Copystar CS 308ci User guide

CS 308ci
Copystar
Brand
Copystar
Model
CS 308ci
Type
User guide

This manual is also suitable for

Data Encryption/Overwrite
OPERATION GUIDE
kyoceradocumentsolutions.com
1
Introduction
This function can be used by installing the optional HD-6 / HD-7 (SSD).
This Setup Guide explains the procedures for installing and operating the Data Encryption/Overwrite Functions
(hereinafter called Security Functions) and the procedure for system initialization.
Organization administrators should read and understand this manual.
Instructions for General Users (for Both General Users and Administrators)
• Security Functions ........................................................................ 2
• Touch Panel Display after the Security Functions is Installed....... 3
Instructions for Administrators (for Those in Charge of Installation and Operation of the
Security Functions)
• Installing the Security Functions ................................................... 4
• Changing Security Functions ........................................................ 8
• System Initialization ...................................................................... 9
• Warning Message ....................................................................... 10
• Disposal ...................................................................................... 10
• Appendix..................................................................................... 11
• Nominate a reliable person for the machine administrator when installing the security functions.
• Sufficiently supervise the nominated administrator so that it can observe the security policy and
operation rules at the organization to which it belongs and properly operate the machine in accordance
with the operation guide of the product.
• Sufficiently supervise the general users so that they can operate the machine while observing the
security policy and operation rules at the organization to which they belong.
2
Security Functions
The security functions enables overwriting and encryption.
Overwriting
Multi-functional products (MFPs) temporarily store the data of scanned originals and print jobs, as well as other
data stored by users, in the SSD, and the job is output from that data. Users can also store various types of data
in the SSD. As the data storage area used for such data remains in the SSD as is until it is overwritten by other
data, the data stored here remains restorable using special tools for undesirable use.
The security functions deletes and overwrites (hereinafter collectively referred to as overwrite(s)) the
unnecessary data storage area used for the output data or deleted data to ensure that data cannot be restored.
Overwriting is performed automatically, without user intervention.
CAUTION: When you cancel a job, the machine immediately starts overwriting the data that has been already
stored in the SSD.
Encryption
MFPs store the data of scanned originals and other data stored by users in the SSD. It means the data could
be possibly leaked or tampered with if the SSD is stolen.
The security functions encrypts data before storing it in the SSD. It guarantees higher security because no data
cannot be decoded by ordinary output or operations.
Encryption is automatically performed and no special procedure is required.
CAUTION: Encryption helps enhance security. However, the data stored in the Document Box can be decoded
by ordinary operations. Do not store any strictly confidential data in the Document Box.
Functions of Security Functions
Instructions for General Users (for Both General Users and Administrators)
Security Functions
Print
SSD
Print Jobs
1. Overwrite unneeded area of data.
2. Encryption ( ) / Decoding ( )
3
Touch Panel Display after the Security Functions is Installed
When the security functions has been installed and is running properly, Icon ( ) appears in the touch panel
while unneeded data is being overwritten.
CAUTION: Do not turn the power switch off during overwriting. It may crash the SSD.
NOTE: If you turn the machine off at the power switch during overwriting, data may not be overwritten
completely from the SSD. Turn the machine back on at the power switch. Overwriting automatically resumes.
Document Box.
Box:
㻞㻜㻝㻣㻛㻝㻜㻛㻝㻜㻌㻝㻜㻦㻝㻜
㻞㻜㻝㻣㻛㻝㻜㻛㻝㻜㻌㻝㻝㻦㻝㻝
㻞㻜㻝㻣㻛㻝㻜㻛㻝㻜㻌㻝㻞㻦㻝㻞
㻞㻜㻝㻣㻛㻝㻜㻛㻝㻜㻌㻝㻟㻦㻝㻟
Menu Cancel 㻨㻌㻮㼍㼏㼗 Print
㻞㻜㻝㻣㻝㻜㻝㻜㻝㻜㻝㻜㻠㻡㻜㻝
㻞㻜㻝㻣㻝㻜㻝㻜㻝㻜㻝㻜㻠㻡㻝㻝
㻞㻜㻝㻣㻝㻜㻝㻜㻝㻜㻝㻜㻠㻡㻞㻝
㻞㻜㻝㻣㻝㻜㻝㻜㻝㻜㻝㻜㻠㻡㻟㻝
4
If any kind of problem occurs in the installation or use of the security functions, contact your dealer or service
technician.
Installing the Security Functions
Before Installation
• Make sure that the service representative must be a person who belongs to the supplying company.
• Install the machine in a safe location with controlled access, and unauthorized access to the machine can
be prevented.
• The system will be initialized during installation of the security functions. This means that the data stored in
the SSD will be all overwritten. Special attention should be given if you install the security functions on the
MFP currently used.
• The network to which the machine is hooked up must be protected by a firewall to prevent extraneous
attacks.
• When installing the security functions, change the machine settings as follows.
Installation
Installation of the security function is performed by the service person or the administrator. The service person
or the administrator should log in the system menu to enter the encryption code.
Encryption Code
An encryption code of 8 alphanumeric characters (0 to 9, A to Z, a to z) to encrypt data needs to be entered. By
default, the code is set 00000000.
As an encryption key is then created from this code, it is safe enough to continue using the default code.
CAUTION: Be sure to remember the encryption code you entered. If you need to enter the encryption code
again for some reason and you do not enter the same encryption code, all the data stored on the SSD will be
overwritten as a security precaution.
Instructions for Administrators (for Those in Charge of Installation and
Operations of the Security Functions)
Item Value
User Login/Job Accounting
User Login Setting
Local User
List
Change the administrator password.
System Menu Date/Timer/Energy Saver Date/Time Set the date and time.
5
Installation Procedure
Use the procedure below to select the interface.
1 Press the [System Menu/Counter] key.
2 Press [ ] and [System/Network].
If user login is disabled, the user authentication
screen appears. Enter your login user name and
password and then press [Login]. For this, you
need to log in with administrator privileges. Refer to
the machine's Operation Guide for the default
loginuser name and password.
3 Press [ ] and [Optional Function].
4 The optional function screen is displayed. Select
[Data Encr./Overwrite] and press [Activate].
5 This function will be activated. The data saved in
the large capacity storage will be deleted and the
storage will be formatted and encrypted. If there is
no problem, press [Yes].
6 Turn the power switch on again following to the
indication in the panel screen. The screen for
entering the encryption code is displayed.
7 Enter the encryption code, and press [OK]. Hard
disk/SSD formatting begins.
8 When formatting finishes, follow the on screen
instructions to turn the Power Switch off and on
again.
9 After the opening screen is displayed, confirm that
a hard disk icon (Overwritten completion icon of
unnecessary data in the hard disk) is shown in the
lower right corner of the screen.

(QFU\SWLRQ&RGH
.H\ERDUG
(QWHUWKHHQFU\SWLRQFRGH
1RWH3OHDVHQHYHUIRUJHWWKHHQFU\SWHGFRGH\RX
HQWHUHG,I\RXQHHGWRHQWHUWKHFRGHDJDLQ
LI\RXFDQQRWHQWHUWKHVDPHFRGHWKHGDWDZLOOEH
GHOHWHGIRUVHFXULW\UHDVRQV
2.
6
After Installation
Change the machine setting as follows to securely operate it. If the system in the machine is initialized, it returns
to the settings before installation, so make changes in the same way. If you allow service personnel to conduct
maintenance operations, confirm the set values.
Items changed in Command Center RX
Item Value
Device
Settings
Energy
Saver/Timer
Energy Saver/Timer Settings Timer
Settings
Auto Panel
Reset
On
Panel
Reset Timer
Setting any value
Function
Settings
Printer Printer
Settings
Google Cloud
Print Settings
(Select
[Settings])
Privet(Cloud
Device Local
Discovery
Protocol and
API)
Local
Discovery
Off
Local Print Off
Forwarding Forward Settings Forward
Setting any value
Network
Settings
TCP/IP TCP/IP Settings
Bonjour Settings
Bonjour Off
IPSec Settings
IPSec On
Protocol Protocol Settings Print
Protocols
NetBEUI Off
LPD Off
FTP Server
(Reception)
Off
IPP Off
IPP over SSL
On
IPP
Authentication
Off
Raw Off
WSD Print Off
POP3
(E-mail RX)
Off
Send
Protocols
SMTP
(E-mail TX)
On
FTP Client
(Transmission)
On
SMB Off
WSD Scan Off
eSCL Off
eSCL over
SSL
Off
Other
Protocols
SNMPv1/v2c Off
SNMPv3 Off
HTTP Off
HTTPS On
Enhanced
WSD
Off
Enhanced
WSD over
SSL
On
LDAP Off
IEEE802.1X Off
LLTD Off
REST Off
REST over
SSL
Off
7
Items changed on the machine
For the procedures for changing the settings, refer to the machine OPERATION GUIDE and Command Center
RX User Guide.
After installing the security functions, you can change the security password.
Refer to page 8 for the procedures.
The administrator of the machine should periodically store the histories, and check each history to make sure
there was no unauthorized access or abnormal operation.
Grant regular users permission based on your company rules, and promptly delete any user accounts that stop
being used due to retirement or other reasons.
Security
Settings
Device
Security
Device
Security
Settings
Edit Restriction
Address
Book
Administrator
Only
One Touch
Key
Administrator
Only
Authentication
Security
Settings
User Account
Lockout
Settings
Lockout
Policy
On
Network
Security
Network
Security
Settings
Secure
Protocol
Settings
SSL On
Serverside
Settings
TLS Version
SSL3.0/TLS1.0:
Disable
TLS1.1: Disable
TLS1.2: Enable
HTTP Security
Secure Only
(HTTPS)
IPP Security
Secure Only
(IPPS)
Clientside
Settings
TLS Version
SSL3.0/TLS1.0:
Disable
TLS1.1: Disable
TLS1.2: Enable
Certificate
Verification
On
Management
Settings
Authentication
Settings Authentication
Settings
General Authentication Local
Authentication
Local
Authorization
Settings
Local
Authorization
On
Guest
Authorization
Settings
Guest
Authorization
Off
Simple Login
Settings
Simple Login
Off
History
Settings
History Settings
Job Log History
Recipient
E-mail Address
E-mail Address for
the administrator
of the machine
Auto Sending
On
Item Value
System Menu System/Network Security Level Very High
Internet Internet Browser Off
Item Value
8
Changing Security Functions
Changing Security Password
You can customize the security password so that only the administrator can use the security functions.
1 Press the [System Menu/Counter] key.
2 Press [ ] and [System/Network].
3 If user login is disabled, the user authentication
screen appears. Enter your login user name and
password and then press [Login]. For this, you
need to log in with administrator privileges. Refer to
the machine's Operation Guide for the default login
user name and password.
4 Press [ ], [Data Security] and [SSD Initialization].
5 Enter the security password, and press [OK]. The
initial setting for the Security Password is "000000".
6 Press [Security Password].
7 Enter a new security password 6 alphanumeric
characters and symbols, and press [Next].
CAUTION: Avoid any easy-to-guess numbers for the
security password (e.g. 111111 or 123456).
8 Enter the same password again.
9 Press [OK].
Security Password
10:10System Menu/Counter.
System Initialization
< Back
1/1
System/Network - SSD Initialization
9
System Initialization
Overwrite all the data stored in the SSD when disposing of the machine.
CAUTION: If you accidentally turn the power switch off during initialization, the SSD might possibly crash or
initialization might fail
NOTE: If you accidentally turn the power switch off during initialization, turn the power switch on again.
Initialization automatically restarts.
1 Press the [System Menu/Counter] key.
2 Press [ ] and [System/Network].
3 If user login is disabled, the user authentication
screen appears. Enter your login user name and
password and then press [Login]. For this, you
need to log in with administrator privileges. Refer to
the machine's Operation Guide for the default login
user name and password.
4 Press [ ], [Data Security] and [SSD Initialization].
5 Enter the security password, and press [OK]. The
initial setting for the Security Password is "000000".
