Cooper Lighting SP Splitter Installation guide

Risk of Fire and Electrical Shock- MWS must

be installed by qualified personnel. If not

qualified, consult an electrician.

Risk of Electric Shock- Disconnect power at

fuse or circuit breaker before installing or

servicing.

Ensure both latches are securely fastened-

Unlatched connections can separate causing

arcing and overheating of the connectors.

WARNING

IMPORTANT: Read, understand and follow all MWS

safety and installation instructions. Retain for future

reference.

NOTICE: Installation must comply with all applicable

national and local codes. Manufactured wiring systems

covered by Article 604 of the National Electrical Code.

NOTICE: Do not use any MWS component for other

than it’s intended purpose.

NOTICE: Do not tamper with the internal wiring of any

MWS component or physically modify in any way.

NOTICE: Starter fitting/starter fixture cable is

the starting point of the MWS system. All MWS

components attached to the system will be energized.

Cap all unused connector openings.

Installation Instructions – MWS

Instructions d’installation – MWS

Instrucciones de instalación del sistema de cableado modular

IMPORTANT: Save installation instructions for future changes.

ADM140814

MWS

Failure to comply with these instructions may result in death, serious bodily injury and property damage.

DISCLAIMER OF LIABILITY: Eaton assumes no liability for damages or losses of any kind that may arise from the

improper, careless, or negligent installation, handling or use of this product.

INSTALLATION

1. Standard carton size 14”W x 14”L x 12”H

Half carton size 14”W x 14”L x 6”H.

2. Each carton label list component cat. no. quantity,

length voltage with photograph.

3. Standard pallet size: 32”W x 46”L x 42”H

Max. 18 cartons per pallet. Pallets are shrink

wrapped by Cooper.

120V/277V/347V

Blue/Hot 3

Red/Hot 2

Black/Hot 1

White/Neutral

Green

10/2G

12/2G

10/3G

12/3G

208V/240V/480V

Blue/Hot 3

Red/Hot 2

Black/Hot 1

Blank

Green

10/2G

12/2G

10/3G

12/3G

5

4

3

2

1

5

4

3

2

1

5

4

3

2

1

5

4

3

2

1

ote:N 12/4G, 10/4G Available (4 Hots) Yellow Conductor

in Pin #2.

MWS Standard Contact Configuration

2

MWS Components

Fixture Cable

Starter Fitting/Starter Cable

Starter Fitting

Starter Cable

3/4 (19mm)

4-3/8”(112mm)

12 ST

12/2G

XX

12 120V

27 277V

34 347V

20 208V

24 240V

48 480V

12/2G

12/3G

12/4G

10/2G

10/3G

10/4G

For Starter Cable

add Length

Starter Fixture Cable

Extender Cables

Switch Drops

Splitters

CT Fitting

Tee Cord Drops TS

Drop Cord “DS”

Tee Cable Drop

4-3/8”(112mm)

3/4”(19mm)

1-7/8”

(47mm)

5/8”

(16mm)

12 FC 12/2G XX

Length

07

09

11

13

15

17

3/4 (19mm)

4-3/8”(112mm)

5/8”(16mm)

1-7/8”

(47mm)

4-3/8”(112mm)

3/4”(19mm)

12 SF 12/2G 09

1 2

27

34

09

15

2-1/4”(57mm)

5-5/16”(136mm)

2-1/4”(57mm)

1-13/16”(45mm)

12 SD SL XX

All Switch Drops #12

Conductors

2-1/4”(57mm)

1-13/16”(45mm)

5-5/16”(136mm)

2-1/4”(57mm)

12 SP 12/4

12/4

10/4

5-5/16”(136mm)

2-1/4”(57mm)

1-13/16”(45mm)

4-3/8”(112mm)

5/8”

(16mm)

1-7/8”

(47mm)

2-1/4”

(57mm)

5-5/16”(136mm)

4-3/8’’(112mm)

4-3/8”(112mm)

09 - 9ft

15 - 15ft

21 - 21ft

2-1/4”

(57mm)

EATON ADM140814 Installation instructions - MWS

Installation Instructions – MWS

3

Starter Fittings “ST”

Fixture Cable “FC”

Poke Home Connectors standard on all fixture cables – Starter Fixture Cables –

Fixture Fitting Maximum 3 leads per poke Home Connector.

Red

Black

White

Blue

Green

Green/Yelllow

120V/277V/347V

From Panel

Install in 1/2" KO

12/2G-10/2G

GRN-WH-BK

12/3G-10/3G

GRN-WH-BK-RD

12/4G-10/4G

GRN-WH-BK-RD-BU

Red

Black

Blue

Green

Yelllow

208V/240V/480V

From Panel

12/2G-10/2G

GRN-BK-RD

12/3G-10/3G

GRN-BK-RD-BU

12/4G-10/4G

GRN-BK-RD-BU-YW

Starter Cable “ST”

Lengths 9’ – 15’ – 21’

wire per Starter Fitting detail

(Starter Fitting)

Wiring to Starter Fittings or

cables to be 90°

Starter (ST)

Fixture Cable (FC)

Dust Cover

Fixture

Wiring

Quick

Connect

Wiring from

Panel or

Switch Box

T SO Cord Drop “TS”

All Extender Cable between fixtures must be supported first 12” and every 4-1/2’ thereafter.

Starter (ST)

Wiring from Lighting

Panel or Lighting

Controller

Drop SO Cord “DS”

Extender Cable (EC)

Extender Cable (EC) Extender Cable (EC)

T SO Cord (TS)

Ensure both Latches

are Securely Fastened.

T SO Cord (TS)

Extender Cable (EC)

Drop SO Cord (DS)

Circuit T (CT)

EATON ADM140814 Installation instructions - MWS

Installation Instructions – MWS

4

Starter Fixture Cable “SF”

SL - Single Level, DL - Dual Level, SE - Single Level w/EM

Wire fixture before placing in ceiling Grid.

T Cable “TC”

Fixture Fitting “FF”

Drop Cable “DC”

Alternative - Fixture Fitting “FF”

Switch Drop “SD”

With Fitting

Run 15' “SD”

from SW box to

first fixture.

With fixture cables

run switch drop from

switch box to above

ceiling

ot

e:

N Fixt

ure Cables, Fixture Fittings, Tee Cord Drops and Drop Cords may be

ordered factory attached by Cooper Lighting.

Starter Fixture Cable (SF)

Wire Leads Per

Starter Cable may

run down wall to

Switch Box

#12 Loads

Fixture Cable or

Extender to next Figure

Fixture Wiring

Starter (ST)

Extender Cable (EC)

Fixture Fitting (FF)

Fixture Wiring

Extender Cable (EC)

Switch Drop (SD)

Extender Cable (EC)

Fixture Cable (FC)

Single Level

Dual Level

Extender Cable (EC)

Switch Drop (SD)

Fixture Fitting (FF)

Extender Cable (EC)

Run switch Drop to first Fixture Fitting

120V/ 277V/ 347V

120V/ 277V/ 347V – 2 Circuit, 2 Neutral

208V/ 240V/ 480V

Ground

Neutral/WH

Hot 1/BK

Hot 2/RD

Hot 3/BU or ORG

Hot 2/RD

Hot 1/BK

Neutral/WH

Ground

16/2G

16/3G

16/4G

Ground

Neutral 1/NB

Hot 1/BK

Hot 2/RD

Neutral 2/ORG

Ground

Neutral 1/NB

Hot 1/BK

Hot 2/RD

Neutral 2/ORG

16/4G 2N

Ground

Hot 1/BK

Hot 2/RD

Hot 3/BU or ORG

Hot 4/YW or WH

16/2G 16/3G

16/4G

Ground

Hot 4/YW or WH

Hot 1/BK

Hot 2/RD

Hot 3/BU or ORG

EATON ADM140814 Installation instructions - MWS

Installation Instructions – MWS

Page is loading ...

Eaton

1121 Highway 74 South

Peachtree City, GA 30269

P: 770-486-4800

www.eaton.com/lighting

Canada Sales

5925 McLaughlin Road

Mississauga, Ontario L5R 1B8

P: 905-501-3000

F: 905-501-3172

Printed in USA

Imprimé aux États-Unis

Impreso en los EE. UU.

Publication No. ADM140814

August 13, 2019

Eaton is a registered trademark.

All trademarks are property

of their respective owners.

Eaton est une marque de commerce

déposée. Toutes les autres marques

de commerce sont la propriété de leur

propriétaire respectif.

Eaton es una marca comercial

registrada. Todas las marcas

comerciales son propiedad de sus

respectivos propietarios.

Product availability, specifications,

and compliances are subject to

change without notice

La disponibilité du produit, les

spécifications et les conformités

peuvent être modifiées sans préavis

La disponibilidad de productos, las

especificaciones y los cumplimientos

están sujetos a cambio sin previo aviso

Warranties and Limitation of Liability

Please refer to www.eaton.com/LightingWarrantyTerms for our terms and conditions.

Garanties et limitation de responsabilité

Veuillez consulter le site www.eaton.com/LightingWarrantyTerms pour obtenir les conditions générales.

Garantías y Limitación de Responsabilidad

Visite www.eaton.com/LightingWarrantyTerms para conocer nuestros términos y condiciones.

FCC Statement

Note: This equipment has been tested and found to comply with the

limits for a Class A digital device, pursuant to part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against

harmful interference when the equipment is operated in a commercial

environment. This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in accordance with

the instruction manual, may cause harmful interference to radio

communications. Operation of this equipment in a residential area

is likely to cause harmful interference in which case the user will be

required to correct the interference at his own expense.

Declaración de la FCC

Nota: Este equipo ha sido probado y cumple con los límites para un

dispositivo digital de Clase A, de conformidad con la parte 15 de las

Normas de la FCC. Estos límites están diseñados para proporcionar

una protección razonable contra interferencias perjudiciales cuando el

equipo se opera en un entorno comercial. Este equipo genera, utiliza y

puede emitir energía de radiofrecuencia y, si no se instala y utiliza de

acuerdo con el manual de instrucciones, puede causar interferencias

perjudiciales en las comunicaciones de radio. El funcionamiento

de este equipo en un área residencial puede causar interferencias

perjudiciales, en cuyo caso el usuario deberá corregir las interferencias

por su cuenta.

Cooper Lighting SP Splitter Installation guide

Cooper Lighting SP Splitter Installation guide

in other languages

Related papers

Other documents