Hotpoint NBXR333EG0WW Installation guide

Brand: Hotpoint

Model: NBXR333EG0WW

Type: Installation guide

Installation

Instructions

ElectricDryer

Questions on Installation? Call: 1-800-GECARES (US)

or Visit our Web site at: www.GEAppliances.com (US)

BEFOREYOU BEGIN

Read these instructions completely and carefully.

•IMPORTANT -Savetbese

instructions for local inspector's use.

•IMPORTANT - Observeall

governing codes and ordinances.

• Note to Installer - Be sure to leave these instructions with

the customer.

• Note to Customer - Keep these instructions with your Use

and Care Book for future reference.

• This dryer must be exhausted to the outdoors.

• Before tile old dryer is removed from service or discarded,

remove tile dryer door.

• Service information and the wiring diagram are located in

the control console.

• Do not allow children on or in tile appliance. Close

supervision of children is necessary when tile appliance is

used near children.

FORYOUR SAFETY:

WARNING

• Use only rigid metal or flexible metal 4-in. diameter

ductwork for exhausting to the outdoors. Never

use plastic or other combustible, easy-to-puncture ductwork.

• This appliance must be properly grounded and installed

as described in these instructions.

• Do not install or store appliance in an area where it

will be exposed to water and/or weather

• Install the dryer where the temperature is above 50°F

for satisfactory operation of the dryer control system.

NOTE: Installation and service of this dryer

requires basic mechanical and electrical skills.

It is your responsibility to contact a qualified

installer to make the electrical connections,

TOOLS YOU

WILL NEED

SLIPJOINTPLIERS

FLATBLADESCREWDRIVER

PHILLIPSSCREWDRIVER

MATERIALS YOU WILL NEED

4"DIA.METALDUCT

(RECOMMENDED) DUCT

CLAMPS(2)

4"SPRING

CLAMPS(2)

4"DIA.FLEXIBLEMETALDUCT

(IFNEEDED)

4"DIA.METAL

ELBOW

DUCTTAPE

EXHAUSTHOOD SAFETYGLASSES

_x_ 3/4"_RELIEF

GLOVES ULRECOGNIZED

DRYERPOWER

CORDKIT

(NOTPROVIDED

WITHDRYER)

ULRATED120/240V,30A

WITH3OR4PRONGS.

IDENTIFYTHEPLUGTYPE

ASPERTHEHOUSE

RECEPTACLEBEFORE

PURCHASINGLINECORD.

Step 1

Step 2

Step 3

Step 4

Step 5

Step 6

Step 7

Prepare the Area and Exhaust for Installation of

New Dryer (see section 1).

Check and Ensure the Existing External Exhaust is

Clean (see section 1) and Meets Attached Installation

Specifications (see section 3).

Remove the Foam Shipping Pads (see section 1).

Move the Dryer to the Desired Location.

Connect the Power Supply (see section 2).

Connect the External Exhaust (see section 4).

Level Your Dryer (see section 5).

Step 8

Step 9

Check the Operation of the Power Supply

and Venting,

Place the Owners Manual and the Installation

Instructions in a Location Where They Will Be

Noticed By the Owner.

For Alcove or Closet Installation, see section 6.

For Bathroom or Bedroom Installation, see section 7.

For Mobile or Manufactured Home see, section 8.

For side or bottom exhaust, see section 9.

Installation Instructions

Minimum Clearance Other Than Alcove or Closet Installation

Mininmm clearance to combustible surfaces and for air' opening are: 0 in, clearance both sides and 1 in. rear, Consideration

must be given to provide adequate clearance for installation and service,

[] PREPARING FOR INSTALLATION

OF NEW DRYER

EXTERNAL

DUCT

OPENING

DUCTTAPEOR

DUCTCLAMP

4" METALDUCT

DUCTTAPEOR

DUCTCLAMP

TIP: Install your dryer before installing your washer.

This will allow better access when installing dryer exhaust.

REMOVING LINT FROM WALL

EXHAUST OPENING

INTERNALDUCT

WALL

CHECKTHATEXHAUST

HOODDAMPEROPENS

ANDCLOSESFREELY.

TILTTHEDRYERSIDEWAYS

ANDREMOVETHEFOAM

SHIPPINGPADSBY

PULLINGATTHESIDES

ANDBREAKINGTHEM

AWAYFROMTHEDRYER

LEGS.BESURETO

REMOVEALLOFTHE

FOAMPIECESAROUND

THELEGS,

[] ELECTRICAL CONNECTION

INFORMATION

WARNING- TO REDUCE THE RISK OF

FIRE, ELECTRICAL SHOCK AND PERSONAL

INJURY:

DO NOT USE AN EXTENSION CORD OR AN

ADAPTER PLUG WITH THIS APPLIANCE.

Dryer must be electrically grounded in accordance with

local codes and ordinances, or in the absence of local

codes, in accordance with the NATIONAL ELECTRI-

CAL CODE, ANSI/NFPA NO. 70.

ELECTRICAL REQUIREMENTS

This dryer mnst be connected to an individual branch ei[euit,

protected by the required time-delay fllses or circuit breakers. A

four or three wire, single phase, 120/240V or 120/208V, 60Hz,

30 amp circuit is required.

If the electric supply does [lot meet the above specifications, then

call a licensed electrician.

GROUNDING INSTRUCTIONS

This dryer must be connected to a grounded metal, permanent

wiring system, or an equipment grounding conductor must be mn

with the circuit conductors and connected to tile equipment-

grounding terminal on the appliance.

CONNECTING DRYER USING 4-WIRE

CONNECTION (MUST BE USED FOR

MOBILE HOME INSTALLATION)

NOTES: Since January 1,1996, the National Electric code requires

thatthe new constructions utilize a 4-wire connection to

an electric dryer

-_WARNING:only a 4-conductor cord shall be used when the

appliance is installed in a location where grounding through the

neutral conductor is prohibited, Grounding through the neutral is

prohibited for the new branch-circuit installations, mobile homes,

recreational vehicles, and areas where local codes prohibit

groundingthrough the neutral conduction,

REMOVEGROUNDSTRAP

ANDDISCARD,KEEPGREEN HOT

GROUNDSCREW WIRE RELOCATEGREEN

GROUNDSCREW

HERE

GREENOR

Installation Instructions

1. Turn off the circuit hreaker (s) (30 amp) or remove the dryer's

circuit fllse at ttle electrical box.

2. Be sure ttle dwer cold is unphlgged from ttle wall receptacle.

3. Remove tile powei cord covel located at ttle lower back.

4. Remove and discard giound suap. Kee t) the green

ground screw for step 7.

5. Install 3/4 in. UL recognized stiain ielief to powei

cord entry hole. Bring power cord through strain relief_

6. Connect power cold as follows:

A. Connect the 2 hot lines to the outer screws of

tile terminal block (marked L1 and L2).

B. Connect tile neutral (white) line to the center of

tile temlinal block (marked N).

7. Attach giound wire of power cold with the gieen ground

screw (hole above shain relief bracket). Tighten all

terminal block screws (3) completely.

8. Properly secure power cold to strain lelief.

9. Reinstall the covel_

, WARNING: NEVER LEAVE THE

COVER OFF OF THE TERMINAL BLOCK•

CONNECTING DRYER USING 3-WIRE

CONNECTION

IFREQUIRED,BYLOCALCODE,

INSTALLEXTERNALGROUND

(NOTPROVIDED)TOGROUNDED

METAL,COLDWATERPIPE,OR GREEN GROUND

OTHERESTABLISHEDGROUNDGROUND ;TRAP

DETERMINEDBYAQUALIFIEDSCREW

ELECTRICIAN. HOT

WIRE

STRAINRELIEF

BRACKET

3/4",UL

RECOGNIZED

STRAINRELIEF

NEUTRAL

HOT

(White) WIRE

COVER

3#10AWGMINIMUMCOPPER

CONDUCTORSOR120/240V30APOWER

SUPPLYCORDKITMARKEDFORUSE

WITHDRYERS& PROVIDEDWITHCLOSED

LOOPORSPADETERMINALSWITH

UPTURNEDENDS(NOTSUPPLIED).

1. Turn off tile circuit breaker (s) (30 amp) or remove the dryer's

circuit fllse at the electrical box.

2. Be snle the dryer cold is unphlgged froin the wall.

3. Remove the powei cord cover located at the lower back.

4. Install 3/4 in. UL recognized strain lelief to power cold

enhy hole. Bnng powei cord thiough shain reliefl

5. Connect power cord as follows:

A. Connect the 2 hot lines to the outer screws of the

tenninal block (marked L1 and L2).

B. Connect tile neutral (white) line to the center of

tile temlinal block (marked N).

6. Be snle ground strap is connected to iletltlal (center)

terminal of block and to green glound screw on cabinet

real. Tighten all terminal block screws (3) completely.

7. Ploperly secure power cold to shain reliefl

8. Reinstall the covel.

, WARNING: NEVER LEAVE THE

COVER OFF OF THE TERMINAL BLOCK•

[] EXHAUST INFORMATION

_WARNING - USE ONLY METAL 4-IN. DUCT.

DO NOT USE DUCT LONGER THAN SPECIFIED

IN THE EXHAUST LENGTH TABLE.

Using exhaust longer than specified length will:

• Increase the drying times and the enelgy cost.

• Reduce tile dryer life.

• Accmnulate lint, cleating a potential fire hazard.

The correct exhaust installation is YOUR RESPONSIBILITY.

Problems due to incorrect installation are not covered

by the warranty.

Tile MAXIMUM ALLOWABLE length of the exhaust system

depends upon tile type of duct, mnrlber of turns, the type of

exhaust hood (wall cap), and all conditions noted below. Both

rigid and flexihle metal duct are shown in the table below.

EXHAUST LENGTH

RECOMMENDED MAXIMUM LENGTH

Exhaust Hood Types

Use only for short

run installations

4"DIA.

Recommended

4,,

No. of 90_ Rigid Flexible Rigid Flexible

Elbows Metal Metal Metal Metal

0 90 Feet 55 Feet 60 Feet 45 Feet

1 60 Feet 40 Feet 45 Feet 30 Feet

2 45 Feet 30 Feet 35 Feet 20 Feet

3 35 Feet 20 Feet 25 Feet 15 Feet

4 25 Feet 15 Feet 15 Feet 10 Feet

If using flexible metal duct, please refer to page 5.

EXHAUST SYSTEM CHECK LIST

HOOD OR WALLCAP

•Terminate in a manner to prevent bar'k drafts o1"entry of birds oi

other wildlife.

• Termination should present minimal resistance to tile exhaust air flow

and shouM requite little or no maintenance to prevent clogging.

• Never install a screen in or over tlle exhaust duct. This could cause lint build up.

• Wall caps must be installed at least 12 in. above ground level or ally other

obstruction with the opening pointed down.

• If roof vents or louvered plenums are used, they inust be equivalent to a

4-in. dampened wall cap in regard to resistance to air flow, prevention of

back drafts, and maintenance required to prevent clogging.

SEPARATION OF TURNS

For best performance, separate all turns by at least 4 ft. of straight duct,

including distance between last ttlrn and exhaust hood.

TURNS OTHER THAN 90°

• One turn of 45° or less may be ignored.

• Two 45 ° turns should be treated as one 90 ° turn.

• Eactl turn over 45 ° shouM be treated as one 90 ° turn.

SEALING OF JOINTS

• All joints shouM be tigtlt to avoid leaks. Tile male end of each section of

duct must point away from ttle dryer.

• Do not asselnble ttle ductwotk with fasteners that extend into tlle duct.

They will serve as a collection point for lint.

• Duct joints call be made air and moisture tight by wrapping the

overlapped joints with duct tape.

• Horizontal runs stlould slope down toward tile outdoors 1/2 inch per foot

INSULATION

Duct work that tuns ttltough an unheated area ot is near air conditioning

shoukt be insulated to reduce condensation and lint build-up.

Installation Instructions

[] EXHAUST CONNECTION

_WARNING - TO REDUCE THE RISK

OF FIRE OR PERSONAL INJURY:

• This dryer must be exhausted to the outdoors.

• Use only metal duct.

• Do not terminate exhaust in a chimney, any gas vent,

under an enclosed floor (crawl space), or into an mtic.

The accumulated lint could create a fire hazard.

• Provide an access for inspection and cleaning of the

exhaust system, especially at turns. Inspect and clean at

least once a year.

• Never terminate the exhaust into a common duct with a

kitchen exhaust. A combination of lint and grease could

create a fire hazard.

• Do not obstruct incoming or exhausted air.

THIS DRYER COMES READY FOR REAR

EXHAUSTING. IF SPACE IS LIMITED, USE

THE INSTRUCTIONS IN SECTION 9 TO

EXHAUST DIRECTLY FROM THE SIDES OR

BOTTOM OF THE CABINET,

STANDARD REAR EXHAUST

(Vented above floor level)

ELBOWHIGHLY

RECOMMENDED

ELBOWHIGHLY

_ RECOMMENDED

RECOMMENDED

CONFIGURATION

TO MINIMIZE

EXHAUST

BLOCKAGE.

NOTE: ELBOWS WILL PREVENT DUCT

KINKING AND COLLAPSING.

