Logik L40LCD11 User manual

40” HD Ready 1080p Digital LCD TV

Instruction Manual

L40LCD11

Contents

Preparation .........................................................................................................................................................................................5

Unpacking the TV ...............................................................................................................................................................................................................5

Installing / Removing the Base Stand .........................................................................................................................................................................6

Front / Right Side View and Controls ...........................................................................................................................................................................7

Rear View and Sockets ......................................................................................................................................................................................................8

Installing Batteries in the Remote Control ................................................................................................................................................................9

Remote Control Operation Range ................................................................................................................................................................................9

Remote Control .................................................................................................................................................................................................................10

Connections ......................................................................................................................................................................................13

Making Video and Audio Connections .....................................................................................................................................................................13

Connecting an AV Device with an HDMI Cable .....................................................................................................................................................13

Connecting a Computer with a VGA Cable .............................................................................................................................................................14

Connecting an AV Device with a Component (YPbPr) Cable ...........................................................................................................................14

Connecting an AV Device with a SCART Cable ......................................................................................................................................................15

Connecting an AV Device with Composite Cable .................................................................................................................................................15

Connecting a Coaxial Audio Receiver .......................................................................................................................................................................16

Connecting Earphones ...................................................................................................................................................................................................16

Connecting a USB Storage Device ..............................................................................................................................................................................17

Connecting the Aerial .....................................................................................................................................................................................................17

Initial Setup ......................................................................................................................................................................................18

Turning the TV on for the First Time ..........................................................................................................................................................................18

− Selecting the Input Source................................................................................................................................................................................19

− Display Channel Information ...........................................................................................................................................................................19

− Volume Adjustment .............................................................................................................................................................................................19

Using the Features ...........................................................................................................................................................................20

Customising the Channel Setting (TV, DTV or Radio Mode) ............................................................................................................................ 20

− Auto Tuning (ATV / DTV mode)....................................................................................................................................................................... 20

− ATV Manual Tuning (ATV mode) .....................................................................................................................................................................21

− DTV Manual Tuning (DTV mode) ....................................................................................................................................................................21

− Channel Edit (ATV Mode) .................................................................................................................................................................................. 22

− Channel Edit (DTV Mode) .................................................................................................................................................................................. 23

− Signal Information (DTV Mode) ...................................................................................................................................................................... 24

− CI (Common Interface) (DTV Mode) .............................................................................................................................................................. 24

− Software Update (Over Air Download) (DTV mode) .............................................................................................................................. 25

− Software Update (USB) ...................................................................................................................................................................................... 26

Customising the Picture Setting ................................................................................................................................................................................ 26

Customising the Sound Setting ................................................................................................................................................................................. 28

− Stereo / Dual Sound Reception (ATV Mode) .............................................................................................................................................. 29

− Speaker Sound Output Selection (DTV Mode) ......................................................................................................................................... 29

Customising the Time Settings................................................................................................................................................................................... 29

Customising the Option Setting .................................................................................................................................................................................31

− OSD Language .......................................................................................................................................................................................................31

− TT Language ...........................................................................................................................................................................................................31

− Audio Language (DTV Mode) .......................................................................................................................................................................... 32

− Subtitle Language (DTV Mode) ...................................................................................................................................................................... 33

− Hearing Impaired ................................................................................................................................................................................................. 33

− PVR File System (DTV Mode) ............................................................................................................................................................................ 34

− Aspect Ratio ........................................................................................................................................................................................................... 35

− Blue Screen ............................................................................................................................................................................................................ 36

− Backlight ................................................................................................................................................................................................................. 36

− HDMI CEC (Consumer Electronics Control) (HDMI Mode) .................................................................................................................... 37

− Restore Factory Default ..................................................................................................................................................................................... 38

Customising the LOCK Setting .................................................................................................................................................................................... 38

− Lock System ........................................................................................................................................................................................................... 38

− Set Password ......................................................................................................................................................................................................... 39

− Block Channel .......................................................................................................................................................................................................40

− Parental Guidance ................................................................................................................................................................................................41

− Key Lock .................................................................................................................................................................................................................. 42

Teletext (ATV Mode) ........................................................................................................................................................................................................ 43

