Bernina 590 E Operating instructions

Brand: Bernina

Model: 590 E

Type: Operating instructions

Bernina 590 E is a computerized sewing machine with a wide range of features to help you create beautiful projects. It offers 80 built-in stitches, including utility, decorative, and heirloom stitches, as well as 7 buttonholes. The machine also features a large sewing area, a built-in needle threader, and an automatic bobbin winder. With its easy-to-use controls and clear LCD display, the Bernina 590 E is perfect for both beginners and experienced sewers.

Instructions for the firmware update

Introduction

These instructions describe how to update the firmware for a BERNINA machine. The file names and figures

used in these instructions may differ depending on the operating system that is installed. The screenshots

shown in these instructions were created on Windows 10.

The following is required for the firmware update:

• PC (Windows 7 or later) with Internet access and USB port

• Empty USB stick (FAT32-formatted)

Please note: The BERNINA USB stick (special accessory) is intended for use with all BERNINA machines that

have a USB port. It is already formatted for FAT32. Many other USB sticks may also work but there is no

guarantee that any particular USB stick will work. BERNINA recommends deleting any data that is saved on

the USB stick before updating, or transferring this data to a different storage medium.

Firmware update on macOS

The firmware update cannot be readily unpacked using the Apple operating system. To load the firmware to

the USB stick anyway, you have two options:

• Use the Windows operating system on a dual-boot system (Boot Camp)

• Use a Windows emulator on the Apple operating system along with appropriate software to unpack the

ZIP files

Preparation

Formatting the USB stick

To ensure that the USB stick works with the BERNINA machine, the USB stick must be formatted in the

FAT32 file system.

Please note: During formatting, all files on the USB stick are irretrievably deleted.

> Insert the USB stick into the PC.

> Open Windows Explorer.

> Right-click on the USB stick and select «Format» from the context menu.

> If «FAT32» has already been selected under «File system», close the window.

– The USB stick is already formatted to FAT32.

> If «FAT32» has not already been selected under «File system», select «FAT32».

BERNINA International AG | CH-8266 Steckborn Switzerland | www.bernina.com | © Copyright by BERNINA International AG

1046975.00A.01

2019-08 EN

Instructions for the firmware update

1046975.00A.01

2019-08 EN

> To format the USB stick, click on the «Start» button.

– Once the formatting is complete, the message «Format Complete» appears.

Downloading the firmware

Please note: The "X" in the sample files stands for the machine and the firmware version.

> Open the Internet browser and enter "http://www.bernina.com/support" in the address bar.

> Click on the «Search support info for models» tab and select the required model.

> To download the file, click on the link «Firmware BERNINA XXX Vxx.xx.xx».

– A dialog window appears.

> Click on the «Save as» button.

Instructions for the firmware update

1046975.00A.01

2019-08 EN

> Select a directory on the local computer where you want to save the file and then click on «Save»,

e.g. ...C:\Downloads.

– The ZIP file is downloaded to the selected directory.

> Once the download is complete, click on the «Open folder» button.

– The folder with the ZIP file opens.

Instructions for the firmware update

1046975.00A.01

2019-08 EN

Unpacking the firmware

Prerequisite:

• The USB stick is formatted to FAT32 and inserted into the PC.

> Right-click on the ZIP file «Firmware_BERNINA_XXX_Vxx.xx.xx.zip» select «Extract All…» from the

context menu.

> If a security warning is displayed, allow the unpacking to continue and do not cancel since, otherwise,

the folder will not be unpacked.

> Check the box for «Show extracted files when complete» and click on the «Extract» button.

– The folder with the unpacked «Firmware_BERNINA_XXX_Vxxxxxx.exe» file opens.

> Double-click on the «Firmware_BERNINA_XXX_Vxxxxxx.exe» file.

– A dialog window opens.

> Click on the «...» button and select the USB stick as the target folder. When doing so, ensure that the

unpacked files are saved directly onto the top level of the USB stick. Please note: For older firmware

files, the «Winzip» program opens instead of «7-Zip». However, the procedure remains the same.

Instructions for the firmware update

1046975.00A.01

2019-08 EN

> To start unpacking, click on the «Unzip» button.

– Three files are saved in the target directory. For older models, there may even be four files.

Update

Carrying out the firmware update

> Insert the USB stick with the new firmware version into the machine.

> Tap «Setup Pogram».

> Tap «Machine settings».

> Tap «Wartung/Update».

UPDATE

> Tap «Firmware update».

> Tap «Save Data».

– The field is marked with a green check.

Update

> To start the firmware update, tap «Start firmware update».

Please note: The update may take several minutes. During the update, do not switch the machine off

and do not remove the USB stick.

– The machine restarts. Once the update is complete, a message appears.

Instructions for the firmware update

1046975.00A.01

2019-08 EN

Entering the serial number (only when requested)

For models from the 7 and 8 Series, you must enter the eight-digit serial number after the firmware update if

this has not already been entered at the factory or during the last update.

> Tap the text field.

> Read off the eight-digit serial number(1) from the rear of the machine and enter this.

> Tap «Confirm» and enter the serial number again.

– The update is complete and the machine restarts.

Bernina 590 E Operating instructions

Bernina 590 E Operating instructions

Bernina 590 E Operating instructions

Related papers

Other documents