Data Security Kit(E)
OPERATION GUIDE
1
Introduction
This Setup Guide explains the procedures for installing and operating the optional Data Security Kit (E)
(hereinafter called Security Kit) and the procedure for system initialization.
Organization administrators should read and understand this manual.
Instructions for General Users (for Both General Users and Administrators)
• Security Kit Functions ......................................................2
• Touch Panel Display after the Security Kit is Installed .....4
Instructions for Administrators (for Those in Charge of Installation and Operation of the
Security Kit)
• Installing the Security Kit..................................................5
• Changing Security Functions .........................................10
• System Initialization .......................................................12
• Warning Message ..........................................................13
• Disposal .........................................................................13
• Appendix........................................................................14
• Nominate a reliable person for the machine administrator when installing the security kit.
• Sufficiently supervise the nominated administrator so that it can observe the security policy and
operation rules at the organization to which it belongs and properly operate the machine in accordance
with the operation guide of the product.
• Sufficiently supervise the general users so that they can operate the machine while observing the
security policy and operation rules at the organization to which they belong.
2
Security Kit Functions
The security kit enables overwriting and encryption.
NOTE: If you install the security kit, Running security function... appears when the machine starts up and it
may take a while.
Overwriting
Multi-functional products (MFPs) temporarily store the data of scanned originals and print jobs, as well as other
data stored by users, on the hard disk/SSD and the job is output from that data. As the data storage areas used
for such data remain unchanged on the hard disk/SSD until they are overwritten by other data, the data stored
in these areas is potentially restorable using special tools.
The security kit deletes and overwrites (hereinafter collectively referred to as overwrite(s)) the unnecessary data
storage area used for the output data or deleted data to ensure that data cannot be restored.
Overwriting is performed automatically, without user intervention.
CAUTION: When you cancel a job, the machine immediately starts overwriting the data that was stored on the
hard disk/SSD.
Overwrite Methods
Changing the data overwrite method is available, when a hard disk is installed. There are two overwrite methods,
which can be switched at any time.
Once Overwrite Method
This function overwrites unneeded data areas (in the case of overwriting) or all areas (in the case of system
initialization) with zeroes to prevent data restoration.
3-time Overwrite (DoD) Method (default)
This overwrite method complies with U.S. Department of Defense (DoD) standards, and overwrites unneeded
data areas of the hard disk (in the case of overwriting) or all areas (in the case of system initialization) with
specific characters, their complements, and random characters to prevent data restoration. Data restoration is
not possible even when sophisticated restoration techniques are used, and a higher level of security than Once
Overwrite is obtained.
This method may take more time than Once Overwrite method to process a larger amount of data.
NOTE: For SSD, the method used is Once Overwrite.
Instructions for General Users (for Both General Users and Administrators)
3
Encryption
MFPs store the data of scanned originals and other data stored by users in the hard disk. It means the data could
be possibly leaked or tampered with if the hard disk/SSD is stolen.
The security kit encrypts data before storing it in the hard disk/SSD. It guarantees higher security because no
data cannot be decoded by ordinary output or operations.
Encryption is automatically performed and no special procedure is required.
CAUTION: Encryption helps enhance security. However, the data stored in the Document Box can be decoded
by ordinary operations. Do not store any strictly confidential data in the Document Box.
Functions of Security Kit
If the security kit is introduced while the hard disk and SSD are installed in the machine, the destination where
data received by FAX is to be saved is changed from SSD to hard disk. If you want to change the destination to
SSD, contact your dealer or service technician.
Security Kit
Printing
Faxing
Copying
Send
Send
Print
Sending
Save original data
and various settings
1. Overwrite unwanted area of data.
2. Encryption ( ) / Decoding ( )
Hard disk/SSD
4
Touch Panel Display after the Security Kit is Installed
Hard Disk Icon Display
In Security Mode, the security kit has been properly
installed and is running. The hard disk icon appears on
the lower right side of the touch panel in Security Mode.
NOTE: If the hard disk icon does not appear on the
normal screen, it is possible that the Security Mode is
not ON. Call service.
The hard disk icon display changes as follows during overwriting
The table below shows the icons displayed and their descriptions.
CAUTION: Do not turn the power switch off while is displayed. Risk of damage to the hard disk/SSD.
NOTE: If you turn the machine off at the power switch during overwriting, data may not be overwritten
completely from the hard disk. Turn the machine back on at the power switch. Overwriting automatically
resumes. If you accidentally turn the main power switch off during overwriting or initialization, the hard disk icon
might not switch to the second icon shown above. This would be caused by a possible crash or failed
overwriting of the data to be overwritten. This will not affect subsequent overwriting processes. However, hard
disk initialization is recommended so as to return to normal stable operations. (Initialization should be
performed by the administrator following the steps in System Initialization on page 12.)
Status
Logout
Copy
Send Custom Box
Job Box
Removable
Memory
Select the function.
Admin
FAX
Internet Browser
FAX Box
ProgramSystem
Menu
Paper
Settings
Status/
Job Cancel
Device
Information
Language HelpWi-Fi Direct
2016/02/02 10:10
MM0101_01bar_02
Icon displayed Description
There is unneeded data on the hard
disk/SSD.
Overwriting the unwanted data
The unwanted data is overwritten.
5
If any kind of problem occurs in the installation or use of the security kit, contact your dealer or service technician.
Installing the Security Kit
The Security Kit Contents
The security kit package includes:
• License Certificate
• Installation Guide (for service personnel)
Before Installation
• Make sure that the service representative must be a person who belongs to the supplying company.
• Install the machine in a safe location with controlled access, and unauthorized access to the machine can
be prevented.
• The hard disk/SSD will be initialized during installation of the security kit. This means that the data stored in
the hard disk will be all overwritten. Special attention should be given if you install the security kit on the
MFP currently used.
• The network to which the machine is hooked up must be protected by a firewall to prevent extraneous
attacks.
• The Repeat Copy function will be unavailable after the installation.
• [Adjustment/Maintenance] -> [System Initialization] will not be displayed in the System Menu after the
installation.
• When installing the security kit, change the machine settings as follows.
• If the security kit is introduced while the hard disk and SSD are installed in the machine, the destination
where data received by FAX is to be saved is changed from SSD to hard disk. If you want to change the
destination to SSD, contact your dealer or service technician.
Installation
Installation of the security kit should be performed by the service personnel. The administrator should log in the
system menu to enter the encryption code under the supervision of the service representative.
Encryption Code
An encryption code of 8 alphanumeric characters (0 to 9, A to Z, a to z) to encrypt data needs to be entered. By
default, the code is set 00000000.
As an encryption key is then created from this code, it is safe enough to continue using the default code.
CAUTION: Be sure to remember and securely manage the encryption code you entered. If you need to enter
the encryption code again for some reason and you do not enter the same encryption code, all the data stored
on the hard disk/SDD will be overwritten as a security precaution.
Instructions for Administrators (for Those in Charge of Installation and
Operations of the Security Kit)
Item Value
User Login/Job Accounting
User Login Setting
Local User
List
Change the administrator password.
System Menu Date/Timer/Energy Saver Date/Time Set the date and time.
6
After Installation
Change the machine setting as follows to securely operate it. If the system in the machine is initialized, it returns
to the settings before installation, so make changes in the same way. If you allow service personnel to conduct
maintenance operations, confirm the set values.
Items changed in Command Center RX
Item Value
Device
Settings
Energy
Saver/Timer
Energy Saver/Timer
Settings
Timer
Settings
Auto Panel
Reset
On
Panel
Reset Timer
Setting any
value
Function
Settings
Printer Printer Settings
General Remote
Printing
Prohibit
FAX/i-FAX FAX/i-FAX
Settings
Fax Settings
Remote
Settings
FAX Remote
Diagnostics
Off
RX/Forward
Rules
Settings RX/Forward
Rules
Settings
RX/Forward
Rules
[Use Rule for
Specific RX] or
[Rule for All RX]
Forward
Settings
Forwarding On
Forward
Destination
Any forwarding
destination
Network
Settings
TCP/IP TCP/IP Settings
Bonjour Settings
Bonjour Off
Protocol Protocol Settings Print
Protocols
NetBEUI Off
LPD Off
FTP Server
(Reception)
Off
IPP Off
IPP over
SSL
On
Raw Off
WSD Print Off
POP3
(E-mail RX)
Off
Send
Protocols
SMTP
(E-mail TX)
On
SMTP
Security
STARTTLS or
SSL/TLS
FTP
Encryption TX
On
SMB Off
WSD Scan Off
DSM Scan Off
eSCL Off
eSCL over SSL
Off
Other
Protocols
SNMPv1/v2c Off
SNMPv3 Off
HTTPS Off
Enhanced
WSD
Off
LDAP Off
IEEE802.1X Off
LLTD On
7
Security
Settings
Device
Security
Device
Security
Settings
Authentication
Security
Settings
Password
Policy
Settings
Password
Policy
On
Maximum
password
age
Setting any
value
Minimum
password
length
On
8 or more
characters
Password
complexity
Setting any
value
User Account
Lockout
Settings
Lockout
Policy
On
Number of
Retries until
Locked
Setting any
value
Lockout
Duration
Setting any
value
Lockout
Targe t
All
Network
Security
Network
Security
Settings
Secure
Protocol
Settings
SSL On
Serverside
Settings
TLS Version SSL3.0/TLS1.0:
Disable
TLS1.1: Disable
TLS1.2: Enable
HTTP
Security
Secure Only
(HTTPS)
IPP Security Secure Only
(IPPS)
Clientside
Settings
TLS Version SSL3.0/TLS1.0:
Disable
TLS1.1: Disable
TLS1.2: Enable
Certificate
Verification
On
Item Value
8
Management
Settings
Authentication
Settings Authentication
Settings
General Authentication Local
Authentication
Local
Authorization
Settings
Local
Authorization
On
Guest
Authorization
Settings
Guest
Authorization
Off
Simple Login
Settings
Simple Login
Off
History
Settings
History Settings
Job Log History
Recipient
E-mail Address
E-mail Address for
the administrator
of the machine
Auto Sending
On
Login History
Settings
Login History
On
Recipient
E-mail Address
E-mail Address for
the administrator
of the machine
Auto Sending
On
Device Log
History Settings
Device Log
History
On
Recipient
E-mail Address
E-mail Address for
the administrator
of the machine
Auto Sending
On
Secure
Communication
Error Log
History Settings
Secure
Communicatio
n Error Log
History
On
Recipient
E-mail Address
E-mail Address for
the administrator
of the machine
Auto Sending
On
Item Value
9
Items changed on the machine
For the procedures for changing the settings, refer to the machine OPERATION GUIDE and Command Center
RX User Guide.
After changing the settings, run [Software verification] in the system menu to verify that the machine operates
correctly. Periodically perform [Software verification] after installation as well.
After installing the security kit, you can change the security password as well as the method for overwriting the
entire hard disk.
Refer to page 10 for the procedures.
The administrator of the machine should periodically store the histories, and check each history to make sure
there was no unauthorized access or abnormal operation.
Grant regular users permission based on your company rules, and promptly delete any user accounts that stop
being used due to retirement or other reasons.
Item Value
System Menu System/Network Security Level Very High
Internet Internet Browser Off
10
Changing Security Functions
Changing Security Password
Enter the security password to change security functions. You can customize the security password so that only
the administrator can use the security kit.
Use the procedure below to change the security password.
1 Select the [System Menu/Counter] key.
2 Select [System/Network].
3 If user login is disabled, the user authentication
screen appears. Enter your login user name and
password and then select [Login]. For this, you
need to log in with administrator privileges. Refer to
the machine's Operation Guide for the default login
user name and password.
4 Select [Next] of Data Security.
5 Select [Next] of Hard Disk Initialization.
NOTE: When a hard disk is not installed, ”SSD
Initialization” is displayed. When a hard disk and an
SSD are installed, "Hard Disk/SSD Initialization" is
displayed.
6 Enter the default security password, 000000.
7 Select [Change] of Security Password.
8 Select [Password] to enter a new security
password 6 to 16 alphanumeric characters and
symbols.
CAUTION: Avoid any easy-to-guess numbers for the
security password (e.g. 11111111 or 12345678).
9 Select [Confirm Password] to enter the same
password again.
10 Select [OK].
Cancel OK
Set password.
Enter new password, then re-enter it to confirm.
10/10/2015 10:10
m030908
Password
Confirm
Password
# Keys
# Keys
System/Network - Security Password
11
Changing the Data Overwrite Method
The method used to overwrite data can be changed. Refer to Overwriting on page 2 for details. Changing the
data overwrite method is not available, when a hard disk is not installed.
NOTE: The overwrite methods are used both for overwriting and hard disk initialization, and cannot therefore
be set individually.
Use the procedure below to select the interface.
1 Select the [System Menu/Counter] key.
2 Select [System/Network].
3 If user login is disabled, the user authentication
screen appears. Enter your login user name and
password and then select [Login]. For this, you
need to log in with administrator privileges. Refer to
the machine's Operation Guide for the default login
user name and password.
4 Select [Next] of Data Security.
5 Select [Next] of Hard Disk Initialization.
6 Enter the security password. By default, the code is
set 000000.
7 Select [Change] of Data Overwrite Method.
8 Select [3-time Overwrite (DoD)] (default) or
[Once Overwrite].
9 Select [OK].
Cancel OK
Select data overwrite method.
10/10/2015 10:10
m030241
Once
Overwrite
3-time Over-
write (DoD)
System/Network - Data Overwrite Method
12
System Initialization
Overwrite all the data stored in the hard disk/SSD when disposing of the machine.
CAUTION: If you accidentally turn the power switch off during initialization, the system might possibly crash or
initialization might fail.
NOTE: If you accidentally turn the power switch off during initialization, turn the power switch on again.
Initialization automatically restarts.
Use the procedure below to initialize the system.
1 Select the [System Menu/Counter] key.
2 Select [System/Network].
3 If the user authentication screen appears, enter the
login user name and login password, and select
[Login].
For this, you need to log in with administrator
privileges. If the user authentication screen does
not appear, go to Step 4.
4 Select [Next] of Data Security.
5 Select [Next] of Hard Disk Initialization.
NOTE: When a hard disk is not installed, ”SSD
Initialization” is displayed. When a hard disk and an
SSD are installed, "Hard Disk/SSD Initialization" is
displayed.
6 Enter the default security password, 000000.
7 Select [Execute] of System Initialization.
8 Select [Yes] on the screen to confirm the
initialization. Initialization starts.
9 When the screen appears to show initialization is
completed, turn the power switch off and then on.
Close
Data Overwrite Method:
10/10/2015 10:10
m0201112
System/Network - Hard Disk Initialization
Once Overwrite Method
Security Password:
**********
System Initialization:
Change Change
Start
13
Warning Message
If the encryption code information of the machine has been lost for some reason, the screen shown here appears
when the power is turned on.
Follow the steps below.
1 Select [Encryption Code], and enter the encryption
code that was entered during the installation of the
security kit.
CAUTION: Even though entering a different
encryption code can also enable continuation of a job,
this will overwrite all the data stored in the hard disk/
SSD. Exercise extreme caution when entering an
encryption code.
The encryption code is not the same as the security
password.
2 Turn the power switch off and on.
Disposal
If the machine is unused and demolished, perform Data Sanitization to erase the hard disk/SSD data.
Refer to "Data Sanitization" of "Data Security" in Chapter 8 of the machine's Operation Guide.
If the machine is unused and demolished, obtain directions for disposal from the dealer (from which you
purchased the machine) or your service representative.
OK
Enter the encryption code.
10/10/2015 10:10
av0201
Once
Overwrite
Encryption
Code
14
Appendix
List of factory default settings
The default settings for security mode are shown below.
Items changed in Command Center RX
Item Value
Device
Settings
Energy
Saver/Timer
Energy Saver/Timer
Settings
Timer
Settings
Auto Panel
Reset
On
Panel
Reset Timer
90 seconds
Function
Settings
Printer Printer Settings
General Remote
Printing
Permit
FAX/i-FAX FAX/i-FAX
Settings
Fax Settings
Remote
Settings
FAX Remote
Diagnostics
Off
RX/Forward
Rules
Settings RX/Forward
Rules
Settings
RX/Forward
Rules
Off
Forward
Settings
Forwarding Off
Forward
Destination
No setting
Network
Settings
TCP/IP TCP/IP Settings
Bonjour Settings
Bonjour On
Protocol Protocol Settings Print
Protocols
NetBEUI On
LPD On
FTP Server
(Reception)
On
IPP Off
IPP over
SSL
On
Raw On
WSD Print On
POP3
(E-mail RX)
Off
Send
Protocols
SMTP
(E-mail TX)
Off
SMTP
Security
Off
FTP
Encryption TX
Off
SMB On
WSD Scan On
DSM Scan Off
eSCL On
eSCL over SSL
On
Other
Protocols
SNMPv1/v2c On
SNMPv3 Off
HTTP On
Enhanced
WSD
On
LDAP Off
IEEE802.1X Off
LLTD On
15
Security
Settings
Device
Security
Device
Security
Settings
Authentication
Security
Settings
Password
Policy
Settings
Password
Policy
Off
Maximum
password
age
Off
Minimum
password
length
Off
Password
complexity
No more than
two consecutive
identical char
User Account
Lockout
Settings
Lockout
Policy
Off
Number of
Retries until
Locked
3 times
Lockout
Duration
1 minute
Lockout
Tar ge t
Remote Login
Only
Network
Security
Network
Security
Settings
Secure
Protocol
Settings
SSL On
Serverside
Settings
TLS Version
SSL3.0/TLS1.0:
Enable
TLS1.1: Enable
TLS1.2: Enable
HTTP
Security
Secure Only
(HTTPS)
IPP Security Secure Only
(IPPS)
Clientside
Settings
TLS Version
SSL3.0/TLS1.0:
Enable
TLS1.1: Disable
TLS1.2: Disable
Certificate
Verification
On
Item Value
16
Items changed on the machine
The initial value of the custom box
Management
Settings
Authentication
Settings Authentication
Settings
General Authentication
Off
Local
Authorization
Settings
Local
Authorization
Off
Guest
Authorization
Settings
Guest
Authorization
Off
Simple Login
Settings
Simple Login
Off
History
Settings
History Settings
Job Log History
Recipient
E-mail Address
No setting
Auto Sending
Off
Login History
Settings
Login History
Off
Recipient
E-mail Address
No setting
Auto Sending
Off
Device Log
History Settings
Device Log
History
Off
Recipient
E-mail Address
No setting
Auto Sending
Off
Secure
Communication
Error Log
History Settings
Secure
Communicatio
n Error Log
History
Off
Recipient
E-mail Address
No setting
Auto Sending
Off
Item Value
System Menu System/Network Security Level High
Internet Internet Browser Off
Item Value
Box Owner None
Box Permission Private
Item Value
2016.1
3MS2NDKDEN0
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
KYOCERA CS 358ci User guide
-
KYOCERA TASKalfa Pro 15000c User guide
-
-
KYOCERA CS 4003i User guide
-
KYOCERA ECOSYS M3860idnf User guide
-
KYOCERA CS 3051ci User guide
-
KYOCERA ECOSYS P4040dn User guide
-
KYOCERA ECOSYS M4132idn User guide
-
KYOCERA ECOSYS M6635cidn User guide
-
KYOCERA CS 508ci User guide
Other documents
-
Copystar ECOSYS M3860idnf Operating instructions
-
Copystar CS 4003i Operating instructions
-
Utax 2508ci Operating instructions
-
Copystar ECOSYS P3260dn Operating instructions
-
Copystar TASKalfa 2554ci Operating instructions
-
Ricoh MP W6700SP User guide
-
Triumph-Adler P-6038i MFP Owner's manual
-
Triumph-Adler 3561i Owner's manual
-
Triumph-Adler 4007ci Owner's manual
-
Triumph-Adler 502ci Owner's manual