STANDARD REAR EXHAUST

(Vented at floor level)

FORSTRAIGHT

LINEINSTALLATION,

CONNECTTHE

DRYEREXHAUST

TOTHEEXTERNAL

EXHAUSTHOODUSIN(

DUCTTAPEORCLAMR

_' "*' (CORDNOTSUPPLIED

r'""-,. WITHDRYER)

CUTTHEMETALEXHAUST

DUCT(NOTSUPPLIED)TOTHE

PROPERLENGTH.

[] LEVELING AND STABILIZING

YOUR DRYER

STANDTHEDRYERUPRIGHTNEARTHEFINALLOCATIONANDADJUST

THE4LEVELINGLEG_ATTHECORNERS,TOENSURETHATTHEDRYER

ISLEVELFROMSIDETOSIDEANDFRONTTOREAR.

LEVEL

FRON_TO-BACK. LEVEL

SIDE-TO-SIDE.

4LEVELING

LEGS

NOTE:WESTRONGLYRECOMMENDSOLIDMETALEXHAUSTDUCTING.

HOWEVER,IFFLEXIBLEDUCTINGISUSEDITMUSTBEMETALNOTPLASTIC. 4

Installation Instructions, Indoor Exhausting

USING FLEXIBLE METAL DUCTS

If rigid all metal duct cannot be used, then flexible all metal ducting

can be used, but it will reduce the maximum recommended duct

length. In special installations when it is impossible to use only

metal ducting, then ULqisted clothes dryer flexible metal transition

duct may be used as transition venting between the dryer and wall

connection only. The use of this dncting will affect dry time.

If flexible transition duct is necessary, the following directions must

be followed.

• Use the Shortest Length Possible.

• Stretch the Duct to Its Maximum Length to avoid kinks.

• Do Not Crush or Collapse the Duct.

• Never Use Transition Duct Inside the Wall or

Inside the Dryer.

• Avoid Resting the Duct on Sharp Objects.

• Venting Must Conform to Local Building Codes.

ELBOWHIGHLY

RECOMMENDED

_OWS HIGHLY

DONOTUSE

EXCESSIVE

EXHAUST

)(

)

[] ALCOVE OR CLOSET INSTALLATION

• If your dryer is approved for installation in an alcove oi'

closet, it will be stated on a label on the dryer back.

• The dryer MUST be vented to the outdoors. See the

EXHAUST INFORMATION sections 3 & 4.

• Minimum clearance between dryer cabinet and adjacent

walls or other surfaces is:

0 in. either side

3 in. front and rear

• Minimum vertical space from floor to overhead cabinets,

ceiling, etc. is 52 in.

• Closet doors must be louvered or otherwise ventilated and

must contain a minimum of 60 sq. in. of open area equally

distributed. If the closet contains both a washer and a

dryer, doors must contain a minimum of 120 sq. in. of open

area equally distributed.

[] BATHROOM OR BEDROOM

INSTALLATION

• The dryer MUST be vented to tile outdoors. See

EXHAUST INFORMATION section 3 & 4.

• The installation must conform with local codes or, in tile

absence of local codes, with the NATIONAL ELECTRI-

CAL CODE, ANSI/NFPA NO. 70.

[] MOBILE OR MANUFACTURED

HOME INSTALLATION

• Installation must conform to the MANUFACTURED

HOME CONSTRUCTION & SAFETY STANDARD,

TITLE 24, PART 32-80 or, when such standard is not

applicable, with AMERICAN NATIONAL STANDARD

FOR MOBILE HOME, ANSI/NFPA NO. 50lB.

• Tile dryer MUST be vented to the outdoors with tile

termination securely fastened to tile mobile home

structure. (See EXHAUST INFORMATION

section 3 & 4.)

• Tile vent MUST NOT be terminated beneath a mobile or

manufactured home.

• The vent duct material MUST BE METAL.

• Do not use sheet metal screws or other fastening devices

which extend into tile interior of the exhaust vent.

• See section 2 for electrical connection information.

Installation Instructions

[] DRYER EXHAUST TO RIGHT, LEFT

OR BOTTOM CABINET

I1"=

I/AWARNING- BEFORE PERFORMING

THIS EXHAUST INSTALLATION, BE SURE

TO DISCONNECT THE DRYER FROM ITS

ELECTRICAL SUPPLY. PROTECT YOUR

HANDS AND ARMS FROM SHARP EDGES

WHEN WORKING INSIDE THE CABINET.

BE SURE TO WEAR GLOVES

REMOVE

SCREW

ANDSAVE.

REMOVE

DESIRED

KNOCKOUT

(ONEONLY),

Detach and remove the bottom, right or left side knockout

as desired. Remove the screw inside the dryer exhaust duct

and save. Pull the duct out of the dryer.

