PACOM PAC-24WM0808 User manual

PACOM
Brand
PACOM
Model
PAC-24WM0808
Category
Power extensions
Type
User manual
CCTV Power Supply Manual
8 Channel 8Amps
24VAC Wall Mount
Model: PAC-24WM0808(S84746)
24VAC Wall Mount
Model: PAC-24WM0808(S84746)
8
Overview: This PACOM Wall Mount CCTV Power Supply provides 24VAC distributed
via eight (8) PTC protected outputs for powering CCTV Cameras and other video
accessories.
Notes: Power On/Off Switch has been provided at the Bottom of the cabinet
Caution: Always test for correct output voltage ( 24VAC) before connecting power to
cameras or other equipment. Temporarily power up the unit and measure the AC
output voltage to avoid damage to devices. Then disconnect power before connecting
external devices.
1. Mount unit in the desired location (Space unit at least 100mm from any video
monitors). Do not obstruct side air vents. Use L brackets provided for bottom fixing.
2. Unplug Green terminal connector blocks from their sockets for easy installation.
3. Tech Tip: All Cameras with similar power cable length should be grouped together on
the same terminal block.
4. Connect cameras or other equipment power input cables to the screw terminals side
by side in pairs.
5. Screw the terminals closed, making sure that there are no loose connections. Once
this is done, insert the terminal block back into its correct slot.
6. Connect the unit’s power cord to a 240VAC outlet. Switch on power to the unit.
7. Front-panel LEDs should illuminate Green if the Channel is not being used and Blue if
the channel or channels are being used.
Red if the Channel has a short circuit on the output lines.
8. Test the output at the camera end of each power cable to be sure that the voltage is
within range as specified by the Camera manufacturer.
9. Volt meter operational range 5V - 69.9V
10. Amp meter operational range 200mA -8Amp
For current load > 8 Amps ,<9 Amps Amp Meter display will Flash the current value
For current Load Greater than 9.00 Amps, the Amp Meter display will
read OL= Over Load.
11. Ry-NC is a normally closed relay contact.
Tri-Colour LED status indicator for each output:
CAUTION: To reduce the risks of electric shock do not open enclosure. There is no user
serviceable parts inside. Refer servicing to qualified service personnel.
Replace fuses with the same type and rating T1.5A/250V
Wall Mount Mechanical Dimensions 280*231*83mm
PAC-24WM0808(S84746) PAC-24WM0808(S84746)
PAC-24WM0808(S84746)
Green
Blue
Red
Open
Circuit
Closed Circuit
< 120mA load
Short Circuit
PTC Fuse tripped
Procedure for resetting PTC fuse:
• Remove short in the circuit.
• Switch off PSU switch for a period of 30 seconds, then switch back on and PTC fuse
will reset automatically.
2 3
Specifications
PAC-24WM0808(S84746) PAC-24WM0808(S84746)
Parallel Output Configuration
12
AWG
55m
14
AWG
35m
16
AWG
22m
18
AWG
14m
20
AWG
9m
22
AWG
8m
12
AWG
73m
14
AWG
46m
16
AWG
29m
18
AWG
18m
20
AWG
12m
22
AWG
7m
12
AWG
110m
14
AWG
69m
16
AWG
44m
18
AWG
27m
20
AWG
18m
22
AWG
17m
12
AWG
138m
14
AWG
87m
16
AWG
55m
18
AWG
34m
20
AWG
22m
22
AWG
21m
12
AWG
184m
14
AWG
116m
16
AWG
73m
18
AWG
46m
20
AWG
30m
22
AWG
29m
24
AWG
32m
24
AWG
16m
24
AWG
10m
24
AWG
8m
24
AWG
6m
24
AWG
5m
24
AWG
3m
22
AWG
43m
20
AWG
44m
18
AWG
69m
16
AWG
109m
14
AWG
174m
12
AWG
276m
22
AWG
86m
20
AWG
87m
18
AWG
137m
16
AWG
218m
14
AWG
348m
12
AWG
552m
24VAC Cable Distance (meters)
24
AWG
65m
22
AWG
103m
20
AWG
175m
18
AWG
260m
16
AWG
414m
14
AWG
659m
12
AWG
1052m
5VA
(208ma)
10VA
(417ma)
20VA
(833ma)
30VA
(1.250ma)
40VA
(1.667ma)
50VA
(2.083ma)
75VA
(3.125ma)
100VA
(4.167ma)
12
AWG
55m
AWG
35m
16
AWG
22m
18
AWG
14m
20
AWG
9m
22
AWG
8m
12
AWG
73m
14
AWG
46m
16
AWG
29m
18
AWG
18m
20
AWG
12m
22
AWG
7m
12
AWG
110m
14
AWG
69m
16
AWG
44m
18
AWG
27m
20
AWG
18m
22
AWG
17m
12
AWG
138m
AWG
87m
16
AWG
55m
18
AWG
34m
20
AWG
22m
22
AWG
21m
12
AWG
184m
AWG
116m
16
AWG
73m
18
AWG
46m
20
AWG
30m
22
AWG
29m
24
AWG
32m
24
AWG
16m
24
AWG
10m
24
AWG
8m
24
AWG
6m
24
AWG
5m
24
AWG
3m
22
AWG
43m
20
AWG
44m
18
AWG
69m
16
AWG
109m
AWG
174m
12
AWG
276m
22
AWG
86m
20
AWG
87m
18
AWG
137m
16
AWG
218m
14
AWG
348m
12
AWG
552m
24VAC Cable Distance (meters)
24
AWG
65m
22
AWG
103m
20
AWG
175m
18
AWG
260m
16
AWG
414m
AWG
659m
12
AWG
1052m
5VA
(208ma)
10VA
(417ma)
20VA
(833ma)
30VA
(1.250ma)
40VA
(1.667ma)
50VA
(2.083ma)
75VA
(3.125ma)
100VA
(4.167ma)
Load
Load
Load
By connecting more than 1 output in parallel the normal
current availability can be doubled, tripled or even quadrupled
Normal Current Limit X 2
Normal Current Limit X 3Load
Normal Current Limit X 4
4 5
PAC-24WM0808(S84746) PAC-24WM0808(S84746)
Troubleshooting
1. Power does not turn on • Check front panel leds and rear main fuse
• Ensure power cord is firmly in its socket and the switch
is in the on position
• Ensure you have 240VAC supply to the Power
Supply Unit
2. led’s are RED even • To reset PTC , turn of power and wait for 30 sec,
then restart unit though there is no short circuit
3. Voltage drop is large • Use thicker guage wire
4. Camera case is hot • Check that the correct voltage is supplied to
the camera
5. Amp Meter display • Power Supply load is approaching maximum current limit
Flashes continously
6. Amp Meter display •
reads OL
Power Supply unit has exceeded its maximum load
capacity. Disconnect 1 or more devices until Amp Meter
shows a reading less than the maximum capacity.
6 7
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

PACOM PAC-24WM0808 User manual

PACOM
Brand
PACOM
Model
PAC-24WM0808
Category
Power extensions
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents