Extron electronics DTP CrossPoint 86 4K User manual

DTP CrossPoint 86 4K
Brand
Extron electronics
Model
DTP CrossPoint 86 4K
Type
User manual
68-2368-51 Rev. B
10 19
DTP CrossPoint 4K Series
Scaling Presentation Matrix Switcher
Matrix Switcher
Setup Guide
Safety Instructions
Safety Instructions • English
WARNING: This symbol, , when used on the product, is
intended to alert the user of the presence of uninsulated
dangerous voltage within the product’s enclosure that may
present a risk of electric shock
.
ATTENTION: This symbol, , when used on the product, is
intended to alert the user of important operating and
maintenance (servicing) instructions in the literature provided
with the equipment.
For information on safety guidelines, regulatory compliances, EMI/EMF
compatibility, accessibility, and related topics, see the Extron Safety and
Regulatory Compliance Guide, part number 68-290-01, on the Extron
website, www.extron.com.
Sicherheitsanweisungen • Deutsch
WARNUNG: Dieses Symbol auf dem Produkt soll den
Benutzer darauf aufmerksam machen, dass im Inneren
des Gehäuses dieses Produktes gefährliche Spannungen
herrschen, die nicht isoliert sind und die einen elektrischen
Schlag verursachen können.
VORSICHT: Dieses Symbol auf dem Produkt soll dem
Benutzer in der im Lieferumfang enthaltenen Dokumentation
besonders wichtige Hinweise zur Bedienung und Wartung
(Instandhaltung) geben.
Weitere Informationen über die Sicherheitsrichtlinien,
Produkthandhabung, EMI/EMF-Kompatibilität, Zugänglichkeit und
verwandte Themen finden Sie in den Extron-Richtlinien für Sicherheit
und Handhabung (Artikelnummer 68-290-01) auf der Extron-Website,
www.extron.com.
Instrucciones de seguridad • Español
ADVERTENCIA: Este símbolo, , cuando se utiliza en el producto,
avisa al usuario de la presencia de voltaje peligroso sin aislar
dentro del producto, lo que puede representar un riesgo de
descarga eléctrica.
ATENCIÓN: Este símbolo, , cuando se utiliza en el producto,
avisa al usuario de la presencia de importantes instrucciones
de uso y mantenimiento recogidas en la documentación
proporcionada con el equipo.
Para obtener información sobre directrices de seguridad, cumplimiento
de normativas, compatibilidad electromagnética, accesibilidad y
temas relacionados, consulte la Guía de cumplimiento de normativas
y seguridad de Extron, referencia 68-290-01, en el sitio Web de Extron,
www.extron.com.
Instructions de sécurité • Français
AVERTISSEMENT: Ce pictogramme, , lorsqu’il est utilisé
sur le produit, signale à l’utilisateur la présence à l’intérieur
du boîtier du produit d’une tension électrique dangereuse
susceptible de provoquer un choc électrique.
ATTENTION: Ce pictogramme, , lorsqu’il est utilisé sur le produit,
signale à l’utilisateur des instructions d’utilisation ou de
maintenance importantes qui se trouvent dans la documentation
fournie avec le matériel.
Pour en savoir plus sur les règles de sécurité, la conformité à la
réglementation, la compatibilité EMI/EMF, l’accessibilité, et autres sujets
connexes, lisez les informations de sécurité et de conformité Extron, réf.
68-290-01, sur le site Extron, www.extron.com.
Istruzioni di sicurezza • Italiano
AVVERTENZA: Il simbolo, , se usato sul prodotto,
serve ad avvertire l'utente della presenza di tensione
non isolata pericolosa all'interno del contenitore
del prodotto che può costituire un rischio di scosse
elettriche.
ATTENTZIONE: Il simbolo, , se usato sul prodotto,
serve ad avvertire l'utente della presenza di importanti
istruzioni di funzionamento e manutenzione nella
documentazione fornita con l'apparecchio.
Per informazioni su parametri di sicurezza, conformità alle normative,
compatibilità EMI/EMF, accessibilità e argomenti simili, fare riferimento
alla Guida alla conformità normativa e di sicurezza di Extron, cod.
articolo 68-290-01, sul sito web d
i Extron, www.extron.com.
Instrukcje bezpieczeństwa • Polska
OSTRZEŻENIE: Ten symbol, , gdy używany na produkt, ma
na celu poinformować użytkownika o obecności izolowanego i
niebezpiecznego napięcia wewnątrz obudowy produktu, który
może stanowić zagrożenie porażenia prądem elektrycznym.
UWAGI: Ten symbol, , gdy używany na produkt, jest
przeznaczony do ostrzegania użytkownika ważne operacyjne
oraz instrukcje konserwacji (obsługi) w literaturze, wyposażone
w sprzęt.
Informacji na temat wytycznych w sprawie bezpieczeństwa, regulacji
wzajemnej zgodności, zgodność EMI/EMF, dostępności i Tematy
pokrewne, zobacz Extron bezpieczeństwa i regulacyjnego zgodności
przewodnik, część numer 68-290-01, na stronie internetowej Extron,
www.extron.com.
Инструкция по технике
безопасности • Русский
ПРЕДУПРЕЖДЕНИЕ: Данный символ, , если указан
на продукте, предупреждает пользователя о
наличии неизолированного опасного напряжения
внутри корпуса продукта, которое может привести к
поражению электрическим током.
ВНИМАНИЕ: Данный символ, , если указан на
продукте, предупреждает пользователя о наличии
важных инструкций по эксплуатации и обслуживанию в
руководстве, прилагаемом к данному оборудованию.
Для получения информации о правилах техники
безопасности, соблюдении нормативных требований,
электромагнитной совместимости (ЭМП/ЭДС), возможности
доступа и других вопросах см. руководство по безопасности
и соблюдению нормативных требований Extron на сайте
Extron: www.extron.com, номер по каталогу - 68-290-01.
安全说明 • 简体中文
警告： 产品上的这个标志意在警告用户该产品机壳内有暴露的危险
电 压 ，有 触 电 危 险 。
注意： 产品上的这个标志意在提示用户设备随附的用户手册中有
重要的操作和维护(维修）说明。
关于我们产品的安全指南、遵循的规范、EMI/EMF 的兼容性、无障碍
使用的特性等相关内容，敬请访问 Extron 网站 www.extron.com，参见
Extron 安全规范指南，产品编号 68-290-01。
安全記事 • 繁體中文
警告: 若產品上使用此符號，是為了提醒使用者，產品機殼內存在著
可能會導致觸電之風險的未絕緣危險電壓。
注意 若產品上使用此符號，是為了提醒使用者，設備隨附的用戶手冊
中有重要的操作和維護（維修）説明。
有關安全性指導方針、法規遵守、EMI/EMF 相容性、存取範圍和相關
主題的詳細資訊，請瀏覽 Extron 網站：www.extron.com，然後參閱
《Extron 安全性與法規遵守手冊》，準則編號 68-290-01。
安全上のご注意 • 日本語
警告:この記号 が製品上に表示されている場合は、筐体内に絶縁さ
れていない高電圧が流れ、感電の危険があることを示してい
ます。
注意: この記号 が製品上に表示されている場合は、本機の取扱
説明書に 記載されている重要な操作と保守(整備)の指示につい
てユーザーの 注意を喚起するものです。
安全上のご注意、法規厳守、EMI/EMF適合性、その他の関連項目に
つ い て は 、エ ク スト ロ ン の ウェ ブ サ イト www.extron.comよ り 『 Extron
Safety and Regulatory Compliance Guide』 (P/N 68-290-01) をご覧く
ださい。
안전 지침 • 한국어
경고: 이 기호 , 가 제품에 사용될 경우, 제품의 인클로저 내에 있는
접지되지 않은 위험한 전류로 인해 사용자가 감전될 위험이 있음을
경고합니다.
주의: 이 기호 , 가 제품에 사용될 경우, 장비와 함께 제공된
책자에 나와 있는 주요 운영 및 유지보수(정비) 지침을 경고합니다.
안전 가이드라인, 규제 준수, EMI/EMF 호환성, 접근성, 그리고 관련
항목에 대한 자세한 내용은 Extron 웹 사이트(www.extron.com)의 Extron
안전 및 규제 준수 안내서, 68-290-01 조항을 참조하십시오.
NOTE: For more information on safety guidelines, regulatory compliances,
EMI/EMF compatibility, accessibility, and related topics, see the “
Extron Safety
and Regulatory Compliance Guide
” on the Extron website.
Copyright
© 2017-2019 Extron Electronics. All rights reserved. www.extron.com
Trademarks
All trademarks mentioned in this guide are the properties of their respective owners.
The following registered trademarks, registered service marks, and trademarks are the
property of RGB Systems, Inc. or Extron Electronics (see the current list of trademarks on
the Terms of Use page at www.extron.com):
Registered Trademarks
(®)
Extron, Cable Cubby, ControlScript, CrossPoint, DTP, eBUS, EDID Manager,
EDID Minder, FlatField, FlexOS, Glitch Free, GlobalConfigurator, Global Scripter,
GlobalViewer, Hideaway, HyperLane, HyperLane, IPIntercom, IPLink, KeyMinder,
LinkLicense, LockIt, MediaLink, MediaPort, NetPA, PlenumVault, PoleVault, PowerCage,
PURE3, Quantum, Show Me, SoundField, SpeedMount, SpeedSwitch, StudionStation,
SystemINTEGRATOR, TeamWork, TouchLink, VideoLounge, V-Lock, VN-Matrix,
VoiceLift, WallVault, WindoWall, XPA, XTP, XTPSystems, and ZipClip
Registered Service Mark
(SM)
: S3 Service Support Solutions
Trademarks
(
™
)
AAP, AFL (Accu-RATEFrameLock), ADSP(Advanced Digital Sync Processing),
Auto-Image, AVEdge, CableCover, CDRS(ClassDRippleSuppression), DDSP(Digital
Display Sync Processing), DMI (DynamicMotionInterpolation), DriverConfigurator,
DSPConfigurator, DSVP(Digital Sync Validation Processing), eLink, EQIP, EverLast,
FastBite, Flex55, FOX, FOXBOX, IP Intercom HelpDesk, MAAP, MicroDigital, Opti-Torque,
PendantConnect, ProDSP, QS-FPC(QuickSwitch Front Panel Controller), Room
Agent, Scope-Trigger, ShareLink, SIS, SimpleInstructionSet, Skew-Free, SpeedNav,
Triple-Action Switching, True4K, Vector™ 4K, WebShare, XTRA, and ZipCaddy
FCC Class A Notice
This equipment has been tested and found to comply with the
limits for a Class A digital device, pursuant to part15 of the
FCC rules. The ClassA limits provide reasonable protection
against harmful interference when the equipment is operated in
a commercial environment. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used
in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment
in a residential area is likely to cause interference. This interference
must be corrected at the expense of the user.
ATTENTION:
• The Twisted Pair Extension technology works with
unshielded twisted pair (UTP) or shielded twisted
pair (STP) cables; but to ensure FCC Class A and CE
compliance, STP cables and STP Connectors are
required.
• La technologie extension paires torsadées fonctionne
avec les câbles paires torsadées blindées(UTP) ou non
blindées(STP). Afin de s’assurer de la compatibilité entre
FCC ClasseA et CE, les câbles STP et les connecteurs
STP sont nécessaires.
Battery Notice
This product contains a battery. Do not open the unit to
replace the battery. If the battery needs replacing, return
the entire unit to Extron (for the correct address, see the Extron
Warranty section on the last page of this guide).
CAUTION: Risk of explosion. Do not replace the battery with
an incorrect type. Dispose of used batteries according to the
instructions.
ATTENTION : Risque d’explosion. Ne pas remplacer la
pile par le mauvais type de pile. Débarrassez-vous des piles
usagées selon le mode d’emploi.
Conventions Used in this Guide
Notifications
ATTENTION:
•
Risk of pr
operty damage.
•
Risque de dommages matériels.
NOTE: A note draws attention to important information.
TIP: A tip provides a suggestion to make working with the
application easier.
Software Commands
Commands are written in the fonts shown here:
^AR Merge Scene,,Op1 scene 1,1 ^B 51 ^W^C
[01] R 0004 00300 00400 00800 00600 [02] 35 [17] [03]
E X! *X1&* X2)* X2#* X2! CE}
NOTE: For commands and examples of computer or device
responses mentioned in this guide, the character “0” is used
for the number zero and “O” is the capital letter “o.”
Computer responses and directory paths that do not have
variables are written in the font shown here:
Reply from 208.132.180.48: bytes=32 times=2ms TTL=32
C:\Program Files\Extron
Variables are written in slanted form as shown here:
ping xxx.xxx.xxx.xxx —t
SOH R
Data STX Command ETB ETX
Selectable items, such as menu names, menu options, buttons,
tabs, and eld names are written in the font shown here:
From the File menu, select New.
Click the OK button.
Specifications Availability
Product specications are available on the Extron website,
www.extron.com.
DTP CrossPoint 4K Series • Contents vii
Contents
Introduction ................................ 1
About this Guide ........................... 1
About the DTP CrossPoint 4K
Series ........................................... 2
DTP Input and Output
Signals ...................................... 3
Installation
.................................. 4
Rear Panel ..................................... 4
Video Inputs and Outputs ......... 4
Audio Inputs and Outputs ......... 7
Serial and IR Insertion
Connections ............................. 8
Control Connections ................. 9
Switcher Reset ........................ 10
Power ...................................... 11
Additional Connector
Information ............................. 11
Front Panel .................................. 16
Front Panel Operations
............. 17
Creating a Tie
Recalling a Preset ....................... 18
Viewing Ties ................................ 18
Assigning a Logo to an Output ... 19
Viewing and Adjusting Volume
and Mic Volume ......................... 19
Setting the Front Panel Locks
(Executive Modes) ..................... 20
Selecting Lock Mode 2 or
Toggling between Mode 2
and Mode 0 ............................ 21
Selecting Lock Mode 2 or
Toggling between Mode 2
and Mode 1 ............................ 21
Remote Control ........................ 22
Selected SIS Commands ............ 22
Establishing a Network
(Ethernet) Connection ............ 22
Number of Connections .......... 23
Establishing a USB Port
Connection ............................. 23
Host-to-Switcher
Instructions ............................. 23
Common SIS Command
Symbols ................................. 23
SIS Command and
Response Table for Matrix
Switcher Commands .............. 24
Installing and Starting the
Control Programs ....................... 28
Installing the programs ............ 28
Starting the Product
Configuration Software .......... 30
Starting the DSP
Configurator Program ............ 31
Accessing the HTML Pages ........ 33
viii DTP CrossPoint 4K Series • Contents
DTP CrossPoint 4K Series • Introduction 1
Introduction
This section gives an overview of the Extron
DTP CrossPoint 4K Series matrix switchers and describes their
features. Topics that are covered include:
• About this Guide
•
About the
DTP CrossPoint 4K Series
About this Guide
NOTE: For more information on subjects in this guide, see
the DTP CrossPoint 4K Series User Guide and the IPCP Pro
Series User Guide, at www.extron.com.
This guide provides instructions for an experienced installer to
set up and operate the Extron DTP CrossPoint 4K Series matrix
switchers. Step by step instructions show you how to:
•
Connect the har
dware (see Rear Panel on page 4)
• Perform basic operations from the front panel (see Front
Panel Operations on page 17)
•
Use selected SIS commands (see
SIS Command and
Response Table for Matrix Switcher Commands on
page24)
•
Load and start the contr
ol programs (see Starting the
Product Configuration Software on page 30 and Starting
the DSP Configurator Program on page 31)
•
Connect to the built-in HTML pages (see
Accessing the
HTML pages, on page 33)
2 DTP CrossPoint 4K Series • Introduction
About the DTP CrossPoint 4K Series
The matrix switchers distribute HDCP-compliant HDMI and
Extron proprietary DTP video and audio signal types (see gure1).
A matrix switcher routes any input signal to any combination of
outputs. It can route multiple input and output congurations
simultaneously.
POWER
12V
2
--A MAX
Rx GTx RxTxG
RS-232 IR
RxTx
1
RGB, Y, R-Y, B-Y HDMI HDMI
SIG LINK
DTP OUT
AUDIO
CONTACT
RS-232TALLY
3
123G123+V
RESET
INPUTS
OVER DTPREMOTE
DTP HDMI 330 Rx
OVER DTP
RS-232
IR
TxRx Tx RxG
LR
POWER
12V
0.7A MAX
AUDIO
SIG LINK
DTP IN
OUTPUTS
50-60 Hz
100-240V ~
--A MAX
1
L
R
1 2 3 4 5A 6A
XTP
Tx Rx
RTS CTS
GTxRxG Tx Rx G
RS-232 IR
Tx Rx Tx RxG
Tx Rx G
RESET
XTP
DTP
XTP
DTP
EXP
+48V
MIC/LINE
1
1
3
2
4
2
3
4
LINK
LAN
AV LAN 2
AV LAN 3
AV LAN 1
DTP
HDBT
1234 57 86
DTP CROSSPOINT 108 4K
4
CLASS 2 WIRING
8/
R
OVER TP
REMOTE
SIG LINK
IN
SIG LINK
IN
AUDIO INPUTS
AUDIO OUTPUTS
AMP OUTPUT
CONTROL
1234G
DIGITAL I/OCOM 3COM 2COM 1
S
DMP EXPANSION
SGG
1
1
2
2
C34C
INPUTS
INPUTS
-S G+S+V
PWR OUT = 6W
OUTPUTS
RS-232 IR
Tx Rx Tx RxG
RS-232 IR
Tx Rx Tx RxG
XTP
DTP
XTP
DTP
91
0
OVER TP
SIG LINK
IN
SIG LINK
IN
RS-232 IR
Tx Rx Tx RxG
1
LR
1
LR
3
LR
3
LR
5
LR
2
LR
4
LR
2
LR
4
LR
6
LR
IR/SERIALeBUSRELAYS
SIG LINK
OUT
SIG LINK
OUT
5B 6B 6
RS-232 IR
Tx Rx Tx Rx
XTP
S/PDIF
OUT
DTP
HDBT
G
RS-232 IR
Tx Rx Tx RxG
OVER TP
XTP
DTP
HDBT
SIG LINK
OUT
SIG LINK
OUT
78
RS-232 IR
Tx Rx Tx Rx
XTP
DTP
HDBT
G
RS-232 IR
Tx Rx Tx RxG
OVER TP
1
OUTPUTS
AUDIO
TxRx GTxRx
RS-232 IR
OVER DTP
OUTPUTS
AUDIO
TxRx GTxRx
RS-232 IR
OVER DTP
MODEL 80
FLAT PANEL
Monday, December 16, 2013 7:04 AM
Menu DeleteKey
2
ABC
3
DEF
6
MNO
5
JKL
4
GHI
9
WXYZ
8
TUV
0
7
PQRS
1
800.633.9876
End
Call
Call
Enter
Full
Screen
Camera DisplayPresets
Privacy
Near
End
Zoom
In
Zoom
Out
Far
End
Contacts
Name +-
Sources
Andrew
Video Window
Beth
Charlie
David
Ervin
Frank
Greg
Harold
Kevin
Mike
Andrew
(800) 633 - 9876
1 2 3
Extron
SM 26
Surface Mount
Speakers
Microphones
Ext
ron
DTP T
USW 333
T
ransmitter
CATx Cable
up to 330' (100 m)
RS-232
Blu-ray Player
Medi
a Player
Display
RS-232
RS-232
Relay
HDMI
HDMI
HDMI
HDMI
IR
IR
Extron
DTP HDMI
4K 230 D Rx
Receiver
CATx Cable
up to 330' (100 m)
CATx Cable
up to 230' (70 m)
Extron
DTP HDMI
4K 330 Rx
Receiver
Projector
Screen Control
Extron
DTP CrossPoint
108 4K IPCP SA
Scaling Presentation
Matrix
Ethernet
Ethernet
Ethernet/PoE
TCP/IP
Network
Extron
TLP Pro 1220TG
12" Tabletop
TouchLink Pro
Touchpanel
Wireless
Ex
tron
Contro
l
Ap
p
Power
Injector
Figure 1. Typical DTP CrossPoint Application
The switchers are available in four matrix sizes (the number
of inputs and outputs) and three equipment congurations
(differentiated by their audio and control capabilities) for a total of
12 models:
Matrix sizes —
• DTP CrossPoint 108 4K — 10x8 DTP matrix switcher
• DTP CrossPoint 86 4K — 8x6 DTP matrix switcher
• DTP CrossPoint 84 4K — 8x4 DTP matrix switcher
• DTP CrossPoint 82 4K — 8x2 DTP matrix switcher
1
3DTP CrossPoint 4K Series • Introduction
Equipment configurations —
•
DTP Cr
ossPoint 4K IPCP SA — Includes a stereo audio
amplifier and a built-in Extron IPCP Pro control processor
•
DTP Cr
ossPoint 4K IPCP MA — Includes a 70 V mono audio
amplifier and a built-in Extron IPCP Pro control processor
• DTP CrossPoint 4K — Unamplified audio outputs only,
no IPCP Pro control processor
Depending on the matrix size, two or four video outputs are
scalable.
The switchers provide four mono microphone (mic)/line level inputs
that can be mixed with or across one or all audio outputs.
The IPCP models also feature the built-in Extron IPCP Pro control
processor, which has three local area network (AV LAN) Ethernet
ports, RS-232 and IR-based control, relays, and digital I/O controls
that can control and monitor a variety of external devices, such as
projectors and lights. The non-IPCP model has one Ethernet port.
The matrix switcher can be remotely controlled via an AV LAN port
(IPCP models) or LAN port (non-IPCP models), a serial port, or a
USB port connection using either the Extron Product Conguration
Software, DSP Congurator software, or the Simple Instruction Set
(SIS).
DTP Input and Output Signals
The DTP inputs and outputs are proprietary signals that are created
within any of the Extron DTP Extenders systems and transmitted
over a single shielded twisted pair (STP) or unshielded twisted pair
(TP) cable. STP cable is strongly preferred and recommended.
The DTP CrossPoint accepts DTP inputs from transmitting devices
such as the DTP T USW 333. Depending on the connected
transmitting model, it generates the DTP signal from a variety of
video and audio inputs, including HDMI, DVI, analog VGA, and
embedded and analog audio. The DTP signal can also include
bidirectional RS-232 and IR control signals from the connected
transmitting and receiving devices or inserted locally, on the DTP
CrossPoint switcher.
Depending on the technology of the transmitting or receiving
device, DTP 330 or DTP 230, the TP inputs and outputs can travel
up to 330 feet (100 meters) or 230 feet (70 meters) without a loss
of signal integrity.
4 DTP CrossPoint 4K Series • Installation
Installation
This section describes installation of the DTP CrossPoint 4K Series
including connections and features. Topics that are covered
include:
• Rear Panel
•
Fr
ont Panel
Rear Panel
ATTENTION:
• Remove system power before making all connections.
•
Débranchez l’alimentation du système avant de fair
e
n’importe quelle connexion.
NOTES:
•
The
DTP CrossPoint 86 is similar to the DTP CrossPoint 108,
(see gure 2, 4, 6, and 8) but with fewer connectors.
• The DTP CrossPoint 82 is similar to the DTP CrossPoint 84,
(see gure 3, 5, 7, and 9) but with fewer connectors.
Video Inputs and Outputs
1 2 3 4 5A 6A
XTP
RS-232 IR
Tx Rx Tx RxG
Tx Rx G
RESET
XTP
DTP
XTP
DTP
EXP
+48V
MIC/LINE
1
1
3
2
4
2
3
4
LINK
DTP
HDBT
123457 86
DTP CROSSPOINT 108 4K
OVER TP
AUDIO OUTPUTS
AMP OUTPUT
AUDIO INPUTS
DMP EXPANSION
INPUTS
OUTPUTS
RS-232 IR
Tx Rx Tx RxG
RS-232 IR
Tx Rx Tx RxG
XTP
DTP
XTP
DTP
10
OVER TP
RS-232 IR
Tx Rx Tx RxG
1
LR
1
LR
3
L R
3
LR
5
LR
2
LR
4
L R
2
LR
4
LR
6
LR
REMOTE
LAN
SIG LINK
IN
SIG LINK
IN
INPUTS
9
SIG LINK
IN
SIG LINK
IN
SIG LINK
OUT
5B 6B 6
RS-232 IR
Tx Rx Tx Rx
XTP
S/PDIF
OUT
DTP
HDBT
G
RS-232 IR
Tx Rx Tx RxG
OVER TP
XTP
DTP
HDBT
78
RS-232 IR
Tx Rx Tx Rx
XTP
DTP
HDBT
G
RS-232 IR
Tx Rx Tx RxG
OVER TP
1
CLASS 2 WIRING
70V
SIG LINK
OUT
SIG LINK
OUT
SIG LINK
OUT
50-60 Hz
100-240V ~
--A MAX
Tx Rx
RTSCTS
GTxRxG Tx Rx G
LAN
AV LAN 2
AV LAN 3
AV LAN 1
R
CONTROL
1234G
DIGITAL I/OCOM 3COM 2COM 1
SSGG
1
1
2
2
C34C
-S G+S+V
PWR OUT = 6W
IR/SERIALeBUSRELAYS
ABC BB BCCC
D
EEEE
FF
F
F
Figure 2. Video Input and Output Connectors, 10x8 Matrix
A
HDMI inputs (see page5)
B
TP (XTP/DTP) switches (see page5)
C
TP inputs (see page5)
D
HDMI outputs (see page 6)
E
TP (XTP/HDBT/DTP) switches (see page 6)
F
TP outputs (see page 6)
2
5DTP CrossPoint 4K Series • Installation
50-60 Hz
100-240V ~ -- A MAX
12
1 23456
3A 4A
4B 4
RS-232 IR
RS-232 IR
Tx Rx Tx RxG
Tx Rx Tx Rx
XTP
RESET
S/PDIF
OUT
DTP
XTP
DTP
XTP
DTP
XTP
DTP
+48V
MIC/LINE
1
1
3
2
4
2
3
4
EXP
HDBT
HDBT
G
7
8
DTP CROSSPOINT 84 4K
RS-232 IR
Tx Rx Tx RxG
RS-232 IR
Tx Rx Tx RxG
OVER TP
OVER TP
AUDIO OUTPUTS
AUDIO INPUTS
DMP EXPANSION
INPUTS
OUTPUTS
3B
1
LR
1
R
3
LR
3
LLR
5
LR
2
LR
4
LR
2
LR
4
LR
6
LR
Tx Rx G
REMOTE
AMP OUTPUT
CLASS 2 WIRING
1
100V
SIG LINK
OUT
SIG LINK
OUT
SIG LINK
IN
SIG LINK
IN
R
CONTROL
Tx Rx
RTSCTS
G
12
12
SGSG
C
34C+V
PWR OUT = 6W
+V D-S+S
Tx Rx G Tx Rx G1234G
COM 1 COM 3COM 2 DIGITAL I/O
AV LAN 2
LAN AV LAN 1
IR/SERIAL RELAYS DIGITA L I/O
AV LAN 3
A B CC B
D
EE
FF
Figure 3. Video Input and Output Connectors, 8x4 Matrix
A
HDMI inputs 1 through 6 (see figure 2 on page 4 and
figure 3) — Plug HDMI digital video sources (or DVI
with appropriate adapters) into these HDMI ports. See
HDMI connectors on page 11 to secure the connector to the
enclosure with a LockIt HDMI Cable Lacing Bracket.
B
TP (XTP/DTP) switches (see figure 2 and figure 3) —
XTP
DTP
ATTENTION:
• Position this switch BEFORE connecting the
appropriate device to the TP connector. Failure to
comply can damage the endpoint.
• Positionnez le sélecteur AVANT de connecter
l’appareil approprié au connecteur TP. Ne pas
respecter cette procédure pourrait endommager le
point de connexion.
The following table identies the inputs with TP switches by
matrix size.
Matrix Inputs Matrix Inputs
10x8 7 through 10 All others 7 and 8
XTP position — Select if the transmitting device is an
Extron XTP matrix switcher. The input consists of HDMI with
embedded audio plus RS-232 and IR.
DTP position — Select if the transmitting device is an Extron
DTP device. The input consists of HDMI with embedded audio,
analog audio, and RS-232 and IR. The switcher can provide
remote power to the transmitter.
C
TP inputs (see figure 2 and figure 3)— Plug
SIG LINK
IN
compatible Extron DTP or XTP signals into these
RJ-45 ports using TP cables. See TP connectors on
page 12 to wire the connectors.
ATTENTION:
• Do not connect this port to a computer data or
telecommunications network.
• Ne connectez pas ces port à des données informatiques
ou à un réseau de télécommunications.
3
6 DTP CrossPoint 4K Series • Installation
D
HDMI outputs (see figure 2 on page 4 and figure 3
on page 5) — Plug HDMI video displays (or DVI with
appropriate adapters) into these ports. See HDMI
connectors to secure the connectors to the enclosure with a
LockIt HDMI Cable Lacing Bracket.
The following table identies the HDMI outputs by matrix size.
Matrix Outputs Matrix Outputs
10x8 1, 2, 3, 4, 5A, 6A 8x6 1, 2, 3A, 4A
8x4 1, 2, 3A, 4A 8x2 1A, 2A
NOTE: The signal output on the nA HDMI output (such as
5A) is duplicated on TP output nB (such as 5B).
E
TP (XTP/HDBT/DTP) switches (see figure 2 and figure 3) —
XTP
DTP
HDBT
ATTENTION:
•
Position this switch
BEFORE connecting the
appropriate device to the TP connector. Failure
to comply can damage the endpoint.
•
Positionnez le sélecteur
AVANT de connecter
l’appareil approprié au connecteur TP. Ne
pas respecter cette procédure pourrait
endommager le point de connexion.
The following table identies the outputs with TP switches by
matrix size.
Matrix Outputs Matrix Outputs
10x8 5B, 6B, 7, 8 8x6 3B, 4B, 5, 6
8x4 3B, 4B 8x2 1B, 2B
XTP position — Select if the receiving device is an Extron
XTP matrix switcher. The TP output consists of HDMI with
embedded audio plus RS-232 and IR.
HDBT position — Select if the receiving device is a
HDBaseT-enabled device. The TP output consists of HDMI with
embedded audio plus RS-232 and IR.
DTP position — Select if the receiving device is an Extron DTP
device. The TP output consists of HDMI with embedded audio,
analog audio, RS-232 and IR, and remote power.
F
TP outputs (see figure 2 and figure 3) — Plug
SIG LINK
OUT
compatible Extron DTP receivers, XTP matrix
switchers, or HDBaseT-enabled devices into these
RJ-45 ports using TP cables. See TP connectors on
page 12 to wire the connector.
NOTE: The signal output on the nB TP output (such as 5B)
is duplicated on HDMI output nA (such as 5A).
7DTP CrossPoint 4K Series • Installation
Audio Inputs and Outputs
1 2 3 4 5A 6A
XTP
XTP
DTP
XTP
DTP
EXP
+48V
MIC/LINE
1
1
3
2
4
2
3
4
LINK
DTP
HDBT
123457 86
DTP CROSSPOINT 108 4K
SA Model
AUDIO OUTPUTS
AUDIO INPUTS
DMP EXPANSION
INPUTS
INPUTS
OUTPUTS
XTP
DTP
XTP
DTP
91
0
1
LR
1
LR
3
LR
3
LR
5
LR
2
LR
4
LR
2
LR
4
LR
6
LR
SIG LINK
OUT
5B 6B 6
XTP
S/PDIF
OUT
DTP
HDBT
Tx
XTP
DTP
HDBT
78
XTP
DTP
HDBT
Tx Rx G
RESET
REMOTE
LAN
RS-232 IR
Tx Rx Tx RxG
OVER TP
RS-232 IR
Tx Rx Tx RxG
RS-232 IR
Tx Rx Tx RxG
OVER TP
RS-232 IR
Tx Rx Tx RxG
RS-232 IR
Tx Rx Tx RxG
RS-232 IR
Tx Rx Tx RxG
OVER TP
RS-232 IR
Tx Rx Tx RxG
RS-232 IR
Tx Rx Tx RxG
OVER TP
SIG LINK
IN
SIG LINK
IN
SIG LINK
IN
SIG LINK
IN
SIG LINK
OUT
SIG LINK
OUT
SIG LINK
OUT
50-60 Hz
100-240V ~
--A MAX
AMP OUTPUT
CLASS 2 WIRING
1
L
R
48/
Tx Rx
RTSCTS
GTxRxG Tx Rx G
LAN
AV LAN 2
AV LAN 3
AV LAN 1
R
CONTROL
1234G
DIGITAL I/OCOM 3COM 2COM 1
SSGG
1
1
2
2
C34C
-S G+S+V
PWR OUT = 6W
IR/SERIALeBUSRELAYS
GHIJ
K
M
N
Figure 4. Audio Input and Output Features, 10x8 Matrix
50-60 Hz
100-240V ~ -- A MAX
12
1 23456
3A 4A
4B
RS-232 IR
RS-232 IR
Tx Rx Tx RxG
Tx Rx Tx Rx
XTP
RESET
DTP
XTP
DTP
XTP
DTP
XTP
DTP
HDBT
HDBT
G
7
8
DTP CROSSPOINT 84 4K
RS-232 IR
Tx Rx Tx RxG
RS-232 IR
Tx Rx Tx RxG
OVER TP
OVER TP
INPUTS
OUTPUTS
3B
Tx Rx G
REMOTE
SIG LINK
OUT
SIG LINK
OUT
SIG LINK
IN
SIG LINK
IN
+48V
MIC/LINE
1
1
3
2
4
2
3
4
LINK
EXP
AUDIO OUTPUTS
AUDIO INPUTS
DMP EXPANSION
1
LR
1
LR
3
LR
3
LR
5
LR
2
LR
4
LR
2
LR
4
LR
6
LR
4
S/PDIF
OUT
CLASS 2 WIRING
1
70V
MA Model
AMP OUTPUT
R
CONTROL
Tx Rx
RTSCTS
G
12
12
SGSG
C
34C+V
PWR OUT = 6W
+V D-S+S
Tx Rx G Tx Rx G1234G
COM 1 COM 3COM 2 DIGITAL I/O
AV LAN 2
LAN AV LAN 1
IR/SERIAL RELAYS DIGITA L I/O
AV LAN 3
G JH
IN
M
L
Figure 5. Audio Input and Output Features, 8x4 Matrix
G
Audio inputs 1 through 6 (see figure 4 and figure 5) —
LR
Plug balanced or unbalanced stereo audio inputs into
these 3.5 mm, 5-pole captive screw connectors (see
Local and Mic/Line audio connectors on page 14 to wire the
connectors).
H
Mic/Line inputs 1 through 4 (see figure 4 and figure 5) —
Plug microphones or other mono audio sources into
these 3.5 mm, 3-pole captive screw connectors (see
Local and Mic/Line audio connectors to wire the
connectors).
I
+48 V (phantom power) LEDs (see figure 4 and figure 5) —
+48V
1
2
Light to indicate +48 V phantom power is switched on via
software.
J
Audio outputs
(see figure 4 and figure 5)
— Plug audio
LR
devices such as an audio amplifier or powered
speakers to these 3.5 mm, 5-pole captive screw
connectors (see Local and Mic/Line audio connectors to
wire the connectors).
The following table identies the audio outputs by matrix size.
Matrix Outputs Matrix Outputs
8x2 1, 2 All others 1, 2, 3, 4
4
5
8 DTP CrossPoint 4K Series • Installation
K
Amp output 1 (SA [stereo] model, see figure 4 on page 7 ) —
Plug passive, 4 ohm or 8 ohm speakers to this
1
L
R
4
CLASS 2 WIRING
8/
5 mm, 4-pole captive screw connector to receive
the amplified audio from output 1.
L
Amp output 1 (MA [mono] model, see figure 5 on page7) —
Plug passive high-impedance speakers to this 2-pole
1
captive screw connector to receive the amplified
audio from output 1.
M
S/PDIF output (see figure 4 and
figure 5
) — Plug a
S/PDIF
OUT
compatible device into this RCA connector with a 75 ohm
digital audio cable to receive a digital audio signal from the
HDMI output digital stream.
The following table identies the HDMI audio output on the
S/PDIF output by matrix size.
Matrix Output Matrix Output
10x8 6 8x2 2
8x6, 8x4 4
N
DMP Expansion port and LED (see figure 4 and
figure 5
)—
Expansion Port — Plug an STP cable between this
EXP
LINK
port and the Expansion port on an optional Extron
DMP 128 ProDSP Digital Matrix Processor.
Link LED — Lights to indicate that the port is connected to a
compatible device.
Serial and IR Insertion Connections
RS-232 IR
Tx Rx Tx RxG
DTP CROSSPOINT 108 4K
OVER TP
INPUTS
INPUTS
OUTPUTS
RS-232 IR
Tx Rx Tx RxG
RS-232 IR
Tx Rx Tx RxG
OVER TP
RS-232 IR
Tx Rx Tx RxG
RS-232 IR
Tx Rx Tx RxG
RS-232 IR
Tx Rx Tx RxG
OVER TP
HDBT
RS-232 IR
Tx Rx Tx RxG
RS-232 IR
Tx Rx Tx RxG
OVER TP
Tx Rx G
RESET
EXP
+48V
MIC/LINE
1
1
3
2
4
2
3
4
LINK
AUDIO OUTPUTS
AMP OUTPUT
AUDIO INPUTS
DMP EXPANSION
1
LR
1
LR
3
L R
3
LR
5
LR
2
LR
4
L R
2
LR
4
LR
6
LR
REMOTE
LAN
1
CLASS 2 WIRING
70V
1 2 3 4 5A 6A
XTP
DTP
HDBT
SIG LINK
OUT
5B 6B
XTP
DTP
HDBT
SIG LINK
OUT
6
S/PDIF
OUT
XTP
DTP
7
SIG LINK
OUT
8
XTP
DTP
HDBT
SIG LINK
OUT
XTP
DTP
8
XTP
DTP
9
SIG LINK
IN
SIG LINK
IN
XTP
DTP
10
SIG LINK
IN
XTP
DTP
7
SIG LINK
IN
123456
50-60 Hz
100-240V ~
--A MAX
Tx Rx
RTSCTS
GTxRxG Tx Rx G
LAN
AV LAN 2
AV LAN 3
AV LAN 1
R
CONTROL
1234G
DIGITAL I/OCOM 3COM 2COM 1
SSGG
1
1
2
2
C34C
-S G+S+V
PWR OUT = 6W
IR/SERIALeBUSRELAYS
O
P
P
O
Figure 6. Serial and IR Insertion Connections, 10x8 Matrix
6
50-60 Hz
100-240V ~ -- A MAX
12
1 23456
3A 4A
4B
XTP
RESET
DTP
XTP
DTP
XTP
DTP
XTP
DTP
HDBT
HDBT
7
8
DTP CROSSPOINT 84 4K
INPUTS
OUTPUTS
3B
Tx Rx G
REMOTE
SIG LINK
OUT
SIG LINK
OUT
SIG LINK
IN
SIG LINK
IN
4
S/PDIF
OUT
RS-232 IR
RS-232 IR
Tx Rx Tx RxG
Tx Rx Tx RxG
RS-232 IR
Tx Rx Tx RxG
OVER TP
OVER TP
RS-232 IR
+48V
MIC/LINE
1
1
3
2
4
2
3
4
AUDIO OUTPUTS
AUDIO INPUTS
1
LR
1
R
3
LR
3
LLR
5
LR
2
LR
4
LR
2
LR
4
LR
6
LR
EXP
DMP EXPANSION
AMP OUTPUT
CLASS 2 WIRING
1
100V
R
CONTROL
Tx Rx
RTSCTS
G
12
12
SGSG
C
34C+V
PWR OUT = 6W
+V D-S+S
Tx Rx G Tx Rx G1234G
COM 1 COM 3COM 2 DIGITAL I/O
AV LAN 2
LAN AV LAN 1
IR/SERIAL RELAYS DIGITA L I/O
AV LAN 3
O
P
Figure 7. Serial and IR Insertion Connections, 8x4 Matrix
O
Over TP ports (inputs 7 through 10, see figure6 on
RS-232 IR
Tx Rx Tx RxG
page 8 and figure 7) — Plug serial RS-232 signals,
modulated IR signals, or both into these 3.5 mm, 5-pole
captive screw connectors to insert bidirectional RS-232 and IR
communications. See RS-232 and IR connectors on page 15
to wire the connectors.
The following table identies the Over TP inputs by matrix size.
Matrix Inputs Matrix Inputs
10x8 7 through 10 All others 7 and 8
P
Over TP ports (outputs 5B, 6B, 7, and 8, see figure6
RS-232 IR
Tx Rx Tx RxG
and figure 7) — Plug signals, modulated IR signals, or
both into these serial RS-232 3.5 mm, 5-pole captive
screw connectors to insert bidirectional RS-232 and IR
communications. See RS-232 and IR connectors to wire the
connectors.
The following table identies the Over TP outputs by matrix
size.
Matrix Inputs Matrix Inputs
10x8 5B, 6B, 7, 8 8x6 3B, 4B, 5, 6
8x4 3B, 4B 8x2 1B, 2B
Control Connections
Tx Rx
RTSCTS
GTxRxG Tx Rx G
Tx Rx G
LAN
AV LAN 2
AV LAN 3
AV LAN 1
DTP CROSSPOINT 108 4K
R
CONTROL
1234G
DIGITAL I/OCOM 3COM 2COM 1
SSGG
1
1
2
2
C34C
-S G+S+V
PWR OUT = 6W
IR/SERIAL eBUSRELAYS
REMOTE
LAN
RESET
EXP
+48V
MIC/LINE
1
1
3
2
4
2
3
4
LINK
AUDIO OUTPUTS
AMP OUTPUT
AUDIO INPUTS
DMP EXPANSION
1
LR
1
LR
3
L R
3
LR
5
LR
2
LR
4
L R
2
LR
4
LR
6
LR
1
CLASS 2 WIRING
70V
1 2 3 4 5A 6A
XTP
DTP
HDBT
OUTPUTS
SIG LINK
OUT
5B 6B 6
XTP
S/PDIF
OUT
DTP
HDBT
Tx
XTP
DTP
HDBT
78
XTP
DTP
HDBT
RS-232 IR
Tx Rx Tx RxG
RS-232 IR
Tx Rx Tx RxG
OVER TP
RS-232 IR
Tx Rx Tx RxG
RS-232 IR
Tx Rx Tx RxG
OVER TP
SIG LINK
OUT
SIG LINK
OUT
SIG LINK
OUT
XTP
DTP
XTP
DTP
123457 86
INPUTS
INPUTS
XTP
DTP
XTP
DTP
910
RS-232 IR
Tx Rx Tx RxG
OVER TP
RS-232 IR
Tx Rx Tx RxG
RS-232 IR
Tx Rx Tx RxG
OVER TP
RS-232 IR
Tx Rx Tx RxG
SIG LINK
IN
SIG LINK
IN
SIG LINK
IN
SIG LINK
IN
50-60 Hz
100-240V ~
--A MAX
Q
R
S
Figure 8. IPCP Control Processor and Remote Port, 10x8 Matrix
7
8
9DTP CrossPoint 4K Series • Installation
50-60 Hz
100-240V ~ -- A MAX
12
1 23456
3A 4A
4B
XTP
RESET
DTP
XTP
DTP
XTP
DTP
XTP
DTP
HDBT
HDBT
7
8
DTP CROSSPOINT 84 4K
INPUTS
OUTPUTS
3B
Tx Rx G
REMOTE
SIG LINK
OUT
SIG LINK
OUT
SIG LINK
IN
SIG LINK
IN
4
S/PDIF
OUT
RS-232 IR
RS-232 IR
Tx Rx Tx RxG
Tx Rx Tx RxG
RS-232 IR
Tx Rx Tx RxG
OVER TP
OVER TP
RS-232 IR
+48V
MIC/LINE
1
1
3
2
4
2
3
4
AUDIO OUTPUTS
AUDIO INPUTS
1
LR
1
R
3
LR
3
LLR
5
LR
2
LR
4
LR
2
LR
4
LR
6
LR
EXP
DMP EXPANSION
AMP OUTPUT
CLASS 2 WIRING
1
100V
R
CONTROL
Tx Rx
RTSCTS
G
12
12
SGSG
C
34C+V
PWR OUT = 6W
+V D-S+S
Tx Rx G Tx Rx G1234G
COM 1 COM 3COM 2 DIGITAL I/O
AV LAN 2
LAN AV LAN 1
IR/SERIAL RELAYS DIGITA L I/O
AV LAN 3
O
P
Figure 7. Serial and IR Insertion Connections, 8x4 Matrix
O
Over TP ports (inputs 7 through 10, see figure6 on
RS-232 IR
Tx Rx Tx RxG
page 8 and figure 7) — Plug serial RS-232 signals,
modulated IR signals, or both into these 3.5 mm, 5-pole
captive screw connectors to insert bidirectional RS-232 and IR
communications. See RS-232 and IR connectors on page 15
to wire the connectors.
The following table identies the Over TP inputs by matrix size.
Matrix Inputs Matrix Inputs
10x8 7 through 10 All others 7 and 8
P
Over TP ports (outputs 5B, 6B, 7, and 8, see figure6
RS-232 IR
Tx Rx Tx RxG
and figure 7) — Plug signals, modulated IR signals, or
both into these serial RS-232 3.5 mm, 5-pole captive
screw connectors to insert bidirectional RS-232 and IR
communications. See RS-232 and IR connectors to wire the
connectors.
The following table identies the Over TP outputs by matrix
size.
Matrix Inputs Matrix Inputs
10x8 5B, 6B, 7, 8 8x6 3B, 4B, 5, 6
8x4 3B, 4B 8x2 1B, 2B
Control Connections
Tx Rx
RTSCTS
GTxRxG Tx Rx G
Tx Rx G
LAN
AV LAN 2
AV LAN 3
AV LAN 1
DTP CROSSPOINT 108 4K
R
CONTROL
1234G
DIGITAL I/OCOM 3COM 2COM 1
SSGG
1
1
2
2
C34C
-S G+S+V
PWR OUT = 6W
IR/SERIAL eBUSRELAYS
REMOTE
LAN
RESET
EXP
+48V
MIC/LINE
1
1
3
2
4
2
3
4
LINK
AUDIO OUTPUTS
AMP OUTPUT
AUDIO INPUTS
DMP EXPANSION
1
LR
1
LR
3
L R
3
LR
5
LR
2
LR
4
L R
2
LR
4
LR
6
LR
1
CLASS 2 WIRING
70V
1 2 3 4 5A 6A
XTP
DTP
HDBT
OUTPUTS
SIG LINK
OUT
5B 6B 6
XTP
S/PDIF
OUT
DTP
HDBT
Tx
XTP
DTP
HDBT
78
XTP
DTP
HDBT
RS-232 IR
Tx Rx Tx RxG
RS-232 IR
Tx Rx Tx RxG
OVER TP
RS-232 IR
Tx Rx Tx RxG
RS-232 IR
Tx Rx Tx RxG
OVER TP
SIG LINK
OUT
SIG LINK
OUT
SIG LINK
OUT
XTP
DTP
XTP
DTP
123457 86
INPUTS
INPUTS
XTP
DTP
XTP
DTP
91
0
RS-232 IR
Tx Rx Tx RxG
OVER TP
RS-232 IR
Tx Rx Tx RxG
RS-232 IR
Tx Rx Tx RxG
OVER TP
RS-232 IR
Tx Rx Tx RxG
SIG LINK
IN
SIG LINK
IN
SIG LINK
IN
SIG LINK
IN
50-60 Hz
100-240V ~
--A MAX
Q
R
S
Figure 8. IPCP Control Processor and Remote Port, 10x8 Matrix
7
8
10 DTP CrossPoint 4K Series • Installation
50-60 Hz
100-240V ~ -- A MAX
+48V
MIC/LINE
1
1
3
2
4
2
3
4
EXP
DTP CROSSPOINT 84 4K
AUDIO OUTPUTS
AUDIO INPUTS
DMP EXPANSION
1
LR
1
R
3
LR
3
LLR
5
LR
2
LR
4
LR
2
LR
4
LR
6
LR
AMP OUTPUT
CLASS 2 WIRING
1
100V
12
1 23456
3A 4A
4B
RS-232 IR
RS-232 IR
Tx Rx Tx RxG
Tx Rx Tx Rx
XTP
DTP
XTP
DTP
XTP
DTP
XTP
DTP
HDBT
HDBT
G
7
8
RS-232 IR
Tx Rx Tx RxG
RS-232 IR
Tx Rx Tx RxG
OVER TP
OVER TP
INPUTS
OUTPUTS
3B
SIG LINK
OUT
SIG LINK
OUT
SIG LINK
IN
SIG LINK
IN
4
S/PDIF
OUT
R
CONTROL
Tx Rx
RTSCTS
G
12
12
SGSG
C
34C+V
PWR OUT = 6W
+V D-S+S
Tx Rx G Tx Rx G1234G
COM 1 COM 3COM 2 DIGITAL I/O
AV LAN 2
AV LAN 1
AV LAN 3
LAN
IR/SERIAL RELAYS DIGITAL I/O
Tx Rx G
REMOTE
LAN
RESET
S
R
Q
Figure 9. IPCP Control Processor and Remote Port, 8x4 Matrix
NOTE: Figure 8 on page 9 and figure9 show features for all
models. Actual models can have either a LAN port (
Q
) or a
control processor (
R
), but not both.
Q
LAN (Ethernet) port (non-IPCP model) — If desired,
LAN
connect a network WAN or LAN hub, a control system,
or a computer to the Ethernet RJ-45 port (see TP
connectors on page 12 to wire the connector).
NOTE: The factory default IP address is 192.168.254.254.
R
IPCP control processor (IPCP models) — The IPCP models
include a built-in control processor that can control and
monitor a variety of external devices. The IPCP offers RS-232
and IR-based control, relays, and digital I/O controls.
NOTE: For more information on the IPCP module used in
this product, download the IPCP Pro Series User Guide,
available at www.extron.com.
S
Remote port — Plug a serial RS-232 device into the
Tx Rx G
REMOTE
matrix switcher via this 3.5 mm, 3-pole captive screw
connector for remote control of the switcher (see
RS-232 and IR connectors on page 15 to wire the
connector).
Switcher Reset
50-60 Hz
100-240V ~
--A MAX
RESET
DTP CROSSPOINT 108 4K
EXP
+48V
MIC/LINE
1
1
3
2
4
2
3
4
LINK
AUDIO OUTPUTS
AMP OUTPUT
AUDIO INPUTS
DMP EXPANSION
1
LR
1
LR
3
L R
3
LR
5
LR
2
LR
4
L R
2
LR
4
LR
6
LR
1
CLASS 2 WIRING
70V
1 2 3 4 5A 6A
XTP
DTP
HDBT
OUTPUTS
SIG LINK
OUT
5B 6B 6
XTP
S/PDIF
OUT
DTP
HDBT
Tx
XTP
DTP
HDBT
78
XTP
DTP
HDBT
RS-232 IR
Tx Rx Tx RxG
RS-232 IR
Tx Rx Tx RxG
OVER TP
RS-232 IR
Tx Rx Tx RxG
RS-232 IR
Tx Rx Tx RxG
OVER TP
SIG LINK
OUT
SIG LINK
OUT
SIG LINK
OUT
XTP
DTP
XTP
DTP
123457 86
INPUTS
INPUTS
XTP
DTP
XTP
DTP
91
0
RS-232 IR
Tx Rx Tx RxG
OVER TP
RS-232 IR
Tx Rx Tx RxG
RS-232 IR
Tx Rx Tx RxG
OVER TP
RS-232 IR
Tx Rx Tx RxG
SIG LINK
IN
SIG LINK
IN
SIG LINK
IN
SIG LINK
IN
Tx Rx G
REMOTE
LAN
Tx Rx
RTSCTS
GTxRxG Tx Rx G
LAN
AV LAN 2
AV LAN 3
AV LAN 1
R
CONTROL
1234G
DIGITAL I/OCOM 3COM 2COM 1
SSGG
1
1
2
2
C34C
-S G+S+V
PWR OUT = 6W
IR/SERIALeBUSRELAYS
T
Figure 10. Reset button and LED
50-60 Hz
100-240V ~ -- A MAX
+48V
MIC/LINE
1
1
3
2
4
2
3
4
EXP
DTP CROSSPOINT 84 4K
AUDIO OUTPUTS
AUDIO INPUTS
DMP EXPANSION
1
LR
1
R
3
LR
3
LLR
5
LR
2
LR
4
LR
2
LR
4
LR
6
LR
AMP OUTPUT
CLASS 2 WIRING
1
100V
12
1 23456
3A 4A
4B
RS-232 IR
RS-232 IR
Tx Rx Tx RxG
Tx Rx Tx Rx
XTP
DTP
XTP
DTP
XTP
DTP
XTP
DTP
HDBT
HDBT
G
7
8
RS-232 IR
Tx Rx Tx RxG
RS-232 IR
Tx Rx Tx RxG
OVER TP
OVER TP
INPUTS
OUTPUTS
3B
SIG LINK
OUT
SIG LINK
OUT
SIG LINK
IN
SIG LINK
IN
4
S/PDIF
OUT
Tx Rx G
REMOTE
RESET
R
CONTROL
Tx Rx
RTSCTS
G
12
12
SGSG
C
34C+V
PWR OUT = 6W
+V D-S+S
Tx Rx G Tx Rx G1234G
COM 1 COM 3COM 2 DIGITAL I/O
AV LAN 2
LAN AV LAN 1
IR/SERIAL RELAYS DIGITA L I/O
AV LAN 3
T
Figure 11. Reset button and LED
9
10
11
11DTP CrossPoint 4K Series • Installation
50-60 Hz
100-240V ~ -- A MAX
+48V
MIC/LINE
1
1
3
2
4
2
3
4
EXP
DTP CROSSPOINT 84 4K
AUDIO OUTPUTS
AUDIO INPUTS
DMP EXPANSION
1
LR
1
R
3
LR
3
LLR
5
LR
2
LR
4
LR
2
LR
4
LR
6
LR
AMP OUTPUT
CLASS 2 WIRING
1
100V
12
1 23456
3A 4A
4B
RS-232 IR
RS-232 IR
Tx Rx Tx RxG
Tx Rx Tx Rx
XTP
DTP
XTP
DTP
XTP
DTP
XTP
DTP
HDBT
HDBT
G
7
8
RS-232 IR
Tx Rx Tx RxG
RS-232 IR
Tx Rx Tx RxG
OVER TP
OVER TP
INPUTS
OUTPUTS
3B
SIG LINK
OUT
SIG LINK
OUT
SIG LINK
IN
SIG LINK
IN
4
S/PDIF
OUT
R
CONTROL
Tx Rx
RTSCTS
G
12
12
SGSG
C
34C+V
PWR OUT = 6W
+V D-S+S
Tx Rx G Tx Rx G1234G
COM 1 COM 3COM 2 DIGITAL I/O
AV LAN 2
AV LAN 1
AV LAN 3
LAN
IR/SERIAL RELAYS DIGITAL I/O
Tx Rx G
REMOTE
LAN
RESET
S
R
Q
Figure 9. IPCP Control Processor and Remote Port, 8x4 Matrix
NOTE: Figure 8 on page 9 and figure9 show features for all
models. Actual models can have either a LAN port (
Q
) or a
control processor (
R
), but not both.
Q
LAN (Ethernet) port (non-IPCP model) — If desired,
LAN
connect a network WAN or LAN hub, a control system,
or a computer to the Ethernet RJ-45 port (see TP
connectors on page 12 to wire the connector).
NOTE: The factory default IP address is 192.168.254.254.
R
IPCP control processor (IPCP models) — The IPCP models
include a built-in control processor that can control and
monitor a variety of external devices. The IPCP offers RS-232
and IR-based control, relays, and digital I/O controls.
NOTE: For more information on the IPCP module used in
this product, download the IPCP Pro Series User Guide,
available at www.extron.com.
S
Remote port — Plug a serial RS-232 device into the
Tx Rx G
REMOTE
matrix switcher via this 3.5 mm, 3-pole captive screw
connector for remote control of the switcher (see
RS-232 and IR connectors on page 15 to wire the
connector).
Switcher Reset
50-60 Hz
100-240V ~
--A MAX
RESET
DTP CROSSPOINT 108 4K
EXP
+48V
MIC/LINE
1
1
3
2
4
2
3
4
LINK
AUDIO OUTPUTS
AMP OUTPUT
AUDIO INPUTS
DMP EXPANSION
1
LR
1
LR
3
L R
3
LR
5
LR
2
LR
4
L R
2
LR
4
LR
6
LR
1
CLASS 2 WIRING
70V
1 2 3 4 5A 6A
XTP
DTP
HDBT
OUTPUTS
SIG LINK
OUT
5B 6B 6
XTP
S/PDIF
OUT
DTP
HDBT
Tx
XTP
DTP
HDBT
78
XTP
DTP
HDBT
RS-232 IR
Tx Rx Tx RxG
RS-232 IR
Tx Rx Tx RxG
OVER TP
RS-232 IR
Tx Rx Tx RxG
RS-232 IR
Tx Rx Tx RxG
OVER TP
SIG LINK
OUT
SIG LINK
OUT
SIG LINK
OUT
XTP
DTP
XTP
DTP
123457 86
INPUTS
INPUTS
XTP
DTP
XTP
DTP
910
RS-232 IR
Tx Rx Tx RxG
OVER TP
RS-232 IR
Tx Rx Tx RxG
RS-232 IR
Tx Rx Tx RxG
OVER TP
RS-232 IR
Tx Rx Tx RxG
SIG LINK
IN
SIG LINK
IN
SIG LINK
IN
SIG LINK
IN
Tx Rx G
REMOTE
LAN
Tx Rx
RTSCTS
GTxRxG Tx Rx G
LAN
AV LAN 2
AV LAN 3
AV LAN 1
R
CONTROL
1234G
DIGITAL I/OCOM 3COM 2COM 1
SSGG
1
1
2
2
C34C
-S G+S+V
PWR OUT = 6W
IR/SERIALeBUSRELAYS
T
Figure 10. Reset button and LED
50-60 Hz
100-240V ~ -- A MAX
+48V
MIC/LINE
1
1
3
2
4
2
3
4
EXP
DTP CROSSPOINT 84 4K
AUDIO OUTPUTS
AUDIO INPUTS
DMP EXPANSION
1
LR
1
R
3
LR
3
LLR
5
LR
2
LR
4
LR
2
LR
4
LR
6
LR
AMP OUTPUT
CLASS 2 WIRING
1
100V
12
1 23456
3A 4A
4B
RS-232 IR
RS-232 IR
Tx Rx Tx RxG
Tx Rx Tx Rx
XTP
DTP
XTP
DTP
XTP
DTP
XTP
DTP
HDBT
HDBT
G
7
8
RS-232 IR
Tx Rx Tx RxG
RS-232 IR
Tx Rx Tx RxG
OVER TP
OVER TP
INPUTS
OUTPUTS
3B
SIG LINK
OUT
SIG LINK
OUT
SIG LINK
IN
SIG LINK
IN
4
S/PDIF
OUT
Tx Rx G
REMOTE
RESET
R
CONTROL
Tx Rx
RTSCTS
G
12
12
SGSG
C
34C+V
PWR OUT = 6W
+V D-S+S
Tx Rx G Tx Rx G1234G
COM 1 COM 3COM 2 DIGITAL I/O
AV LAN 2
LAN AV LAN 1
IR/SERIAL RELAYS DIGITA L I/O
AV LAN 3
T
Figure 11. Reset button and LED
9
10
11
T
Switcher Reset button and LED (see figure 10 and figure 11
on page 10) — Initiates four levels of matrix switcher reset.
For different reset levels, press and hold the recessed
Reset
button while the switcher is running or while you power up the
switcher (see the DTP CrossPoint 4K Series User Guide, at
www.extron.com).
NOTE: The factory configured passwords for all accounts
on this device have been set to the device serial number.
In the event of a complete system reset, the passwords
convert to the default, which is no password.
Power
50-60 Hz
100-240V ~
--A MAX
DTP CROSSPOINT 108 4K
Tx Rx G
RESET
EXP
+48V
MIC/LINE
1
1
3
2
4
2
3
4
LINK
AUDIO OUTPUTS
AMP OUTPUT
AUDIO INPUTS
DMP EXPANSION
1
LR
1
LR
3
L R
3
LR
5
LR
2
LR
4
L R
2
LR
4
LR
6
LR
REMOTE
LAN
1
CLASS 2 WIRING
70V
1 2 3 4 5A 6A
XTP
DTP
HDBT
OUTPUTS
SIG LINK
OUT
5B 6B 6
XTP
S/PDIF
OUT
DTP
HDBT
Tx
XTP
DTP
HDBT
78
XTP
DTP
HDBT
RS-232 IR
Tx Rx Tx RxG
RS-232 IR
Tx Rx Tx RxG
OVER TP
RS-232 IR
Tx Rx Tx RxG
RS-232 IR
Tx Rx Tx RxG
OVER TP
SIG LINK
OUT
SIG LINK
OUT
SIG LINK
OUT
XTP
DTP
XTP
DTP
123457 86
INPUTS
INPUTS
XTP
DTP
XTP
DTP
91
0
RS-232 IR
Tx Rx Tx RxG
OVER TP
RS-232 IR
Tx Rx Tx RxG
RS-232 IR
Tx Rx Tx RxG
OVER TP
RS-232 IR
Tx Rx Tx RxG
SIG LINK
IN
SIG LINK
IN
SIG LINK
IN
SIG LINK
IN
Tx Rx
RTSCTS
GTxRxG Tx Rx G
LAN
AV LAN 2
AV LAN 3
AV LAN 1
R
CONTROL
1234G
DIGITAL I/OCOM 3COM 2COM 1
SSGG
1
1
2
2
C34C
-S G+S+V
PWR OUT = 6W
IR/SERIALeBUSRELAYS
U
Figure 12. Power connector
U
Power connector — Plug the switcher into a grounded AC
source.
Additional Connector Information
HDMI connectors
Use a LockIt Lacing Bracket to securely fasten each HDMI cable to
the switcher as follows:
1. Plug the HDMI cable into the panel connection (see figure13,
1
).
3
333
111
444
555
222
Figure 13. LockIt Lacing Bracket
2. Loosen the HDMI connection mounting screw from the panel
enough to allow the LockIt Lacing Bracket to be placed over
it (
2
). The screw does not have to be removed.
12
13
12 DTP CrossPoint 4K Series • Installation
3. Place the LockIt Lacing Bracket on the screw and against the
HDMI connector (see figure13,
3
, on page11), and then
tighten the screw to secure the bracket.
ATTENTION:
•
Do not overtighten the HDMI connector mounting scr
ew.
The shield it fastens to is very thin and can easily be
stripped.
•
Ne serr
ez pas trop la vis de montage du connecteur
HDMI. Le blindage auquel elle est attachée est très n et
peut facilement être dénudé
4.
Loosely place the included tie wrap ar
ound the HDMI
connector and the LockIt Lacing Bracket (
4
).
5.
While holding the connector secur
ely against the lacing
bracket, use pliers or a similar tool to tighten the tie wrap (
5
),
and then remove any excess length.
TP connectors
All RJ-45 ports, whether DTP ports, the Expansion port, and the
LAN (Ethernet) ports on the switcher or IPCP control processor use
twisted pair cables (see gure14).
A cable that is wired as T568A at one end
and T568B at the other (Tx and Rx pairs
reversed) is a "crossover" cable.
A cable that is wired the same at both ends is
called a "straight-through" cable, because
no pin/pair assignments are swapped.
12345678
RJ-45
Connector
Inser
t Twisted
Pair Wires
Pins:
Crossover Cable Straight-through Cable
Pin
1
2
3
4
5
6
7
8
Wire color
White-green
Green
White-orange
Blue
White-blue
Orange
White-brown
Brown
Wire color
T568A T568B
End 1 End 2 End 1 End 2
White-orange
Orange
White-green
Blue
White-blue
Green
White-brown
Brown
Pin
1
2
3
4
5
6
7
8
Wire color
White-orange
White-green
Blue
White-blue
White-brown
Brown
Wire color
T568BT568B
White-orange
OrangeOrange
White-green
Blue
White-blue
GreenGreen
White-brown
Brown
Figure 14. RJ-45 Connector and Pinout Tables
• Patch (straight) cable —
• DTP input and output ports — Shielded twisted pair
(STP) (preferred) or unshielded TP for connection to
Extron DTP transmitters and receivers, XTP matrix
switchers, or HDBaseT-enabled devices.
• Expansion port — STP for connection between the
matrix switcher and a DMP 128. A shielded 1-foot cable is
included with the DMP 128.
• AV LAN and LAN ports — Unshielded twisted pair (UTP)
or STP for connection of the LAN port to an Ethernet LAN.
14
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44

Extron electronics DTP CrossPoint 86 4K User manual

DTP CrossPoint 86 4K
Brand
Extron electronics
Model
DTP CrossPoint 86 4K
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents