Minka Group P1920-726-L User manual

Type
User manual

Minka Group P1920-726-L is a dimmable LED wall mount fixture. It features a modern design with a glass box and a metal frame. The fixture can be rotated to your suitable position. It comes with all the necessary hardware for installation, including screws, a mounting plate, and a green screw for grounding. The fixture should be installed by a qualified electrician to ensure proper wiring and installation. It is compatible with ELV and/or LED compatible wall dimmer switches.

Minka Group P1920-726-L is a dimmable LED wall mount fixture. It features a modern design with a glass box and a metal frame. The fixture can be rotated to your suitable position. It comes with all the necessary hardware for installation, including screws, a mounting plate, and a green screw for grounding. The fixture should be installed by a qualified electrician to ensure proper wiring and installation. It is compatible with ELV and/or LED compatible wall dimmer switches.

INSTALLATION INSTRUCTIONS FOR P1920-726-L
For
LED
Wall
M
ount Fixture
WA R N I N G ! S H U T P O W E R O F F AT F U S E O R C I R C U I T B R E A K E R .
A V E R T I S S E M E N T ! C O U P E R L E C O U R A N T A U N I V E A U D E S F U S I B L E S O U D O D I S J O N C T E U R
MOUNTING THE FIXTURE (Fig. 1)
1. Shut off power at the fuse box or circuit breaker box. If
necessary, remove the existing fixture and its mounting
hardware.
2. Carefully remove the new fixture from the carton and check
that all parts are included as shown in the illustration.
3. Carefully separate LED box (K) and glass box (G). Place glass
box (G) onto all thread (U) on fixture body (F), add 2pcs spring
washers (H) and hex nut (I) and tighten with tool (T) provided.
(Do not over tighten).
4. Connect plug (J2) and plug (J1) together. Place LED box (K)
on glass box (G). Secure using allen wrench (S) to tighten
screws (L).
5. Attach mounting plate (A) to the junction box (not included)
using mounting screws (C) (Size: 8-32*1/2’’L). The side of the
mounting plate (A) marked “GND” must face out.
CONNECTION THE WIRES (Fig. 2)
6. Connect the electrical wires as shown in Fig.2, making sure
that all wire connectors are secured. If your junction box has a
ground wire (green or bare copper), connect the fixture's
ground wire to it. Otherwise, connect the fixture's ground wire
directly to the mounting plate (A) using the green screw (B)
provided.
FINISHING THE INSTALLATION (Fig. 1)
7. Align canopy (E) onto mounting plate (A) and secure with
screws (D).
8. Rotate glass box (G) to your suitable position. (Please note
that the maximum adjustment angle is 180 degrees)
Your installation is now complete. Return power to the junction box
and test the fixture.
CAUTION /ATTENTION: When handling the fixture, do not apply
pressure to the LEDs. Hold the fixture by the base or fixture body
only.
Replacing LED module (Fig.3)
The LED module can be replaced by a qualified electrician without
cutting the wires and without damaging the decorative element to
which the fixture is attached. See installation steps for more details
(Fig 3.)
Warning: Turn off power at the fuse box or circuit breaker
before replacing the LED module.
a. Shut off the power.
b. Loosen screws (D) and disconnect wire connectors to remove fixture
from wall. (Fig.1)
c. Loosen screws (L) using allen wrench (S). Carefully remove LED box
(K). Disconnect plug (J1) & (J2). Loosen screw (M) and plastic sheet
(N). Remove decorative cover (O). Loosen hex nut (P) and plastic
washer (Q) and carefully remove LED module (R).
d. Reverse steps a-c for installing the new LED module.
Note: The LED module should be provided by a specified supplier.
Fig.1
S
T
A B C D E
L
K
J2
J1
I
H
G
F
Set#:A-021-160115
-Mounting plate
-Green screw
-Mounting screw(2)
-Screw(4)
U
Fig.2
Fig.3
L
K
J2
J1
G
O
N
MRQ
P
S
IMPORTANT: Fixture should be installed by a
qualified electrician to ensure proper wiring and
installation.
Dimmable with ELV and/or LED compatible wall
dimmer switches.
  • Page 1 1

Minka Group P1920-726-L User manual

Type
User manual

Minka Group P1920-726-L is a dimmable LED wall mount fixture. It features a modern design with a glass box and a metal frame. The fixture can be rotated to your suitable position. It comes with all the necessary hardware for installation, including screws, a mounting plate, and a green screw for grounding. The fixture should be installed by a qualified electrician to ensure proper wiring and installation. It is compatible with ELV and/or LED compatible wall dimmer switches.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI