2. LG
  3. 19LD330
19LD330

LG 19LD330 Owner's manual

  • Hello! I am an AI chatbot trained to assist you with the LG 19LD330 Owner's manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
Page is loading ...
2
3
SAFETY INSTRUCTIONS
ENGLISH
• Please read these safety precautions carefully before using the product.
• In this manual, the illustration may be somewhat different from your product because it is just example to help the instruction.
If you ignore the warning message, you may be seriously injured or there is a possibility of accident or death.
If you ignore the caution message, you may be slightly injured or the product may be damaged.
Precaution in Installing the Product
WARNING
WARNING
CAUTION
Keep away from heat sources like electrical heaters.
- Electrical shock, fire, malfunction or deformation may occur.
If you can smell smoke or other odors or hear a strange
sound unplug the power cord and contact the service
center.
- If you continue to use without taking proper measures, elec-
trical shock or fire can occur.
Do not use the product in damp place such as a bath-
room or any place where it is likely to get wet.
- This may cause a fire or could give an electric shock.
Install the product on a flat and stable place that
has no risk of dropping the product.
- If the product is dropped, you may be injured or the
product may be broken.
Keep the product away from direct sunlight.
- The product can be damaged.
Do not place the product in a built-in installation
such as bookcase or rack.
- Ventilation required.
Electrical Power Related Precautions
Make sure to connect the power cable to the ground-
ed current.
- You may be electrocuted or injured.
Do not touch the power plug with wet hands.
Additionally, it the cord pin is wet or covered with
dust, dry the power plug completely or wipe dust off.
- You may be electrocuted due to excess moisture.
During a thunder or lightning storm, unplug the
power cable or signal cable.
- You may be electrocuted or a fire can break out.
Protect the power cord from physical or mechanical
abuse, such as being twisted, kinked, pinched, closed in
a door, or walked upon. Pay particular attention to plugs,
wall outlets, and the point where the cord exits the
appliance.
Precautions in Moving the Product
Do not shock the product when moving it.
- You may be electrocuted or the product can be dam-
aged.
Make the panel face forward and hold it with both
hands to move.
- If you drop the product, the damaged product can
cause electric shock or fire. Contact with the service
center for repair.
Make sure to turn off the product.
Make sure to remove all cables before moving the
product.
- You may be electrocuted or the product can be dam-
aged.
Precautions in Using the Product
Do not disassemble, repair or modify the product at
your own discretion.
- Fire or electric shock accident can occur.
- Contact the service center for check, calibration or
repair.
To reduce the risk of fire or electric shock, do not
expose this apparatus to rain or moisture.
Apparatus shall not be exposed to dripping or
splashing and no objects filled with liquids, such as
vases, shall be placed on the apparatus.
WARNING
WARNING
CAUTION
CAUTION
CAUTION
CAUTION
WARNING
Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power supply cord or plug
is damaged, liquid has been spilled or objects have
fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate normal-
ly, or has been dropped.
IMPORTANT INFORMATION TO PREVENT “IMAGE BURN
/BURN-IN” ON YOUR TELEVISION SCREEN
-
When a fixed image (e.g. logos, screen menus, video game, computer
display and teletext pages) is displayed on the television for an extend-
ed period it can become permanently imprinted on the screen. This
phenomenon is known as “image burn” or “burn-in”. Image burn is not
covered under the manufacturer’s warranty.
-
In order to prevent image burn, avoid displaying a fixed image on your
television’s screen for a prolonged period (2 or more hours for LCD, 1
or more hours for Plasma).
-
Image burn can also occur on the letterboxed areas of your television
if you use the 4:3 aspect ratio setting for an extended period.



ร้อนเข้าใกล้








































 




