Page 1 of 5
BERNINA 750/710 - Firmware Update
Note:
The instructions take you step-by-step through the download and the extraction of the firmware files to an USB
memory stick (FAT32 formatted). These instructions are also valid for further firmware updates – hence, the file
names and illustrations used may be different, depending on the update, the installed operating system and the
used Internet browser.
In this installation manual, illustrations from Windows® 7 and Windows® Internet Explorer 9 are used.
System requirements:
To update the firmware of the BERNINA sewing machine requires:
Computer with Windows® 7 , Windows® 8, Windows® 8.1, Windows® 10 operating system.
System type: 32 Bit or 64 Bit operating system
BERNINA sewing computer
Empty BERNINA USB-Memory key (>256 MB / FAT 32 formatted) ¹
Free USB-Port on Computer side
Internet connection to download the firmware
Step 1: Formatting USB-Stick (FAT32):
Important! USB stick must be FAT32 formatted. If it isn't, the firmware update won't complete
successfully.
The reason is that a FAT16-formatted USB stick won't be able to save more 80 embroidery patterns from the
sewing machine. To avoid data loss for USB stick
capacity reasons, we strongly recommend to always
using a FAT32-formatted memory stick.
There won't be any capacity problems with a
FAT32-formatted USB stick.
WARNING: Formatting will erase ALL data on
this disk.
1.1. How to FAT32- format an USB stick:
a. Plug your USB stick into a free USB port on your
PC.
b. Wait until the stick is ready for operation.
c. Open Windows Explorer.
d. Right-click on the USB sticks drive.
e. Select 'Format' in the pop-up menu."
f. The second window contains information
regarding file system.
If FAT32 appears in the bar, formatting won't
be necessary.
If a different value than FAT32 appears, set
the value to FAT32 and carry out the
formatting.
g. Use to start FAT32 formatting.
WARNING: Formatting will erase ALL data on this
disk.
h. After successful formatting, the USB stick is
ready for the firmware updating of the sewing machine.
Page 2 of 5
Step 2: Download firmware version file
2.1. To start the download process, click on the link: Fehler! Kein
Text mit angegebener Formatvorlage im Dokument.
1
.
2.2. A dialog window will open:
Open the dropdown menu of and
select .
2.3. A dialogue window „saves as…“opens.
Select a directory on the local hard disk (as
example: C:\BERNINA_Downloads), in which the
file will be downloaded.
Confirm the selection with .
2.4. The file will be saved to the selected directory to your Computer. (As example C:\BERNINA_Downloads).
(The time for downloading the file is dependent on the band width of your Internet connection).
2.5. Click on the button.
2.6. Opening the folder:
„Firmware_BERNINA_xxx_Vxxxxxx.zip“.
1
1
The „x“ is standing for a number, the visible numbers show you the firmware versions
Page 3 of 5
Step 3: Extract the firmware files
3.1. Plug on the Computer an empty USB-Memory Stick (min. 256 MB / FAT32 formatted) in one of the free
and available USB-Ports.
3.2. To extract the files, click on the file:
„Firmware_BERNINA_xxx_Vxxxxxx.exe“
1
.
3.3. Confirm the security information with
.
3.4. The self-extracting Zip file starts the following
dialogue:
Select by clicking on the button the drive,
where the empty USB-Memory stick is
connected. (As example drive K :).
3.5. Confirm the selection with .
1
The „x“ is standing for a number, the visible numbers show the firmware versions
Attention: The firmware files may NOT
be unpacked in one on the USB-Memory
stick available subdirectory.
Page 4 of 5
3.6. The files become unpacked to the selected USB-
Memory Stick.
Step 4: Checking the files
4.1. After the extraction, you will find the following four (3) files, in the root of your USB-Memory Stick:
vaxxxxxx_xxxxx_Berninaxxx.bin
1
(Application)
vbxxxxxx_Universalbootloader_Crossover.bin
1
(Bootloader)
xbxxxxxx_xxxxx_Berninaxxx.bin
1
(Application)
vdxxxxxx_Universalbootloader.bin
1
(Bootloader)
(On your files, instead of the letter x will be shown numbers).
Step 5: Update firmware of the BERNINA
5.1. The files are now ready to use for updating your BERNINA sewing machine.
5.2. Connect the USB-Memory Stick to your sewing machine
5.3. Go to the “Setup-Program” of your BERNINA Sewing machine.
5.4. Touch the following 3 buttons on the display
5.5. Touch now the Update button on the left hand side
5.6. The Update procedure will be started and takes some minutes.
Please do not switch off the machine or disconnect the USB-Memory Stick while the update is
running.
Step 6: Checking the firmware version:
6.1. Go to the “Setup-Program” of your BERNINA Sewing machine.
1
The „x“ is standing for a number, the visible numbers show the firmware versions
Page 5 of 5
6.2. Open the “Info- Menu”
6.3. Press the following button on screen
6.4. On the information screen of your BERNINA you will see the following information:
Version Software: Vxx.xx.xx
1
Version data: Vxx.xx.xx
1
Version bootloader: Vxx.xx.xx
1
EMB Appl. version: Vxx.xx.xx
1
(EMB Appl version only shown if the embroidery module is attached).
-
1
-
2
-
3
-
4
-
5
Bernina 710 Operating instructions
- Type
- Operating instructions
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Bernina 570 QE Operating instructions
-
-
-
-
-
-
-
Bernina 700 User manual
-
-
