Maytag Washer/Dryer User manual

Brand: Maytag

Model: Washer/Dryer

Category: Networking

Type: User manual

This manual is also suitable for

6 2708140-0498

Maytag Washer/Dryer: Tackle laundry like a pro with innovative features designed to deliver exceptional cleaning and drying performance. Experience efficient wash cycles that optimize water and energy usage, ensuring gentle care for your fabrics. Enjoy a range of drying options to suit different needs, from regular drying to delicate cycles for your most delicate garments.

NIAYI'AG STACKED WASHER/DRYER

_,o INSTALLATION INSTRUCTIONS

The installation, including a proper exhaust system, is the responsibility of the owner.

LEAVE THESEINSTRUCTIONSWITHTHE OWNER

Printedin U.S.A. 6 2708140-0498

Read this before you start...

TOOLS needed for installation

• Teflontape or pipejoint • Level

compound (gas) • Screwdriver (standard)

• Cutting knife • Ducttape

• Pipewrench(gas) • Crescentwrench

• Ratchet • 3/8" deepwell socket

___,(_)_1 • 5/16" socket (electric- U.S. only)

• 5/16" nutdriver

Electric Washer/Dryer Only Gas Washer/Dryer Only

ITEMS PROVIDED 0

Makesure you have everythingnecessaryfor properinstallation.

1. GROUNDEDELECTRICALOUTLET isrequired. SeeElectrical Requirementsstartingon page 6.

2. POWERCORDSfor electricdryers (exceptCanada).

3. GASLINES (if a gas dryer) must meet Nationaland LocalCodes.

4. EXHAUSTSYSTEM- use rigid metalor flexiblemetalexhaust ducting. See Exhaust Requirementsin

this section.

5. UTILITIESSHUTOFFS (electric,gas andwater) mustbe accessibleafterinstallation.

NOTE: Dryerdoor reversalinstructionsare on page 23 items 58 and 59.

27V2"

I, 69.9 cm • I

27"

Location Location

of Canadian of Canadian

terminal terminal

block

(electric 1 _8,:_,._

models) .v _,.,} Dryer

_5/16" _cationo yer terminal I,

2.4 block on electric models _' ___L- 3/4"

and power supply cord _ I-tl.9 cm

Connection on gas moaeJs _,'_

Gas Manifold (except Canadian)

--,. . 1_18"

711/2" 2.9 cm

81.6 cm

3/8"rain. Washer

395/32" .95 cm

washer water I 27_/2"

washer drain hose valve connections 69.9 cm

Page 1

Exhaust Hood Type

90° Turns

4" 2-1/2"

Maximumlength of 4-inchdiameter

rigid metalduct

0 65 ft. 59 ft.

1 54 ft. 48 ft.

2 44 ft. 38 ft,

3 36 ft. 30 ft.

4 28 ft. 22 ft.

Maximumlengthof 4-inchdiameter

flexiblestiff wailedmetalduct

0 36 ft. 28 ft.

1 32ft. 24ft.

2 28ft. 20ft.

3 25 ft. 17ft.

4 23ft. 15ft.

Fordifficultinstallationsrequiringa flexibletransition, multi-layeredthinfoil exhaust ductmaybe used.

Thinfoilduct:

• mustbe the typethat isapproved for dryer installationsby ULor other comparabletesting agency.

• mustconformto allapplicablecodes.

• mustonly be usedas atransition betweenthe dryer and the wallconnection.

• mustnot exceed8 feet in lengthwhen stretched.

• mustnot interconnectwithotherthin foil flexibleducts.

• mustbe extendedto the full lengthwith any excessremoved.

• mustbe installedonly by a qualifiedand trained installer,

• mustnot be placed nearsharpobjects.

• mustbe keptas straightas possible.

• mustnot be usedinsidethe dryer.

• mustbe inspectedregularlyto be surethat it hasnot becomecrushedor otherwiserestricted.

Thinfoil ductwill reduceairflowresultingin longer dryingtimes. Toreducethe negativeeffecton drying

performancethe thin foilducting:

• shouldbe shapedsuch that thereare no morethan two 90-degreeelbowsin the foil duct.

• shouldnot be usedin conjunctionwith rigid duct runsthat are longerthan 20 feet.

• shouldnot be usedin ductrunsthat includemorethanthree90-degreeelbows.

• shouldbe supportedto minimizesagging.

Seriousblockagecan resultin flexible metalduct if benttoo sharp. Neverinstall anytype of ducting in walls,

ceilings,or otherconcealedspaces.

Keepexhaustduct as straightandshort as possible. Exhaust systemslonger than recommendedcan extend

dryingtimes,affectmachine operationand maycollect lint. Securejoints with duct tape.

Donot usescrews.

Page 3

Exhaust Hood Type

90° Turns

4" 2-1/2"

Maximumlength of 4-inchdiameter

rigid metalduct

0 65 ft. 59 ft.

1 54 ft. 48 ft.

2 44 ft. 38 ft,

3 36 ft. 30 ft.

4 28 ft. 22 ft.

Maximumlengthof 4-inchdiameter

flexiblestiff wailedmetalduct

0 36 ft. 28 ft.

1 32ft. 24ft.

2 28ft. 20ft.

3 25 ft. 17ft.

4 23ft. 15ft.

Fordifficultinstallationsrequiringa flexibletransition, multi-layeredthinfoil exhaust ductmaybe used.

Thinfoilduct:

• mustbe the typethat isapproved for dryer installationsby ULor other comparabletesting agency.

• mustconformto allapplicablecodes.

• mustonly be usedas atransition betweenthe dryer and the wallconnection.

• mustnot exceed8 feet in lengthwhen stretched.

• mustnot interconnectwithotherthin foil flexibleducts.

• mustbe extendedto the full lengthwith any excessremoved.

• mustbe installedonly by a qualifiedand trained installer,

• mustnot be placed nearsharpobjects.

• mustbe keptas straightas possible.

• mustnot be usedinsidethe dryer.

• mustbe inspectedregularlyto be surethat it has not becomecrushedor otherwiserestricted.

Thinfoil ductwill reduceairflowresultingin longer dryingtimes. Toreducethe negativeeffecton drying

performancethe thin foilducting:

• shouldbe shapedsuch that thereare no morethan two 90-degreeelbowsin the foil duct.

• shouldnot be usedin conjunctionwith rigid duct runsthat are longerthan 20 feet.

• shouldnot be usedin ductrunsthat includemorethanthree90-degreeelbows.

• shouldbe supportedto minimizesagging.

Seriousblockagecan resultin flexible metalduct if benttoo sharp. Neverinstall anytype of ducting in walls,

ceilings,or otherconcealedspaces.

Keepexhaustduct as straightandshort as possible. Exhaust systemslonger than recommendedcan extend

dryingtimes,affectmachine operationand maycollect lint. Securejoints with duct tape.

Donot usescrews.

Page 3

DONOT exhaustdryer into any wall, ceiling, crawl spaceor a concealedspace of a building,gas vent,

or anyother common ductor chimney. This could createa fire hazardfrom lint expelledbythe dryer.

The exhaustductshould end withan exhaust hoodwith a swingout damperto prevent backdraftsand entry

of wildlife. NEVERuse an exhausthood with a magneticdamper. The hood should haveat least 12inches

of clearancebetweenthe bottom of the hood andthe groundor otherobstruction. The hoodopeningshould

pointdown. NEVERinstall a screenoverthe exhaustoutlet.

Whenpossible,do notexhaust the dryer directlyinto a windowwell in orderto avoid lint build-up. Do not

exhaustundera houseor porch.

If exhaustductworkmustrunthrough an unheatedarea,the duct shouldbe insulatedand slope slightlydown

towardsthe exhaust hoodto reducecondensationand lint build-up.

If an existingexhaust systemis to be used withyour dryer(s) you must besure:

• The exhaustsystemmeetsall local,stateand nationalcodes.

• That plasticflexibleduct is not used.

• Tocompletelyinspectand cleanall lint accumulatingfrom the interiorof the duct.

• The ductis not kinkedor crushed.

• The exhaust hooddamperopens andcloses freely.

Inspectand cleanthe interiorof the exhaust systemat leasttwice a year. Disconnectelectricservice priorto

cleaning. Check gasline on gasdryers anytimethe dryer is moved.

Frequentlycheckto be sure the exhaust hooddamper opensand closesfreely.

WASHER REQUIREMENTS

Waterpressureof 20to 120 p.s.i,is requiredto correctlyfill the washerto the proper levels.