− To Turn on Teletext Function........................................................................................................................................................................... 43

Digital Teletext (DTV Mode) ......................................................................................................................................................................................... 44

− Teletext within Digital Service ........................................................................................................................................................................ 44

EPG (Electronic Programme Guide) (DTV Mode) .................................................................................................................................................44

− Switch On / O EPG ............................................................................................................................................................................................. 44

− Select a Programme ........................................................................................................................................................................................... 45

Using the Features via USB Port .....................................................................................................................................................46

Photo .................................................................................................................................................................................................................................... 46

Music ..................................................................................................................................................................................................................................... 46

Movie .................................................................................................................................................................................................................................... 47

Text ........................................................................................................................................................................................................................................ 48

PVR (Personal Video Recorder) .......................................................................................................................................................49

Time Shift Function (DTV Mode) ................................................................................................................................................................................ 49

Recording DTV Programme onto a USB Storage Device .................................................................................................................................. 50

Timer Programming ....................................................................................................................................................................................................... 50

Play Recorded Programme ...........................................................................................................................................................................................51

Maintenance .....................................................................................................................................................................................53

Display Modes ..................................................................................................................................................................................55

YPbPr Mode ....................................................................................................................................................................................................................... 55

PC Mode .............................................................................................................................................................................................................................. 55

HDMI Mode ....................................................................................................................................................................................................................... 55

Specifications ...................................................................................................................................................................................56

Safety Warnings ...............................................................................................................................................................................57

GB

5

Preparation

Unpacking the TV

Remove all packaging from the TV. Retain the packaging. If you dispose of it please do so according to local regulations.

The following items are included:

Screw A x 6

(P.N.: I.03.TW4016A01)

AV Cable

(P.N.: E.14.113150013)

Remote Control / AAA Batteries x 2

(P.N.: I.14.000000760 & E.17.101570001)

Instruction Manual

(P.N.: I.08.141406901)

Quick Start Guide

(P.N.: I.08.246406901)

Digital TV Switchcover Addendum

(P.N.: I.08.557724771)

Thank you for purchasing your new Logik 40" HD Ready 1080p Digital LCD TV.

Your new TV has many features and incorporates the latest technology to enhance your viewing

experience. We recommend that you spend some time reading this instruction manual in order that you

fully understand these features. You will also find some hints and tips to help you resolve any issues.

Read all the safety instructions carefully before use and keep this instruction manual for future reference.

If items are missing, or damaged please contact Partmaster (UK only). Tel: 0844 800 3456 for assistance.

Preparation

Video

R

L

TV

TV Base

(P.N.: I.01.540406903)

GB

6

Preparation

4. The 6 screw holes should now be aligned screw in the 6

screws to fix the base stand to the TV.

6. Mounting on the wall. This TV is designed to be wall-

mounted with a standard 400 mm x 200 mm mounting

kit designed for flat-panel TVs (sold separately). Mount

this TV according to the instructions included in the

mounting kit. Due to space restrictions, we recommend

that you make all connections (refer to page 13-17 for

details) before mounting on to the wall.

3. To install the base stand first make sure you position the

front of the base stand at the front of the TV. Align the 2

plugs with the 2 locator holes. There is only one way for

the base stand to connect to the TV.

5. To remove the base stand, lay the TV down on a flat

surface with the back side facing up. Please make sure

to place a soft cushioned material (such as a pillow or

thick piece of foam) beneath the screen. Untighten the 6

screws that hold the base stand to the rear of the TV. Slide

the base stand out.

1. Disconnect all cables connected to the TV.

2. Lay the TV down on a flat surface with the back side

facing up. Please make sure to place a soft cushioned

material (such as a pillow or thick piece of foam) beneath

the screen.

plugs

locator

holes

Installing / Removing the Base Stand

Screws x 3

(P.N.: xxxxxxxxxxx)

screw

Screw A x 6

(P.N.: I.03.TW4016A01)

400 mm

200 mm

Four mounting holes

(size M5 screw)

• Please read this instruction manual carefully while setting up your TV.

• If you require additional assistance please call our UK Call Centre on 0844 561 1234. Our UK

Customer Contact Centre is open Monday-Saturday 8am-8pm or Sunday 8am-6pm.