FIXINGHOLE

B A

I _ 9"

Cut the duct as shown and keep portion A.

TAB LOCATION

BENDTAB

UP45°

Through the rear opening, locate the tab in the middle of

the appliance base. Lift the tab to about 45 ° using a fiat

blade screwdriver.

ADDING NEW DUCT

FIXING

HOLE

PORTION"A"

RIGHTOR

LEFTSIDE

EXHAUST

Reconnect the cut portion (A) of the duct to the blower

housing. Make sure that the shortened duct is aligned with

the tab in the base. Use the screw saved previously to secure

the duct in place through the tab on the appliance base.

ADDING ELBOW AND DUCT FOR

EXHAUST TO LEFT OR RIGHT

SIDE OF CABINET

• Preassemble 4" elbow with 4" duct. Wrap duct tape

around joint.

Insert duct assembly, elbow first, through the side opening

and connect the elbow to the dryer internal duct.

CAUTION: Be sure not to pull or damage the

electrical wires inside the dryer

when inserting the duct.

EXHAUSTCAN

BEADDEDTO

LEFTORRIGHTSIDE

DUCT

TAPE

Apply duct tape as shown on the joint between the dryer

internal duct and the elbow.

DUCT

CAUTION:

Internal duct joints must be

secured with tape, otherwise

they may separate and cause

a safety hazard.

Installation Instructions

ADDING ELBOW FOR EXHAUST

THROUGH BOTTOM OF CABINET

• Insert the elbow through the rear opening and connect it to

the dryer internal ducL

• Apply duct tape on the joint between the dryer internal

duct and elbow, as shown on page 6_

CAUTION:

Internal duct joints must be secured with tape,

otherwise they may separate and cause a

safety hazard.

ADDING COVER PLATE TO REAR

OF CABINET (SIDES AND BOTTOM

EXHAUST)

Connect standard metal elbows and ducts to complete the

exhaust system. Cover back opening with a plate (Kit

WE 1M454) available from your local service provider_

Place dryer in final location.

- NEVER LEAVE THE BACK I

OPENING WITHOUT THE PLATL (_t WE1M454) I

IT0qCHANGING DIRECTION OF

DOOR OPENING

1. Open the door and remove the filler plugs opposite the

hinges. With the door completely open, remove the

bottom screws fi'om each hinge on the dryer face. Insert

these screws about half way into the TOP holes, for each

hinge on the opposite side (where you removed the filler

plugs). Apply firm pressure to get the screw started.

2. Loosen the top screws fi'om each hinge on the dryer face

half way. With one hand holding the top of the door and

the other hand holding the bottom, remove the door

from the dryer by lifting it UP and OUT.

3. Rotate the door 180 ° . Insert the door on the opposite side

of the opening by moving the door IN and DOWN

until the top hinge and the bottom hinge are resting on

the top screws inserted in step 1.

4. Remove the remaining screws from the side of the

opening from which the door was removed. With these

screws secure each hinge at the bottom. Tighten the two

top screws on each hinge. Reinsert the plastic plugs on

the side fi'om which the door was removed.

LOOSENTHETOP

REMOVETHE SCREWSFROM

BOTTOMSCREW EACHHINGEON

FROMEACHHINGE THEDRYERFACE

ONTHEDRYER HALFWAY.

MOVETHEDOORINAND

DOWNUNTILTHETOPHINGE

ANDTHEBOTTOMHINGEARE

RESTINGONTHETOPSCREWS

INSERTEDINSTEP1.

SECUREEACHHINGE

ATTHEBOTTOMAND

TIGHTENTHETWOTOP

SCREWSOFEACHHINGE,

TO REGISTER YOUR DRYER

CALL TOLL-FREE

1-888-269-1192

Promptregistrationconfirmsyour rightto protectionunderthe

termsof yourwarranty.

www.GEAppliances.com (US)

For Questions on Installation, Call: 1-800-626-2003 (US)

500A1871 054 2 O1ON Pub # 31 1(;135

[] SERVICING

WARNING- LABEL ALL WIRES

PRIOR TO DISCONNECTING WHEN

SERVICING CONTROLS. WIRING

ERRORS CAN CAUSE IMPROPER AND

DANGEROUS OPERATION AFTER

SERVICING/IN STALLATION.

For servicing phone numbers for replacement parts, and

other information, refer to Owner's Manual or visit our

Web site.

Notes

Hotpoint NBXR333EG0WW Installation guide

Hotpoint NBXR333EG0WW Installation guide

Hotpoint NBXR333EG0WW Installation guide

Related papers

Other documents