Sensio Luce Installation guide

Brand
Sensio
Model
Luce
Type
Installation guide
Sensio House, Unit 7, Speedwell Road, Whitwood, Castleford, West Yorkshire, WF10 5PY
www.sensio.co.uk
Technical drawings for illustraon purposes only, Sensio has the right to change any informaon without
prior noce.
Waste Electrical & Electronic Equipment (WEEE)
The symbol on the product, or on the document accompanying the product, the crossed out wheelie
bin symbol, indicates that this product may not be treated as household waste.
Instead it shall be handed over to the applicable collecon point for the recycling of electrical and
electronic waste.
Safety Instrucons
5. Suitable for furniture lighng.
6. When the lamp expires the fing must be replaced
7. Class III safety extra low voltage (SELV).
1. Before commencing installaon or maintenance, isolate the main
electrical supply for the appropriate circuit at the fuse board.
2. This product is only suitable for connecng to a 240V 50Hz supply
with use of a Sensio 24V driver.
3. The lights should be mounted onto a secure surface.
4. Never exceed the total output of the LED driver.
Please read these instrucons carefully before aempng to install this
product. It is advisable to keep these instrucons in a safe place for
future reference.
We recommend that you consult a qualified electrician. All electrical
installaon must be carried out in accordance with current IEE wiring
regulaons (BS7671).
These pThese products must not be modified, if any modificaon are made, it
may invalidate the warranty and may render the product unsafe. These
LED lights operate low voltage (24V).
Do not wire the individual LED light fings directly to the mains. This
product is for indoor use only. Keep out of moisture and use only in
dry rooms.
Important Safety Informaon
• If in doubt, installaon must be carried out by a qualified
electrician.
• Install on smooth flat surface(s) only.
• Do not exceed or stretch the cable length of each LED wire.
• This product is IP20 Rated.
• The waage for each light is 0.6W. Ensure that the LED
dri driver used with these fings has an adequate max waage.
Drill
Ø44mm
Hole Saw
PencilInstallaon
Guide
Driver and 2 x Screws
(SE15090C0 & SE15090W0 Do not include a driver)
Luce Plinth Light/Lights
Components Tools required
IMPORTANT: Please read these instrucons before commencing installaon and retain for future reference.
LUCE
SLS LED SQUARE
PLINTH LIGHT
INSTALLATION
INSTRUCTIONS
Sensio V2
Maintenance & Care
• Ensure that the power is disconnected prior to cleaning.
• To keep the finish of this product, wipe over with so cloth periodically.
• Do not use harsh chemical solvents, this may dis-colour or damage the finish.
Technical drawings for illustraon purposes only, Sensio has the right to change any informaon
without prior noce.
www.sensio.co.uk
Sensio House, Unit 7, Speedwell Road, Whitwood, Castleford, West Yorkshire, WF10 5PY
Ensure that the plinth light/lights are installed in this
orientaon, so that the diodes are situated at the top of the
plinth light.
Product Informaon
Product Codes:
SE15090C0 & SE15090W0
SE15090C4 & SE15090W4 (4 Light Pack)
SE15090C8 & SE15090W8 (8 Light Pack)
Connect the driver to the mains supply, or
aach a plug.
6
If you are installing a run of lights, proceed to
connect each plinth light together by inserng
the male JB4 connector into the female
connector, in a daisy chain fashion.
54
3
Thread the cables through the hole and insert
the plinth light/lights into the hole.
Proceed to cut the hole/holes using a 44mm
diameter holesaw.
2
Carefully mark the desired locaons for your
plinth light/lights.
1
Installaon
LUCE - SLS LED SQUARE PLINTH LIGHT
Sensio V2
  • Page 1 1
  • Page 2 2

Sensio Luce Installation guide

Brand
Sensio
Model
Luce
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Other documents