DRAIN FACILITY

Recommendedheightof the stand pipe is 36 inches. Ifthe stand pipeis less than 36 incheshigh,the drain

hoseshould be routedthroughthe clipto raisethe hoseto the proper height. Stand pipe mustbe large

enoughto acceptthe outsidediameterof the drain hose.

Without the 36 inches high elevation, water may run out of the washer prematurely. Shouldthe washer

fill and drain atthe sametime could indicatethat the drain hosehas notbeen elevatedto the proper height.

Thedrain hoseis attachedat the factory.

FLOORING

For bestperformancethe washer mustbe installedon a solidly constructedfloor. Woodfloors mayneedto

be reinforcedto minimizevibration and/or unbalancedload situations. Carpeting and softtile surfaces are

contributingfactorsin vibration and/ortendency for awasher to moveslightly during the spin cycle. Never

installthe washer on a platform or weak supportedstructure.

LOCATION CONSIDERATIONS

It is recommendedthe washer never be installedin areaswherewater mayfreeze since the washer will

always maintainsome waterin the water valve, pump and hoseareas. This can cause damageto belts,

pump, hosesand othercomponents. Operatingtemperatureshould be above60°F.

Page4

GAS REQUIREMENTS

Useonly Naturalor LP (liquidpropane)gases.

THE INSTALLATIONMUSTCONFORMWITHLOCALCODES,OR IN THEABSENCEOF LOCALCODES,

WITHTHE NATIONALFUELGAS CODEANSI/Z223.1,LATESTREVISION(FORTHE UNITEDSTATES),

OR WITHTHE CAN/CGA-B149INSTALLATIONCODES(FOR CANADA).

A gas dryer is equippedwith a burner orifice foroperationon NATURALgas. If the dryer is to be operated

on LPgas, it mustbe convertedfor safe and proper performanceand mustbe converted by a

qualifiedservice technician. Conversionkits from NATURALto LP,or LP to NATURALareavailable

through your localdealer (seeAccessories). Ifother conversionsarerequired,checkwith the localgas utility

for specific informationconcerningconversionrequirements.

Eachdryerwill providean input of 22,000 B.T.U.per hour.

A 1/2inchgas supplylineis recommendedand mustbe reducedto connectto the 3/8 inchgasline onthe

dryer.

The internalgas shut-offisaccessedby removingthe accesspanelon the dryer. The shut-offispositioned

for easy accessnearthe gas valve.

The NationalFuelGas Code requiresthat an accessible,approvedmanualgasshut offvalve be installed

within 6feet of the dryer.

Additionally,a 1/8 inch N.P.T.(NationalPipeThread) pluggedtapping, accessiblefor test gaugeconnection,

mustbe installedimmediatelyupstreamof the gas supplyconnectionto the dryer.

Thedryermustbe disconnectedfromthegas supplypipingsystemduringanypressuretestingofthesystem.

DO NOT re-useold flexible metalgasline. Flexiblegasline mustbe design certifiedbyAmericanGas

Association(CGAin Canada). NOTE: Any pipejoint compoundusedmustbe resistantto the actionof any

liquefiedpetroleumgas.

NOTE: Asa courtesy,mostlocal gas utilitieswill inspecta gas applianceinstallation.

GAS IGNITION -

Thedryeruse anautomaticignitionsystemto ignitethe burner. There is no constant burning pilot.

GROUNDING

• Improperconnectionof the equipment-groundingconductorcan resultin a riskof

electricalshock. Checkwith a qualifiedelectricianor servicemanif you arein

I 1_0 I doubtas to whetherthe applianceis properlygrounded.

• Do not modifythe plug providedwith the appliance- if it will not fitthe outlet,

havea properoutletinstalledby a qualifiedelectrician.

• Toprevent unnecessaryriskof fire, electricalshock or personalinjury,all wiring

and groundingmust be done in accordancewith the NationalElectricalCode

ANSI/NFPA,No.70-Latest Revision(for U.S.)or the CanadianElectricalcode

CSAC22.1-LatestRevision(for Canada)and localcodes and ordinances. It is

the personalresponsibilityand obligationof the applianceowner to provideadequateelectrical services

forthis appliance.

• All gas installationsmustbe donein accordancewiththe NationalFuelGas CodeANSI/Z223.1-Latest

Revision(forthe U.S.)or the CAN/CGA-B149InstallationCodes-LatestRevision(forCanada)and local

codesand ordinances.

