Lennox G32 Installation guide

Brand: Lennox

Model: G32

Category: Water heaters & boilers

Type: Installation guide

This manual is also suitable for

G32V5-100

Page 1

05/02

*2P0502*

504,564M

*P504564M*

RETAIN THESE INSTRUCTIONS

FOR FUTURE REFERENCE

 2002 Lennox Industries Inc.

Dallas, Texas, USA

INSTALLATION

INSTRUCTIONS

G32V SERIES UNITS

GAS UNITS

504,564M

5/2002

Supersedes 504,468M

Table of Contents

G32V Unit Dimensions- inches (mm) 2. . . . . . . . . . . .

G32V Parts Arrangement 3. . . . . . . . . . . . . . . . . . . . . .

Safety Instructions 4. . . . . . . . . . . . . . . . . . . . . . . . . . . .

General 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Installation - Setting Equipment 5. . . . . . . . . . . . . . . .

Return Air Opening Guidelines 5. . . . . . . . . . . . . . . . .

Filter & Filter Assembly 6. . . . . . . . . . . . . . . . . . . . . . .

Duct System 7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Pipe & Fittings Specifications 7. . . . . . . . . . . . . . . . . .

Vent Piping Guidelines 8. . . . . . . . . . . . . . . . . . . . . . . .

Joint Cementing Procedure 9. . . . . . . . . . . . . . . . . . . .

Venting Practices 9. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Gas Piping 16. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Electrical 17. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Integrated Control Board Settings 23. . . . . . . . . . . . .

Unit Start-Up 27. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Heating Sequence of Operation 27. . . . . . . . . . . . . . .

Gas Pressure Adjustment 31. . . . . . . . . . . . . . . . . . . .

High Altitude Information 32. . . . . . . . . . . . . . . . . . . . .

Other Unit Adjustments 32. . . . . . . . . . . . . . . . . . . . . .

Service 32. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Repair Parts List 35. . . . . . . . . . . . . . . . . . . . . . . . . . . .

Integrated Control Board Diagnostic Codes 35. . . . .

Troubleshooting 36. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Start-Up & Performance Check List 42. . . . . . . . . . . .

WHAT TO DO IF YOU SMELL GAS:

Do not store or use gasoline or other flamĆ

mable vapors and liquids in the vicinity of

this or any other appliance.

Installation and service must be performed

by a qualified installer, service agency or

the gas supplier.

Do not try to light any appliance.

Do not touch any electrical switch; do not use any

phone in your building.

Immediately call your gas supplier from a neighbor's

phone. Follow the gas supplier's instructions.

If you cannot reach your gas supplier, call the

fire department.

Extinguish any open flames.

If the information in this manual is not

followed exactly, a fire or explosion

may result causing property damage,

personal injury or death.

WARNING

Leave the building immediately.

Litho U.S.A.

Page 2

G32V Unit Dimensions - inches (mm)

AIR FLOW

SUPPLY

AIR

OPENING

4 (102)

1 1/16

(41)

Return Air

Knockout (Bottom)

GAS PIPING

INLET

(Both Sides)

18 7/8

(479)

ELECTRICAL

INLETS

(Both Sides)

RETURN AIR

KNOCKOUT

(Either Side)

28 1/2

(724)

23 (584)

1-15/16 (49)

TOP VIEW

FRONT VIEWSIDE VIEW

1 1/16

(41)

(1168)

2 1/2 (64)

(51)

3 5/8

(92)

(584)

4 1/2

(114)

CONDENSATE

DRAIN

(Both Sides)

EXHAUST

AIR OUTLET

COMBUSTION

AIR INTAKE

21 3/4

(552)

7 3/8

(187)

23 3/4 (603)

25 (635)

5/8

(16)

5/8 (16)

EXTERNAL

SIDE RETURN

AIR FILTER KIT

(Either Side)

(Optional)

23 (584) D

Return Air

Knockout (Bottom)

4 (102)

Model No

A B C D E F G H

Model No. in. mm in. mm in. mm in. mm in. mm in. mm in. mm in. mm

G32V3-75 16-1/4 413 14-1/8 359 12 305 12 305 2-1/8 54 7-5/8 194 14 356 12-3/4 324

G32V5–100 21-1/4 540 19-1/8 486 18 457 18 457 1-5/8 41 10-1/8 257 20 508 18-3/4 476

G32V5–125 26-1/4 667 24-1/8 613 18 457 18 457 4-1/8 105 12-5/8 321 20 508 18-3/4 476

Page 3

G32V Parts Arrangement

FIGURE 1

TOP CAP

CABINET

GLASS FIBER GASKET

FRESH AIR

INTAKE FITTING

BURNER BOX

ASSEMBLY

PATCH

PLATE

PATCH PLATE WITH

BARBED FITTING

AND FLAME

ROLL-OUT SWITCH

TWOĆSTAGE

GAS VALVE AND

MANIFOLD

BURNER BOX

COVER

FLAME SIGHT

GLASS

DuralokPlusTM

HEAT EXCHANGER

ASSEMBLY

CONTROL VOLTAGE

CIRCUIT BREAKER

WARM

HEADER

(COLLECTOR)

BOX

COLD HEADER

(COLLECTOR)

BOX

TWO-SPEED

COMBUSTION AIR

INDUCER

COMBUSTION

AIR

ORIFICE

BLOWER

ACCESS

DOOR

BURNER

ACCESS

PANEL

FLUE

TRANSITION

LOW HEAT

DIFFERENTIAL

PRESSURE

SWITCH

SUPPLY

AIR

BLOWER

PRIMARY LIMIT

(ALTERNATE STYLES)

FLUE COLLAR

DOOR INTERLOCK SWITCH

HIGH HEAT

DIFFERENTIAL

PRESSURE

SWITCH

(-75 only)

SURELIGHT TWO-STAGE,

VARIABLE-SPEED

INTEGRATED CONTROL BOARD

SECONDARY COIL

TRANSFORMER

Page 4

Safety Instructions

Lennox G32V units are Category IV CSA International

certified to ANSI Z21.47 and CSA 2.3 standards.

In the USA, installation of Lennox gas central furnaces

must conform with local building codes. In the absence of

local codes, units must be installed according to the curĆ

rent National Fuel Gas Code (ANSI-Z223.1/NFPA 54) in

the United States. The National Fuel Gas Code is availĆ

able from the following address:

American National Standards Institute, Inc.

11 West 42nd Street

New York, NY 10036

In Canada, installation must conform with current NationĆ

al Standard of Canada CAN/CGAĆB149.1 Installation

Code for Natural Gas Burning Appliances and EquipĆ

ment" and CAN/CGA-B149.2 Installation Code for ProĆ

pane Gas Burning Appliances and Equipment," local

plumbing or waste water codes and other applicable local

codes.

This furnace is CSA International certified for installation

clearances to combustible material as listed on the unit

rating plate and in table 1.

TABLE 1

Clearances Location Inches (mm)

Front 24 (610)

Service access Condensate side 3 (76)

(from side of unit)

To p 1 (25)

To combustible Exhaust 0

combustible

materials Side, rear, and front 0

Floor 0

NOTE - For installation on combustible floors, the furnace

shall not be installed directly on carpeting, tile, or other

combustible material other than wood flooring.

Accessibility and service clearances must take preceĆ

dence over fire protection clearances.

For installation in a residential garage, the furnace must

be installed so that the burner(s) and the ignition source

are located no less than 18 inches (457 mm) above the

floor. The furnace must be located or protected to avoid

physical damage by vehicles. When a furnace is installed

in a public garage, hangar, or other building that has a

hazardous atmosphere, the furnace must be installed acĆ

cording to recommended good practice requirements

and current National Fuel Gas Code or CAN/CGA B149.1

and B149.2 standards.

When the furnace is used with cooling units, it shall be

installed in parallel with, or on the upstream side of, cool-

ing units to avoid condensation in the heating compartĆ

ment. With a parallel flow arrangement, a damper (or othĆ

er means to control the flow of air) must adequately

prevent chilled air from entering the furnace. If the dampĆ

er is manually operated, it must be equipped to prevent

operation of either the heating or the cooling unit, unless it

is in the full HEAT" or COOL" setting.

When installed, the furnace must be electrically grounded

according to local codes. In addition, in the United States,

installation must conform with the current National ElecĆ

tric Code, ANSI/NFPA No. 70. The National Electric Code

(ANSI/NFPA No. 70) is available from the following adĆ

dress:

National Fire Protection Association

1 Battery March Park

Quincy, MA 02269

In Canada, all electrical wiring and grounding for the unit

must be installed according to the current regulations of

the Canadian Electrical Code Part I (CSA Standard

C22.1) and/or local codes.

Field wiring connections must meet or exceed specificaĆ

tions of type T wire and withstand a maximum temperaĆ

ture rise of 180°F (82°C).

G32V unit must be installed so that electrical components

are protected from water.

When the furnace is installed so that supply ducts carry

air circulated by the furnace to areas outside of the space

containing the furnace, return air shall be handled by a

duct(s) sealed to the furnace casing and terminating outĆ

side space containing furnace.

WARNING

Product contains fiberglass wool.

Disturbing the insulation in this product during

installation, maintenance, or repair will expose you

to fiberglass wool dust. Breathing this may cause

lung cancer. (Fiberglass wool is known to the State

of California to cause cancer.)

Fiberglass wool may also cause respiratory, skin,

and eye irritation.

To reduce exposure to this substance or for further

information, consult material safety data sheets

available from address shown below, or contact

your supervisor.

Lennox Industries Inc.

P.O. Box 799900

Dallas, TX 75379-9900

Page 5

NOTE - G32V series units must not be used as a

construction heater during any phase of construction.

Very low return air temperatures, harmful vapors and misĆ

placement of the filters will damage the unit and lower its

efficiency.

The G32V furnace may be installed in alcoves, closĆ

ets, attics, basements, garages and utility rooms in

the upflow position.

General

The G32V is an upflow gas furnace which is factory-

equipped for use with natural gas. A changeover kit is

necessary if the furnace is to be used with L.P. gas. These

instructions are intended as a general guide and do not

supersede local codes in any way. Consult authorities

having jurisdiction before installation.

Shipping and Packing List

1 - Assembled G32V furnace

1 - 3 inch x 2 inch vent transition piece (-100, -125

units only)

1 - Bag assembly containing:

1 - Filter

1 - External filter rack for side return air application

1 - Bag assembly containing:

1 - Electrical make-up box with cover and

grounding screw

4 - Thread-forming make-up box screws

1 - Green ground wire

1 - Wiring harness

1 - Snap bushing

2 - Filter clips

1 - Condensate drain pipe adapter

1 - Condensate plug

4 - Wire nuts

2 - Lockwashers and screws

8 - Self-tapping screws

2 - Filter door pins

1 - Grounding label

1 - Wire tie

Shipping Damage

Check equipment for shipping damage. If you find any

damage, immediately contact the last carrier.

WARNING

Improper installation, adjustment, alteration, serĆ

vice or maintenance can cause property damage,

personal injury or loss of life. Installation and serĆ

vice must be performed by a qualified installer, serĆ

vice agency or the gas supplier.

CAUTION

As with any mechanical equipment, personal injuĆ

ry can result from contact with sharp sheet metal

edges. Be careful when you handle this equipment.

Installation - Setting Equipment

Select a location that allows for required clearances listed

on the unit rating plate. Also consider gas supply connecĆ

tions, electrical supply, vent connection and installation

and service clearances [24 inches (610 mm) at unit front].

The furnace must be level.

CAUTION

G32V unit should not be installed in areas normally

subject to freezing temperatures.

Return Air Opening Guidelines

WARNING

Improper installation of unit can result in personal

injury or death. Combustion and flue products

must never be allowed to enter the return air sysĆ

tem or air in the living space. Use sheet metal

screws and joint tape to seal return air system to

furnace.

In platform installations with furnace return, the

furnace should be sealed airtight to the return air

plenum. A door must never be used as a portion of

the return air duct system. The base must provide

a stable support and an airtight seal to the furnace.

Allow absolutely no sagging, cracks, gaps, etc.

For no reason should return and supply air duct

systems ever be connected to or from other heat-

ing devices such as a fireplace or stove, etc. Fire,

explosion, carbon monoxide poisoning, personal

injury and/or property damage could result.

WARNING

The blower access panel must be securely in place

when the blower and burners are operating. Gas

fumes, which could contain carbon monoxide, can

be drawn into living space resulting in personal inĆ

jury or death.

Return air can be brought in either side or at the bottom of

the unit. Scribe lines show the outline of each side and the

bottom return air opening.

Page 6

Bottom Return Air Applications

If return air is to terminate through the floor under the furĆ

nace, a direct, airtight and sealed connection must be

made to the bottom of the furnace.

1 - Cut opening in floor or platform. Using knockouts

provided, cut bottom of base panel. See figure 2.

FIGURE 2

KNOCKOUT PATTERN FOR BOTTOM

RETURN AIR APPLICATION

FIGURE 3

G32V UNIT

RETURN AIR

PLENUM

PROPERLY

SIZED FLOOR

OPENING

BOTTOM RETURN AIR APPLICATION

2 - Bend a flange on return air plenum and lower into

floor or platform opening. See figure 3.

3 - Position unit over return air opening. Seal unit air

tight with return air plenum.

NOTE - Be careful not to damage insulation. Check for

tight seal.

Side Return Air Applications

For installations where the return air is taken from a return

air drop, unit may be installed using either the left or right

side of furnace.

For side return air applications, cut the furnace cabinet at

the dimensions given in the unit dimensions graphic. EmĆ

bossed corners are pro-vided on both cabinet sides for reĆ

turn air opening location.

Filter & Filter Assembly

A filter and an external filter rack for use in side return air

applications are shipped with the unit. A filter must be in

place anytime the unit is in operation.

TABLE 2

FILTER SIZE REQUIREMENTS

UNIT MODEL

NUMBER

FILTER PART

NUMBER FILTER SIZE

G32V-75 31J81 14 inches x 25 inches

(356 x 635 mm)

G32V-100

G32V-125 P-8-7831 20 inches x 25 inches

(508 x 635 mm)

Bottom Return Air Applications

1 - Remove blower access panel.

2 - Install filter clips, provided with unit, by slipping

folded section of clip on edge of bottom opening. See

figure 4.

FIGURE 4

BOTTOM RETURN FILTER INSTALLATION

FURNACE

BASE BOTTOM

REAR FILTER CLIP

RETURN AIR OPENING

SIDE FILTER CLIPS (2)

FURNACE

FRONT

FURNACE

BACK

3 - Place filter in bottom of blower compartment beneath

rear filter clip. Press down on filter sides. Filter clips

flex allowing filter to snap into place.

4 - To remove filter, press clip and pull filter up and out.

Side Return Air Applications

1 - Align filter rack opening with the inside edge of the

side return opening. Bottom of rack should be

approximately 1 inch (25 mm) from the bottom and 3

inches (76 mm) from the front of the unit.

2 - Screw filter rack into place with the eight self drill, self

tap screws provided. See figure 5.

3 - Push filter door pins through the two holes in filter

door from the inside of the uĆchannel. See figure 6.

FIGURE 5

SIDE RETURN FILTER INSTALLATION

RETURN

AIR

OPENING

12 in. (305) for

14 in. (356) Filter

18 in. (457) for

20 in. (508) Filter

1-15/16 in.

(49)

BLOWER DECK

15/16 in

(24)

CABINET BASE BOTTOM

RETURN AIR

PLENUM SIZE

12-3/4 in X 23-1/2 in (324 X

597) for 14 in (356) Filter

18-3/4 in. x 23-1/2 in.

(476 x 597)

for 20 in. (508) Filter

in. (mm)

Page 7

4 - Position filter door on end of filter so that the thumb

tab side of the filter door is away from the furnace.

Squeeze thumb tabs to secure filter to door.

5 - Guide filter and filter door into the filter rack installed

on side of furnace. Push door into filter rack until se-

cure.

6 - To remove filter, pull filter door pins until door is re-

leased from filter rack.

FIGURE 6

FILTER DOOR ASSEMBLY

FILTER DOOR

FILTER

FILTER DOOR

TAB

Duct System

Use industry-approved standards to size and install the

supply and return air duct system. This will result in a quiet

and low-static system that has uniform air distribution. If

the G32V unit is being installed as a replacement for an

existing furnace, the existing supply and return air duct

system should be evaluated to make sure that it is approĆ

priately sized.

The total external static pressure (ESP) should not exĆ

ceed 0.8" w.c. The ESP calculation should include presĆ

sure losses caused by electronic air cleaners, filters,

cooling coils, the duct system, registers and grilles. A

properly sized duct system will help to optimize efficiency

and reliability and to minimize sound levels. Operation of

a G32V unit outside of its specified static pressure range

will result in poor performance and will reduce the useful

life-expectancy of the product and its components.

Supply Air Plenum

Furnaces installed without a cooling coil require the installaĆ

tion of a removable access panel in the supply air duct. The

access panel should be large enough to permit inspection

(either by smoke or reflected light) of the heat exchanger for

leaks after installation. The furnace access panel must alĆ

ways be in place when the furnace is operating and it must

not allow leaks into the supply air duct system.

Return Air Plenum

See dimension illustration for proper return air duct size.

NO T E - Fo r bott om re t ur n ai r, retu r n ai r duc t should be seĆ

cured to the unit using rivets or S-locks. For side return

air, secure return air duct to filter rack using screws. When

using screws, take care to avoid interference with the filĆ

ter which may cause improper filtration.

The return air must not be drawn from a room where

another gas appliance (ie., a water heater) is

installed. Even though this furnace draws its combusĆ

tion air from outside of the structure, other gas apĆ

pliances that share a utility room may not. When return

air is drawn from a room, a negative pressure is created

in the room. If a gas appliance is operating in a room

with negative pressure, the flue products can be pulled

back down the vent pipe and into the room. This reverse

flow of the flue gas may result in incomplete combustion

and the formation of carbon monoxide gas. This toxic

gas might then be distributed through the house by the

furnace duct system.

Pipe & Fittings Specifications

All pipe, fittings, primer and solvent cement must conform

with American National Standard Institute and the AmeriĆ

can Society for Testing and Materials (ANSI/ASTM) stanĆ

dards. The solvent shall be free flowing and contain no

lumps, undissolved particles or any foreign matter that

adversely affects the joint strength or chemical resistance

of the cement. The cement shall show no gelation, stratifiĆ

cation, or separation that cannot be removed by stirring.

Refer to table 3 for approved piping and fitting materials.

Primers and solvents must meet ASTM specifications.

PVC primer is specified in ASTM F 656. Use PVC solvent

cement as specified in ASTM D 2564 and ABS solvent

cement as specified in ASTM D 2235. Low temperature

solvent cement is recommended. Metal or plastic strapĆ

ping may be used for vent pipe hangers.

Table 4 lists the available exhaust termination kits. All

Lennox vent terminations are PVC.

TABLE 3

PIPING AND FITTINGS SPECIFICATIONS

PIPE & FITTING MATERIAL ASTM

SPECIFICATION

Schedule 40 PVC (Pipe) D1785

Schedule 40 PVC (Cellular Core Pipe) F891

Schedule 40 PVC (Fittings) D2466

Schedule 40 CPVC (Pipe) F441

Schedule 40 CPVC (Fittings) F438

SDR-21 PVC (Pipe) or SDR-26 PVC (Pipe) D2241

SDR-21 CPVC (Pipe) or SDR-26 CPVC (Pipe) F442

Schedule 40 ABS (Pipe) D1527

Schedule 40 ABS (Fittings) D2468

ABS-DWV (Drain Waste & Vent)

(Pipe & Fittings) D2661

PVC-DWV (Drain Waste & Vent -

Pipe & Fittings) D2665

Page 8

TABLE 4

TERMINATION KITS

Lennox Part

No. Kit LB# Description-Inches (mm)

60G77 LB-49107CE 1-1/2" (50.8) Concentric

Termination Kit

33K97 LB-87942 3" (50.8) Low Pressure Drop ConĆ

centric Term. Kit

15F75 LB-49107CC 2" (50.8) Roof

Termination Kit

22G44 LB-49107CD 2" (50.8) Wall

Assembly Termination Kit

15F74 LB-49107CB 2" (50.8) Wall Ring Kit

44J41 LB-65678A 3" (76.2) Roof

Termination Kit

44J40 LB-65701A 3" (76.2) Wall

Assembly Termination Kit

30G28 WTK 2" (50.8) Wall

Termination Extended Vent

30G79 WTKX 2" (50.8) Wall

Termination Extension Riser

CAUTION

Solvent cements for plastic pipe are flammable liqĆ

uids and should be kept away from all sources of

ignition. Do not use excessive amounts of solvent

cement when making joints. Good ventilation

should be maintained to reduce fire hazard and to

minimize breathing of solvent vapors. Avoid conĆ

tact of cement with skin and eyes.

When making ABS joints, pieces can be prepared with a

cleaner. When joining ABS to PVC materials, use PVC

solvent cement. Refer to this procedure as specified in

ASTM D3138.

Vent Piping Guidelines

Pipe used for exhaust and intake lines should be sized acĆ

cording to table 5. Note that maximum length of vent pipe

is for one run; either intake or exhaust. Maximum vent

length given is not the total length of intake plus exhaust

vents.

Each 90° elbow is equivalent to 5 feet (1.52 m) of vent

pipe. Two 45° elbows are equivalent to one 90° elbow.

One 45° elbow is equal to 2.5 feet (.76 m) of vent pipe. If

intake and exhaust piping runs are not equal in length and

number of elbows, the larger diameter pipe must be used

for both runs.

TABLE 5

VENT PIPE SIZING TABLE FOR G32V FURNACES

MINIMUM DIAMETER OF INTAKE/EXHAUST PIPE

Vent Pipe

Equivalent Length

Max. Feet (Meters)

G32V-75

75,000

BTU

G32V-100

100,000

BTU

G32V-125

125,000

BTU

15 (4.57) 2" 2" 2"

20 (6.10) 2" 2" 3"

25 (7.62) 2" 2" 3"

30 (9.14) 2" 3" 3"

40 (12.19) 2" 3" 3"

50 (15.24) 2" 3" 3"

55 (16.76) 2" 3" 3"

60 (18.29) 3" 3" 3"

70 (21.34) 3" 3" 3"

80 (24.38) 3" 3" 3"

90 (27.43) 3" 3" 3"

100 (30.48) 3" 3" 3"

110 (33.53) 3" 3" 3"

120 (36.58) 3" 3" 3"

130 (39.62) 3" 3" --

NOTE - Minimum vent pipe for G32V-75, G32V-100, and G32V-125 is 5

feet with 2 elbows of 2-inch diameter pipe.

NOTE - When you install a WTKX termination kit as part

of the intake and exhaust piping, the two 2-inch diameter

90° elbows and the 27 inch pipe (in the kit) should be inĆ

cluded in the maximum vent pipe length for each run.

For 75 kBtuh units, connections are provided for 2-inch

diameter vent pipe which should satisfy most venting reĆ

quirements. No transition pieces are provided or needed

for use with 2-inch vent pipe.

For -100 and -125 kBtuh units, the intake connection is

sized for 3-inch diameter pipe. The exhaust connection

ha s a 2- i n c h nipp l e . A pipe transition piece is shipped with

the unit for use with 3-inch pipe. See figure 7 for 2-inch

and 3-inch vent pipe applications.

Most venting applications will require 3-inch vent pipe for

proper unit operation. The intake and exhaust pipe

must never be constructed of different diameter

pipes. Regardless of the diameter of pipe used, the stanĆ

dard roof and wall terminations described in section InĆ

take and Exhaust Piping Terminations should be used.

Exhaust piping must terminate with 1-1/2 inch pipe for

1-1/2 inch or 2 inch vents and 2-inch vent pipe for 3-inch

vents.

Page 9

FIGURE 7

G32V-100 OR -125 WITH 2 IN. VENTING

G32V-100 OR -125 WITH 3 IN. VENTING

3 IN.

2 IN.

OUT

3 IN. FIELD

PROVIDED

NIPPLE

3 IN. X 2 IN.

REDUCER

2 IN. VENT PIPE

3 IN.

2 IN.

OUT

3 IN. VENT PIPE

3 IN. X 2 IN. REDUCER

2 IN. FIELD

PROVIDED

NIPPLE

Joint Cementing Procedure

All cementing of joints should be done according to the

specifications outlined in ASTM D 2855.

WARNING

DANGER OF EXPLOSION! Fumes from PVC glue

may ignite during system check. Disconnect wire

from pressure switch terminal before 115 volt powĆ

er is applied to unit. Reconnect wire after two minĆ

utes of combustion air blower operation.

1 - Measure and cut vent pipe to desired length.

2 - Debur and chamfer end of pipe, removing any ridges

or rough edges. If end is not chamfered, edge of pipe

may remove cement from fitting socket and result in

a leaking joint.

3 - Clean and dry surfaces to be joined.

4 - Test fit joint and mark depth of fitting on outside of

pipe.

5 - Uniformly apply liberal coat of PVC primer for PVC or

ABS cleaner for ABS to inside socket surface of fitĆ

ting and male end of pipe to depth of fitting socket.

6 - Promptly apply solvent cement to end of pipe and inĆ

side socket surface of fitting. Cement should be apĆ

plied lightly but uniformly to inside of socket. Take

care to keep excess cement out of socket. Apply

second coat to end of pipe.

NOTE - Time is critical at this stage. Do not allow

primer to dry before applying cement.

7 - Immediately after applying last coat of cement to

pipe, and while both inside socket surface and end of

pipe are wet with cement, forcefully insert end of pipe

into socket until it bottoms out. Turn pipe 1/4 turn durĆ

ing assembly (but not after pipe is fully inserted) to

distribute cement evenly.

NOTE - Assembly should be completed within 20 seĆ

conds after last application of cement. Hammer

blows should not be used when inserting pipe.

8 - After assembly, wipe excess cement from pipe at

end of fitting socket. A properly made joint will show a

bead around its entire perimeter. Any gaps may indiĆ

cate a defective assembly due to insufficient sol-

vent.

9 - Handle joints carefully until completely set.

Venting Practices

WARNING

Insufficient combustion air can cause headaches,

nausea, dizziness or asphyxiation. It will also

cause excess water in the heat exchanger resulting

in rusting and premature heat exchanger failure.

Excessive exposure to contaminated combustion

air will result in safety and performance related

problems. Avoid exposure to the following subĆ

stances in the combustion air supply:

Permanent wave solutions

Chlorinated waxes and cleaners

Chlorine base swimming pool chemicals

Water softening chemicals

De-icing salts or chemicals

Carbon tetrachloride

Halogen type refrigerants

Cleaning solvents (such as perchloroethylene)

Printing inks, paint removers, varnishes, etc.

Hydrochloric acid

Cements and glues

Antistatic fabric softeners for clothes dryers

Masonry acid washing materials

The thickness of construction through which vent/air inĆ

take pipes may be installed is a minimum of 3 inches (76

mm) and a maximum of 24 inches (610 mm). If a G32V

furnace replaces a furnace which was commonly vented

with another gas appliance, the size of the existing vent

pipe for that gas appliance must be checked. Without the

heat of the original furnace flue products, the existing vent

pipe is probably oversized for the single water heater or

other appliance. The vent should be checked for proper

draw with the remaining appliance.

Intake Piping

1 - Cement intake piping in slip connector located at top

of unit.

2 - Route piping to outside of structure. Continue with

installation following instructions given in exhaust

and intake piping termination section.

Page 10

Exhaust Piping

1 - Cement exhaust piping into flue collar socket located

on the left side of the top cap.

2 - All horizontal runs of exhaust pipe must slope back

toward the unit. A minimum of 1/4 inch (6 mm) drop

for each 12 inches (305 mm) of horizontal run is manĆ

datory for drainage. Horizontal runs of exhaust pipĆ

ing must be supported every 5 feet (1.52 m) using

hangers.

NOTE - Exhaust piping should be checked carefully

to make sure there are no sags or low spots.

NOTE - Exhaust piping must be insulated with 1/2

inch (13 mm) Armaflex or equivalent when run

through unheated space. Do not leave any area of

exhaust pipe open to outside air; exterior exhaust

must be insulated with 1/2 inch (13 mm) Armaflex or

equivalent.

CAUTION

Do not discharge exhaust into an existing stack or

stack that also serves another gas appliance. If verĆ

tical discharge through an existing unused stack is

required, insert PVC pipe inside the stack until the

end is even with the top or outlet end of the metal

stack.

CAUTION

The exhaust vent pipe operates under positive

pressure and must be completely sealed to pre-

vent leakage of combustion products into the livĆ

ing space.

Removal of Unit from Common Venting System

In the event that an existing furnace is removed from a

venting system commonly run with separate gas apĆ

pliances, the venting system may be too large to properly

vent the remaining attached appliances. The following

test should be conducted while all appliances (both in opĆ

eration and those not in operation) are connected to the

common venting system. If the venting system has been

installed improperly, corrections must be made as outĆ

lined in the previous section.

1 - Seal any unused openings in the common venting

system.

2 - Visually inspect the venting system for proper size

and horizontal pitch and determine there is no blockĆ

age or restriction, leakage, corrosion or other defiĆ

ciencies which could cause an unsafe condition.

3 - Close all building doors and windows, and all doors

between the space in which the appliances remainĆ

ing connected to the common venting system are loĆ

cated and other spaces of the building. Turn on

clothes dryers and any appliances not connected to

the common venting system. Turn on any exhaust

fans, such as range hoods and bathroom exhausts,

so they will operate at maximum speed. Do not operĆ

ate a summer exhaust fan. Close fireplace dampers.

4 - Follow the lighting instructions. Place the appliance

being inspected in operation. Adjust thermostat so

appliance will operate continuously.

5 - Test for spillage at the draft hood relief opening after

5 minutes of main burner operation. Use the flame of

match or candle, or smoke from a cigarette or cigar,

or a draft gauge.

6 - After determining that each appliance remaining

connected to the common venting system properly

vents when tested as indicated in step 3, return

doors, windows, exhaust fans, fireplace dampers

and any other gasĆburning appliance to their preĆ

vious condition of use.

7 - If improper venting is observed during any of the

above tests, the common venting system must be

corrected. The common venting system should be

resized to approach the minimum size as deterĆ

mined by using the appropriate tables in appendix G

in the current standards of the National Fuel Gas

Code ANSI Z223-1 in the USA, and the appropriate

Category 1 Natural Gas appliances venting sizing

tables in the current standard of the CAN/

CGA-B149.1 in the Natural Gas Installation Code in

Canada.

Intake and Exhaust Piping Terminations

Intake and exhaust pipes may be routed either horizontalĆ

ly through an outside wall or vertically through the roof. In

attic or closet installations, vertical termination through

the roof is preferred. Figures 8 through 20 show typical

terminations.

1 - Use recommended piping materials for both intake

and exhaust piping.

2 - Secure all joints, including drain leg, gas-tight using

approved cement.

3 - Piping diameters should be determined according

to length of pipe run. See table 5. Locate intake pipĆ

ing upwind (prevailing wind) from exhaust piping.

To avoid recirculation of exhaust gas on roof terĆ

minations, end of exhaust pipe must be higher than

intake pipe.

Exhaust and intake exits must be in same pressure

zone. Do not exit one through the roof and one on the

side. Also, do not exit the intake on one side and the

exhaust on another side of the house or structure.

Page 11

4 - Intake and exhaust pipes should be placed as close

together as possible at termination end (refer to ilĆ

lustrations). Maximum separation is 3 inches (76

mm) on roof terminations and 6 inches (152 mm) on

side wall terminations.

5 - Exhaust piping must terminate straight out or up as

shown. In rooftop applications, a 2 inch X 1-1/2 inch

reducer for 2 inch venting, 3 inch x 2 inch reducer for

3 inch venting must be used on the exhaust piping at

the point where it exits the structure to improve the

velocity of exhaust away from the intake piping.

On roof terminations, the intake piping should termiĆ

nate straight down using two 90° elbows. See figure 8.

FIGURE 8

ROOF TERMINATION KIT

(15F75) LB-49107CC for 2 (51) Venting

(44J41) LB-65678A for 3 (76) Venting

UNCONDITIONED

ATTIC SPACE

1/2 (13) FOAM

INSULATION IN

UNCONDITIONED

SPACE

3 x 2 (76 x 51) OR

2 x 1-1/2 (51 x 38)

PVC REDUCER

3 (76) MAX.

12 (305) ABOVE

AVERAGE SNOW

ACCUMULATION

3 (76) OR

2 (51) PVC

PROVIDE SUPPORT

FOR INTAKE AND

EXHAUST LINES

8 (203) MIN

Inches (mm)

IMPORTANT

Do not use screens or perforated metal in intake

and exhaust terminations. Doing so will cause

freeze-ups and may block the terminations.

NOTE - If winter design temperature is below 32°F (0°C),

exhaust piping must be insulated with 1/2 inch (13 mm),

Armaflex or equivalent when run through unheated

space. Do not leave any surface area of exhaust pipe

open to outside air; exterior exhaust pipe must be insuĆ

lated with 1/2 inch (13 mm) Armaflex or equivalent. In exĆ

treme cold climate areas, 3/4 inch (19 mm) Armaflex or

equivalent is recommended. Insulation on outside runs of

exhaust pipe must be painted or wrapped to protect inĆ

sulation from deterioration.

NOTE - During extremely cold temperatures, below

approximately 20°F (6.67°C), units with long runs of

vent pipe through unconditioned space, even when inĆ

sulated, may form ice in the exhaust termination that

prevents the unit from operating properly. Longer run

times of at least 5 minutes will alleviate most icing probĆ

lems. Also, a heating cable may be installed on exhaust

piping and termination to prevent freezeĆups. Heating

cable installation kit is available from Lennox. See ConĆ

densate Piping section for part numbers.

NOTE - Avoid recirculation of exhaust back into the inĆ

take pipe.

6 - On field-supplied terminations for side wall exits, exĆ

haust piping should extend a maximum of 12 inches

(305 mm) beyond the outside wall. Intake piping

should be as short as possible. See figure 9.

FIGURE 9

1/2 (13) ARMAFLEX

INSULATION IN

UNCONDITIONED SPACE

2 (51) PVC 1-1/2 (38) PVC

12 (305) MIN.

2 X 1-1/2

(51 x 38)

PVC REDUCER

1/2 (13) ARMAFLEX

INSULATION

6 (152)

MAXIMUM

2 (51) PVC

COUPLING

8 (203)

MINIMUM

OUTSIDE

WALL

Inches (mm) TOP VIEW

WALL RING KIT

(15J74) LB-49107CB for 2 (50.8) Venting

7 - On field-supplied terminations, a minimum separaĆ

tion distance between the end of the exhaust pipe

and the end of the intake pipe is 8 inches (203 mm).

8 - If intake and exhaust piping must be run up a side

wall to position above snow accumulation or other

obstructions, the piping must be supported every 3

feet (.91 m) as shown in figure 14. Refer to figures 13

and 15 for proper piping method. WTK wall terminaĆ

tion kit must be extended for use in this application.

See figure 18 or use kit WTKX shown in figure 19.

When exhaust and intake piping must be run up an

outside wall, the exhaust piping is reduced to 1 1/2

inches (38 mm) after the final elbow. The intake pipĆ

ing may be equipped with a 90° elbow turndown. UsĆ

ing tu r n-down wi ll ad d 5 fe e t (1. 5 m) to the eq u i v a l e n t

length of the pipe.

Page 12

FIGURE 10

TOP VIEW

WALL TERMINATION

(22G44) LB-49107CD for 2 (50.8) Venting

(44J40) LB-65701A for 3 (76.2) Venting

Inches (mm)

OUTSIDE WALL

1/2 (12.7) FOAM INSULATION

IN UNCONDITIONED SPACE

Optional Turndown

Shown

(Intake Only)

FIGURE 11

12 (305) ABOVE

AVERAGE SNOW

ACCUMULATION

EXHAUST

TERMINATION

INTAKE

TERMINATION

INTAKE

Inches (mm)

CONCENTRIC ROOFTOP TERMINATION

(60G77) LB-49107CE for G32V-75 Units Only

(33K97) LB-87942 for G32V-100 & -125 Units Only

FIGURE 12

EXHAUST

TERMINATION

INTAKE

TERMINATION

INTAKE 12 (305) Min.

above grade.

CONCENTRIC WALL TERMINATION

(60G77) LB-49107CE for G32V-75 Units Only

(33K97) LB-87942 for G32V-100 & -125 Units Only

Inches (mm)

OUTSIDE WALL

FIGURE 13

See venting table 5 for maximum venting lengths with

this arrangement.

12 (305) ABOVE

AVERAGE SNOW

ACCUMULATION

UNCONDITIONED

SPACE

12 (305) MIN. for 2 (51)

20 (508) MAX. for 3 (76)

8 (203)

MIN.

1/2 (13) FOAM

INSULATION

1/2 (13) FOAM

INSULATION IN

UNCONDITIONED

SPACE

PROVIDE SUPPORT

FOR INTAKE AND

EXHAUST LINES EVERY

36 (914)

OUTSIDE WALL

Inches(mm)

SIDE VIEW

WALL RING TERMINATION

(15F74) LB-49107CB for 2 in. (51) Venting

INTAKE

PIPE

EXHAUST

PIPE

9 - Position termination ends so they are free from any

obstructions and above the level of snow accumulaĆ

tion (where applicable). Termination ends must be a

minimum of 12 inches (305 mm) above grade level.

Do not point into window wells, stairwells, alcoves,

courtyard areas or other recessed areas. Do not

position termination ends directly below roof eaves

or above a walkway. Since the G32V is a certified diĆ

rect vent, Category IV gas furnace, the location of

the termination is limited by local building codes. In

the absence of local codes, refer to the current NaĆ

tional Fuel Gas Code ANSI Z223-1 in USA, and curĆ

rent standard CAN/CGA-B149.1 of the Natural Gas

Installation Instructions in Canada for details. The

termination should be at least 12 inches (305 mm)

from any opening through which flue products could

enter the building.

When horizontally vented, minimum clearance for

termination from electric meters, gas meters, regulaĆ

tors and relief equipment is 4 feet (1.2 m) for US

installations. Refer to the current CAN/CGA-B149.1

for installations in Canada or with authorities having

local jurisdiction.

Page 13

At vent termination, care must be taken to maintain

protective coatings over building materials (proĆ

longed exposure to exhaust condensate can destroy

protective coatings). It is recommended that the exĆ

haust outlet not be located within 6 feet (1.8 m) of a

condensing unit because the condensate can damĆ

age the painted coating.

IMPORTANT

Combustion air intake inlet and exhaust outlet

should not be located within 6 feet (1.8 m) of dryer

vent or combustion air inlet or outlet of another apĆ

pliance. Piping should not exit less than 3 feet (.91 m)

from opening into another building.

IMPORTANT

For Canadian Installations Only:

In accordance to CAN/CGA-B149.1 and .2, the miniĆ

mum allowed distance between the combustion air

intake inlet and the exhaust outlet of other apĆ

pliances shall not be less than 12 inches (305 mm).

10 - Suspend piping using hangers at a minimum of every

5 feet (1.52 m) for schedule 40 PVC and every 3 feet

(.91 m) for ABS-DWV, PVC-DWV, SDR-21 PVC,

and SDRĆ26 PVC piping. A suitable hanger can be

fabricated by using metal or plastic strapping or a

large wire tie.

11 - In areas where piping penetrates joists or interior

walls, hole must be large enough to allow clearance

on all sides of pipe as it passes through the center of

the hole.

12 - Isolate piping at the point where it exits the outside

wall or roof.

13 - When furnace is installed in a residence where unit is

shut down for an extended period of time, such as a

vacation home, make provisions for draining conĆ

densate collection trap and lines.

14 - Based on the recommendation of the manufacturer,

a multiple furnace installation may use a group of up

to four termination kits WTK assembled together

horizontally, as shown in figure 17.

FIGURE 14

METAL OR PLASTIC

STRAPPING

OR LARGE

WIRE TIES

FIGURE 15

FRONT VIEW

WALL TERMINATION

(22G44) LB-49107CD for 2(51) Venting

(44J40) LB-65701A for 3(76) Venting

3 (76) OR

2 (51) 90_ ELBOW

1/2 (13)

FOAM

INSULATION

Inches(mm)

3 (76) OR

2 (51) 90_ ELBOW

3 x 2 (76 x 51) OR

2 x 1-1/2 (51 x 38)

REDUCER BUSHING LOCAĆ

TION

FOR OFFSET TERMINATION

Optional Turndown

(Not Shown)

May Be Used on

Intake Only

FIGURE 16

(305)

(127)

1/2 (13) Foam

Insulation in

Unconditioned Space

EXHAUST VENT

INTAKE VENT

OUTSIDE WALL

EXHAUST VENT

INTAKE

VENT

Front View

Side View

VENT TERMINATIONS

WALL TERMINATION KIT (30G28) WTK

Inches (mm)

Page 14

FIGURE 17

EXHAUST

VENT

INTAKE VENT 5-1/2

(140)

Front View

(305)

(127)

18 MAX.

(457)

EXHAUST VENT

INTAKE

VENT

Side View

OPTIONAL VENT TERMINATION FOR

MULTIPLE UNIT INSTALLATION

WALL TERMINATION KIT WTK

Inches (mm)

FIGURE 18

12 MIN.

(305)

Above Grade

COVER EXHAUST

VENT WITH

1/2 (13)

FOAM

INSULATION

Front View

Side View

VENT TERMINATIONS

MODEL WTK WALL TERMINATION KIT (30G28)

EXTENDED VENT FOR GRADE CLEARANCE

Inches (mm)

(127)

5Ć1/2

(140)

EXHAUST

AIR

INTAKE

AIR

GRADE

(305)

8 (203)

Minimum

12 (305)

Minimum

ABOVE GRADE

INTAKE

AIR

EXHAUST

AIR

GRADE

FIGURE 19

VENT TERMINATIONS

MODEL WTKX (30G79)

EXTENSION RISER FOR GRADE CLEARANCE

(102)

8 MIN.

(203)

EXHAUST VENT

INTAKE

VENT

GRADE

EXHAUST

VENT

INTAKE

VENT

(864)

(305)

(229)

NOTE - Enclosed exhaust pipe is

insulated with 1/2 inch (13 mm)

foam insulation. If intake and exĆ

haust pipes are reversed, slit and

remove foam insulation and

reapply to other vent. Exhaust

vent must be insulated.

Front View

Side View

OUTSIDE WALL

Inches (mm)

G32 VENTING IN EXISTING CHIMNEY

FIGURE 20

8 in. - 12 in.

(203 mm - 305 mm)

3 in. - 8 in.

(76 mm-

203 mm)

3 in. - 8 in.

(76 mm-

203 mm)

NOTE - Do not discharge exhaust gases directly into any chimney or vent stack.

If vertical discharge through an existing unused chimney or stack is required,

insert piping inside chimney until the pipe open end is above top of chimney and

terminate as illustrated. In any exterior portion of chimney, the exhaust vent

must be insulated.

STRAIGHT CUT OR

ANGLE CUT IN DIRECTION

OF ROOF SLOPE

EXHAUST VENT

1/2" (13 mm)

WEATHERPROOF

INSULATION

SHOULDERS OF FITTINGS

PROVIDE SUPPORT FOR

PIPE ON TOP PLATE

ALTERNATE

INTAKE VENT

EXTERIOR

PORTION

OF CHIMNEY

INTAKE VENT

INSULATION

(OPTIONAL)

TOP PLATE

(18 GA. MIN.)

MIN. 12" (304 mm)

ABOVE ROOF

INSULATE

TO FORM

SEAL

Page 15

Condensate Piping

This unit is designed for either right- or left-side exit of

condensate piping. Route the condensate drainline only

within the conditioned space: this prevents possible

freezing of the condensate, which would block the drain-

line. Use an electric heat cable if you route the conden-

sate line through unconditioned areas.

CAUTION

Do not use copper tubing or existing copper conĆ

densate lines for drain line.

1 - Determine which side of the unit that the condensate

will exit.

2 - Connect 1/2" (13 mm) plastic pipe plug (provided) in

the unused end of the condensate trap. Install plug

so that it is sealed water tight yet able to be removed.

Do not permanently seal the connection. Teflon tape

is recommended to seal joint. See figure 21.

CONDENSATE ASSEMBLY

(For left or right installation)

FIGURE 21

COLD

HEADER

BOX

NIPPLE

ADAPTER

NIPPLE PLUG

COMBUSTION AIR

BLOWER BRACKET

CONDENSATE TRAP

ELBOW

BOOT OR CAP

3 - Use the provided adapter (1/2" mpt X 3/4" PVC) and

a field-provided nipple to carry drainage outside the

cabinet. A 1/2" CPVC x 1/2" MPT adapter and 1/2"

CPVC is acceptable for use.

4 - Glue nipple to the adapter using the procedures out-

lined in the Joint Cementing Procedures" section.

The nipple/adapter assembly should be connected

in a non-permanent manner and must be water tight.

Teflon tape is recommended to seal the joint.

Right-Hand Side Condensate Exit:

Install the nipple/adapter assembly from the outĆ

side of the cabinet and insert the adapter into the

threaded opening in the condensate trap.

Left-Hand Side Condensate Exit:

Insert nipple/adapter assembly from the left-hand

side of the cabinet and through the combustion air

blower mounting structure into the threaded

opening in the condensate trap.

5 - Connect field-supplied plumbing to nipple and route

to open drain. Plumbing should be vented to a point

higher than the condensing coil. See figure 22.

FIGURE 22

CONDENSATE PLUMBING

(Plumbing must be vented higher than coil.)

6 - Connect condensate drain line [1/2" (13 mm) SDR 11

plastic pipe or tubing] to condensate connection on

condensate trap assembly and route to open drain.

Condensate line must be sloped downward away

from condensate trap to the drain. If drain level is

above condensate outlet, use a condensate pump to

pump condensate to the higher level. Condensate

drain line should be routed within the conditioned

space to avoid freezing of condensate and blockage

of drain line. If this is not possible, a heat cable kit

may be used on the condensate trap and condenĆ

sate line. Heating cable kit is available from Lennox

in various lengths; 6 feet (1.8 m) - kit no. 26K68; 24

feet (7.3 m) - kit no. 26K99; and 50 feet (15.2 m) - kit

no. 26K70. Also available from Lennox: 1/2" (12.7

mm) glass fiber tape - 39G04; 2" (50.8 mm) plum foil

tape - 39G03.

Page 16

Gas Piping

CAUTION

If a flexible gas connector is required or allowed by

the authority that has jurisdiction, black iron pipe

shall be installed at the gas valve and extend outĆ

side the furnace cabinet.

1 - Gas piping may be routed into the unit through either

the left- or right-hand side. Supply piping enters into

the gas valve from the bottom of the valve as shown

in figure 23.

2 - When connecting the gas supply, factors such as

length of run, number of fittings and furnace rating

must be considered to avoid excessive pressure

drop. Table 6 lists recommended pipe sizes for typiĆ

cal applications.

NOTE - Use two wrenches when connecting gas pipĆ

ing to avoid transferring torque to the manifold.

3 - The gas piping must not run in or through air ducts,

clothes chutes, gas vents or chimneys, dumb waitĆ

ers, or elevator shafts. Center gas line through piping

hole. Gas line should not touch side of unit. When

left-hand gas plumbing is required, gas line should

be installed in the lower half of knockout so that pip-

ing will clear combustion air blower. See figure 23.

FIGURE 23

GAS VALVE

LEFT SIDE PIPING

MANUAL MAIN

SHUT-OFF

VALVE

RIGHT SIDE PIPING

(STANDARD)

GAS VALVE

1/8 in. NPT

PLUGGED

TAP

MANUAL MAIN

SHUT-OFF

VALVE

1/8 in. NPT

PLUGGED

TAP

4 – The piping should be sloped 1/4 inch (6.4 mm) per 15

feet (4.57 m) upward toward the meter from the furĆ

nace. The piping must be supported at proper interĆ

vals [every 8 to 10 feet (2.44 to 3.01 m)] using suitĆ

able hangers or straps. A drip leg should be installed

in vertical pipe runs to the unit.

5 - In some localities, codes may require installation of a

manual main shutĆoff valve and union (furnished by

the installer) external to the unit. Union must be of the

ground joint type.

NOTE - Install a 1/8 inch NPT plugged tap in the field pipĆ

ing upstream of the gas supply connection to the unit. The

tap must be accessible for test gauge connection. See

figure 24.

FIGURE 24

MANUAL MAIN SHUT-OFF

VALVE WILL NOT HOLD

NORMAL TEST PRESSURE

CAP

FURNACE

ISOLATE

GAS VALVE

1/8 in. (3.2 mm) NPT

PLUGGED TAP

Leak Check

After gas piping is completed, carefully check all piping

connections (factory- and field-installed) for gas leaks.

Use a leak detecting solution or other preferred means.

IMPORTANT

Some soaps used for leak detection are corrosive

to certain metals. Carefully rinse piping thoroughly

after leak test has been completed. Do not use

matches, candles, flame, or other sources of igniĆ

tion to check for gas leaks.

IMPORTANT

The furnace must be isolated from the gas supply

piping system by closing its individual manual

shut-off valve during any pressure testing of the

gas supply piping system at test pressures equal

to or less than 1/2 psig (3.45 kPa). See figure 24.

The furnace and its individual shut-off valve must

be disconnected from the gas supply piping sysĆ

tem during any pressure testing of the system at

test pressures greater than 1/2 psig (3.45 kPa).

Page 17

TABLE 6

GAS PIPE CAPACITY - ft.3/hr (m3/hr)

Nominal Internal Length of Pipe-Feet (m)

Nominal

Iron Pipe Size

-Inches(mm)

Internal

Diameter

-Inches(mm) 10

(3.048)

(6.096)

(9.144)

(12.192)

(15.240)

(18.288)

(21.336)

(24.384)

(27.432)

100

(30.480)

1/4

(6.35)

.364

(9.246)

(1.13)

(.82)

(.68)

(.57)

(.51)

(.45)

(.42)

(.40)

(.37)

(.34)

3/8

(9.53)

.493

(12.522)

(2.69)

(1.84)

(1.47)

(1.27)

(1.13)

(1.02)

(.73)

(.88)

(.82)

(.76)

1/2

(12.7)

.622

(17.799)

175

(4.96)

120

(3.40)

(2.75)

(2.32)

(2.07)

(1.87)

(1.73)

(1.61)

(1.50)

(1.42)

3/4

(19.05)

.824

(20.930)

360

(10.19)

250

(7.08)

200

(5.66)

170

(4.81)

151

(4.28)

138

(3.91)

125

(3.54)

118

(3.34)

110

(3.11)

103

(2.92)

(25.4)

1.049

(26.645)

680

(19.25)

465

(13.17)

375

(10.62)

320

(9.06)

285

(8.07)

260

(7.36)

240

(6.80)

220

(6.23)

205

(5.80)

195

(5.52)

1-1/4

(31.75)

1.380

(35.052)

1400

(39.64)

950

(26.90)

770

(21.80)

660

(18.69)

580

(16.42)

530

(15.01)

490

(13.87)

460

(13.03)

430

(12.18)

400

(11.33)

1-1/2

(38.1)

1.610

(40.894)

2100

(59.46)

460

(41.34)

1180

(33.41)

990

(28.03)

900

(25.48)

810

(22.94)

750

(21.24)

690

(19.54)

650

(18.41)

620

(17.56)

(50.8)

2.067

(52.502)

3950

(111.85)

2750

(77.87)

2200

(62.30)

1900

(53.80)

1680

(47.57)

1520

(43.04)

1400

(39.64)

1300

(36.81)

1220

(34.55)

1150

(32.56)

2-1/2

(63.5)

2.469

(67.713)

6300

(178.39)

4350

(123.17)

3520

(99.67)

3000

(84.95)

2650

(75.04)

2400

(67.96)

2250

(63.71)

2050

(58.05)

1950

(55.22)

1850

(52.38)

(76.2)

3.068

(77.927)

11000

(311.48)

7700

(218.03)

6250

(176.98)

5300

(150.07)

4750

(134.50)

4300

(121.76)

3900

(110.43)

3700

(104.77)

3450

(97.69)

3250

(92.03)

(101.6)

4.026

(102.260)

23000

(651.27)

15800

(447.39)

12800

(362.44)

10900

(308.64)

9700

(274.67)

8800

(249.18)

8100

(229.36)

7500

(212.37)

7200

(203.88)

6700

(189.72)

NOTE - Capacity given in cubic feet (m3) of gas per hour and based on 0.60 specific gravity gas.

Electrical

A field make-up box is provided for line voltage wiring.

Line voltage wiring to unit is done through the J69 jack

from the field make-up box to plug P69 from the control

box. See figures 25 and 26 for make-up box installation.

Refer to figure 27 for schematic wiring diagram and trouĆ

bleshooting, figure 28 for point-to-point field wiring and

figure 29 for a detailed illustration of the Surelight inteĆ

grated control.

ELECTROSTATIC DISCHARGE (ESD)

Precautions and Procedures

CAUTION

Electrostatic discharge can affect electronic comĆ

ponents. Take precautions during furnace installaĆ

tion and service to protect the furnace's electronic

controls. Precautions will help to avoid control exĆ

posure to electrostatic discharge by putting the

furnace, the control and the technician at the same

electrostatic potential. Neutralize electrostatic

charge by touching hand and all tools on an unĆ

painted unit surface, such as the gas valve or blowĆ

er deck, before performing any service procedure.

1 - Select circuit protection and wire size according to

the unit nameplate. The power supply wiring must

meet Class 1 restrictions.

2 - A snaphole bushing is provided to seal around the

wiring as it enters the cabinet. A snaphole plug is proĆ

vided to seal the unused wire entry hole.

3 - Install a separate disconnect switch (protected by eiĆ

ther a fuse or circuit breaker) near the unit so that

power can be turned off for servicing.

4 - Install field makeĆup box on either side, inside or out

of the cabinet. Knockouts are provided in box and

cabinet to facilitate wiring. See figures 25 and 26.

To ensure proper grounding of the furnace, two lockĆ

washers are included in the electrical make-up box

bag assembly. Place each lockwasher on a securing

screw before installing the make-up box. Make sure

the lockwasher breaks the paint on the cabinet so

that the washer is touching metal. Unit is not properly

grounded if paint has not been removed by the lockĆ

washer.

5 - Remove cap from knockout in blower deck on the

same side as the installed make-up box.

6 - Insert the three-pin (P69) plug from the control box

into the knockout provided in the blower deck.

7 - Connect jack (J69) from make-up box to jack plug in

blower deck.

8 - Before connecting the thermostat or the power wirĆ

ing, check to make sure the wires will be long enough

for servicing at a later date. Remove the blower acĆ

cess panel to check the length of the wire.

9 - Electrically ground unit in accordance with local

codes or, in the absence of local codes, according to

the current National Electric Code (ANSI/NFPA No.

70) and in Canada with the current Canadian Electric

Code part 1 (CSA standard C22.1). The ground wire

is provided in the field make-up box.

Page 18

IMPORTANT

Ignition control will not operate unless unit is propĆ

erly grounded. 120V supply must be installed with

correct polarity.

CAUTION

Bundle all wires connected to control board in

such a way that drip loops are formed. Drip loops

direct damaging moisture away from control

board.

INTERIOR MAKE-UP BOX INSTALLATION

P69 from

Control Box

J69

MAKE-UP

BOX

BUSHING

FIGURE 25

FIGURE 26

EXTERIOR MAKEĆUP BOX INSTALLATION

P69 from

Control Box

J69

MAKE-UP

BOX

BUSHING

10 -One line voltage EAC" terminal is provided on the

furnace control board. Any electronic air cleaner

rated up to one amp can be connected to this termiĆ

nal with the neutral leg of the circuit being connected

to the neutral EAC" terminal. See figure 29 for conĆ

trol board configuration. This terminal is energized

when the indoor blower is operating.

11 -One line voltage HUM" terminal is provided on the

furnace control board. Any humidifier rated up to one

amp can be connected to this terminal with the neuĆ

tral leg of the circuit being connected to the neutral

HUM" terminal. See figure 29 for control board conĆ

figuration. This terminal is energized in the heating

mode whenever the combustion air inducer is operĆ

ating.

12 - Install room thermostat according to instructions

provided with thermostat. The furnace may be conĆ

trolled by either a single- or two-stage thermostat. If

furnace is being used with heat pump refer to FM21

installation instruction.

13 - Complete wiring connections to equipment using

wiring diagrams provided with unit and figures 27

and 28. Use 18-gauge wire or larger that is suitable

for Class II rating for thermostat connections. See

table 7 for diagrams for specific applications.

Indoor Blower Speeds

1 - When the thermostat is set to FAN ON," the indoor

blower will run continuously at approximately 38% of

the second-stage cooling speed when there is no

cooling or heating demand.

2 - When the G32V unit is running in the heating mode,

the indoor blower will run on the heating speed desigĆ

nated by the positions of dip switches 11 and 12.

3 - When there is a cooling demand, the indoor blower

will run on the cooling speed designated by the posiĆ

tions of dip switches 5 and 6.

Page 19

TYPICAL G32V SCHEMATIC WIRING DIAGRAM

FIGURE 27

Page 20

TYPICAL G32V FIELD WIRING DIAGRAM

FIGURE 28

TABLE 7

Field Wiring Applications

Jumper Settings (See figure 29)

Thermostat E20 Term. Strip

Y1 to Y2 W914 W951 Wiring Connections

1 Heat / 1 Cool

NOTE - Use dip

switch 3 to set

second-stage

heat ON delay.

ON-10 minutes.

OFF-15 minĆ

utes.

SINGLE Yes Intact Intact S1

T'STAT

CONTROL

TERM. STRIP

OUTDOOR

UNIT

1 Heat / 1 Cool

with CCB1

NOTE - Use dip

switch 3 to set

second-stage

heat ON delay.

ON-10 minutes.

OFF-15 minĆ

utes.

SINGLE Yes Cut Intact S1

T'STAT

CONTROL

TERM. STRIP

OUTDOOR

UNIT

CCB1

Page is loading ...

Lennox G32 Installation guide

Brand: Lennox

Model: G32

Category: Water heaters & boilers

Type: Installation guide

This manual is also suitable for

G32V5-100

Download PDF

report

Lennox G32 Installation guide

This manual is also suitable for

Lennox G32 Installation guide

Related papers

Other documents