Label Picture Description QTY
A Side Panel 2
B Back Support Bar 1
C
Seat
(Labeled with face and
bottom)
1
Label Picture Description QTY
D Bolt:M6*20MM 10
Caution: You must read this before you proceed
Single Chair
E Allen Key 1
F Seat Cushion 1
G Back Cushion 1
Before Beginning Assembly:
Step 1
Take out the silders in the four ends of the Seatboard(C ) using Allen Key(E ).
Step 3
Step 2
Insert the Seat(C) onto the Side Panel(A), as shown in the picture.
Attach Seat(C) and Side Panel(A) using Bolt(D) with Allen Key(E) as shown in the picture.
Loosely tighten the Bolts.
Step 4
Attach Back Support Bar(B) to Side Panel(A) using Bolt(D ) with Allen Key(E).
Loosely tighten the Bolts.
Stand the Chair up.
Put Back Cushion(G) and Seat Cushion(F) on the Chair, and stick the vercro.
Your Single Chair is ready for use.
Step 5
Repeat Step1 to Step 3 to attach the second Side Panel(A).
Place chair upright and test for stability.
Then in a sequential manner, proceed to fully tighten all Bolts at all joints.
Step 6
Label Picture Description QTY
A
Side Panel
1
B
Back Support Bar
1
C
Seat Panel
(Labeled with 'face' and
'bottom')
1
D
Leg Support Bar
1
E
Seat Cushion
2
F
Back Cushion
2
Caution : You must read this before you proceed
Right Sofa
1 OF 8
Label Picture Description QTY
①
Bolt (M6*20MM)
11
②
Allen Key
1
Before
Beginnin
g
Assembly
:
2 OF 8
Step 1
Overview
This Sofa has multiple parts and may require up to 30 minutes to assemble. To give
you an overview of the Sofa parts, the above picture is to help you put the various
parts into perspective. Please read through the instructions below to familiarise
yourself with the parts and steps before assembly.
Open the carton and place all the parts onto a clean, non-marring surface.
Take out the plastic plug ( prevent the alum tube was scratched) in the four ends of the Seat
Board(C) using Allen key (②) as shown above.
FRONT FACING
Leg Support Bar(D)
Side Panel(A)
Back Support Bar(B)
Seat Panel(C)
Seat Cushion(E)
Back Cushion(F)
3 OF 8
Step 2
Step 3
Place the Side Panel(A) with its inside facing up.
Insert Seat Panel(C) into the Side Panel(A).
3.1) Attach the Seat Panel(C) to Side Panel(A) using Bolts(①) with Allen Key(②) as shown
above.
3.2) Attach the Seat Panel(C) to Side Panel(A) using Bolts(①) with Allen Key(②) as shown
above.
Do not fully tighten Bolts.
4 OF 8
Step 4
Step 5
4.1) Remove the plastic plugs( prevent the alum tube was scratched) in the both ends of Back
Support Bar (B) using Allen Key(②) as shown above.
4.2) Insert the Back Support Bar(B) into the Side Panel(A).
Attach the Back Support Bar(B) to the Side Panel(A) using Bolt(①) with Allen Key(②).
Do not fully tighten Bolt.
A
5 OF 8
Step 6
Step 7
Insert the Leg Support Bar(D) into the Back Support Bar(B) and Seat Panel(C) as shown above.
7.1) Attach the Leg Support Bar(D) to Back Support Bar(B) and Seat Panel(C) using Bolts(①) with
Allen Key(②) as shown above.
7.2) Attach the Leg Support Bar(D) to Seat Panel(C) using Bolt(①) with Allen Key(②) as shown
above.
Do not fully tighten Bolts.
6 OF 8
Step 8
Step 9
Stand the Sofa up.
Place the Sofa on a LEVEL SURFACE.
Inspect it and make sure all parts are adequately connected.
Gently and carefully, sit onto to the Sofa.
This will help to align all parts at all the joints.
Then get off the Sofa, and in a sequential manner, proceed to tighten all Bolts.
When tightening the Bolts, tighten sequentially.
DO NOT tighten any Bolt fully and then move on to the next one.
This may cause the frame to warp.
If there are still wobbles, loosen the Bolts and execute the same process.
If the Sofa is not stable it could lead to damage to the product.
Note: This step is done best with the assistance of a second adult.
Put Seat Cushions(E) and Back Cushions(F) on the Sofa and stick the velcro from back cushion to
seat cushion as shown above.
Your Right Sofa is ready for use.
7 OF 8
What is Proposition 65?
Proposition 65 is a California law that requires warning labels on products that may contain one of more than
800-plus chemicals or ingredients that the California Office of Environmental Health Hazard Assessment
(OEHHA) has deemed to cause cancer or other reproductive toxicity. Chemicals and elements on this list
include wood dust, brass, and other everyday substances, which can be found in very common household
items, such as: lamps, tableware, jewelry, crystal glasses, electric cords, beauty products, automobiles, and
furniture.
Why Did I Find a Proposition 65 Warning on My Home Goods Product?
We include Proposition 65 warnings on all of our products because there is always a chance that one of the
800-plus common chemicals and ingredients listed under this law could potentially be on our furniture or
packing materials. We risk large fines under this law, if we don't include this warning.
Should I worry?
We realize you may be worried finding this warning on our products, but we want to reassure you that the
hazardous exposure limits for any of these chemicals have never been found on furniture products that we’ve
shipped to our customers. Additionally, this warning label is very common and can be found on almost every
piece of furniture sold in the state of California.
Just How Common Are Proposition 65 Warnings?
Proposition 65 warnings have become so common in California that it is hard to take a trip to a local bank,
grocery store, or restaurant without finding at least one warning. In fact, even the Disney Land Resort has a
Proposition 65 warning:
Do not clean furniture with harsh cleansers or polish.
Do not put hot items directly on furniture surface
Do not write on furniture without a padded barrier to protect the surface.
To obtain the longest lifespan of your outdoor products, avoid extended and
lengthy exposure to rain, snow, and direct sunshine. Whenever possible cover the
product and /or place under patio or awnings.
To obtain the longest lifespan of your outdoor prodcts, minimizing exposure to direct
sunlight is recommended.
Not for commercial use. For residential use only .
Stains may be removed with mild soap solution and damp cloth.
Dust and pick-up spills using a clean, non-colored, lint-free cloth .
Children should not climb or jump on the furniture.
Label Picture Description QTY
A Left Leg 1
B Right Leg 1
C
Table Top Frame (with
Suction Cups)
1
D Glass Top 1
Label Picture Description QTY
E Bolt:M6*20MM 9
F Allen Key 1
Caution: You must read this before you proceed
Table
Before Beginning Assembly:
Step 1
Take out the silders in the four ends of Table Top Frame(C ) using Allen Key(F).
Step 3
Attach the Table Top Frame(C) to the Right Leg(A) using Bolt(E) and Allen Key(F) as
shown in the picture.
Loosely tighten the Bolts.
Caution: The Table and its Parts are Heavy. Two adults are required for lifting and
moving them.
Step 2
Open the carton and place all the parts on a clean, non-marring surface.
Attach the Table Top Frame(C) to the Left Leg(A) using Bolt(E) and Allen Key(F) as
shown in the picture.
Loosely tighten the Bolts.
Caution: The Table and its Parts are Heavy. Two adults are required for lifting and
moving them.
Step 5
Place the Glass Top(D) on the assembled Table Frame.
Caution: The Table and its Parts are Heavy. Two adults are required for lifting and
moving them.
Your Table is ready for use.
Step 6
Step 4
Stand up the table, check stability and then tighten the bolts.
Note DO NOT fully tighten a BOLT in one go and then move on to the next. Rather,
In a sequential manner, gradually tighten each Bolt until all bolts are evenly
secured. This methodology will ensure maximum evenness once all Bolts are fully
tightened.
/