3
SAFETY INSTRUCTIONS
ENGLISH
• Please read these safety precautions carefully before using the product.
• In this manual, the illustration may be somewhat different from your product because it is just example to help the instruction.
If you ignore the warning message, you may be seriously injured or there is a possibility of accident or death.
If you ignore the caution message, you may be slightly injured or the product may be damaged.
Precaution in Installing the Product
WARNING
WARNING
CAUTION
Keep away from heat sources like electrical heaters.
- Electrical shock, fire, malfunction or deformation may occur.
If you can smell smoke or other odors or hear a strange
sound unplug the power cord and contact the service
center.
- If you continue to use without taking proper measures, elec-
trical shock or fire can occur.
Do not use the product in damp place such as a bath-
room or any place where it is likely to get wet.
- This may cause a fire or could give an electric shock.
Install the product on a flat and stable place that
has no risk of dropping the product.
- If the product is dropped, you may be injured or the
product may be broken.
Keep the product away from direct sunlight.
- The product can be damaged.
Do not place the product in a built-in installation
such as bookcase or rack.
- Ventilation required.
Electrical Power Related Precautions
Make sure to connect the power cable to the ground-
ed current.
- You may be electrocuted or injured.
Do not touch the power plug with wet hands.
Additionally, it the cord pin is wet or covered with
dust, dry the power plug completely or wipe dust off.
- You may be electrocuted due to excess moisture.
During a thunder or lightning storm, unplug the
power cable or signal cable.
- You may be electrocuted or a fire can break out.
Protect the power cord from physical or mechanical
abuse, such as being twisted, kinked, pinched, closed in
a door, or walked upon. Pay particular attention to plugs,
wall outlets, and the point where the cord exits the
appliance.
Precautions in Moving the Product
Do not shock the product when moving it.
- You may be electrocuted or the product can be dam-
aged.
Make the panel face forward and hold it with both
hands to move.
- If you drop the product, the damaged product can
cause electric shock or fire. Contact with the service
center for repair.
Make sure to turn off the product.
Make sure to remove all cables before moving the
product.
- You may be electrocuted or the product can be dam-
aged.
Precautions in Using the Product
Do not disassemble, repair or modify the product at
your own discretion.
- Fire or electric shock accident can occur.
- Contact the service center for check, calibration or
repair.
To reduce the risk of fire or electric shock, do not
expose this apparatus to rain or moisture.
Apparatus shall not be exposed to dripping or
splashing and no objects filled with liquids, such as
vases, shall be placed on the apparatus.
WARNING
WARNING
CAUTION
CAUTION
CAUTION
CAUTION
WARNING
Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power supply cord or plug
is damaged, liquid has been spilled or objects have
fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate normal-
ly, or has been dropped.
IMPORTANT INFORMATION TO PREVENT “IMAGE BURN
/BURN-IN” ON YOUR TELEVISION SCREEN
-
When a fixed image (e.g. logos, screen menus, video game, computer
display and teletext pages) is displayed on the television for an extend-
ed period it can become permanently imprinted on the screen. This
phenomenon is known as “image burn” or “burn-in”. Image burn is not
covered under the manufacturer’s warranty.
-
In order to prevent image burn, avoid displaying a fixed image on your
television’s screen for a prolonged period (2 or more hours for LCD, 1
or more hours for Plasma).
-
Image burn can also occur on the letterboxed areas of your television
if you use the 4:3 aspect ratio setting for an extended period.
3
SAFETY INSTRUCTIONS
ENGLISH
• Please read these safety precautions carefully before using the product.
• In this manual, the illustration may be somewhat different from your product because it is just example to help the instruction.
If you ignore the warning message, you may be seriously injured or there is a possibility of accident or death.
If you ignore the caution message, you may be slightly injured or the product may be damaged.
Precaution in Installing the Product
WARNING
WARNING
CAUTION
Keep away from heat sources like electrical heaters.
- Electrical shock, fire, malfunction or deformation may occur.
If you can smell smoke or other odors or hear a strange
sound unplug the power cord and contact the service
center.
- If you continue to use without taking proper measures, elec-
trical shock or fire can occur.
Do not use the product in damp place such as a bath-
room or any place where it is likely to get wet.
- This may cause a fire or could give an electric shock.
Install the product on a flat and stable place that
has no risk of dropping the product.
- If the product is dropped, you may be injured or the
product may be broken.
Keep the product away from direct sunlight.
- The product can be damaged.
Do not place the product in a built-in installation
such as bookcase or rack.
- Ventilation required.
Electrical Power Related Precautions
Make sure to connect the power cable to the ground-
ed current.
- You may be electrocuted or injured.
Do not touch the power plug with wet hands.
Additionally, it the cord pin is wet or covered with
dust, dry the power plug completely or wipe dust off.
- You may be electrocuted due to excess moisture.
During a thunder or lightning storm, unplug the
power cable or signal cable.
- You may be electrocuted or a fire can break out.
Protect the power cord from physical or mechanical
abuse, such as being twisted, kinked, pinched, closed in
a door, or walked upon. Pay particular attention to plugs,
wall outlets, and the point where the cord exits the
appliance.
Precautions in Moving the Product
Do not shock the product when moving it.
- You may be electrocuted or the product can be dam-
aged.
Make the panel face forward and hold it with both
hands to move.
- If you drop the product, the damaged product can
cause electric shock or fire. Contact with the service
center for repair.
Make sure to turn off the product.
Make sure to remove all cables before moving the
product.
- You may be electrocuted or the product can be dam-
aged.
Precautions in Using the Product
Do not disassemble, repair or modify the product at
your own discretion.
- Fire or electric shock accident can occur.
- Contact the service center for check, calibration or
repair.
To reduce the risk of fire or electric shock, do not
expose this apparatus to rain or moisture.
Apparatus shall not be exposed to dripping or
splashing and no objects filled with liquids, such as
vases, shall be placed on the apparatus.
WARNING
WARNING
CAUTION
CAUTION
CAUTION
CAUTION
WARNING
Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power supply cord or plug
is damaged, liquid has been spilled or objects have
fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate normal-
ly, or has been dropped.
IMPORTANT INFORMATION TO PREVENT “IMAGE BURN
/BURN-IN” ON YOUR TELEVISION SCREEN
-
When a fixed image (e.g. logos, screen menus, video game, computer
display and teletext pages) is displayed on the television for an extend-
ed period it can become permanently imprinted on the screen. This
phenomenon is known as “image burn” or “burn-in”. Image burn is not
covered under the manufacturer’s warranty.
-
In order to prevent image burn, avoid displaying a fixed image on your
television’s screen for a prolonged period (2 or more hours for LCD, 1
or more hours for Plasma).
-
Image burn can also occur on the letterboxed areas of your television
if you use the 4:3 aspect ratio setting for an extended period.
 
 

















 



   
    
   


   



3
3
ENGLISH
Connecting your Unit
ANTENNA
IN
COMPONENT IN
AUDIO
VIDEO
ANTENNA
IN
L(MONO)
R
AUDIO
VIDEO
AV IN1
HDMI/DVI IN
1
AUDIO IN
(RGB/DVI)
USB IN
SERVICE ONLY
RGB IN
(PC)
RS-232C IN
(CONTROL)
2
L/MONO
R
AUDIO
VIDEO
AV IN1
VCR Connection
2
DVD/STB
2
Antenna Connection
1
Power Cord
3
�
Here shown may be somewhat different from your set.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
* To connect an additional equipment, see the
External Equipment Setup
section in CD Manual.








4
4
ACCESSORIES
ENGLISH
Bolts for stand assembly
(Refer to p.11)
x 4
Protection cover
(Refer to p.12)
Ensure that the following accessories are included with your TV.
If an accessory is missing, please contact the dealer where you purchased the TV.
�
Image shown may be somewhat different from your TV.
Owner’s Manual
Batteries (AAA)
Power Cord
Polishing Cloth
Polishing cloth for use on the screen.
This item is not included for all models.
* Lightly wipe any stains or fingerprints on
the surface of the TV with the polishing
cloth.
Do not use excessive force. This may cause
scratching or discolouration.
Remote Control
P
A
G
E
P
123
45
0
6
789
LIST
Q.VIEW
AV MODE INPUTENERGY
SAVING
MARK
FAV
RATIO
MUTE
OK
MENU
Q.MENU
BACK
EXIT
CLEAR
VOICE 2
Only 19/22LD3**
Protection cover
(Refer to p.12)
Cable Holder
(Refer to p. 13)
Bolts for stand assembly
(Refer to p.10)
Only 26/32LD3**
Protection cover
(Refer to p.12)
x 8
M4 x 20
1-screw for stand fixing
(Refer to p.11)
Wall Mounting Bracket(Separate purchase)
R W 12 0
(19/22LD3**)
RW230
(26/32LD3**, 32LD4**)
AW-47LG30M
(32LD3**, 32/42LD4**)
Only 32/42LD4**
Only 26/32LD3**,
32/42LD4**
P
A
G
E
P
123
45
0
6
789
LIST
Q.VIEW
AV MODE INPUTENERGY
SAVING
MARK
FAV
RATIO
MUTE
OK
MENU
Q.MENU
BACK
EXIT
or




































3
ENGLISH
■ Image shown may differ from your TV.
■ To connect an additional equipment, see the External equipment Setup section in CD Manual.
CONNECTING YOUR UNIT
RGB IN
(PC)
RS-232C IN
(CONTROL & SERVICE)
AUDIO IN
(RGB/DVI)
ANTENNA /
CABLE IN
CO MPONEN T IN
/DVI IN
WIRELESS
CONTROL
OPTICAL
DIGITAL
AUDIO OUT
R
1
2
COMPONENT IN
AUDIO
VIDEO
L/MONO
AUDIO
VIDEO
AV IN1
1
2
VCR Connection
2
DVD/STB
2
Antenna
Connection
1
Power Cord
3
TO VIEW THE USER'S GUIDE ON THE CD-ROM
To view the User's guide on the CD-ROM, Adobe Acrobat Reader must be installed on your PC.
The "ACRORD" folder on the CD-ROM contains the installation program for Acrobat Reader.
If you want to install Acrobat Reader, Open "My Computer" Open the folder "LG" Open the folder
"ACRORD" double-click your language.
To view the User's guide
The User's guide files are included in the supplied CD-ROM.
Load the supplied CD-ROM into the CD-ROM drive of your PC.
After a while, the web page of the CD-ROM will open automatically.(Windows users only)
If the web page does not appear automatically, open the User's guide file directly.
Open "My computer" Open the folder "LG" Double click the "index.htm" file.
TO VIEW THE SIMPLE MANUAL
You can easily and effectively access the TV information by viewing the simple manual on the TV.
Press the GREEN button, you can check the Simple manual menu.
Press the EXIT button to return to normal TV viewing.
1
2
Polishing Cloth
Polishing cloth for
use on the screen.
This item is not included for all models.
* Lightly wipe any stains
or fingerprints on the
surface of the TV with
the polishing cloth.
Do not use excessive
force. This may cause
scratching or discoloura-
tion.







5
5
PREPARATION
ENGLISH
FRONT PANEL CONTROLS
�
Image shown may be somewhat different from your TV.
P
OK
MENU
INPUT
PROGRAMME
VOLUME
OK
MENU
POWER
INPUT
Only 26/32LD3**
PROGRAMME
VOLUME
OK
MENU
INPUT
POWER
Only 19/22LD3**
Remote Control Sensor
Power/Standby Indicator
•
Illuminates red in standby mode.
• Illuminates blue when the TV is switched on.
G
Do not step on the glass stand or subject it to any impact.
It may break, causing possible injury from fragments of glass, or the TV may fall.
G
Do not drag the TV. The floor or the product may be damaged.
CAUTION
NOTE
!
G
The energy consumed during use can be significantly reduced if the level of brightness of the picture is
reduced, and this will reduce the overall running cost.
SPEAKER



4
ENGLISH
PREPARATION
FRONT PANEL CONTROLS
■ Image shown may differ from your TV.
PROGRAMMEVOLUMEMENU OKINPUTPOWER
Intelligent Sensor
Adjusts picture according to the
surrounding conditions.
NOTE
► The energy consumed during use can be significantly reduced if the level of brightness of the picture is
reduced, and this will reduce the overall running cost.
CAUTION
► Do not step on the glass stand or subject it to any impact.
It may break, causing possible injury from fragments of glass, or the TV may fall.
► Do not drag the TV. The floor or the product may be damaged.
Remote Control Sensor
Power/Standby Indicator
• Illuminates red in standby mode.
• The LED is off while the TV remains on.
Touch Sensor
• You can use the desired
button function by
touching.
4
ENGLISH
PREPARATION
FRONT PANEL CONTROLS
■ Image shown may differ from your TV.
PROGRAMMEVOLUMEMENU OKINPUTPOWER
Intelligent Sensor
Adjusts picture according to the
surrounding conditions.
NOTE
► The energy consumed during use can be significantly reduced if the level of brightness of the picture is
reduced, and this will reduce the overall running cost.
CAUTION
► Do not step on the glass stand or subject it to any impact.
It may break, causing possible injury from fragments of glass, or the TV may fall.
► Do not drag the TV. The floor or the product may be damaged.
Remote Control Sensor
Power/Standby Indicator
• Illuminates red in standby mode.
• The LED is off while the TV remains on.
Touch Sensor
• You can use the desired
button function by
touching.













Page is loading ...
7
7
ENGLISH
BACK PANEL INFORMATION
�
Image shown may be somewhat different from your TV.
K
AC-IN
1
Power Cord Socket
This TV operates on an AC power. The voltage is
indicated on the Specifications page. Never
attempt to operate the TV on DC power.
HDMI Input
Connect a HDMI signal to HDMI IN.
Or DVI(VIDEO)signal to HDMI/DVI port with DVI
to HDMI cable.
RGB IN Input
Connect the output from a PC.
RS-232C IN PORT
Connect to the RS-232C port on a PC.
This port is used for Service or Hotel mode.
SERVICE ONLY PORT
RGB/DVI Audio Input
Connect the audio from a PC.
Audio/Video Input
Connect audio/video output from an external
device to these jacks.
Component Input
Connect a component video/audio device to
these jacks.
Antenna Input
Connect RF antenna to this jack.
USB IN Input
Connect USB storage device to this jack.
1
2
3
4
5
7
6
8
9
COMPONENT IN
AUDIO
VIDEO
ANTENNA
IN
L(MONO)
R
AUDIO
VIDEO
AV IN
AUDIO IN
(RGB/DVI)
USB IN
SERVICE ONLY
RGB IN
(PC)
RS-232C IN
(CONTROL)
/DVI IN
2
8
9
3
6
7
Only
19/22LD33*
4 5
COMPONENT IN
AUDIO
VIDEO
ANTENNA
IN
L(MONO)
R
AUDIO
VIDEO
AV IN
AUDIO IN
(RGB/DVI)
RGB IN
(PC)
RS-232C IN
(CONTROL)
/DVI IN
2
8
9
3
6
7
4
10
Only
19/22LD34*
Only
19/22LD34*
10



















Page is loading ...
Page is loading ...
10
10
ENGLISH
PREPARATION
STAND INSTALLATION
�
Image shown may be somewhat different from your TV.
�
When assembling the desk type stand, check whether the bolt is fully tightened. (If not tightened fully, the
product can tilt forward after the product installation.) If you tighten the bolt with excessive force, the bolt can
deviate from abrasion of the tightening part of the bolt.
1
Carefully place the TV screen side down on a cush-
ioned surface to protect the screen from damage.
2
Assemble the TV as shown.
Only 19/22LD3
**
1
3
4
Carefully place the TV screen side down on a
cushioned surface to protect the screen from
damage.
2
Assemble the parts of the
S
tand Body
with
the
S
tand Base
of the TV.
Assemble the TV as shown.
Fix the 4 bolts securely using the holes in the
back of the TV.
Stand Body
Stand Base
Only 26/32LD3**
M4X20
M4X20













Page is loading ...
12
12
ENGLISH
PREPARATION
Insert the
P
rotection Cover
into the TV until
clicking sound.
�
Image shown may be somewhat different from your TV.
When installing the wall-mounted unit, use the protection cover.
NOT USING THE DESK-TYPE STAND
Loose the bolts from TV.
After removing the protection paper from the
protection cover, adhere it to the TV as shown.
Detach the
Stand
from
T V
.
2
3
4
Only 19/22LD3
**
1
Carefully place the TV screen side down on a cush-
ioned surface to protect the screen from damage.
Protection Cover
Insert the
P
rotection Cover
into the TV until clicking
sound.
Protection Cover
Only 26/32LD3
**
Only 32/42LD4
**
Protection Cover














13
13
ENGLISH
BACK COVER FOR WIRE ARRANGEMENT
�
Image shown may be somewhat different from your TV.
Only 19/22LD3
**
After Connecting the cables as necessary, install
CABLE HOLDER as shown and bundle the cables.
K
AC-IN
K
AC-IN
Connect the cables as necessary.
To connect additional equipment, see the External
Equipment Setup section of the manual.
1
Open the
C
able Management Clip
as shown
and manage the cables.
2
Cable Management Clip
Fit the
C
able Management Clip
as shown.
3
Only 26/32LD3**, 32/42LD4**
NOTE
!
G
Do not use the
C
able Management Clip
to lift
the TV.
- If the TV is dropped, you may be injured or the
TV may be damaged.
Cable Holder











  



14
14
PREPARATION
ENGLISH
SWIVEL STAND
(Except 19/22LD3**)
�
This feature is not available for all models.
�
After installing the TV, you can adjust the TV manually
to the left or right direction by 20 degrees to suit your
viewing position.
POSITIONING YOUR DISPLAY
(Only 19/22LD3**)
�
Image shown may be somewhat different from your
TV.
�
Adjust the position of the panel in various ways for
maximum comfort.
• Tilt range
12
0
3
0
KENSINGTON SECURITY SYSTEM
�
This feature is not available for all models.
�
Image shown may be somewhat different from your TV.
The TV is equipped with a Kensington Security
System connector on the back panel. Connect the
Kensington Security System cable as shown below.
For the detailed installation and use of the
Kensington Security System, refer to the user’s guide
provided with the Kensington Security System.
For further information, contact http://www.kensing-
ton.com, the internet homepage of the Kensington
company. Kensington sells security systems for
expensive electronic equipment such as notebook
PCs and LCD projectors.
AC IN
CABLE MANAGEMENT
NOTE
!
G
The Kensington Security System is an optional
accessory.
G
If the TV feels cold to the touch, there may be a
small “flicker” when when it is turned on.
This is normal, there is nothing wrong with TV.
G
Some minute dot defects may be visible on the
screen, appearing as tiny red, green, or blue
spots. However, they have no adverse effect on
the monitor's performance.
G
Avoid touching the LCD screen or holding your fin-
ger(s)
against it for long periods of time.
Doing so may produce some temporary distor-
tion effects on the screen.














 


   


   
 

  
  

 


14
PREPARATION
ENGLISH
SWIVEL STAND
(Except 19/22LD3**)
�
This feature is not available for all models.
�
After installing the TV, you can adjust the TV manually
to the left or right direction by 20 degrees to suit your
viewing position.
POSITIONING YOUR DISPLAY
(Only 19/22LD3**)
�
Image shown may be somewhat different from your
TV.
�
Adjust the position of the panel in various ways for
maximum comfort.
• Tilt range
12
0
3
0
KENSINGTON SECURITY SYSTEM
�
This feature is not available for all models.
�
Image shown may be somewhat different from your TV.
The TV is equipped with a Kensington Security
System connector on the back panel. Connect the
Kensington Security System cable as shown below.
For the detailed installation and use of the
Kensington Security System, refer to the user’s guide
provided with the Kensington Security System.
For further information, contact http://www.kensing-
ton.com, the internet homepage of the Kensington
company. Kensington sells security systems for
expensive electronic equipment such as notebook
PCs and LCD projectors.
AC IN
CABLE MANAGEMENT
NOTE
!
G
The Kensington Security System is an optional
accessory.
G
If the TV feels cold to the touch, there may be a
small “flicker” when when it is turned on.
This is normal, there is nothing wrong with TV.
G
Some minute dot defects may be visible on the
screen, appearing as tiny red, green, or blue
spots. However, they have no adverse effect on
the monitor's performance.
G
Avoid touching the LCD screen or holding your fin-
ger(s)
against it for long periods of time.
Doing so may produce some temporary distor-
tion effects on the screen.

15
22
ENGLISH
PreParatIon
■ The TV can be installed in various ways such as
on a wall, or on a desktop etc.
■ The TV is designed to be mounted horizontally.
Power
Supply
Circuit
breaker
earthIng
Ensure that you connect the earth wire to prevent
possible electric shock. If grounding methods are
not possible, have a qualified electrician install a
separate circuit breaker.
Do not try to earth the TV by connecting it to tele-
phone wires, lightening rods or gas pipes.
10 cm
For adequate ventilation allow a clearance of 10
cm all around the TV.
10 cm
10 cm
10 cm
2
■ You should purchase necessary components
to fix the TV safety and secure to the wall on
the market.
■ Position the TV close to the wall to avoid the
possibility of it falling when pushed.
■ The instructions shown below are a safer way
to set up the TV, by fixing it to the wall, avoid-
ing the possibility of it falling forwards if pulled.
This will prevent the TV from falling forward
and causing injury. This will also prevent the
TV from damage. Ensure that children do not
climb or hang from the TV.
3
Use the eye-bolts or TV brackets/bolts to fix the
product to the wall as shown in the picture.
(If your TV has bolts in the eyebolts, loosen then
bolts.)
* Insert the eye-bolts or TV brackets/bolts and
tighten them securely in the upper holes.
Secure the wall brackets with the bolts on the
wall. Match the height of the bracket that is
mounted on the wall.
Use a sturdy rope to tie the product for alignment.
It is safer to tie the rope so it becomes horizontal
between the wall and the product.
2
1
1
1
2
3
note
► When moving the TV undo the cords first.
► Use a platform or cabinet strong and large
enough to support the size and weight of the TV.
► To use the TV safely make sure that the height of
the bracket on the wall and on the TV is the
same.
careful InStallatIon
advIce
deSktoP PedeStal
InStallatIon








 






















16
23
ENGLISH
■ We recommend the use of a LG Brand wall
mounting bracket when mounting the TV to a wall.
■ We recommend that you purchase a wall mount-
ing bracket which supports VESA standard.
■ LG recommends that wall mounting be per-
formed by a qualified professional installer.
10 cm
10 cm
10 cm
10 cm
10 cm
NOTE
►Should Install wall mount on a solid wall per-
pendicular to the floor.
►Should use a special wall mount, if you want
to install it to ceiling or slanted wall.
►The surface that wall mount is to be mount-
ed on should be of sufficient strength to sup-
port the weight of TV set; e.g. concrete, nat-
ural rock, brick and hollow block.
►Installing screw type and length depends on
the wall mount used. Further information,
refer to the instructions included with the
mount.
►LG is not liable for any accidents or damage
to property or TV due to incorrect installa-
tion:
- Where a non-compliant VESA wall mount
is used.
- Incorrect fastening of screws to surface
which may cause TV to fall and cause per-
sonal injury.
- Not following the recommended Installation
method.
AA
BB
Model
VESA
(A
*
B)
Standard
Screw
Quantity
22LD3
**
100
*
100 M4 4
26/32LD3
**
200
*
100 M4 4
32LD4
**
200
*
100 M4 4
37/42/47LD4
**
200
*
200 M6 4
32LD5
**
200
*
100 M4 4
42/46LD5
**
200
*
200 M6 4
52/60LD5
**
400
*
400 M6 4
32LD6
**
200
*
100 M4 4
37/42/47LD6
**
200
*
200 M6 4
55LD6
**
400
*
400 M6 4
22LE5
***
100
*
100 M4 4
26LE5
***
100
*
100 M4 4
32LE5*** 200
*
100 M4 4
37/42/
47LE5
***
200
*
200 M6 4
55/60LE5
***
400
*
400 M6 4
32LE7*** 200
*
100 M4 4
37/42/
47LE7
***
200
*
200 M6 4
55LE7
***
400
*
400 M6 4
42/47LE8
***
200
*
200 M6 4
55LE8
***
400
*
400 M6 4
Wall MOuNT: HOrizONTal
iNsTallaTiON
23
ENGLISH
■ We recommend the use of a LG Brand wall
mounting bracket when mounting the TV to a wall.
■ We recommend that you purchase a wall mount-
ing bracket which supports VESA standard.
■ LG recommends that wall mounting be per-
formed by a qualified professional installer.
10 cm
10 cm
10 cm
10 cm
10 cm
NOTE
►Should Install wall mount on a solid wall per-
pendicular to the floor.
►Should use a special wall mount, if you want
to install it to ceiling or slanted wall.
►The surface that wall mount is to be mount-
ed on should be of sufficient strength to sup-
port the weight of TV set; e.g. concrete, nat-
ural rock, brick and hollow block.
►Installing screw type and length depends on
the wall mount used. Further information,
refer to the instructions included with the
mount.
►LG is not liable for any accidents or damage
to property or TV due to incorrect installa-
tion:
- Where a non-compliant VESA wall mount
is used.
- Incorrect fastening of screws to surface
which may cause TV to fall and cause per-
sonal injury.
- Not following the recommended Installation
method.
AA
BB
Model
VESA
(A
*
B)
Standard
Screw
Quantity
22LD3
**
100
*
100 M4 4
26/32LD3
**
200
*
100 M4 4
32LD4
**
200
*
100 M4 4
37/42/47LD4
**
200
*
200 M6 4
32LD5
**
200
*
100 M4 4
42/46LD5
**
200
*
200 M6 4
52/60LD5
**
400
*
400 M6 4
32LD6
**
200
*
100 M4 4
37/42/47LD6
**
200
*
200 M6 4
55LD6
**
400
*
400 M6 4
22LE5
***
100
*
100 M4 4
26LE5
***
100
*
100 M4 4
32LE5*** 200
*
100 M4 4
37/42/
47LE5
***
200
*
200 M6 4
55/60LE5
***
400
*
400 M6 4
32LE7*** 200
*
100 M4 4
37/42/
47LE7
***
200
*
200 M6 4
55LE7
***
400
*
400 M6 4
42/47LE8
***
200
*
200 M6 4
55LE8
***
400
*
400 M6 4
Wall MOuNT: HOrizONTal
iNsTallaTiON














22
PREPARATION
ENGLISH
WALL MOUNT: HORIZONTAL
INSTALLATION
A
We recommend the use of a LG Brand wall mounting
bracket when mounting the TV to a wall.
A
We recommend that you purchase a wall mounting
bracket which supports VESA standard.
A
LG recommends that wall mounting be performed by a
qualified professional installer.
4 inches
4 inches
4 inches
4 inches
4 inches
NOTE
!
G Should Install wall mount on a solid wall perpendicular to
the floor.
G Should use a special wall mount, if you want to install it to
ceiling or slanted wall.
G The surface that wall mount is to be mounted on should
be of sufficient strength to support the weight of TV set;
e.g. concrete, natural rock, brick and hollow block.
G Installing screw type and length depends on the wall
mount used. Further information, refer to the instructions
included with the mount.
G LG is not liable for any accidents or damage to property or
TV due to incorrect installation:
- Where a non-compliant VESA wall mount is used.
- Incorrect fastening of screws to surface which may cause
TV to fall and cause personal injury.
- Not following the recommended Installation method.
AA
BB
Model
VESA
(A
*
B)
Standard
Screw
Quantity
55LH9***
47LH9***
42LH9***
47LH7***
42LH7***
37LH7***
32LH7***
42LH6***
32LH6***
55LH5***
47LH5***
42LH5***
37LH5***
26LU5***
22LU5***
19LU5***
47LH3***
42LH3***
37LH3***
32LH3***
42LH2***
37LH2***
32LH2***
26LH2***
22LH2***
19LH2***
200
*
200
200
*
200
200
*
200
200
*
200
200
*
200
200
*
200
200
*
10 0
200
*
200
200
*
10 0
200
*
200
200
*
200
200
*
200
200
*
200
200
*
10 0
100
*
10 0
100
*
10 0
200
*
200
200
*
200
200
*
200
200
*
10 0
200
*
200
200
*
200
200
*
10 0
200
*
10 0
100
*
10 0
100
*
10 0
M4
M4
M4
M4
M4
M4
M4
M4
M4
M4
M4
M4
M4
M4
M4
M4
M4
M4
M4
M4
M4
M4
M4
M4
M4
M4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4