Keep all the spare screws should you want

to use the base stand option.

The screw holes will only align if the front

of the base stand is at the front of the TV.

• Remove the base stand before mounting the TV onto the wall.

• The LCD display is very fragile, and must be protected at all times when installing and removing the base stand. Be

sure that no hard or sharp object, or anything that could scratch or damage the LCD display, comes into contact with

it. DO NOT exert pressure on the front of the TV at any time because the screen could crack.

unscrew

Screw A x 2

(P.N.: I.03.TW4016A01)

Screw B x 4

(P.N.: I.03.MW4012001)

GB

7

Preparation

Front / Right Side View and Controls

Item Description

1 IR (Infrared Receiver)

Receives IR signals from the remote control.

Do not put anything near the sensor, as its function may be affected.

2 POWER LED

Illuminates blue when the TV is turned on. Illuminates red when the TV is in standby

mode. The LED will illuminate blue when the timer programming has started in the

standby mode.

3 VOL + / –

Adjusts the volume.

Press to select and adjust a setting in the OSD menu.

4 CH

/ Press to select a channel or select a sub-menu from the OSD menu.

5 MENU Displays the OSD (on screen display) menu.

6 SOURCE

Press to select among different input signal sources:

DTV / ATV / AV / SCART / YPBPR / HDMI1 / HDMI2 / HDMI3 / PC / MEDIA.

Confirmed the selection on OSD menu.

7

/ I

Switches the TV on from standby mode.

Switches the TV back to standby mode.

3

4

5

6

7

1 2

GB

8

Preparation

Rear View and Sockets

Socket Description

1 POWER ON/OFF Switch on the POWER ON/OFF switch to turn the TV to standby mode.

2 AC Connects the mains cable to the mains socket.

3 USB

Allows the insertion of a USB storage device to play video, audio, photo and text files

(Media mode) and record DTV programmes on to a USB storage device.

4 HDMI1 / 2 / 3

To connect to a High-Definition (HD) signal output device, such as a set-top box, blu-ray

disc player or AV receiver.

5 VGA / PC AUDIO To connect to a computer or other devices with a VGA interface.

6 CI (Common Interface) Slot Allows the insertion of a Common Access Module. (Refer to page 24 for details)

7 SCART To connect to a VCR, DVD Player, or other AV device with a SCART output socket.

8 COAXIAL To connect to the audio socket on the digital/standard 5.1 audio system.

9 Y, PB, PR / AUDIO (L/R)

To connect to a DVD player, Digital Set-Top-Box, or other AV devices with component

(YPbPr) video and audio output sockets.

10 VIDEO / AUDIO (L/R)

To connect to the Composite VIDEO and AUDIO (L/R) output sockets on external video

devices.

11 RF To connect to the aerial socket on the wall with the RF coaxial cable.

12

To connect to the earphones.

HDMI1

HDMI3

HDMI2

POWER

ON/OFF

AC

4 5 71 2 3 8 11 1210

96

GB

9

Preparation

Remote Control Operation Range

Point the remote control at the TV no more than 5 metres from the

remote control sensor on the TV and within 60° in front of the TV.

The operating distance may vary depending on the brightness of the

room.

Installing Batteries in the Remote Control

1. Press and lift the back cover to open the battery compartment of the

remote control.

2. Insert two AAA size batteries. Make sure to match the (+) and ( - ) ends

of the batteries with the (+) and ( - ) ends indicated in the battery

compartment.

3. Close the battery compartment cover.

Handling the Batteries

• Improper or incorrect use of batteries may cause

corrosion or battery leakage, which could cause

fire, personal injury or damage to property.

• Only use the battery type indicated in this

manual.

• When the batteries are exhausted, the remote will

not function. Replace both batteries at the same

time with new ones.

• Do not install new batteries with used ones and

do not mix different types of batteries.

• Do not dispose of used batteries as domestic

waste. Dispose of them in accordance with local

regulations.

Handling the Remote Control

• Take care of your fingernails when you press and

hold the battery release tab.

• Do not drop or cause impact to the remote

control.

• Do not spill water or any liquid on the remote

control.

• Do not place the remote control on a wet object.

• Do not place the remote control under direct

sunlight or near sources of excessive heat.

• Remove the battery from the remote control

when not in use for a long period of time, as it

could cause corrosion or battery leakage and may

result in physical injury and/or property damage

including fire

30° 30°

5M

GB

10

Preparation

1.

Switches the TV between on and standby mode.

2.

MUTE

Mutes and restores your TV sound.

3. 0-9 Number Button

Press to select a programme. (ATV / DTV mode)

Select numbered items in a menu. (DVD mode)

4. LIST

• Display channel list. (ATV / DTV mode)

• Press to select a track number above 10. For example, to

select track 23 press twice followed by 3. (DVD mode)

5.

RECALL

Return to the previous viewing channel. (ATV / DTV mode)

6. SLEEP

Sets the TV sleep timer: OFF / 10 / 20 / … / 180 / 240 min.

7. VOL + / –

Adjusts the volume.

8. CH + / –

Select a channel.

9.

• Display the present channel information such as the current

time and channel name. (ATV / DTV mode)

• Display the present disc information. (DVD mode)

10. S.MODE

Select sound mode: Standard / Music / Movie / Sports /

Personal.

11. ASPECT

Allows you to watch the screens in various formats: Auto / 4:3

/ 16:9 / Zoom / Smart Zoom / Dot to Dot / Subtitle. (Dot to Dot

only operates in YPBPR / HDMI mode)

12. GUIDE

Displays the EPG (Electronic Programme Guide). (DTV mode)

TITLE

Displays the DVD title content. (DVD mode)

13. P.MODE

Select picture mode: Dynamic / Standard / Mild / Personal.

14. MENU

Display the OSD (On Screen Display) menu.

15. INPUT

Select among the dierent input signal sources:

DTV / ATV / AV / SCART / YPBPR / HDMI1 / HDMI2 / HDMI3 / PC /

MEDIA.

16.

Allows you to navigate the OSD menus and adjust the system

settings to your preference.

OK

Conrm the selection in the OSD menus.

17. BACK

Return to the previous menu in the OSD menus.

18. Exit

Exit the OSD menu.

Remote Control

1

2

5

8

12

15

18

9

13

3

4

7

11

14

16

17

6

10

Please note that there are DVD mode functions on the remote control only operate on

TV models with a built-in DVD player.

GB

11

Preparation

19. FAV

Display the favourite channel list. (ATV / DTV mode)

SETUP

Display and exit the DVD setup menu. (DVD mode)

20.

To turn on / o the SRS Tru Surround HD function.

21. TV.RD

A short-cut to switch input source to TV / Digital radio

channels. (DTV mode)

Eject a disc. (DVD mode)

22. AD (Audio Description)

To turn on / o the Audio Description (AD) function (only

applicable when the TV programme has this feature).

(DTV mode)

23. ANGLE

Select dierent angles for the video. (DVD mode)

24. STEP

To play the playback forward frame by frame. (DVD

mode).

25. ZOOM

Zoom in on the displayed frame. (DVD mode)

26.

REC

Record the current programme. (DTV mode)

27.

• To start the timeshift playback. (DTV mode)

• To start playback or pause. (Media / DVD mode)

28. PROG

Programme the DVD. (DVD mode)

29.

Stop

To stop the playback or recording. (DVD / Media mode)

30. T.SHIFT

Start the time-shift function (DTV mode)

31.

TEXT

Turns on and o the teletext function. (ATV / DTV mode)

To reverse playback rapidly. (DVD / Media mode)

32.

CANCEL

To exit the teletext mode. (ATV mode)

To advance playback rapidly. (DVD / Media mode)

33. S (Subtitle)

• Selects subtitles which are broadcast with the

programme. (DTV mode).

• Selects subtitles on the DVD. (DVD mode)

34.

SIZE

To enlarge the picture on the TV in teletext. (ATV mode)

26

30

33

34

24

25

29

28

32

31

2220

2119

23

27

Please note that there are DVD mode functions on the remote control only operate on

TV models with a built-in DVD player.

GB

12

Preparation

35. REVEAL

Reveals hidden information such as the answer to a quiz

in teletext. (ATV mode).

To skip to the beginning of the next chapter / track /

photo. (DVD / Media mode)

36.

HOLD

Freezes a multi-page passage on screen in teletext. (ATV

mode)

To skip to the beginning of the previous chapter / track /

photo. (DVD / Media mode)

37.

SUBPAGE

Displays the subpage on the teletext screen. (ATV mode)

MENU

Display the DVD menu. (DVD mode)

38.

INDEX

To select the page number of the index from teletext.

(ATV mode)

AUDIO

• Switches between the audio languages (only

applicable when the TV programme / disc has this

features.) (DTV / DVD mode)

• Select stereo / Dual Sound Reception. (ATV mode)

39. Coloured buttons

Access the TELETEXT items or channel edit when using

Digital / Freeview TV Channels. (ATV / DTV mode)

GOTO (RED)

To skip to a specic location on a DVD / CD. (DVD mode)

SLOW (GREEN)

Play video slow. (DVD mode)

REPEAT (YELLOW)

Select between dierent repeat modes. (DVD mode)

A–B (BLUE)

Repeat a segment between A and B. (DVD mode)

38

37

36

39

35

Please note that there are DVD mode functions on the remote control only operate on

TV models with a built-in DVD player.

GB

13

Connections

Connecting an AV Device with an HDMI Cable

• This TV can accept High-Definition Multimedia Interface (HDMI) supports HDCP (High-Bandwidth Digital Content Protection)

Protocol.

• The TV has a total of 3 HDMI input sockets, please make sure the correct input source is selected corresponding to your

connected HDMI input socket.

• When you connect to the output of an HD ready player (blu-ray disc player, game console, set-top box or computer) switch to

the HDMI function and the TV will automatically detect the resolution used by the HDMI source.

• To get the best picture quality, adjust the blu-ray disc player, game console or set-top box output resolution up to 1920 x

1080p.

1. Use a HDMI cable to connect the TV’s HDMI1 / HDMI2

/ HDMI3 input socket to the external AV device’s HDMI

output socket.

2. Plug the connected devices into the mains socket

before switching on the POWER ON/OFF switch

which is located the rear of the TV next to the mains

cable.

3. Press the

/ I button at the front right side of the

TV or the

button on the remote control to turn on

your TV.

4. Press the SOURCE button at the front right side of

the TV or the INPUT button on the remote control to

display the Source List. Use the

buttons to select

HDMI1 or HDMI2 or HDMI3 and then press the OK

button to confirm.

Making Video and Audio Connections

Not all AV devices have the ability to connect to a TV, please refer to the owner’s manual of your AV device for compatibility and

connection procedures.

When connecting any external AV device, do not connect the mains cable to the mains socket until all other connections are

complete.

Signal Type

Separate Audio

Connection Required

HDMI

(480i/480p/576i/576p/720p/1080i/1080p)

No

VGA

Yes

Component Video

(480i/480p/576i/576p/720p/1080i/1080p)

Yes

SCART (RGB Input) No

Composite Video

Yes

Best Video

Performance

Connections

Although this TV is able to connect to a HDMI

device, it is possible that some devices may

not operate correctly.

Rear View of TV

HDM I1

HDM I3

HDM I2

POW ER

ON/ OFF

AC

Blu-ray Player / DVD Player /

Recorder

Set-top Box

Game Console

HDMI Cable

(not included)

GB

14

Connections

Connecting an AV Device with a Component (YPbPr) Cable

1. Use a component cable to connect the TV’s YPbPr

input sockets to an external AV device’s component

output sockets.

2. Use an AV cable to connect the TV’s AUDIO(L/R) input

sockets to the external AV device’s component audio

output sockets. (Audio Left = white, and Audio Right

= red)

Component port on the TV Y Pb Pr

Video output ports on DVD

player

Y Pb Pr

Y Cb Cr

3. Plug the connected devices into the mains socket

before switching on the POWER ON/OFF switch

which is located at the rear of the TV next to the

mains cable.

4. Press the

/ I button at the front right side of the

TV or the

button on the remote control to turn on

your TV.

5. Press the SOURCE button at the front right side of

the TV or the INPUT button on the remote control to

display the Source List. Use the

buttons to select

YPbPr and then press the OK button to confirm.

Connecting a Computer with a VGA Cable

1. Use a VGA cable to connect the TV’s VGA input

socket to a computer’s VGA output socket. Use an

audio cable to connect the TV’s PC AUDIO input

socket to the computer’s audio output socket.

2. Plug the connected devices into the mains socket

before switching on the POWER ON/OFF switch

which is located at the rear of the TV next to the

mains cable.

3. Press the

/ I button at the front right side of the

TV or the

button on the remote control to turn on

your TV.

4. Press the SOURCE button at the front right side of

the TV or the INPUT button on the remote control to

display the Source List. Use the

buttons to select

PC and then press the OK button to confirm.

• The best resolution is 1920 x 1080.

• If your computer is set to shut down after a

few minutes of idle mode, the TV will also

switch to standby due to no signal being

received, this is to save energy. Press the

/I button at the front right side of the TV

or the

button on the remote control to

restart the TV.

Rear View of TV

VGA Cable

(not included)

Audio Cable

(not included)

HDM I1

HDM I3

HDM I2

POW ER

ON/ OFF

AC

Computer

Rear View of TV

HDM I1

HDM I3

HDM I2

POW ER

ON/ OFF

AC

L

R

COMPONENT

OUT

Y

Pr

Pb

Satellite Receiver

Video Camera

Blu-ray Player / DVD Player /

Recorder

Set-top Box

Game Console

AV Cable

(included)

Pb/Cb

Y

Pr/Cr

Y

Component

Cable

(not included)

Yellow (Video)

White (L)

Red (R)

Yellow (Video)

Red (R)

White (L)

GB

15

Connections

Connecting an AV Device with Composite Cable

1. Use the supplied AV cable to connect the TV’s

AUDIO(L/R)/VIDEO input sockets to an external AV

device’s composite audio/video sockets. (Video =

yellow, Audio Left = white, and Audio Right = red)

2. Plug the connected devices into the mains socket

before switching on the POWER ON/OFF switch

which is located at the rear of the TV next to the

mains cable.

3. Press the

/ I button at the front right side of the

TV or the

button on the remote control to turn on

your TV.

4. Press the SOURCE button at the front right side of

the TV or the INPUT button on the remote control to

display the Source List. Use the

buttons to select

AV and then press the OK button to confirm.

Connecting an AV Device with a SCART Cable

1. Use a SCART cable to connect the TV’s SCART input

socket to an external AV device’s SCART output

socket.

2. Plug the connected devices into the mains socket

before switching on the POWER ON/OFF switch

which is located at the rear of the TV next to the

mains cable.

3. Press the

/ I button at the front right side of the

TV or the

button on the remote control to turn on

your TV.

4. The TV will change the input source to SCART

automatically once the AV device is switched on.

Rear View of TV

HDM I1

HDM I3

HDM I2

POW ER

ON/ OFF

AC

SCART Cable

(not included)

Satellite Receiver

VCR

DVD Player / Recorder

Set-top Box

Satellite Receiver

Rear View of TV

HDM I1

HDM I3

HDM I2

POW ER

ON/ OFF

AC

Video Camera

VCR

DVD Player / Recorder

Set-top Box

Game Console

AV Cable

(included)

Yellow (Video)

White (L)

Red (R)

Yellow (Video)

Red (R)

White (L)

GB

16

Connections

Connecting a Coaxial Audio Receiver

For better sound quality, you may want to play the audio through your multi-channel audio receiver.

1. Use an audio cable to connect the TV’s COAXIAL

output socket to an external audio receiver’s

audio coaxial input socket.

2. Plug the connected devices into the mains socket

before switching on the POWER ON/OFF switch

which is located at the rear of the TV next to the

mains cable.

3. Press the

/ I button at the front right side of the

TV or the

button on the remote control to turn on

your TV.

4. Press the SOURCE button at the front right side of

the TV or the INPUT button on the remote control

to display the Source List. Use the

buttons to

select any desired input source and then press the OK

button to confirm.

Connecting Earphones

Connect your earphones to the TV’s socket.

Before putting on earphones, turn the volume down

then put the earphones on and slowly increase the

volume until you reach a comfortable listening level.

Rear View of TV

HDM I1

HDM I3

HDM I2

POW ER

ON/ OFF

AC

Earphones Cable

(not included)

The TV’s volume control will have no

effect. You may control the audio level via

the Audio Receiver.

Listening to loud sounds for prolonged

periods of time may permanently damage

your hearing.

Rear View of TV

HDM I1

HDM I3

HDM I2

POW ER

ON/ OFF

AC

Audio Cable

(not included)

Audio Receiver

GB

17

Connections

Connecting a USB Storage Device

1. Switch off the TV before connecting any USB

storage device.

2. Connect your USB storage device to the USB port

of your TV.

3. Plug the connected devices into the mains socket

before switching on the POWER ON/OFF switch

which is located at the rear of the TV next to the

mains cable.

4. Press the

/ I button at the front right side of the

TV or the

button on the remote control to turn

on your TV.

5. Press the SOURCE button at the front right side of

the TV or the INPUT button on the remote control

to display the Source List. Use the

buttons to

select MEDIA and then press the OK button to

confirm.

Connecting the Aerial

Connect one end of the RF coaxial cable to the aerial

socket on the wall and the other end of the cable to

the RF (75Ω) socket at the rear side of your TV.

OR

HDM I1

HDM I3

HDM I2

POW ER

ON/ OFF

AC

RF coaxial cable

(not included)

Do not connect the TV to the mains

supply until you have completed all the

connections.

• If a hard disk is used, make sure its mains adapter is connected to the mains supply.

• If a USB hub is used, make sure its mains adapter is connected to the mains supply as the total current consumption

may exceed 500mA.

• The maximum supported storage space of the hard disk is 1 TB.

• The file system only supports FAT32 format.

• If you want to store the video streaming of a DTV programme, the transfer rate of the USB storage device must not

be less than 5MB/s, otherwise the picture and sound of the programme will be affected and a warning statement

will be shown on the screen. If this happens, please upgrade your USB storage device.

• The TV screen will be blank temporarily as it will take time to start up and stabilise the connected hard disk. This is

normal and the starting time may vary depending on the brand and the memory size of the connected hard disk.

• Disconnect the USB storage device if it is not in use.

Rear View of TV

HDM I1

HDM I3

HDM I2

POW ER

ON/ OFF

AC

USB Cable

(not included)

Adapter

Portable

hard Disk

USB Hub

USB

18

GB

Initial Setup

6. Channel tuning will commence. This operation may take up to 6

minutes. The display will show the progress of the tuning and the

number of channels found.

7. If you want to skip the ATV tuning, press the MENU button to

interrupt the tuning half way. A pop-up screen will be displayed,

press the

button to select YES to confirm. You will then go

straight to DTV tuning. You may repeat the above step if you also

want to skip the DTV tuning. An installation reminder will appear

the next time you turn on the TV.

8. After tuning is complete, the channels are arranged in the

broadcaster's preset order. If you wish to skip channels, modify

the preset order or rename channels, select Channel Edit under

the Channel menu (refer to page 22-23 for details).

Channel Tuning

TV : 0 Channel

DTV : 0 Channel

Radio : 0 Channel

Data : 0 Channel

1 %... 471.25 MHz (TV)

Please press MENU key to skip

5. Press the buttons to navigate the menu and change the

settings. Press the OK button to confirm.

OSD Language Select your desired language to be displayed on

the menu. The default on-screen menu language

is set as English.

Country Select the country where you will operate the TV.

The default country is set as UK.

Turning the TV on for the First Time

1. Connect the mains cable to the mains socket after you have

completed all the connections.

2. Switch on the POWER ON/OFF switch which is located at

the rear of the TV next to the mains cable. At this stage, the

TV switches to standby mode. The red LED indicator will

illuminate on the front panel of the TV.

3. In standby mode, press the

/ I button at the front right side

of the TV or the

button on the remote control to turn the

TV on. The red LED indicator will turn blue.

4. The first time you turn the TV on, it will go straight into the

First Time Installation menu. Please ensure the aerial is

plugged in and then press the OK button. (If you have already

installed the TV using the Quick Start Guide, please go to the

next step “Selecting the Input Source” on the next page.)

Please ensure aerial is plugged in!!

Then press OK button to start

Please select an OSD Language

Deutsch

Español Français

Português Italiano

English

Country

France

Germany Portugal

Italy Spain

UK

Menu

Always disconnect the TV from the mains socket when

not in use for a long period of time.

The

/ I button at the front right side of the TV or

the

button on the remote control is only used for

switching the TV into standby, it does not disconnect

the TV from the mains power. To completely disconnect

the mains power, please remove the mains plug from

the mains socket or switch off the POWER ON/OFF

switch.

Initial Setup

To the mains socket

19

GB

Initial Setup

Selecting the Input Source

1. Press the SOURCE button at the front right side of the TV or the INPUT

button on the remote control to display the Input source list.

2. Press the

buttons to select the input source that you want: DTV / ATV /

AV / SCART / YPBPR / HDMI1 / HDMI2 / HDMI3 / PC / MEDIA.

3. Press the OK button to confirm your selection. If you do not press the OK

button to confirm, the TV will automatically confirm the selected input

source within 4 seconds.

• Press the CH / buttons on the remote control repeatedly or the 0-9

buttons to select the channel.

Alternative

Press the LIST button to enter the Channel List. Then use the

buttons to highlight and select the channel. Press the OK button to

view the selected channel.

If a blocked channel is selected, the password screen will be displayed.

Press the 0-9 buttons to enter the password, the channel will then be

unlocked (refer to page 22-23 for details on Channel Edit).

• Press the FAV button to view the Favourite List. Then use the

buttons

to highlight and select the channel. Press the OK button to view the selected

channel (refer to page 22-23 for details on Channel Edit).

• Press the

button to return to the previously viewed channel.

Display Channel Information

• Press the button to view the current information.

Volume Adjustment

• Press the VOL + or – button at the front right side of the TV or on the remote control to adjust the volume.

• If you wish to switch the sound off, press the

MUTE button. Press the MUTE button again or the VOL + button to resume

audio listening.

In DTV mode, press the TV.RD button to switch to

TV / digital radio channels directly.

Input Source

DTV

ATV

AV

YPBPR

HDMI2

SCART

HDMI1

PC

HDMI3

MEDIA

20

GB

Using the Features

4. Channel tuning will commence. This operation may take up to 6 minutes.

The display will show the progress of the tuning and the number of

channels found.

5. If you want to skip the ATV tuning, press the MENU button to interrupt

the tuning half way. A pop-up screen will be displayed, press the

button to select YES to confirm. You will then go straight to DTV tuning.

You may repeat the above step if you also want to skip the DTV tuning.

An installation reminder will appear the next time you turn on the TV.

6. After tuning is complete, the channels are arranged in a preset order. If

you wish to skip channels, modify the preset order or rename channels,

select Channel Edit under the channel menu (refer to page 22-23 for

details).

3. In the Tune Type menu, press the

buttons to select ATV / DTV /

DTV + ATV. Press the

button and then press the buttons to

select the country where you will operate the TV. Press the OK button to

confirm.

2. Press the

buttons to select Auto Tuning and then press the OK

button.

Customising the Channel Setting (TV, DTV or Radio Mode)

Auto Tuning (ATV / DTV mode)

Use this to automatically find and store all available channels. This is normally recommended if some channels have been added

or removed by the broadcaster or if you have moved house.

1. Press the MENU button and then press the

buttons to select the

CHANNEL menu and then press the OK button.

Channel Tuning

TV : 0 Channel

DTV : 0 Channel

Radio : 0 Channel

Data : 0 Channel

1 %... 471.25 MHz (TV)

Please press MENU key to skip

CHANNEL

PICTURE

SOUND

TIME

OPTION

LOCK

EXIT

Tune Type

France

Germany

Portugal

Italy

Spain

UK

Menu

ATV+DTV

Other

Using the Features

Auto Tuning

ATV Manual Tuning

Software Update(OAD) Off

Software Update(USB)

Channel Edit

(ATV mode)

Auto Tuning

DTV Manual Tuning

Signal Information

CI Information

Software Update(OAD) Off

Software Update(USB)

Channel Edit

(DTV mode)

Page is loading ...

Logik L40LCD11 User manual

Logik L40LCD11 User manual

Related papers

Other documents