Page 5

ELECTRICAL REQUIREMENTS WARNING- TOprevent

unnecessaryrisk of fire,

NOTE: Wiring diagram is located inside the access panel, electricalshock or

personalinjury,all wiring

Export models (not U.S. or Canada): and grounding must be

See AdditionalInstructionsfor Export Modelson the following done in accordance

pages, with local codes, with

the National Electrical Code,

GROUNDING ANSl/NFPA(for the United States)

or the Canadian Electrical Code

Eachdryer mustbe grounded. Inthe eventof malfunctionor CSAC22.1 (for Canada).

breakdown,the groundwill reducethe risk of electricalshockby

providing a pathof leastresistancefor electricalcurrent.

GAS MODELS _

Eachapplianceisequippedwitha cordhavinganequipment-grounding

conductoranda groundingplug. Theplugmustbe pluggedintoan

appropriateoutletthatisproperlyinstalledandgroundedinaccordance

withalllocalcodesandordinances.

Do notmodifythe plugprovidedwiththeappliance- if it will not fit the

outlet,have a proper outletinstalledby a qualifiedelectrician.

If a separateground isrequiredby local codes,anaccessorygroundwireand groundclamp isavailable. Con-

nectgroundwire to backof unitwiththecabinetgroundscrew and washertheground screwand washerar

foundinthe partspackage. Secureotherend of groundwire to a suitableexternalgroundconnection. The

wire maybe securedwith the clampto a groundedCOLDmetalwater pipe. NEVERCONNECTGROUND

WIRETO PLASTICPLUMBINGLINES,GAS LINESOR HOTWATERPIPES.

ELECTRIC MODELS

If a powercordis notusedandtheelectricdryeristo be perma-

nentlywired,thedryermustbeconnectedto a groundedmetal, WARNING: Improper

permanentwiringsystem;or an equipmentgroundingconductor connectionof the

mustbe runwiththe circuitconductorsandconnectedto the equipmentgrounding

equipmentgroundingterminal, conductorcan resultin

a riskof electricshock.

U.S.Electricmodelsareshippedwith a groundstrap connected

fromthe neutralterminalblockpostto theframeof eachdryer. If Checkwith a qualified

localcodesprohibitsthe use ofthe groundstrap,the dryermustbe electricianor servicemanif youare in

groundedinaccordancewith localcodes, doubt asto whetherthe applianceis

properlygrounded.

Eachelectricdryermustbe connectedto a groundedmetal,

permanentwiringsystem;or an equipmentgroundingconductor

mustbe runwith the circuitconductorsand connectedtothe

equipmentgroundingterminal.

ELECTRICALCONNECTIONS

BEFOREOPERATINGOR TESTING,follow all groundinginstructionsin GroundingSectionabove.

An individualbranch(or separate)circuit servingonly thisapplianceis recommended. DO NOT USEAN

EXTENSIONCORD.

GAS MODELS - U.S. and Canada

A 120volt,60 HzAC,approvedelectricalsupply,witha 15amperefuseor circuitbreakerisrequired.

Page 6

ELECTRIC MODELS - U.S. and Canada

A 120/240volt, 60 HzAC approvedelectricalservicefusedthrougha 30amperefuse or circuitbreakeronboth

sidesofthe lineisrequiredforthe dryeranda 120volt60 HzACapprovedelectricalsupplywith a 15ampere

fuseorcircuitbreakerforthe washer.

Ifa powercord is used,the cord should be pluggedinto a 30 ampere receptacle.

U.S. ELECTRIC MODELS

The powercord is NOTprovidedwith U.S. electricmodeldryers.

IMPORTANT: Whenpermittedby localcodes, the dryerelectrical supply may be connectedby meansof a

newpowersupplycord kit, markedfor usewith clothesdryer,that is U.L.listed, ratedat 120/240volts

minimum,30 ampereswiththree No. 10copperwire conductorsterminatedwith closedloopterminals,

open-endspadelugs with turnedup ends orwith tinned leads.

Donot reusea powersupplycordfrom an olddryer. The powercord electricsupplywiring mustbe retained

at the dryercabinet with a suitableULlistedstrain relief.

Ifthe dryer isto be installedin an areawhere local codesdo not permitgroundingthrough neutral,onlya 4

conductorpowercord, ratedand terminatedas above,maybe used.

120/208Volt Electrical Systems:

A U.S.electricwasher/dryermustbe convertedif it isto operateon a 120/208volt electricalsystem. A heating

elementconversionkitis availablefor the dryeralongwith a transformerforthe washer (seeAccessories).

CANADIAN ELECTRIC MODELS

All Canadian models are shipped with the power cord attached.

It is not permissible to convert a dryer in Canada to 208 volts,

Additional Instructions for Export Models

(not U.S. or Canada)

Contactthe distributorthat sold the applianceor: Maytag International,8700W. Bryn MawrAvenue,Chicago,

IllinoisUSA 60631,773-714-0100, for informationon product,shippingdamage,replacementpartsand

accessories.

Maytagmodels manufacturedfor operationon 60 HzAC are not designedfor useon 50 HzAC

electricalserviceand conversionof the productfrom 60to 50 Hz operationis not recommended. For

additionalinformationon 50 Hz products,contact Maytag International.

The electricservicerequirementscan befound on the data labellocated onthe frontof the dryer behindthe

door.

EXPORT ELECTRIC MODELS

Exportelectric modelsare manufacturedfor operationon either 230/240volt, 50 Hzor 220 volt, 60 Hz

approvedelectricservice. A two-wireapprovedelectricalservicewith a30 amperefuseor circuitbreakeris

required. The dryermust be properlygroundedwitha groundwire.

IMPORTANT:When permittedbylocal codes,the dryer electricalsupply may be connectedby meansof a

newpowersupplycord kit, markedfor usewith clothesdryers, that is agencylisted, ratedat 240 volts

minimum,30 ampereswith two No. 10copper wire conductorsterminatedwith closed loopterminals,

open-endspadelugs with turnedup ends orwith tinned leads.

Donot reusea powersupplycordfrom an old dryer. The powercord or electricsupplywiring mustbe

retainedat the dryercabinetwith a suitableagencylistedstrain relief.

Page7

ADDITIONALINFORMATION

REPLACEMENT PARTS AND ACCESSORIES

Ifthe dryer requiresreplacementpartsor accessories,contact your local Maytagdealer fromwhom you

purchasedyourapplianceor:

MaytagCustomerService

240 EdwardsStreet, S.E.

Cleveland,Tennessee 37311

Phone615-472-3333,for informationon the nearestauthorizedMaytag PartsDistributor.

EXPORT MODELS

Contactthe CommercialDistributorfromwhom you purchasedyour applianceor:

MaytagInternational

8700 W. Bryn MawrAvenue

Chicago, Illinois,USA 60631

Phone312-714-0100,for informationon the nearestauthorizedMaytagParts Distributor.

Page 8

To install...

1•Carefullyremoveany packagingmaterialsfrom the outsideof the

washer. Set asidetwo cornerpostsfor installation. IMPORTANT:

Noticethat the hoses and powercord aretied upwith a shipping

strap. Thestrap should not be cut or removed untilthe machine

is readyto be installed.

Figure 1

2. Laytwo cornerposts behindthe washer and _ ___ -•

gentlytip the washerover on to itsback. 4L_____j..jiI if///

3. Usinga screwdriver,pry off the crate bottom

wire retainers(2) and removethe crate bottom

fromthe washer.

Figure2 Figure3

4. Locatetwo 1/2inch hexshippingbolts on bottomof

metalbase. Removeboth bolts, freeingthe tub and Shipping __

suspension. DO NOTBEALARMEDas the lastbolt Bolts

is removed,the tub will jump to a positionwhere it is _

restingagainstthe back of the washer.

Figure4 __'_

5. Loosenthe four adjustablewasher legs and lock nuts. Install

vinyl feetfound in installationpackage. Feetcan be more _--'---

easily installedwhen immersedin hotwater beforeinstalling.

Carefullyraisethe washer backto an uprightposition.

6. At the installationsite, locatethe metalbucklesattachedto

the shippingstraps at backof washer. Carefullycut away

strapsnear both buckles,completely removingboth

bucklesfromthe washer.

Pull loosestraps

from backof washer

oneat a time until

all strapshave been

Figure6 Figure7 removed.

Insertinlet hosescreensin the endsof the hot and cold inlethoses. Screensare found in the

miscellaneouspartspackage. Domedsurface isto facethe valve.

Page9

7, Openthe washerdoor 90degrees. Removethe tape holding the accesscover. (Seefigure 8.)

Removethe accesscover by slidingforward. DO NOTpull up. (Seefigure 9.)

Figure8 Figure9

8, Openthe AccessoryCartonand removethe access panel. Discardshipping materials. Gas dryers

includea gaspipe assemblyin the carton. (Seefigures 10& 11.)

Figure 10 Figure11

For Gas Dryers: Removered and blue threadprotectorsfromgas pipe. Knockout squarehole in rear of

supportand insertgas pipe throughhole. (See figures 12a-d.) Allow pipeto rest on inside

of support. (See figure 13.) Makesurevalve is closed. (Seefigure 13a.)

Page 10

Figure 12a Figure 12b

Figure12c Figure12d

Figure13 Figure13a

Page 11

9. For nonalcove installations, utilities and

venting can be connected after units are

stacked.

For alcoveinstallations:

Securetheexhaustbrackettothe rearofthe

washerwith screwsprovided.

(Seefigures14,15& 16.)

Unsnaphosesfromplastichosecaddy,leaving

caddyattachedto thebackofthe cabinet.

Connectfillhosestofaucets(hotwaterhoseis

the left hoseas youstandfacingthefrontofthe

washer). Insertthe drainhosein thestandpipe

recommendedheightof36 inches,minimumof

24inches. Note: Ifdrainhoseisnotsecurein

thestandpipe,usea portionofthe shipping

strapto securethedrainhoseto thestandpipe. Figure 14

Makesurethatdrainhoseissecuredto the hose

caddyafterinstallation.Fillhosesarenot to

besecuredtocaddy. Turnonwaterand checkfor leaks.

Moveunitintoposition,levelandtightenthe levelinglocknutsonthe legs. Securethe ventpipeto the

exhaustbracket. (See figure 16.) MAKINGSUREFIRSTTHATOUTLETISNOTENERGIZED,plug

washerintooutlet.

Figure15 Figure 16

Page 12

For gasdryers applyjoint compoundor about 1-1/2wraps of Teflontape _ 1

over threadedconnectionon the end of the gas pipe. (See figure 17.)

An elbow isrecommended,for additionaldepth, pointing downto allow

the unit to be locatedfurtherback intothe alcove. (Seefigure 18.)

Note: Pipejoint compoundmustbe resistantto the action of anyliquefied

petroleumgas.

Add additionalfittingto connectthe 3/8 inch gaspipe to a femalethreaded

end of a 3/4 inchflexibleconnector makingsure the connectionistight. Figure 17

(See figure 19.)

Makesuretheshutoffvalveon theendof thegaspipe isclosedandconnecttothe gassupply.

Opengasservicevalve and check all gassupplyconnectionsfrom servicevalveto shutoffvalve for

leaksusinga soap solution, DO NOT use an openflame to checkfor

gas leaks. Ifbubbles occur,tightenthe connectionsand recheck.

NOTE: Asa courtesy,manylocal gas utilitieswill inspecta gasapplianceinstallation. Checkwith your

local utilityto see if this serviceis providedin your area.

NOTE: The minimumpermissiblegas(naturalor mixed)supply pressureforpurposesof input

adjustmentis 4.5 inchesof water.

Figure18 Figure 19

1 0, Laythe dryer on itsside using 2 of the

cardboardcornerpoststo protectthe side of

the cabinet. (See figure20.) Remove

protectivefilm fromthe control panel,and using

a 5/16 inch nut driver,removethe shipping

bolts (3) securingthe wood shippingbaseto

the bottom of the upperdryer.

Figure20

Page 13

11, For gas dryers:

Removeyellowthread protectorfromunion. (See figure21.)

Positionthe dryerupright in front of the washer,with the rear of the dryer facingthe washer. Toprevent

damageto floorsdo notslide the dryeron the floor!

NOTE: Forgasdryeralcoveinstallation,plug powercord fordryer intoan outlet MAKINGSURE FIRST

THATOUTLETIS NOTENERGIZEDpriorto liftingdryer ontowasher.

Holdingthe base to supportbracket,removethe 2#10 hex head screwsand base supportbrackets

(notehowthe bracketsare inserted)located atthe front of the dryer base,markedwith orange labels.

(See figures22 &23.) NOTE: Bracketsand screwswill be used later.

A protectiveconduit (plastic)is providedforthe powercord. Installthe conduit overthe powercord.

The conduitis slit to facilitate installation. (See figure24.)

Yellow

Thread

Protector Hex Base

Head

Screw Bracket

Figure21 Figure22

Base

Bracket

Figure23 Figure24

Page 14

12, For electricdryers: I

TO MAKE ELECTRICALCONNECTIONFOR U.S.DRYERS

Reviewelectricalrequirementsonpage 6 of theseinstructions.

IMPORTANT- All U.S. modelsare producedfor a 3-WIRESYSTEM /®l _er_ I®

CONNECTION. Thedryer frame isgroundedto the neutralconductor

at the terminalblock. A 4-WIRE SYSTEMCONNECTIONis required

for newor remodeledconstruction,mobile homes,or if local codesdo

notpermit groundingthroughneutral. If the 4-wiresystemis used, _ _ |

the dryerframecannotbe groundedto the neutralconductorat the / O

terminalblock. Referto the followinginstructionsfor 3-and 4-WIRE ,Figure 25

SYSTEMCONNECTIONS.

Removethe terminalblock cover plate. (See figure25.) I i

A protectiveconduit(plastic)is providedforthe powercord. Cutthe

conduitsothat it isapproximately18 inchesshorterthan the power

cordandthreadthe powercordthroughthe conduit. (Seefigures26 &

27.)

Insertthe powercord with a U.L.listedstrain reliefthroughthe hole Figure26

providedinthe cabinetnearthe terminal block. Note, a strain relief

must be used.

3-WIRE SYSTEM CONNECTIONS

Do not loosenthe nuts alreadyinstalledonthe terminalblock. Be

sure they aretight. Usea 3/8 inchdeep nut driver.

Ifthe powercord hasterminals,placethe terminals overthe existing

nutsonthe posts. The neutral (whiteorcenter wire on powercord) Figure27

conductormust alwaysbe connectedto the center (silvercolored)

postofthe terminal block. 3-Wire System with

Securein placeusingthe nuts providedin the parts oackage. If the ,__,,_Power

Cord Attached

powercord does not haveterminals, usethe cuppedwashersahead

of the nuts. Ground

Besure the terminalblock nutsaretight. Securethe powercord in

position. Tightenthe strain reliefscrew(s)in order to clamp the strain

reliefto the cord. (See figure28.)

Replacethe terminalblock cover. Neutral

BEFOREOPERATINGOR TESTING,followthe groundingdirections

on page 5. Strain

4-WIRE SYSTEM CONNECTIONS relief

Removetheground strap screw fromthe terminalblock support. Fold Figure28

the groundstrap over so bothendsof the ground strap are attached

to the centerterminalblock post. 4-Wire System with

Connectthe neutral (white)conductorof the cord to the center (silver) Power Supply Attached

postof theterminal block. Connectthe grounding(green)wire of the

cord to the terminalblock supportusingthe groundstrap screw. -- ° Folded

Connectthe redand blackwires of the cord to the outer posts ofthe Neutral _ _.'_'_ Ground

terminalblock. Post ----. __/ StrapBe surethe terminalblock nutsare ontight. Securethe powercord in

positiOn.reliefto theTightencord,the(seeStrainfigurerelief29.)screw(s)in orderto clamp the strain •///__ /e NeutralReplacethe terminalblock cover. Strain

WARNING: If convertingfrom 4-wireelectricalsystemsto 3-wire,the o _ Relief

groundstrap mustbe reconnectedto terminalblock supportto ground (_ 4''/

thedryer frameto the neutral conductor. Figure29

Page 15

2-WIRE AND GROUND SYSTEM CONNECTIONS

2-Wire and Ground System

Removetheterminalblockcoverplate.

Insertthepowercordwithanagencylistedstrainrelief (" _

throughtheholeprovidedinthe cabinetneartheterminal _ o

block. Note,a strainreliefmustbe used. __

Donotloosenthenutsalreadyinstalledontheterminal Neutral

block. Besuretheyaretight. Use a 3/8 inchdeepwell Post" Power

o o Cord

socket. Ground

Securethe powercord groundwiretothe terminalblock _;Je ,Wire

supportusingthe groundscrew. (Seefigure 30.)

Ifthe powercord hasterminals, placethe terminalsover

the existing nutsonthe posts. The neutralwire in power

cord mustbe connectedto the center (silvercolored Power

cord

postofthe terminalblock. Neutral o f-_ _. • and

Securein placeusing the nutsprovidedin the parts ("Ah JF"/- strain

package. If the powercord does nothaveterminals f relief

usethe cuppedwashersahead of the nuts.

Be surethe terminal block nutsaretight. Securethe Figure30

powercord in position. Tightenthe strainreliefscrew(s)

in ordertoclampthestrainrelieftothe cord.

Replacethe terminalblock cover.

BEFOREOPERATINGOR TESTING, be surethe machineis properlygrounded.

EXPORT GAS MODELS

Exportgas modelsare manufacturedfor operationon either 230/240volt, 50 Hz or 220volt, 60 HzAC

approvedelectricalservicewith a 15amperefuse or circuit breaker.

Exportgas models havebeen manufacturedfor use with naturalgas having a higher heatingvalue of approxi-

mately 1025 BTUpercubicfoot. Conversionto LPgaswith a higherheatingvalue of approximately2500

BTU percubicfoot mustbe performedby a qualifiedservicetechnician. A conversionkitis available.

For electric dryers in alcove installation:

MAKINGSURE FIRST THATOUTLETIS NOT ENERGIZED,plugpowercordfor dryerintoan outletpriorto

liftingdryer ontowasher.

13.Makesurethat the exhaustseal isin placeand evenwith the end of the exhaustpipe.

(Seefigures31 & 32.)

Figure31 Figure32 Figure33

Makesurefront tabsare not bent, usescrewdriverto straightentabs if bent. (See figure33.)

Page 16

1 4, Two people,one on eachside,grasp andliftthe dryeronto the washer (seefigure 34),takingcare not to

bendthe tabs locatedtowardsthe frontof the washer. Slide the upperdryertowardthe rear makingsure

that theguidesfall betweenthe railson the supportof the washer. (Seefigure35.)

WARNING: Makesure POWERIS NOT SUPPLIEDTO OUTLETduringinstallation.

Whenplacingthe dryeronto the washer, makesure the POWERCORDIS NOTPINCHEDbetween

the washer andthe dryer or betweenthe exhaust pipeand bracket. If the dryercannot be pushedall

the way back, checkto see if the powercord is beingpinchedbetween the back ofthe dryerand the

exhaust bracket.

Makesure that SHUT-OFFFOR UTILITIES(electric,gas and water) WILL BEACCESSIBLEafter the

applianceis installed.

Figure34 Figure35

15.Checkto makesure the tabs on the washer are engaged in slots atthe front of the base ofthe dryer.

(See figures36 & 37 - somecomponentsremovedfor clarity.)

Front Right

Dryer

Base

Figure36 Figure37

Rotateforward to check engagement.

Page 17

16.Insert the base to support brackets (removed in step 11) on both sides the upper base and secure with

the screws also removed in step 12. (See figures 38 & 39.)

.... " _" o ppL'u--or"

\\\

Dryer _\_ -\

Base - _

"/ Tab /_

...., _; Screw

Figure 38 Figure 39

17.Raise gas pipe with shut off valve up and secure to gas valve union• (See figure 40.) Tighten fitting

with a crescent wrench being careful not to over tighten. (See figure 41.)

Do not apply teflon tape or pipe sealing compound to the threads of the shut off valve. This is a

brass expansion sleeve fitting.

Figure 40 Figure 41

Page18

18.Openthe gas shutoffvalve insidethe upperdryer (see figures42 & 43), and checkthe union

connectionto the gas valvefor leaks usinga soap solution,DO NOTuse an open flame to check for

gas leaks. If bubblesoccur,tighten the connectionsand recheck. Makesure notto let solutiondrip

into any electricalconnectororcomponent.

NOTE: As a courtesy,manylocal gasutilitieswill inspecta gasapplianceinstallation. Checkwith your

local utilityto seeif this serviceis providedin your area.

NOTE: The minimumpermissiblegas (naturalor mixed)supply pressurefor purposesof input

adjustmentis4.5 inchesof water.

Figure42 Figure43

19.Removewire harnessesand plasticclipsfrom base (see figure44) andconnect each harnessto the

connectorin the washermakingsure lockingtabs areengaged,and harnessis tucked out ofthe way of

the dispenser. (Seefigures45 & 46.)

Figure45

7 ii_iii

Figure44

Figure 46

Page 19

Page is loading ...

Maytag Washer/Dryer User manual

Brand: Maytag

Model: Washer/Dryer

Category: Networking

Type: User manual

This manual is also suitable for

6 2708140-0498

Download PDF

report

Maytag Washer/Dryer User manual

This manual is also suitable for

Maytag Washer/Dryer User manual

Related papers

Other documents