6 Press [System Initialization].
7 Press [Start] on the screen to confirm the
initialization. Initialization starts.
8 When the screen appears to show initialization is
completed, check that the memory indicator is OFF,
and turn the power switch off and then on.
Security Password
10:10System Menu/Counter.
System Initialization
< Back
1/1
System/Network - SSD Initialization
10
Warning Message
If the encryption code information of the machine has been lost for some reason, the screen shown here appears
when the power is turned on.
Follow the steps below.
1 Enter the encryption code that was entered during
the installation of the security functions.
CAUTION: Even though entering a different
encryption code can also enable continuation of a job,
this will overwrite all the data stored in the SSD.
Exercise extreme caution when entering an encryption
code.
The encryption code is not the same as the security
password.
2 Press [OK].
3 Confirm that the memory indicator is off. After that,
turn the power switch off and on.
Disposal
If the machine is unused and demolished, initialize the system of this product to erase the SSD data.
If the machine is unused and demolished, obtain directions for disposal from the dealer (from which you
purchased the machine) or your service representative.
10:10
Keyboard
Encryption Code
OK
00000000
11
Appendix
List of factory default settings
The default settings for security mode are shown below.
Items changed in Command Center RX
Item Value
Device Settings
Energy
Saver/Timer
Energy Saver/Timer Settings Timer
Settings
Auto Panel
Reset
On
Panel
Reset Timer
90 seconds
Function
Settings
Printer Printer
Settings
Google Cloud
Print Settings
(Select
[Settings])
Privet(Cloud
Device Local
Discovery
Protocol and
API)
Local
Discovery
On
Local Print
Setting any
value
Forwarding Forward Settings Forward On
Network
Settings
TCP/IP TCP/IP Settings
Bonjour Settings
Bonjour On
IPSec Settings
IPSec Off
12
Network
Settings
Protocol Protocol Settings Print
Protocols
NetBEUI On
LPD On
FTP Server
(Reception)
On
IPP Off
IPP over
SSL
On
IPP
Authentication
Off
Raw On
WSD Print
On
POP3
(E-mail RX)
Off
Send
Protocols
SMTP
(E-mail TX)
Off
FTP Client
(Transmission)
On
SMB
On
WSD Scan Off
eSCL
On
eSCL over SSL
On
Other
Protocols
SNMPv1/v2c On
SNMPv3 Off
HTTP On
HTTPS On
Enhanced
WSD
On
Enhanced
WSD over
SSL
On
LDAP Off
IEEE802.1X Off
LLTD On
REST On
REST over
SSL
On
Security
Settings
Device
Security
Device
Security
Settings
Edit Restriction
Address
Book
Off
One Touch
Key
Off
Authentication
Security
Settings
User Account
Lockout
Settings
Lockout
Policy
Off
Item Value
13
Items changed on the machine
Security
Settings
Network
Security
Network
Security
Settings
Secure
Protocol
Settings
SSL On
Serverside
Settings
TLS Version
SSL3.0/TLS1.0:
Enable
TLS1.1: Enable
TLS1.2: Enable
HTTP Security
Secure Only
(HTTPS)
IPP Security
Secure Only
(IPPS)
Clientside
Settings
TLS Version
SSL3.0/TLS1.0:
Enable
TLS1.1: Disable
TLS1.2: Disable
Certificate
Verification
On
Management
Settings
Authentication
Settings Authentication
Settings
General Authentication
Off
Local
Authorization
Settings
Local
Authorization
Off
Guest
Authorization
Settings
Guest
Authorization
Off
Simple Login
Settings
Simple Login
Off
History
Settings
History Settings
Job Log History
Recipient
E-mail Address
No setting
Auto Sending
Off
Item Value
System Menu System/Network Security Level High
Internet Internet Browser Off
Item Value
2019.3
3MS2WLKDEN0
is a trademark of KYOCERA Corporation
© 2019 KYOCERA Document Solutions Inc.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15

Copystar CS 308ci User guide

CS 308ci
Copystar
Brand
Copystar
Model
CS 308ci
Type
User guide
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents