PERIODICALLY CHECK THIS RECEIVER HITCH TO ENSURE ALL FASTENERS ARE TIGHT AND ALL STRUCTURAL COMPONENTS ARE SOUND
CURT Manufacturing LLC. warrants this product to be free of defects in material and/or workmanship at the time of retail purchase by the original purchaser. If the product is found to be defective, Curt Manufacturing LLC. may repair or replace
the product at their option, when the product is returned, prepaid, with proof of purchase. Alteration to, misuse of, or improper installation of this product voids the warranty. Curt Manufacturing LLC.'s liability is limited to repair or replacement
of products found to be defective, and specifically excludes liability for incidental or consequential loss or damage.
For more information log onto www curtmfg com & for helpful towing tips log onto www hitchinfo com
MAKE: STYLE:
MIN.10
WARNING: NEVER EXCEED YOUR VEHICLE MANUFACTURER'S RECOMMENDED TOWING CAPACITY
WEIGHT CARRYING:
INSTALLATION TIPS:
INSTALLATION REQUIRES:
VEHICLE PHOTO:
HITCH ILLUSTRATION:
REPRESENTATIVE PHOTO
MAKE SURE YOUR HITCH MATCHES
LEVEL OF DIFFICULTY:
EASY
EASY MODERATE CHALLENGING
1. BEFORE YOU BEGIN INSTALLATION, READ ALL
INSTRUCTIONS THOROUGHLY.
2. TO EASE INSTALLATION, 2 PEOPLE MAY BE
REQUIRED.
3. USING PROPER TOOLS WILL GREATLY IMPROVE
THE QUALITY OF THE INSTALL AND REDUCE THE
TIME REQUIRED.
4. NEED HELP OR HAVE SOME QUESTIONS?
CALL TECHNICAL SUPPORT AT 800.798.0813
Safety glasses should be
worn at all times while
installing this product
.
YEARS: 2003-PRESENT TOYOTA MODEL: COROLLA SEDAN
2,000
200
TRAILER WEIGHT:
TONGUE WEIGHT:
11265 INSTALLATION INSTRUCTIONS
LBS.
LBS.
9/11/2013
WARNING:
WE RECOMMEND THE USE OF 18050 STABILIZING STRAPS FOR ALL NON-TRAILER
(WHEEL-LESS) LOADS. PLEASE SEE THE CURT CATALOG OR VISIT US ONLINE AT
WWW.CURTMFG.COM FOR FURTHER INFORMATION.
MIN.
MIN.20
IF YOU ARE HESITANT TO UNDERTAKE
THIS TASK ON YOUR OWN, CONTACT AN AUTHORIZED
CURT INSTALLER FOR ADDITIONAL ASSISTANCE.
NOVICE INSTALL TIME:
PRO INSTALL TIME:
PART REMOVAL
SAFETY
GLASSES
TORQUE
WRENCH
RATCHET
SOCKET
EXTENSION
9"
SOCKET
19mm
- NO DRILLING REQUIRED
- CLEAN EXISTING
WELDNUTS
- REMOVE TOW LOOP(S)
(IF PRESENT)
I NSTALLATI ON WALKTHROUGH:
For more information log onto www.curtmfg.com, & for helpful towing tips log onto www.hitchinfo.com
Parts List
DESCRIPTIONPART NUMBERQTYITEM
HEX BOLTM12-1.25 x 30mm41
CONICAL TOOTHED WASHER1/242
1
2
1. If present, remove existing bolts from tow loop(s).
Return tow loop(s) and bolts to owner.
2. Raise hitch into position and align the holes in the side
plates with the weldnuts in the frame rails. Secure the
hitch using M12-1.25 x 30mm hex bolts and 1/2" conical
toothed washers.
DESIGNED FOR USE WITH
BALL MOUNT 45521
EURO MOUNT OPTION AVAILABLE
45571 (1 7/8" BALL) & 45572 (2" BALL)
INSTALLATION WALKTHROUGH:
For more information log onto www.curtmfg.com, & for helpful towing tips log onto www.hitchinfo.com
3. Torque all M12 hardware to 86 ft-lbs.
INSTALLATION COMPLETE
GROSS LOAD CAPACITY WHEN USED AS A WEIGHT CARRYING HITCH: LBS. TRAILER WEIGHT & LBS. TONGUE WEIGHT.
* * * DO NOT EX CEED V EH I CLE M AN UFA CT U RER'S RECOM M EN DED T OWI NG C APACI T Y .* * *
WARNING: ALL NON-TRAILER LOADS APPLIED TO THIS PRODUCT MUST BE SUPPORTED BY 18050 STABILIZING STRAPS.
* * FAI LURE T O PROPERLY SUPPO RT N ON-T RAI LE R LOADS WILL V OID PRODU CT WARRANTY * *
HAVING INSTALLATION QUESTIONS? CALL TECHNICAL SUPPORT AT 1-877-287-8634
HITCH WEIGHT: LBS.
INSTALL TIME
PROFESSIONAL: MINUTES
NOVICE (DIY): MINUTES
INSTALL NOTES:
INSTALLATION STEPS
PERI ODI CALLY CHECK TH I S RECEI VER H I TCH T O EN SU RE T HAT ALL FAST EN ERS
ARE TI GHT AN D TH AT ALL STRUCT U RAL COM PONEN T S ARE SOU ND.
Curt Manufacturing LLC., warrants this product to be free of defects in material and/or workmanship at the time of retail purchase by the original purchaser. If the product is found to be defective,
Curt Manufacturing LLC., may repair or replace the product, at their option, when the product is returned, prepaid, with proof of purchase. Alteration to, misuse of, or improper installation of
this product voids the warranty. Curt Manufacturing LLC.'s liability is limited to repair or replacement of products found to be defective, and specifically excludes liability for incidental or
consequential loss or damage.
2,000 200
20
10
TOYOTA COROLLA
9/11/2013
11265
20
Parts List
DESCRIPTIONPART NUMBERQTYITEM
HEX BOLTM12-1.25 x 30mm41
CONICAL TOOTHED WASHER1/242
1. If present, remove existing bolts from tow loop(s). Return tow loop(s) and bolts to owner.
2. Raise hitch into position and align the holes in the side plates with the weldnuts in the frame rails.
Secure the hitch using M12-1.25 x 30mm hex bolts and 1/2" conical toothed washers.
3. Torque all M12 hardware to 86 ft-lbs.
DRIVER SIDE
FRAME RAIL
PASSENGER SIDE
FRAME RAIL
EXISTING WELDNUTS
(BOTH SIDES)
FASCIA
DESIGNED FOR USE WITH
BALL MOUNT 45521
EURO MOUNT
OPTION AVAILABLE
45571 (1 7/8" BALL)
45572 (2" BALL)
TOW LOOP & HARDWARE
(REMOVE IF PRESENT)
- NO DRILLING
- REMOVE TOW LOOP
(IF PRESENT)
TOOLS REQUIRED
RATCHET
TORQUE WRENCH
19mm SOCKET
9" EXTENSION
SAFETY GLASSES
1
2
-
1
-
2
-
3
-
4
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Curt Manufacturing 11219 Owner's manual
-
-
-
Reese Towpower 51047 Installation guide
-
-
Draw-Tite 75126 Installation guide
-
-
-
-