CMA Dishmachines 180UC Quick Installation Guide

CMA Dishmachines
Brand
CMA Dishmachines
Model
180UC
Type
Quick Installation Guide
RINSE
INJECTION
DETERGENT
INJECTION
WASH
SENSOR
RINSE
SENSOR
5-2019
CMA PN: 10130.02
180UC
Quick Setup
Instructions
1
STEP
FLOOR DRAIN
1"AIR GAP
Connect the drain hose to wall or floor drain. The
floor drain must have a 1 inch air gap between
drain hose and floor drain.
WALL
DRAIN
WARNING: Electrical and plumbing
connections need to be made by a
qualified service technician and
comply with all available Federal,
State and Local Health, Electrical,
Plumbing and Safety codes.
1/2" WATER INLET
DRAIN VALVE
PUMP DRAIN
MOTOR
LEVELING
LEGS
2
3
4
4
Connect dishmachine to hot water source,
recommended minimum temperature
140°F. Unit
will remain in wash cycle until booster heater
temperature reaches
180°F
, then it will advance into
rinse cycle.
3
STEP
When ever possible, remove pump drain if a floor
drain is available near by. Remove drain pipe and
place drain hose on the drain valve and allow
machine to gravity drain.
4
STEP
Level dishmachine by adjusting leveling legs.
Dishmachine must be level front and back and
side to side.
2
STEP
NEUTRAL
HOT
GROUND
DRAIN HOSE
1
HARD WIRE
FOUR WIRE
POWER SUPPLY
180UC REAR VIEW
NOT MORE
THAN 22"
HEIGHT FROM
FLOOR
SUPPORT BRACKET
FOR CHEMICAL
DISPENSER CONDUIT
WASH TEMP 150
O
-160
O
FINAL RINSE TEMP 180
O
-195
O
POWER
OFF
DRAIN
START
CYCLE
ON
DISHMACHINES
6
STEP
FILL
5-2019
180UC
Quick Setup
Instructions
WARNING: Electrical and plumbing
connections need to be made by a
qualified service technician and
comply with all available Federal,
State and Local Health, Electrical,
Plumbing and Safety codes.
The Spirit of Excellence
an Ali Group Company
After filling dishwasher for the first time, (CAUTION:
turn power supply off) reconnect the factory
unplugged wire to booster high-limit switch located
behind front panel.
8
STEP
CMA PN: 10130.02
180UC FRONT VIEW
Turn on power, push Booster Fill Button to fill the Booster Tank on initial start up. Listen for final rinse until water
cascades over scrap trap.
START
ELECTRICAL
BLOCK
5
DRAIN
SCRAP
DRAWER
RINSE
PRESSURE
GAUGE
BOOSTER FILL
BUTTON
6
Chemical dispenser electrical hookup is located
inside control box. Chemical dispenser is optional.
It is not sold with dishmachine.
5
STEP
RINSE
DETERGENT
Turn power switch off and on and the machine will
be filled to correct level in wash tank.
7
STEP
FILL
Turn power supply back on. Allow machine to heat
up (about 5 minutes). Cycle machine by pushing
start switch. Observe “Rinse Cycle” (last 16 seconds
of cycle) must be minimum 180°F. If necessary adjust
the temperature by turning the adjustment stem on
thermostat clockwise to increase.
STEP
9
THERMOSTAT
9
RINSE
TEMPERATURE
DISPLAY
POWER
WASH
TEMPERATURE
DISPLAY
BOOSTER
HIGH LIMIT
SWITCH
8
7
NOTE: To prevent Heating
Element damage, the 180UC
heater must be filled with
water before the heating
element is energized. For
this reason the High Liimit
Switch has intentionally
been disconnected at the
factory and will require
re-connection.
8
  • Page 1 1
  • Page 2 2

CMA Dishmachines 180UC Quick Installation Guide

CMA Dishmachines
Brand
CMA Dishmachines
Model
180UC
Type
Quick Installation Guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents