 8-1. Main Assembly

OM-1086 Page 13

Part

No.

Dia.

Mkgs.

Figure 8-1. Main Assembly

Item

No. Description Quantity

1 048 848 SPRING, hold down relay 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2 CR52 080 388 RELAY, encl 24VAC 3PDT 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3 080 148 SOCKET, relay 11 pin 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4 048 725 BRACKET, mtg relay 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5 +049 173 WRAPPER 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6 134 327 LABEL, warning general precautionary 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

7 1,2T 038 042 STRIP, terminal 4P 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

8 010 476 BUSHING, strain relief .625 ID 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

9 604 571 CABLE, port No. 18 4/c (order by ft) 7ft. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

10 079 531 CLAMP, cable 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

11 PLG52 080 328 RECEPTACLE W/SOCKETS, free hanging (consisting of) 1. . . . . . . . . . . . . . . . . . . . . . .

079 534 TERMINAL, female 1skt 14-18W 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

12 PLG51 079 878 HOUSING PLUG & PINS, (consisting of) 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

079 535 TERMINAL, male 1 pin size 16 18-4 wire 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

13 010 217 BLANK, snap-in metal .625mtg 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

14 052 246 CABLE, pwr No. 20ga 5/c (order by ft) 5ft. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

15 PLG53 056 265 CONNECTOR, male 6cont 10A 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

16 PLG50 048 842 CONNECTOR, female 6skt w/cable clamps 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

17 031 251 BRACKET, mtg connector 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

18 RC52 073 730 TERMINAL, header 22 pin PC mtg 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

19 PLG54 079 798 HOUSING, terminal header 13 pin 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

20 084 440 CIRCUIT CARD ASSEMBLY, dual timer 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

21 010 301 BUSHING, al .140 ID x .250 OD 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

22 S50 011 609 SWITCH, tgl SPDT 15A 120V 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

23 R61,62 028 770 POTENTIOMETER, C sltd 1/2T 2W 1 meg ohm 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

24 NAMEPLATE, (order by model and style number) 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

25 097 922 KNOB, pointer 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

26 072 128 CASE SECTION 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

27 S51 011 611 SWITCH, tgl DPDT 15A 120V 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

057 359 BUSHING, snap-in nyl .375mtg hole 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

+When ordering a component originally displaying a precautionary label, the label should also be ordered.

BE SURE TO PROVIDE MODEL AND STYLE NUMBER WHEN ORDERING REPLACEMENT PARTS.