FuzzDog Peachy Fuzz Operating instructions

Brand
FuzzDog
Model
Peachy Fuzz
Type
Operating instructions

FuzzDog Peachy Fuzz Below you will find brief product information for FuzzDog Peachy Fuzz. This manual will help you to get the most out of your new effect pedal and provide you with the necessary information to get started. The FuzzDog Peachy Fuzz is a versatile fuzz pedal that can be used to create a wide range of fuzz tones, from subtle overdrive to heavy distortion. The pedal features three controls: Fuzz, Tone, and Volume. The Fuzz control adjusts the amount of fuzz, the Tone control adjusts the brightness of the fuzz, and the Volume control adjusts the overall output level.

FuzzDog Peachy Fuzz Below you will find brief product information for FuzzDog Peachy Fuzz. This manual will help you to get the most out of your new effect pedal and provide you with the necessary information to get started. The FuzzDog Peachy Fuzz is a versatile fuzz pedal that can be used to create a wide range of fuzz tones, from subtle overdrive to heavy distortion. The pedal features three controls: Fuzz, Tone, and Volume. The Fuzz control adjusts the amount of fuzz, the Tone control adjusts the brightness of the fuzz, and the Volume control adjusts the overall output level.

Peachy Fuzz
Frantastically heavy but
smooth fuzz tones
Contents of this document are ©2014 Pedal Parts Ltd.
No reproduction permitted without the express written
permission of Pedal Parts Ltd. All rights reserved.
Schematic
R1 33K
R2 100K
R3 560K* (567K)
R4 33K
R5 33K
R6 8K2* (9K1)
R7 100R
R8 120K
R9 39K* (41K)
R10 10K
R11 10R
R12 2K2 (CLR)
C1 100n
C2 100p
C3 100n
C4 18p
C5 10n
C6 470n
C7 1u
C8 1u
C9 10u elec
C10 100u elec
IC1 TLC2262
IC2 LM386N-1
IC3 LM386N-1
D1 1N4001
FUZZ 10KA
TONE 10KB
VOL 100KB
BOM
*Resistor values marked have been substituted for the original values marked in blue,
which may be awkward to get hold of.
You won’t get the right fuzzy goodness without the right ICs. Note the N-1 suffix on the
LM386. You want these, not the N-3 or N-4 which are higher voltage-rated devices .
PCB Layout ©2014 Pedal Parts Ltd.
The power and signal pads on the PCB conform to
the FuzzDog Direct Connection format, so can be
paired with the appropriate daughterboard for quick
and easy offboard wiring.
Snap the small metal tag off the pots so they can be
mounted flush in the box.
Pots mount on the opposite side of the board to the other components.
The board has been designed to take
vertical-mount pots, but you can wire
in normal ones or use header pins to
attach them.
PCB Layout
1 2 3
Test the board!
UNDER NO CIRCUMSTANCES will troubleshooting help
be offered if you have skipped this stage. No exceptions.
Once you’ve finished the circuit it makes sense to test is before
starting on the switch and LED wiring. It’ll cut down
troubleshooting time in the long run. If the circuit works at this
stage, but it doesn’t once you wire up the switch - guess what?
You’ve probably made a mistake with the switch.
Solder some nice, long lengths of wire to the board connections for
9V, GND, IN and OUT. Connect IN and OUT to the jacks as shown.
Connect all the GNDs together (twist them up and add a small
amount of solder to tack it). Connect the battery + lead to the 9V
wire, same method. Plug in. Go!
If it works, crack on and do your switch wiring. If not... aw man. At
least you know the problem is with the circuit. Find out why, get it
working, THEN worry about the switch etc.
BATTERY
IN OUT
Your nice, new circuit board
INCLUDING WIRED POTS!!!!
IN 9V GND OUT
Wire it up (if using a daughterboard please refer to the relevant document)
Wiring shown above will disconnect the battery when you remove the jack
plug from the input, and also when a DC plug is inserted.
The Board GND connections don’t all have to directly attach to the board. You
can run a couple of wires from the DC connector, one to the board, another to
the IN jack, then daisy chain that over to the OUT jack.
It doesn’t matter how they all connect, as long as they do.
This circuit is standard, Negative GND. Your power supply should be Tip
Negative / Sleeve Positive. That’s the same as your standard pedals (Boss etc),
and you can safely daisy-chain your supply to this pedal.
PedalParts.co.uk
L
E
D
BOARD
OUT
BOARD
9V
BOARD
GND
BOARD
GND
BOARD
GND
BOARD
INPUT
BATTERY
+
IN
OUT
L
E
D
BOARD
GND
BOARD
LED+
+
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5

FuzzDog Peachy Fuzz Operating instructions

Brand
FuzzDog
Model
Peachy Fuzz
Type
Operating instructions

FuzzDog Peachy Fuzz Below you will find brief product information for FuzzDog Peachy Fuzz. This manual will help you to get the most out of your new effect pedal and provide you with the necessary information to get started. The FuzzDog Peachy Fuzz is a versatile fuzz pedal that can be used to create a wide range of fuzz tones, from subtle overdrive to heavy distortion. The pedal features three controls: Fuzz, Tone, and Volume. The Fuzz control adjusts the amount of fuzz, the Tone control adjusts the brightness of the fuzz, and the Volume control adjusts the overall output level.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers