Vista VFD4V9CWe Installation Instructions Manual

Vista
Brand
Vista
Model
VFD4V9CWe
Category
Security camera accessories
Type
Installation Instructions Manual

This manual is also suitable for

Read these instructions first!
Vista Varifocal Dome Cameras
Installation Instructions
VFD4V9M Series 1/3 Monochrome Fixed Domes
VFD4V9C Series 1/3 Colour Fixed Domes
2
Vista Varifocal Dome Cameras Installation Instructions
INTRODUCTION
These instructions cover Vista Varifocal Dome cameras. Read all of these instructions. Use
them to install your camera and have them available for its lifetime. If you have any problems,
contact your agent.
3
Installation Instructions Vista Varifocal Dome Cameras
PRODUCT SAFETY
Installation and servicing is only to be carried out by suitably qualified and
experienced personnel.
Do not attempt to disassemble the camera. To prevent electric shock, do not
remove screws or the cover. There are no user-serviceable parts inside. Refer
servicing to qualified service personnel.
Handle the camera with care. Do not abuse the camera. Avoid striking or shaking
it. Improper handling or storage could damage the camera.
Do not expose the camera to rain or moisture, or try to operate in wet areas.
Take immediate action if ever the camera does become wet. Turn the power off
and refer servicing to qualified service personnel. Moisture can damage the
camera and also create the danger of electric shock.
Never face the camera towards the sun. Irrespective of whether the camera is
in use or not, it should never face towards the sun. Use cautiously when operating
the camera in the vicinity of spotlights or other bright lights and light reflecting
objects.
All dome cameras must be powered from a Class 2 power supply unit.
Do not operate the camera beyond its temperature, humidity or power ratings.
Do not use the camera in extreme environments such as high temperature or
humidity.
Do not touch the CCD sensor directly with your fingers. If necessary, use a soft
cloth moistened with alcohol to wipe off any dust.
The Vista Varifocal Dome range is designed for use in general purpose internal CCTV applications
and has no other purpose. Only operate your camera between the temperatures of -10
O
C and
+50
O
C. Do not operate your camera outside its specified power supply range. Vista Varifocal
Dome cameras must only be used in clean, dry, dust-free environments unless housed in a
suitable protective housing to IP65 or better.
ELECTROMAGNETIC COMPATIBILITY (EMC)
This is a class A product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.
This product is intended solely for use in general CCTV applications.
The product must be installed and maintained in accordance with good installation practice
to enable the product to function as intended and to prevent problems. Refer to your agent for
installation guidance.
4
Vista Varifocal Dome Cameras Installation Instructions
MANUFACTURERS DECLARATION OF CONFORMANCE
The manufacturer declares that the equipment supplied with this manual is compliant with the
essential protection requirements of the EMC directive 89/336/EEC and the CE Marking Directive
93/68 EEC. The equipment conforms to the requirements of standards BSEN61000-6-3:2001
for Emissions, BSEN50130-4:1996 (with amendments A1 and A2) for Immunity and
BSEN60950:2002 for Electrical Equipment Safety.
FEATURES
Compact and lightweight design
Integrated 4-9mm Varifocal Direct Drive lens for easy installation and adjustment
High speed f1.6 iris for excellent low light performance
DSP controls for Backlight Compensation and Automatic Gain Control
Manual Pan/Tilt mechanism
Can be wall or ceiling mounted
Video cable with BNC included
2.1mm centre positive power connection
INSTALLATION
Removing the Bubble and Liner
To remove the bubble, remove the locking screw then rotate
the bubble counter clockwise and gently pull the bubble away
from the camera body. The liner can now be removed.
To reattach, first insert the liner over the camera making sure
to align the cut out with the cameras lens. Attach the bubble
by lining up the three tabs on the bubble with the slots in the
camera body. Push the bubble home and gently rotate it
clockwise until it latches into place. Replace the locking screw.
5
Installation Instructions Vista Varifocal Dome Cameras
INSTALLATION
Mounting the Camera
The Vista Varifocal Dome camera can be wall or ceiling mounted. Using the template supplied,
make four holes for the fixing screws, and one hole for the video and power cables. To fix the
camera, it is recommended that the camera assembly is removed from the gimbal in order to
access the fixing holes.
1. Tilt the camera until the pip on the cameras spindle lines up with the cut out on the side of
the gimbal.
2. Gently prise the gimbal side away from the camera cradle until the camera is free.
3. Lift the camera out of the gimbal.
4. The gimbal can now be rotated to line up with the holes in the base.
Use fixings appropriate for the type of wall or ceiling material onto which the camera will be
mounted. Countersunk screws with a diameter of 4 to 5 mm are recommended.
Wall Mounting
If the camera is wall mounted, the camera assembly will need to be rotated 90
O
counter-
clockwise. To do this, remove the camera from the gimbal as described above and after rotating
the camera 90
O
clockwise, insert it back into the gimbal by reversing the removal procedure.
The top of the camera is marked on the camera cradle.
NOTE: If the camera mounting is subsequently changed from WALL to CEILING mount, the
camera assembly will need to be rotated 90
O
clockwise in the gimbal.
6
Vista Varifocal Dome Cameras Installation Instructions
INSTALLATION
Connections
Connect the power to the power connector jack.
Connect the video from the monitor to the Video connector BNC.
Ensure that the power is off before connection.
Check for correct polarity before connection. Improper
polarity may cause damage to the camera.
CONTROLS AND SWITCHES
AGC (Automatic Gain Control)
The Automatic Gain Control facility can improve picture quality when levels of illumination are
low. Select ON or OFF using the dip switch. For most applications, the AGC facility should be ON
and is therefore the default setting.
BLC (Back Light Compensation)
The BLC (Back Light Compensation) facility compensates for back-lit scenes be enhancing
objects in the centre of the scene which would previously have been in silhouette. Select ON
or OFF using the BLC switch. Default is OFF.
Lens Iris Level
Adjust the lens iris level according to the lighting conditions (to achieve video output level of 1V
peak-to-peak).
1. Turn the Automatic Gain Control OFF.
2. Adjust the Lens Level potentiometer. Use care so as not to damage the potentiometer.
3. Turn the Automatic Gain Control switch ON.
NOTE: SWITCHES 3 AND
4 HAVE NO FUNCTION
7
Installation Instructions Vista Varifocal Dome Cameras
ADJUSTMENTS
Camera position
The camera assembly moves in the Tilt direction and can be Panned. Adjust the direction until
the camera is pointing in the desired direction.
Field of View and Focus
Use the levers on the Varifocal lens to set the desired field of view and focus.
FINAL ASSEMBLY
When all the connections and adjustments have been made, reattach the camera liner and
bubble as described earlier.
DIMENSIONS
Vista, Norbain SD Limited
Norbain House, Eskdale Road, Winnersh Triangle, Wokingham, Berkshire RG41 5TS
Norbain SD Limited reserve the right to make changes to the product and
specification of the product from time to time without prior notice
Issue 1 : 03/04 HB-VFD4V9e-1
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Vista VFD4V9CWe Installation Instructions Manual

Vista
Brand
Vista
Model
VFD4V9CWe
Category
Security camera accessories
Type
Installation Instructions Manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents