Brinkmann 810-9215-S Operating instructions

Brand: Brinkmann

Model: 810-9215-S

Category: Barbecues & grills

Type: Operating instructions

22 M6 x 12 mm Bolts (Black)

4 #8 Self-Tapping Screws (Black)

2 Wheel Washers

Make sure you have all items listed under PARTS LIST and COMPONENT CARD

CONTENTS before you begin the installation process.

Note: Do not over tighten screws or bolts that come in contact with porcelain-coated surfaces.

COMPONENT CARD CONTAINS:

Qty.

M6 x 12 mm Bolts (Black)

#8 Self-Tapping

Screws (Black)

Wheel Washers

asseMbly InsTruCTIOns:

READ ALL SAFETY WARNINGS & ASSEMBLY INSTRUCTIONS CAREFULLY

BEFORE ASSEMBLING OR OPERATING YOUR GRILL.

WERECOMMENDTWOPEOPLEWORKTOGETHERWHENASSEMBLINGTHISUNIT.

The following tools are required to assemble this Maxre™ Torch 2 Burner Gas Grill:

• Screwdriver

PARTS LIST:

1 Grill Body Assembly

1 Left Side Table

1 Right Side Table

1 Cooking Grate

1 Front Panel

2 Heat Distribution Plates

1 Warming Rack

1 Rear Cart Lower Brace

1 Rear Cart Upper Brace

1 Left Front Cart Leg

1 Left Rear Cart Leg

1 Right Rear Cart Leg

1 Right Front Cart Leg

1 Left Front Leg Cap

1 Left Rear Leg Cap

2 Wheels

 2 WheelAxleBoltsw/CotterPins

1 Carriage Bolt

1 Wing Nut

1 Grease Cup

1 Tank Retension Bracket

1 Left Cart Upper Brace

1 Left Cart Lower Brace

1 Tank Support Bracket

1 Right Cart Brace

1 Tank Brace

Assembly videos for your model grill can be viewed online at:

16 17

FOR COVERS, ACCESSORIES AND OTHER PRODUCTS, PLEASE VISIT US ONLINE AT:

www.MaxFireGrills.com

(Proof of purchase will be required.)

Inspect contents of the box to ensure all parts are included and undamaged.

Choose a good, cleared assembly

area and get a friend to help you

put your grill together. Lay

card board down to protect grill

nish and assembly area.

CAUTION: Some parts may

contain sharp edges.

Wear protective

gloves if necessary.

Step 1

Install left front leg cap onto left

front cart leg.

Step 2

Install left rear leg cap onto left

rear cart leg.

Note: Align the sticker on rear

leg cap with sticker on

rear leg.

Left Front

Cart Leg

Left Rear

Cart Leg

Left Front Leg Cap

Left Rear Leg Cap

Step 3

Attach left cart upper and lower

braces to the left front cart leg and

left rear cart leg using four

M6 x 12 mm bolts (Black) as

illustrated.

Step 4

Attach right cart brace to the right

front and right rear cart legs using

four M6 × 12 mm bolts (Black) as

illustrated.

Left Rear

Cart Leg

Right Rear

Cart Leg

Right Front

Cart Leg

Right Cart

Brace

Left Front

Cart Leg

Left Cart

Upper Brace

Left Cart

Lower Brace

Step5

Attach front panel to front of cart

using four #8 self-tapping screws

(Black). Attach the rear cart upper

and lower braces to the rear cart

legs using eight M6 x 12 mm bolts

(Black) as illustrated.

Step6

To install the tank support bracket

to the right rear and front legs,

insert tabs into slots in the legs

as illustrated.

Note: Install the big end on the

tank support bracket into

the right front cart leg and

the small end on the tank

support bracket to the

right rear cart leg.

Front Panel

Cart Rear

Upper Brace

Cart Rear

Lower Brace

Right Front

Cart leg Right Rear

Cart leg

Tank Support

Bracket

Big

Small

Step7

To install the wheels, insert wheel

axle bolts through wheels and

wheel washers, right rear and

front cart legs and tank support

bracket as illustrated. Insert cotter

pins to secure.

 Note: Orientwheelswithat

side facing legs.

Step 8

Install grill body assembly onto

cart base as illustrated. Secure

using six M6 x 12 mm bolts

(Black).

Cotter Pins

Wheel

Washers Wheel Axle

Bolts

Wheels

Step9

Unscrew the pre-attached bolts

from the tank retention bracket.

Attach tank retention bracket in

between right front and rear cart

legs using the two pre-attached

M6 x 20 mm bolts as illustrated.

Attach the tank brace by inserting

the carriage bolt through the

keyhole, slide down and then

use the wing nut to secure.

Step 10

Attach the left side table assembly

to the left side of grill body. Place

table over bolts and slide toward

back of grill, then tighten bolts

securely.

Step 11

Attach the right side table

assembly to the right side of grill

body. Place table over bolts and

slide toward back of grill, then

tighten bolts securely.

Tank Brace

Bolts

Wing Nut

Carriage Bolt

Step 12

Hang grease cup from brackets on

bottom of grill body.

Step 13

Place the heat distribution plates

on lower level of grill body

assembly, in space on brackets,

directly above burners.

Step 14

Insert warming rack through holes

in grill hood and then insert the

warming rack legs into the holes in

grill body.

Step15

Place cooking grate on support

ribs directly above heat distribution

plates.

Cooking

Grate

Heat

Distribution

Plates

Warming Rack

Grease Cup

Brackets

Maxre™ 9213 (Assembled)

Brinkmann 810-9215-S Operating instructions

Brand: Brinkmann

Model: 810-9215-S

Category: Barbecues & grills

Type: Operating instructions

Download PDF

report

Brinkmann 810-9215-S Operating instructions

Brinkmann 810-9215-S Operating instructions

Related papers

Other documents