16
ENGLISH
PREPARATION
WALL MOUNT: HORIZONTAL
INSTALLATION
A
We recommend the use of a LG Brand wall mounting
bracket when mounting the TV to a wall.
A
We recommend that you purchase a wall mounting
bracket which supports VESA standard.
A
LG recommends that wall mounting be performed
by a qualified professional installer.
10 cm(4 inch)
10 cm(4 inch)
10 cm(4 inch)
10 cm(4 inch)
10 cm(4 inch)
NOTE
!
G Should Install wall mount on a solid wall perpendicular to
the floor.
G Should use a special wall mount, if you want to install it to
ceiling or slanted wall.
G The surface that wall mount is to be mounted on should
be of sufficient strength to support the weight of TV set;
e.g. concrete, natural rock, brick and hollow block.
G Installing screw type and length depends on the wall
mount used. Further information, refer to the instructions
included with the mount.
G LG is not liable for any accidents or damage to property or
TV due to incorrect installation:
- Where a non-compliant VESA wall mount is used.
- Incorrect fastening of screws to surface which may cause
TV to fall and cause personal injury.
- Not following the recommended Installation method.
AC IN
CABLE MANAGEMENT
AA
BB
Model
VESA
(A
*
B)
Standard
Screw
Quantity
19LD3**
22LD3**
26LD3**
32LD3**
32LD4**
42LD4**
100
*
10 0
100
*
10 0
200
*
10 0
200
*
10 0
200
*
10 0
200
*
200
M4
M4
M4
M4
M4
M4
4
4
4
4
4
4
Page is loading ...
18
P
A
G
E
P
123
45
0
6
789
LIST
Q.VIEW
AV MODE INPUTENERGY
SAVING
MARK
FAV
RATIO
MUTE
OK
MENU
Q.MENU
BACK
EXIT
P
A
G
E
P
123
45
0
6
789
LIST
Q.VIEW
AV MODE INPUTENERGY
SAVING
MARK
FAV
RATIO
MUTE
OK
MENU
Q.MENU
BACK
EXIT
CLEAR
VOICE 2
18
ENGLISH
WATCHING TV /PROGRAMME CONTROL
REMOTE CONTROL KEY FUNCTIONS
When using the remote control, aim it at the remote control sensor on the TV.
(
Only 19/22/26/32LD33*)
1
2
3
4
5
6
7
8
(
Except 19/22/26/32LD33*)
1
2
3
4
5
6
7
8
POWER
Switches the TV on from standby or off to standby.
VOLUME UP /DOWN
Adjusts the volume.
MENU
Selects a menu.
Clears all on-screen displays and returns to TV view-
ing from any menu.
THUMBSTICK
(Up/Down/Left/Right)
Allows you to navigate the on-screen menus and
adjust the system settings to your preference.
OK
Accepts your selection or displays the current
mode.
INPUT
External input mode rotate in regular sequence.
Q.VIEW
Returns to the previously viewed programme.
Programme UP/DOWN
Selects a programme.
Q. MENU
Select the desired quick menu source.
1
2
3
4
5
6
7
8
�
Open the battery compartment cover on the back and install the
batteries matching correct polarity (+with +,-with -).
�
Install two 1.5V AAA batteries. Do not mix old or used batteries
with new ones.
�
Close cover.
�
To remove the batteries, perform the installation actions in reverse.
Installing Batteries
33
ENGLISH
P
A
G
E
P
123
45
0
6
789
LIST
Q.VIEW
AV MODE
INPUT
ENERGY
SAVING
MARK
FAV
RATIO
MUTE
SUBTITLE
AD
TV/
RAD
BACK
EXIT
OK
MENU
Q.MENU
GUIDE
INFO i
P
A
G
E
P
123
45
0
6
789
LIST
Q.VIEW
AV MODE
INPUT
ENERGY
SAVING
MARK
FAV
RATIO
MUTE
TV/
RAD
ABC
DEF
GHI
JKL
MNO
PQRS
TUV
WXYZ
CHAR/NUM
DELETE
SUBTITLE
INFO i
BACK
EXIT
OK
MENU
Q.MENU
GUIDE
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
When using the remote control, aim it at the remote control sensor on the TV.
In Analogue TV and some countries, some remote control keys may not work.
REMOTE CONTROL KEY FUNCTIONS
Installing Batteries
■ Open the battery compartment cover on the back and install
the batteries matching correct polarity (+with +,-with -).
■ Install two 1.5V AAA batteries. Do not mix old or used batter-
ies with new ones.
■ Close cover.
■ To remove the batteries, perform the installation actions in
reverse.
1
2
3
4
5
6
7
8
POWER
Switches the TV on from standby or off to
standby.
VOLUME UP/DOWN
Adjusts the volume.
MENU
Selects a menu.
Clears all on-screen displays and returns to
TV viewing from any menu.
THUMBSTICK
(Up/Down/Left/Right)
Allows you to navigate the on-screen
menus and adjust the system settings to
your preference.
OK
Accepts your selection or displays the cur-
rent mode.
INPUT
External input mode rotate in regular
sequence.
Q.VIEW
Returns to the previously viewed pro-
gramme.
Programme UP/DOWN
Selects a programme.
Q.MENU
Select the desired quick menu source.
or
Only 22/26/32LD3**,
32/37/42/47LD4**,
32/42/46/52/60LD55*,
22/26/32/42/47/55LE53**,
32/37/42/47LD8**,
22/26LE6***
Only 32/42/52LD56*,
32/37/42/47/55LD6**,
32/37/42/47/55/60LE55**,
32/37/42/47/55LE7***,
42/47/55LE8***





















 
19
19
ENGLISH
TURNING ON THE TV
Firstly, connect the power cord correctly.
At this stage, the TV switches to standby mode.
In standby mode to turn TV on, press the
r
/ I, INPUT or P
D
or
E
(or P ) button on the TV or
press the POWER, INPUT, P or NUMBER button on the remote control and the TV will switch on.
2
1
Initializing setup
Note:
a. If you close without completing the initial setting, the Initial Setting menu can be displayed again.
b. “Store Demo” mode is only for shop display and not for general customer use.
c. "Home Use” mode is the optimal setting for home environments, and is the TV's default mode.
d. "Store Demo" mode is the optimal setting for store environments. If a user modifies image quality data,
“Store Demo” mode initializes the product to the image quality set by us after a certain period of time.
e. The mode (Home Use, Store Demo) can be changed by executing Mode Setting in the OPTION menu.
If the OSD (On Screen Display) is displayed on the screen after turning on the TV, you can adjust the
L
anguage
,
M
ode Setting
,
A
uto Tuning
.
- When your TV is turned on, you will be able to use its features.
When connecting the USB device
G
It is not possible to use USB function in 19/22/26/32LD33* models.
When you connect a USB device, this pop up menu is displayed, automatically.
“POP UP MENU” will not be displayed while the OSD including Menu is activated.
In USB device, you can not add a new folder or delete the existing folder.
�
Image shown may be somewhat different from your TV.
When removing the USB device
Connect the USB device to the
U
SB IN
jack
on the TV.
Select
P
HOTO LIST
,
M
USIC LIST
or
M
OVIE LIST
.
1
3
USB memory stick
PHOTO LIST MUSIC LIST
Select
E
ject
.
Select the USB device menu before removing the
USB device.
2
1
• This TV Supports on JPEG, MP3 and SD Divx.
MOVIE LIST
3
OK
Q.MENU
2
OK
11
ENGLISH
WATCHING TV / PROGRAMME CONTROL
TURNING ON THE TV
Firstly, connect the power cord correctly.
At this stage, the TV switches to standby mode.
In standby mode to turn TV on, press the
r
/ I, INPUT or P button on the TV or press the
POWER, INPUT, P or NUMBER button on the remote control and the TV will switch on.
2
1
Initializing setup
Note:
a. It will automatically disappear after approx. 40 seconds unless a button is pressed.
b. “In -Store” mode is only for shop display and not for general customer use.
c. "Home” mode is the optimal setting for home environments, and is the TV's default mode.
d. "In-Store" mode is the optimal setting for store environments. If a user modifies image quality data,
“In- Store” mode initializes the product to the image quality set by us after a certain period of time.
e. The mode (Home, In- Store) can be changed by executing Factory Reset in the Option menu.
If the OSD (On Screen Display) is displayed on the screen after turning on the TV, you can adjust the
L
anguage
,
L
ocation, Auto Tuning
.
- When your TV is turned on, you will be able to use its features.
Connect the USB device to the
U
SB IN
jacks on the side of TV.
3
Select
P
HOTO LIST
,
M
USIC LIST
or
M
OVIE LIST
1
USB memory stick
PHOTO LIST MUSIC LIST
2
OK
WHEN CONNECTING THE USB DEVICE
When you connect a USB device, this screen is displayed, automatically.
In USB device, you can not add a new folder or delete the existing folder.
When removing the USB device
MOVIE LIST
Select
U
SB Eject
.
Select the USB EJECT menu before removing the
USB device.
1
Q. MENU
2
OK
• It doesn’t support USB HDD
• This TV Supports on JPEG and MP3.




11
ENGLISH
WATCHING TV / PROGRAMME CONTROL
TURNING ON THE TV
Firstly, connect the power cord correctly.
At this stage, the TV switches to standby mode.
In standby mode to turn TV on, press the
r
/ I, INPUT or P button on the TV or press the
POWER, INPUT, P or NUMBER button on the remote control and the TV will switch on.
2
1
Initializing setup
Note:
a. It will automatically disappear after approx. 40 seconds unless a button is pressed.
b. “In -Store” mode is only for shop display and not for general customer use.
c. "Home” mode is the optimal setting for home environments, and is the TV's default mode.
d. "In-Store" mode is the optimal setting for store environments. If a user modifies image quality data,
“In- Store” mode initializes the product to the image quality set by us after a certain period of time.
e. The mode (Home, In- Store) can be changed by executing Factory Reset in the Option menu.
If the OSD (On Screen Display) is displayed on the screen after turning on the TV, you can adjust the
L
anguage
,
L
ocation, Auto Tuning
.
- When your TV is turned on, you will be able to use its features.
Connect the USB device to the
U
SB IN
jacks on the side of TV.
3
Select
P
HOTO LIST
,
M
USIC LIST
or
M
OVIE LIST
1
USB memory stick
PHOTO LIST MUSIC LIST
2
OK
WHEN CONNECTING THE USB DEVICE
When you connect a USB device, this screen is displayed, automatically.
In USB device, you can not add a new folder or delete the existing folder.
When removing the USB device
MOVIE LIST
Select
U
SB Eject
.
Select the USB EJECT menu before removing the
USB device.
1
Q. MENU
2
OK
• It doesn’t support USB HDD
• This TV Supports on JPEG and MP3.
11
ENGLISH
WATCHING TV / PROGRAMME CONTROL
TURNING ON THE TV
Firstly, connect the power cord correctly.
At this stage, the TV switches to standby mode.
In standby mode to turn TV on, press the
r
/ I, INPUT or P button on the TV or press the
POWER, INPUT, P or NUMBER button on the remote control and the TV will switch on.
2
1
Initializing setup
Note:
a. It will automatically disappear after approx. 40 seconds unless a button is pressed.
b. “In -Store” mode is only for shop display and not for general customer use.
c. "Home” mode is the optimal setting for home environments, and is the TV's default mode.
d. "In-Store" mode is the optimal setting for store environments. If a user modifies image quality data,
“In- Store” mode initializes the product to the image quality set by us after a certain period of time.
e. The mode (Home, In- Store) can be changed by executing Factory Reset in the Option menu.
If the OSD (On Screen Display) is displayed on the screen after turning on the TV, you can adjust the
L
anguage
,
L
ocation, Auto Tuning
.
- When your TV is turned on, you will be able to use its features.
Connect the USB device to the
U
SB IN
jacks on the side of TV.
3
Select
P
HOTO LIST
,
M
USIC LIST
or
M
OVIE LIST
1
USB memory stick
PHOTO LIST MUSIC LIST
2
OK
WHEN CONNECTING THE USB DEVICE
When you connect a USB device, this screen is displayed, automatically.
In USB device, you can not add a new folder or delete the existing folder.
When removing the USB device
MOVIE LIST
Select
U
SB Eject
.
Select the USB EJECT menu before removing the
USB device.
1
Q. MENU
2
OK
• It doesn’t support USB HDD
• This TV Supports on JPEG and MP3.
11
ENGLISH
WATCHING TV / PROGRAMME CONTROL
TURNING ON THE TV
Firstly, connect the power cord correctly.
At this stage, the TV switches to standby mode.
In standby mode to turn TV on, press the
r
/ I, INPUT or P button on the TV or press the
POWER, INPUT, P or NUMBER button on the remote control and the TV will switch on.
2
1
Initializing setup
Note:
a. It will automatically disappear after approx. 40 seconds unless a button is pressed.
b. “In -Store” mode is only for shop display and not for general customer use.
c. "Home” mode is the optimal setting for home environments, and is the TV's default mode.
d. "In-Store" mode is the optimal setting for store environments. If a user modifies image quality data,
“In- Store” mode initializes the product to the image quality set by us after a certain period of time.
e. The mode (Home, In- Store) can be changed by executing Factory Reset in the Option menu.
If the OSD (On Screen Display) is displayed on the screen after turning on the TV, you can adjust the
L
anguage
,
L
ocation, Auto Tuning
.
- When your TV is turned on, you will be able to use its features.
Connect the USB device to the
U
SB IN
jacks on the side of TV.
3
Select
P
HOTO LIST
,
M
USIC LIST
or
M
OVIE LIST
1
USB memory stick
PHOTO LIST MUSIC LIST
2
OK
WHEN CONNECTING THE USB DEVICE
When you connect a USB device, this screen is displayed, automatically.
In USB device, you can not add a new folder or delete the existing folder.
When removing the USB device
MOVIE LIST
Select
U
SB Eject
.
Select the USB EJECT menu before removing the
USB device.
1
Q. MENU
2
OK
• It doesn’t support USB HDD
• This TV Supports on JPEG and MP3.




NOTE :














เมื่อต้องการนำอุปกรณ์ USB ออกจากเครื่องรับโทรทัศน์




20
20
WATCHING TV /PROGRAMME CONTROL
ENGLISH
ON SCREEN MENUS SELECTION AND ADJUSTMENT
�
Image shown may be somewhat different from your TV.
Your TV's OSD (On Screen Display) may differ slightly from that shown in this manual.
SETUP
OPTION
PICTURE
INPUT
AUDIO
TIME
OK
Move
Auto Tuning
Manual Tuning
Programme Edit
SETUP
OK
Move
Aspect Ratio : 16:9
Energy Saving : Off
Picture Mode : Vivid
• Backlight 100
• Contrast 100
• Brightness 50
• Sharpness 70
• Colour 70
PICTURE
E
OK
Move
Auto Volume : Off
Clear Voice ll : Off
•
Level
0
Balance 0
Sound Mode : Standard
• Infinite Sound : Off
• Treble 50
• Bass 50
AUDIO
E
LR
-+
OK
Move
Menu Language : English
Input Label
SIMPLINK : On
Key Lock : Off
Set ID : 1
Power Indicator
Demo Mode : Off
Mode Setting : Home Use
OPTION
E
OK
Move
Clock
Off Time : Off
On Time : Off
Sleep Timer : Off
TIME
USB
Except 19/22/26/32LD33*
or
Only 19/22/26/32LD33*
OK
Move
TV
AV1
AV2
Component
RGB
HDMI1
HDMI2
INPUT
Display each menu.
Select a menu item.
Move to the pop up menu.
1
MENU
3
2
OK
OK
• Press the
MENU/EXIT
button to return to normal TV viewing.
• Press the
BACK
button to move to the previous menu screen.
OK
Move
Photo List
Music List
Movie List
DivX Reg. Code
Deactivation
USB
















21
21
ENGLISH
OK
Move
Auto Tuning
Manual Tuning
Programme Edit
SETUP
Auto Tuning
AUTO PROGRAMME TUNING
Use this to automatically find and store all available programmes.
When you start auto programming, all previously stored service information will be deleted.
• If you wish to keep on auto tuning select
Y
es
using the button. Then, press the OK but-
ton. Otherwise select
N
o
.
Check your antenna connection. The previous channel
information will be updated during Auto Tuning.
Yes No
OK
Move
Auto Tuning
Manual Tuning
Programme Edit
SETUP
Auto Tuning
• Press the
M
ENU/EXIT
button to return to normal TV viewing.
• Press the
B
ACK
button to move to the previous menu screen.
Select
S
ETUP
.
Select
A
uto Tuning
.
Select
Y
es
.
Run
A
uto tuning
.
1
MENU
3
2
OK
OK
4
OK
MAINTENANCE
Early malfunctions can be prevented. Careful and regular cleaning can prolong the life of your new TV.
Caution: Be sure to switch the power off and unplug the power cord before you begin any cleaning.
Cleaning the Screen
A good way to keep the dust off your screen for a while is to wet a soft cloth in a mixture of lukewarm water
and a little fabric softener or dish washing detergent. Wring the cloth until it is almost dry, and then use it
to wipe the screen.
Ensure there is no excess water on the screen. Allow any water or dampness to evaporate before switching on.
Cleaning the Cabinet
A
To remove dirt or dust, wipe the cabinet with a soft, dry, lint-free cloth.
A
Do not to use a wet cloth.
Extended Absence
G
If you expect to leave your TV dormant for prolonged periods (such as a holiday), unplug the power
cord to protect against possible damage from lightning or power surges.
CAUTION
2
1






















22
15
ENGLISH
APPENDIX
TROUBLESHOOTING
The TV does not operate properly.
The remote control
does not work
Power is suddenly
turned off
A
Check to see if there is any object between the TV and the remote control causing
an obstruction. Ensure you are pointing the remote control directly at the TV.
A
Ensure that the batteries are installed with correct polarity (+ to +, - to -).
A
Ensure that the correct remote operating mode is set : TV, STB etc.
A
Install new batteries.
A
Is the sleep timer set?
A
Check the power control settings. Has the Power supply been interrupted.
A
Is Auto sleep activated on this station?
No picture & No sound
No or poor colour
or poor picture
Poor reception on
some channels
Lines or streaks
in pictures
No picture
when connecting HDMI
Horizontal/vertical bars
or picture shaking
Picture appears slowly
after switching on
A
Check whether the TV is switched on.
A
Try another channel. The problem may be with the broadcast.
A
Is the power cord inserted correctly into the mains?
A
Check your antenna direction and/or location.
A
Test the mains outlet by plugging another TV into the same outlet.
A
This is normal, the image is muted during the TV startup process. Please contact
your service centre, if the picture has not appeared after five minutes.
A
Adjust Colour in menu option.
A
Allow a sufficient distance between the TV and the VCR.
A
Try another channel. The problem may be with the broadcast.
A
Are the video cables installed properly?
A
Activate any function to restore the brightness of the picture.
A
Check for local interference such as an electrical appliance or power tool.
A
Station or cable channel experiencing problems, tune to another station.
A
Station signal is weak, reposition the antenna to receive weaker stations.
A
Check for sources of possible interference.
A
Check antenna (Change the position of the antenna).
A
Check HDMI cable over version 1.3.
If the HDMI cables don’t support HDMI version 1.3, it can cause flickers or no
screen display. In this case use the latest cables that support HDMI version 1.3.
The video function does not work.











































23
There is a problem in PC mode. (Only PC mode applied)
A
Adjust resolution, horizontal frequency, or vertical frequency.
A
Check the input source.
A
Use Auto configure or adjust clock, phase, or H/V position. (Option)
A
Check the signal cable.
A
Reinstall the PC video card.
The signal is out of range
(Invalid format)
Screen colour is unstable
or single colour
Vertical bar or stripe on
background &
Horizontal Noise &
Incorrect position
The audio function does not work.
A
Press the
+
or
-
button.
A
Sound muted? Press MUTE button.
A
Try another channel. The problem may be with the broadcast.
A
Are the audio cables installed properly?
A
Adjust
B
alance
in menu option.
A
A change in ambient humidity or temperature may result in an unusual noise
when the TV is switched on or off and does not indicate a fault with the TV.
A
Check HDMI cable over version 1.3.
A
Check USB cable over version 2.0.
Picture OK & No sound
Unusual sound from
inside the TV
No sound when
connecting HDMI
or USB
No output from one
of the speakers
*This feature is not available for all models.
There is a problem with PICTURE settings.
�
It means that the TV is currently set to
I
n Store
mode.
To switch to
H
ome
mode you should do the followings:
From the TV Menu, choose
O
pt ion
->
F
actory Reset
->
Y
es
(wait for a
few seconds for the TV to download again) -> Choose
L
anguage
-> Choose
H
ome
-> Press
O
K
button -> OSD "
W
ELCOME
" appears -> Press
O
K
button.
Program search will begin automatically (You can stop the search by pressing
the
R
ETURN
button). Now you have completed switching to the Home mode.
When the user changes
the picture settings, the
TV automatically
converts back to the
initial settings after a
certain period of time.


































Page is loading ...
Record the model number and serial number of
the TV.
Refer to the label on the back cover and quote
this information to your dealer when requiring
any service.
Model :
Serial No. :
Extended Owner’s Manual that contains
advanced features of these LG TV-sets is
located on CD-ROM in electronic version.
To read it You need to open chosen les by
using Personal Computer (PC) equipped with
CD-ROM drive.
Trade Mark of the DVB Digital Video
Broadcasting Project (1991 to 1996)
(only dtv)








/