Baumer BMMS K34 analog Installation and Operating Instructions

Baumer
Brand
Baumer
Model
BMMS K34 analog
Type
Installation and Operating Instructions

This manual is also suitable for

Page is loading ...
Page is loading ...
Baumer Electric AG
Hummelstrasse 17
8501 Frauenfeld / Switzerland
Phone +41 52 728 11 22 · Fax +41 52 728 11 44
sales.ch@baumer.com · www.baumer.com
Printed in Switzerland · 01.18
Version 03 · 81195324
Subject to modication in technic and design.
Errors and omissions excepted.
EN
Assembly instruction and
safety information
(Translation of original instruction)
BMMS K, BMMS M - Analog
Cable transducer with analog interface
1. Identicationofnotes
Note
Information for intended product use.
2. Technical data
Voltage supply 10...30 VDC (UL Class 2)
Consumption w/o load: typ. 50 mA (24 VDC)
R
ø
ø = 5.3 mm
R x ≥27 mm
R exible ≥55 mm
3. Intended use
The cable transducer is a precision measuring
device that is used to record linear positions and
speeds. It provides measuring values as electronic
output signals for the subsequently connected
device. It must not be used for any other purpose.
Unless this product is specially labeled, it may
not be used for operation in potentially explosive
environments.
Make sure by appropriate safety measures, that
in case of error or failure of the cable transducer,
no danger to persons or damage to the system or
operating facilities occurs. Do not directly connect
with on board supply system but with a DC/DC
converter which is released by automotive standar-
dization group.
4. Personnelqualication
Installation and assembly of this product may be performed
only by a person qualied in electronics and precision
mechanics.
5. Maintenance
The cable transducer is maintenance-free and must not
be opened up nor mechanically or electronically modied.
Opening up the cable transducer can lead to injury caused
by the spring.
6. Recommended grounding concept
screen connection
7. Terminal assignment
See type designation: BMMS.xxxxx24
xx/xx00x
U/5/Y/7 = voltage output / V/Z = current output / W = current/voltage output
7.1 Cable
Non redundant Redundant
Colour U/5 V W Y/7 Z
white (wh) 0 V 0 V 0 V 0 V 0 V
brown (bn) +Vs +Vs +Vs +Vs 1 +Vs 1
green (gn) d.u. Iout Iout Uout 1 lout 1
yellow (ye) Uout d.u. Uout Uout 2 lout 2
grey (gy) Set Set Set Set 1 Set 1
pink (pk) DV/Status DV/Status DV/Status DV/Status1 DV/Status1
blue (bu) – – – Set 2 Set 2
red (rd) – – – DV/Status2 DV/Status2
black (bk) – – – 0 V 0 V
violet (vt) – – – +Vs 2 +Vs 2
Cable 6 x 0.14 mm
2
/ 10 x 0.14 mm
2
Screen: connected to housing.
7.2 Flange connector M12, 5-pin
Non redundant 1xM12 Redundant 2xM12
1)
Pin U/5 V W Y/Z Z
1 0 V 0 V 0 V 0 V 0 V
2 +Vs +Vs +Vs +Vs +Vs
3 d.u. Iout Iout Uout Iout
4 Uout d.u. Uout DV/Status DV/Status
5 Set Set Set Set Set
1
2
3
4
5
1) Terminal assignment for each M12 connector
7.3 Flange connector M12, 8-pin
Non redundant Redundant
Pin U/5 V W Y/7 Z
1 0 V 0 V 0 V 0 V 0 V
2 +Vs +Vs +Vs +Vs +Vs
3 d.u. Iout Iout Uout1 lout1
4 Uout d.u. Uout Uout2 lout2
5 Set Set Set Set1 Set1
6 DV/Status DV/Status DV/Status DV/Status1 DV/Status1
7 n.c. n.c. n.c. Set2 Set2
8 n.c. n.c. n.c. DV/Status2 DV/Status2
1
3
4
2
5
6
7
8
For customer-specic cable transducers please refer to product label and data sheet.
8. General informations
Protect cable transducer and measuring wire as far as
possible from water. Avoid mounting with measuring wire
outlet pointing upwards (especially in outdoor applications)
to reduce risk of water entry. Freezing water can lead to
damage. Drainage holes can be opened to allow water
to drain. Prefer mounting cable transducer with drainage
holes in low position.
>3°
>3°
<3°
Ensure pulling out of measuring wire in straight direction.
Maximum misalignment ≤3°. Use pulley to limit misalign-
ment. Do not loop measuring wire around objects or allow
them to touch measuring wire. Protect measuring wire
from dirt and damage.
Ensure free rotation of measuring wire xation to assure
optimum wire guiding.
Letting snap back of pulled out measuring wire can cause
injuries and damage of cable transducer.
10. Teach process
Activate teach process
Set “Set-input” on HIGH for 6 seconds and afterwards on
LOW level.
DV/Status output: Oscillates after 5 seconds.
Position1
Get cable transducer on position 1 intended for voltage
output 1 / current output 1. Set “Set-input” for 1 second on
HIGH level.
DV/Status output: Switches to HIGH level for 3 seconds
and ashes shortly.
Position2
Get cable transducer on position 2 intended for voltage
output 2/current output 2. Set “Set-input” for 1 second on
HIGH level.
DV/Status output: Switches to LOW level for 3 seconds
and oscillates afterwards.
If measuring range is exceeded or the limits are too close
to each other, the teaching process was not successful and
has to be repeated.
Set / restore default
Set „Set-input“ for 16 seconds to HIGH. DV/Status output:
Oscillates after 5 seconds. Note: The cable transducer hast
to be completely drawn in.
Behavior
U
m
Pos 2
Pos 1
Pos 2
Pos 1
Teach in direction - move in
Teach in direction - move out
11. Disposal
The cable transducer contains electronic components.
At its disposal, local environmental guidelines must be
followed.
9. Mounting
BMMS K
2.
1.
M4 DIN912 (3x)
max. 2.5 Nm
BMMS M
1.
2.
M6 DIN912 (3x)
max. 2.5 Nm
Fit cable transducer on a plain base to avoid excessive force on housing. Make sure that drainage holes are free. It is
recommended to use at washers.
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10

Baumer BMMS K34 analog Installation and Operating Instructions

Baumer
Brand
Baumer
Model
BMMS K34 analog
Type
Installation and Operating Instructions
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Related papers

Other documents