KRAUS FUS-1821BN-WH Operating instructions

Type
Operating instructions

This manual is also suitable for

KRAUS FUS-1821BN-WH is a single lever basin faucet that will perfectly complement any kitchen décor. It features a stylish polished nickel finish that will add a touch of elegance to your kitchen. The faucet is made of high-quality materials, such as brass and stainless steel, which ensures durability and longevity. The faucet has a 1.2GPM flow rate, which helps to conserve water without compromising performance. It also features a ceramic disc cartridge that provides a smooth and precise water flow control. The faucet comes with all the necessary mounting hardware for easy installation.

KRAUS FUS-1821BN-WH is a single lever basin faucet that will perfectly complement any kitchen décor. It features a stylish polished nickel finish that will add a touch of elegance to your kitchen. The faucet is made of high-quality materials, such as brass and stainless steel, which ensures durability and longevity. The faucet has a 1.2GPM flow rate, which helps to conserve water without compromising performance. It also features a ceramic disc cartridge that provides a smooth and precise water flow control. The faucet comes with all the necessary mounting hardware for easy installation.

Seda™ Single Lever Basin Faucet
FUS-1821
INSTALLATION GUIDE
www.kraususa.com I Toll Free: 1.800.775.0703 I © 2017 Kraus USA Inc. I REV. October 25, 2017
2
Congratulations on the purchase of your new
Kraus plumbing xture!
Please keep the box and packaging materials until your product is
completely installed. If you have any questions, require technical
assistance, or have any problems with your product:
Please contact our Customer Service Team
1-800-775-0703 / customerservice@kraususa.com
Have the model number available, and retain a copy of your receipt
with purchase date for reference.
If for any reason this product does not meet your expectations,
please be sure to repack this product in the original box and
packaging material to avoid damage during transit.
DO NOT RETURN TO STORE
3
Prior to Installation:
Make sure you have all necessary parts by checking the diagram and parts list. If
any part is missing or damaged, please contact Kraus Customer Service at 800-
775-0703 for a replacement
Turn o the hot and cold water supply at the angle stops and turn on the old
faucet to release any built up pressure. Remove existing faucet. Clean sink or
countertop to remove any debris, plumber’s putty, or silicone
Place bucket under angle stops. Turn on angle stops to ush any debris prior to
installing new plumbing. Shut o angle stops
Pre-drilled hole size requirement: 1 3/8” (min)
Max countertop thickness: 1 3/8”
Tools you will need:
Adjustable Wrench Phillips Screwdriver
Safety Goggles Bucket
6 5/8”
5 4/5”
3/8”
(10mm)
7/8”
19.7
º
(22mm)
8 5/16”
1 1/4-18UNF-2A
(21mm)
10 1/8”
(257mm)
1 3/8”
(35mm)
3 3/4”
(168mm)
(147.3mm)
(96mm)
1 3/4”
(
45mm)
1 15/16”
(
50mm)
9/16”-18UNEF
27mm ~ 41.3mm
1 1/16” ~ 1 5/8”
1 15/16”
(
50mm)
12 7/16”
(316mm)
1 5/8”
(42.5 mm Max)
7A
8B
8C
8D
8A
7A
8B
8C
8D
8A
For technical assistance or replacement parts, please contact Kraus
Customer Service and one of our representatives will be happy to help:
Toll-Free: 800-775-0703 or Customerser[email protected]
4
D
G
B
C1
C2
C3
C4
E
F
A
A. Faucet Body
B. Base O-Ring (factory-installed)
C. Mounting Hardware:
C1. Rubber U-Washer
C2. Metal U-Washer
C3. Mounting Screw
C4. Mounting Nut
D. Hot & Cold Waterlines
E. Adjustable Aerator
F. Aerator Key
G. Hex Wrench
Diagram and Parts List
5
7.2”
183mm
5”
127mm
2.4”
61mm
5.03”
128mm
6.8”
173mm
6”
152mm
1.37”
35 mm
1.37”
35 mm
1.37” MAX
35 mm
Faucet Dimensions
6
a
b
c
d
e
f
g
i
j
k
l m
n
o
p
h
a. Waste Stopper
b. Drain
c. Rubber Washer
d. Concave Washer
e. Plastic Washer
f. Mounting Nut
g. Tailpipe Washer
h. Tailpipe
i. Top Hat Washer
j. Drain Off Pole
k. Washer
l. Retaining Nut
m. Extender Rod
n. Clip
o. Thumb Screw
p. Lift Pole
Lift Rod Drain Diagram and Parts List and Dimensions
7
Step 1: Remove mounting hardware and install waterlines
Remove faucet, mounting
hardware, and waterlines from
the box. Remove mounting nut
(C4) from mounting screw (C3).
Place faucet body (A) on a soft
cloth, spout facing up. Secure
hot & cold waterlines (D) at the
base of the faucet (hand-tighten,
then secure with ¼ turn of
adjustable wrench)
A. Hot Side: Left
B. Cold Side: Right
Thread mounting screw (C3)
into faucet base, at head up,
and tighten with a Phillips head
screwdriver until snug
Step 2: Install faucet
Install faucet body (A) through 1
3/8” hole in countertop or sink,
with base O-ring (B), hot & cold
waterlines (D), and mounting
screw (C3) attached
1 1/4-18UNF-2A
9/16”-18UNEF
27mm ~ 41.3mm
1 1/16” ~ 1 5/8”
(42.5 mm Max)
7A
8B
8C
8D
8A
7A
8B
8C
8D
8A
C4
C1
C2
C4
C4
A
C3
D
C3
C3
A
C3
D
D
E
F
1 1/4-18UNF-2A
9/16”-18UNEF
27mm ~ 41.3mm
1 1/16” ~ 1 5/8”
(42.5 mm Max)
7A
8B
8C
8D
8A
7A
8B
8C
8D
8A
C4
C1
C2
C4
C4
A
C3
D
C3
C3
A
C3
D
D
E
F
8
Step 3: Secure faucet
Install rubber U-washer (C1)
and metal U-washer (C2) from
underneath the countertop or
sink. Attach mounting nut (C4) to
mounting screw (C3) and tighten
with adjustable wrench or 10mm
wrench until snug
Step 4: Connect waterlines to main valve
Thread hot & cold waterlines (D)
onto angle stops and tighten with
adjustable wrench until snug. Turn
on angle stops and check for leaks
(DO NOT TURN FAUCET ON)
1 1/4-18UNF-2A
9/16”-18UNEF
27mm ~ 41.3mm
1 1/16” ~ 1 5/8”
(42.5 mm Max)
7A
8B
8C
8D
8A
7A
8B
8C
8D
8A
C4
C1
C2
C4
C4
A
C3
D
C3
C3
A
C3
D
D
E
F
1 1/4-18UNF-2A
9/16”-18UNEF
27mm ~ 41.3mm
1 1/16” ~ 1 5/8”
(42.5 mm Max)
7A
8B
8C
8D
8A
7A
8B
8C
8D
8A
D
Step 5: Install Drain
a
b
c
d
e
f
g
p
o
o
n
n
m
l
p
m
d
g
b
h
a
b
b
c
e
f
h
i
k
l
o
p
H1
H2
H3
j
k
l
j
Remove waste stopper (a) from
drain (b). Remove tail pipe (h),
mounting nut (f), plastic washer
(e), and concave washer (d) from
drain (b). Remove retaining nut (l)
and washer (k) from tailpipe (h)
Installer tip: Leave top hat
washer (g) in tailpipe (h)
9
Step 5: Install Drain
a
b
c
d
e
f
g
p
o
o
n
n
m
l
p
m
d
g
b
h
a
b
b
c
e
f
h
i
k
l
o
p
H1
H2
H3
j
k
l
j
a
b
c
d
e
f
g
p
o
o
n
n
m
l
p
m
d
g
b
h
a
b
b
c
e
f
h
i
k
l
o
p
H1
H2
H3
j
k
l
j
Install drain (b), with rubber
washer (c) attached, into the drain
hole. Attach concave washer (d)
with narrow end up, plastic washer
(e), and mounting nut (f) to drain
(b) from underneath countertop or
sink. Secure tightly to sink with an
adjustable wrench
Thread tailpipe (h) onto drain (b)
and hand-tighten. Adjust tailpipe
(h) so drain o pole opening is to
the rear of the sink
Installer Tip: Make sure
tailpipe washer (g) is installed
in tailpipe (h)
a
b
c
d
e
f
g
p
o
o
n
n
m
l
p
m
d
g
b
h
a
b
b
c
e
f
h
i
k
l
o
p
H1
H2
H3
j
k
l
j
Insert waste stopper (a) into
drain (b). Make sure slot at end
of waste stopper (a) is facing the
rear of the sink
10
Step 5: Install Drain
a
b
c
d
e
f
g
p
o
o
n
n
m
l
p
m
d
g
b
h
a
b
b
c
e
f
h
i
k
l
o
p
H1
H2
H3
j
k
l
j
a
b
c
d
e
f
g
p
o
o
n
n
m
l
p
m
d
g
b
h
a
b
b
c
e
f
h
i
k
l
o
p
H1
H2
H3
j
k
l
j
Insert lift pole rod (p) through the
hole in the back of the faucet body.
Loosen thumb screw (o) and attach
extender rod (m) to lift pole rod (p).
Tighten thumb screw (o)
Insert shortest end of drain o
pole (j) into drain o pole opening
of tailpipe (h). Make sure drain o
pole (j) and slot on waste stopper
(a) engage. Attach washer (k) and
retaining nut (l) through drain o
pole (j). Secure retaining nut (l) to
drain o pole opening of tailpipe (h)
Place one end of clip (n) on drain
o pole (j). Insert drain o pole (j)
through desired hole of extender
rod (m). Place other end of clip (n)
on drain o pole (j)
Installer Tip: You may adjust the
extender rod (m) to a desired
height
a
b
c
d
e
f
g
p
o
o
n
n
m
l
p
m
d
g
b
h
a
b
b
c
e
f
h
i
k
l
o
p
H1
H2
H3
j
k
l
j
11
Step6: Flush faucet
Remove adjustable aerator (E)
with aerator key (F). Turn water on
for 1 minute to remove any debris.
Reassemble aerator (E) and adjust
to desired position
1 1/4-18UNF-2A
9/16”-18UNEF
27mm ~ 41.3mm
1 1/16” ~ 1 5/8”
(42.5 mm Max)
7A
8B
8C
8D
8A
7A
8B
8C
8D
8A
C4
C1
C2
C4
C4
A
C3
D
C3
C3
A
C3
D
D
E
F
Replacement Part List - FUS-1821
2
1
17
16
3
4
5
6
7
8
9
10
11
12
13
14
15
1. Metal Handle
2. Set Screw
3. Cartridge Cover
4. Cartridge Sleeve
5. Metal O-Ring
6. Rubber Washer
7. Locking Nut
8. Cartridge
9. Base O-Ring
10. Rubber U-Washer
11. Metal U-Washer
12. Mounting Nut
13. Mounting Screw
14. Adjustable Aerator
15. Aerator Key
16. Hot & Cold Waterlines
17. Hex Wrench
12
1. Waste Stopper
2. Drain
3. Rubber Washer
4. Concave Washer
5. Plastic Washer
6. Mounting Nut
7. Tailpipe Washer
8. Tailpipe
9. Top Hat Washer
10. Drain Off Pole
11. Washer
12. Retaining Nut
13. Extender Rod
14. Clip
15. Thumb Screw
16. Lift Pole Rod
Replacement Part List - Lift Rod Drain
1
2
3
4
5
6
7
9
10
11
12 13
14
15
16
8
13
Trouble - Shooting
If you have followed the instructions carefully and your faucet still does not work
properly, take the following corrective steps:
PROBLEM CAUSE ACTION
Leakage under the handle Locking nut (7) has come
loose
Loosen set screw (2) with
hex wrench (17). Remove
metal handle (1), cartridge
cover (3), cartridge sleeve
(4), metal o-ring (5) &
rubber washer (6). Tighten
locking nut (7) with wrench
Aerator drips or has
inconsistent water flow
pattern
Aerator (14) may be dirty
or not seated properly
Unscrew aerator (14) with
aerator key (15). Remove
aerator (14) and clean out
debris
Drain is leaking Washers may be
compromised or installed
incorrectly
Check washers to make
sure they are installed
correctly and not cracked
Water will not shut off
completely
Cartridge(8) may need to
be adjusted or replaced
Loosen set screw (2)
with hex wrench (17).
Remove metal handle
(1), cartridge cover (3),
cartridge sleeve (4), metal
o-ring (5) & rubber washer
(6). Unscrew locking nut
(7) with wrench. Remove
cartridge (8). Check for
cracks
Care & Maintenance
*To keep the product clean & shining, follow the steps below:
1. Rinse with clean water & dry with a soft cloth
2. Do not clean with soaps, acid, polish, abrasives, or harsh cleaners
3. Do not use cloth with a coarse surface
4. Unscrew the aerator and clean when necessary
*This installation manual is subject to change without further notice.
1
10
279
10 31/32”
Minimum distance 90mm
Less than 90mm
Cold Water
32 3/32”
Ø35~Ø38
1
2
3
10
9
11
12
13
Hexagon Nut
Hot
Water
Cold
Water
2 3
1
4
5
7
6
8
4
5
6
7
8
Ø1 3/8”~
Ø1 1/2”
815
194
7 5/8”
Ø1 3/8~Ø1 1/2”
30˚
10
11
Close
Open
Left
Hot Water
Push
25˚
90˚
12
13
8
7
Ø35~Ø38
Max35
217
8 17/32”
Max1 3/8”
9
11
12
13
2
3
4
5
6
7
8
14
Codes/Standards Applicable:
NSF/ANSI 372
NSF/ANSI 61
ASME A112.18.1M
1.2GPM 4.5L/min maximum
GREEN
Water Eciency
LEAD FREE
I
A
P
M
O
R
&
T
TM
FAUCET WARRANTY
Kraus products are manufactured and tested to the highest quality standards by Kraus USA Inc. (“Kraus”). Kraus extends
this warranty to the original purchaser for personal household use of the “Faucet” in its original location. The warranty
is non-transferable.
Kraus warrants the structure and nish of the product to be free from defects in material and workmanship under
normal usage for the lifetime of the product. The warranty commences from the initial date of purchase by the owner
or trade professional, from an authorized Kraus dealer, through the lifetime of the original owner or end-user.
Kraus warrants the mechanical components (such as sprayhead assembly) of the product to be free from defects in
material and workmanship under normal usage for a period of one (1) year. The warranty commences from the initial
date of purchase by the owner or trade professional, from an authorized Kraus dealer, through the one (1) year term of
the original owner or end-user.
Kraus warrants the mechanical component (cartridge) of the product to be free from defects in material and
workmanship under normal usage for a period of ve (5) years. The warranty commences from the initial date of
purchase by the owner or trade professional, from an authorized Kraus dealer, through the ve (5) year term of the
original owner or end-user.
Any product reported to the authorized dealer or to Kraus as being defective within the warranty
period will be repaired
or replaced with a product of equal value at the option of Kraus. This warranty
extends to the original owner or
end-user, and is not transferable to a subsequent owner.
RESTRICTIONS
This warranty does not cover antediluvian, discontinued, or display products, whether such items are purchased at
discount outlets, unauthorized dealers, and/or sold on clearance.
This warranty does not cover instances of negligence, misuse, abuse, improper installation, carelessness, accident, hard
water or mineral deposits, exposure to corrosive materials, misapplication, damages caused by improper maintenance,
alteration of the product, or failure to follow care or installation instructions enclosed with your product. Avoid using
abrasive cleaners such as powders, bleach, ammonia, alcohol, or
chlorine. Avoid using abrasive pads, steel wool, or
wire brushes, as these will damage and wear down the nish.
This warranty does not apply to Products that have not been installed or operated in accordance with instructions
supplied by Kraus and all applicable rules, regulations, and legiswlation pertaining to such installations.
This warranty does not apply unless the Kraus product is installed by a fully insured and licensed trade professional.
Kraus insists that such professionals have experience in the installation of bathroom and kitchen manufactured goods
This warranty does not cover labor charges or costs of removal and reinstallation of said product. This warranty does
not allow recovery of incidental or consequential damages, such as loss of use, delay, property damage, or other
consequential damages, and Kraus accepts no liability for such damages.
This warranty does not cover Marine or Outdoor Installation.
Except as otherwise provided above, Kraus makes no warranties, expressed or implied, including warranties of
15
merchantability and tness for a particular purpose, or compliance with any code.
Shipping charges will be covered for the rst (1) year of the warranted replacement part or product (HI, AK, and Puerto
Rico shipping charges may apply). International shipping fees are not included.
COMMERCIAL WARRANTY
Kraus extends the above warranty for a period of one (1) year to purchasers of products for industrial, commercial, and
business use.
All incidental or consequential damages are specically excluded. No additional warranties, express or implied, are given,
including but not limited to any implied warranty of merchantability or tness for a particular purpose.
Some states do not allow the exclusion or limitation of incidental or consequential damages or limitations on how long
an implied warranty lasts, so the above limitations or exclusions may not apply to you.
This warranty gives you specic legal rights, and you may also have other rights which vary from state to state.
If you are a homeowner please contact a Kraus Customer Service Representative at:
Kraus USA, Inc.
12 Harbor Park Drive
Port Washington, NY 11050
Toll-free 800-775-0703
If you are a plumbing contractor or trade professional please contact a Kraus
Pro Representative at:
Kraus USA, Inc.
12 Harbor Park Drive
Port Washington, NY 11050
516-801-8955
If you are an Authorized Partner please contact a Partner Support Representative at:
Kraus USA, Inc.
12 Harbor Park Drive
Port Washington, NY 11050
516-801-8954
Partnersupport@kraususa.com
In requesting warranty service, please be ready to provide:
1. Proof of purchase.
2. A description of the problem.
Download the Kraus Care & Maintenance Guide at:
http://www.kraususa.com/maintenance
IMPORTANT
Register Your Kraus Product
REGISTER TODAY
http://www.kraususa.com/registration
Activate Your Warranty
Access Premium Customer Support
Get Product Information
www.kraususa.com
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16

KRAUS FUS-1821BN-WH Operating instructions

Type
Operating instructions
This manual is also suitable for

KRAUS FUS-1821BN-WH is a single lever basin faucet that will perfectly complement any kitchen décor. It features a stylish polished nickel finish that will add a touch of elegance to your kitchen. The faucet is made of high-quality materials, such as brass and stainless steel, which ensures durability and longevity. The faucet has a 1.2GPM flow rate, which helps to conserve water without compromising performance. It also features a ceramic disc cartridge that provides a smooth and precise water flow control. The faucet comes with all the necessary mounting hardware for easy installation.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI