Logik L323CD11 User manual

L323CD11
Logik
Brand
Logik
Model
L323CD11
Category
LCD TVs
Type
User manual

This manual is also suitable for

42" / 47" 3D Ready LCD TV
Instruction Manual
L423CD11
L473CD11
L42_473CD11_IB_111013_Zell.indd 1 13/10/2011 12:05 PM
L42_473CD11_IB_111013_Zell.indd 2 13/10/2011 12:05 PM
Contents
Preparation .........................................................................................................................................................................................5
Unpacking the TV ...............................................................................................................................................................................................................5
Installing / Removing the Base Stand .........................................................................................................................................................................6
Front / Right Side View and Controls ...........................................................................................................................................................................7
Rear View and Sockets ......................................................................................................................................................................................................8
Installing Batteries in the Remote Control ................................................................................................................................................................9
Remote Control Operation Range ................................................................................................................................................................................9
Remote Control .................................................................................................................................................................................................................10
Connections ......................................................................................................................................................................................12
Making Video and Audio Connections .....................................................................................................................................................................12
Connecting an AV Device with an HDMI Cable .....................................................................................................................................................12
Connecting a Computer with a VGA Cable .............................................................................................................................................................13
Connecting an AV Device with a Component (YPbPr) Cable ...........................................................................................................................13
Connecting an AV Device with a SCART Cable ......................................................................................................................................................14
Connecting an AV Device with Composite Cable .................................................................................................................................................14
Connecting a Digital Audio Receiver ........................................................................................................................................................................15
Connecting an Audio Receiver ....................................................................................................................................................................................15
Connecting Headphones ...............................................................................................................................................................................................16
Initial Setup ......................................................................................................................................................................................17
Turning the TV on for the First Time ..........................................................................................................................................................................17
− Target Region Descriptor ...................................................................................................................................................................................18
− Selecting the Input Source................................................................................................................................................................................19
− Channel Selection ...............................................................................................................................................................................................19
− Display Channel Information ...........................................................................................................................................................................19
− Volume Adjustment .............................................................................................................................................................................................19
Customising TV Settings .................................................................................................................................................................20
Channel Setting (TV, DTV or Radio Mode) .............................................................................................................................................................. 20
− Auto Tuning (ATV / DTV mode)....................................................................................................................................................................... 20
− ATV Manual Tuning (ATV mode) .....................................................................................................................................................................21
− DTV Manual Tuning (DTV mode) ....................................................................................................................................................................21
− Channel Edit (ATV Mode) .................................................................................................................................................................................. 22
− Channel Edit (DTV Mode) .................................................................................................................................................................................. 23
− Signal Information (DTV Mode) ...................................................................................................................................................................... 23
− CI (Common Interface) (DTV Mode) .............................................................................................................................................................. 24
− Software Update (USB) ...................................................................................................................................................................................... 25
Picture Setting .................................................................................................................................................................................................................. 26
Sound Setting ................................................................................................................................................................................................................... 27
− Stereo / Dual Sound Reception (ATV Mode) .............................................................................................................................................. 28
− Speaker Sound Output Selection (DTV Mode) ......................................................................................................................................... 29
Time Setting ...................................................................................................................................................................................................................... 29
Option Setting .................................................................................................................................................................................................................. 30
− OSD Language ...................................................................................................................................................................................................... 30
− TT Language ...........................................................................................................................................................................................................31
− Audio Language (DTV Mode) .......................................................................................................................................................................... 32
− Subtitle Language (DTV Mode) ...................................................................................................................................................................... 32
− Hearing Impaired ................................................................................................................................................................................................. 33
− PVR File System (DTV Mode) ............................................................................................................................................................................ 33
− Aspect Ratio ........................................................................................................................................................................................................... 35
− Blue Screen ............................................................................................................................................................................................................ 36
− Restore Factory Default ..................................................................................................................................................................................... 36
Lock Setting ....................................................................................................................................................................................................................... 37
− Lock System ........................................................................................................................................................................................................... 37
− Set Password ......................................................................................................................................................................................................... 37
− Block Channel ....................................................................................................................................................................................................... 38
− Parental Guidance ............................................................................................................................................................................................... 39
− Key Lock ..................................................................................................................................................................................................................40
L42_473CD11_IB_111013_Zell.indd 3 13/10/2011 12:05 PM
Using the Features ...........................................................................................................................................................................41
EPG (Electronic Programme Guide) (DTV Mode) ..................................................................................................................................................41
− Switch On / O EPG ..............................................................................................................................................................................................41
− Select a Programme ............................................................................................................................................................................................41
Teletext (ATV Mode) ........................................................................................................................................................................................................ 42
− To Turn on Teletext Function........................................................................................................................................................................... 42
Digital Teletext (DTV Mode) ......................................................................................................................................................................................... 42
− Teletext within Digital Service ........................................................................................................................................................................ 42
Entertainment ..................................................................................................................................................................................43
3D Imaging ......................................................................................................................................................................................................................... 43
− 3D Technology ...................................................................................................................................................................................................... 43
− 3D Imaging Viewing Range ............................................................................................................................................................................. 44
− Watching 3D TV .................................................................................................................................................................................................... 44
− 3D Options ............................................................................................................................................................................................................. 44
− 3D Customised Setting ...................................................................................................................................................................................... 44
Connecting a USB Storage Device ............................................................................................................................................................................. 45
Viewing Photos ................................................................................................................................................................................................................. 46
Listening to Music ............................................................................................................................................................................................................ 46
Watching Movies .............................................................................................................................................................................................................. 47
Viewing Texts .................................................................................................................................................................................................................... 48
PVR (Personal Video Recorder) .......................................................................................................................................................49
Time Shift Function (DTV Mode) ................................................................................................................................................................................ 49
Recording DTV Programme onto a USB Storage Device .................................................................................................................................. 50
Timer Programming ....................................................................................................................................................................................................... 50
Play Recorded Programme ...........................................................................................................................................................................................51
Maintenance .....................................................................................................................................................................................53
Display Modes ..................................................................................................................................................................................55
YPbPr Mode ....................................................................................................................................................................................................................... 55
PC Mode .............................................................................................................................................................................................................................. 55
HDMI Mode ....................................................................................................................................................................................................................... 55
Specifications ...................................................................................................................................................................................56
Safety Warnings ...............................................................................................................................................................................58
L42_473CD11_IB_111013_Zell.indd 4 13/10/2011 12:05 PM
GB
5
Preparation
Unpacking the TV
Remove all packaging from the TV. Retain the packaging. If you dispose of it please do so according to local regulations.
The following items are included:
Screws x 6
(P.N.: 119020013)
Mains Cable
(P.N.: 117010062)
3D Glasses x 5
(P.N.: 118050098)
Remote Control / AAA Batteries x 2
(P.N.: 118020377 & 118030017)
Instruction Manual
(P.N.: 120010001-L423CD11/L473CD11)
Quick Start Guide
(P.N.: 120010161-L423CD11/L473CD11)
Digital TV Switchcover Addendum
(P.N.: 120010193)
3D
Thank you for purchasing your new Logik 42" / 47" 3D Ready LCD TV.
Your new TV has many features and incorporates the latest technology to enhance your viewing
experience. We recommend that you spend some time reading this instruction manual in order that you
fully understand these features. You will also find some hints and tips to help you resolve any issues.
Read all the safety instructions carefully before use and keep this instruction manual for future reference.
If items are missing, or damaged please contact Partmaster (UK only). Tel: 0844 800 3456 for assistance.
Preparation
TV
Base Stand
(P.N.: 101040383)
L42_473CD11_IB_111013_Zell.indd 5 13/10/2011 12:05 PM
GB
6
Preparation
5. Mounting on the wall. This TV is designed to be wall-
mounted with a standard 600 mm x 400 mm mounting
kit designed for flat-panel TVs (sold separately). Mount
this TV according to the instructions included in the
mounting kit. Due to space restrictions, we recommend
that you make all connections (refer to pages 12-16 and
page 45 for details) before mounting on to the wall.
3. To install the base stand first make sure you position the
front of the base stand at the front of the TV. Slide the
base stand to the TV and then use the 6 screws to fix the
base stand to the TV.
4. To remove the stand assembly, lay the TV down on a flat
surface with the back side facing up. Please make sure
to place a soft cushioned material (such as a pillow or
thick piece of foam) beneath the screen. Untighten the 6
screws that hold the stand assembly to the rear of the TV.
Slide the base stand out.
1. Disconnect all cables connected to the TV.
2. Lay the TV down on a flat surface with the back side
facing up. Please make sure to place a soft cushioned
material (such as a pillow or thick piece of foam) beneath
the screen.
Installing / Removing the Base Stand
• In order to get the best 3D effect from your wall mounted 3D TV, we strongly recommend
that you use a tilting wall mount bracket. This will enable you to angle the TV direct at your
favourite viewing position.
• Please read this instruction manual carefully while setting up your TV.
• If you require additional assistance please call our UK Call Centre on 0844 561 1234. Our UK
Customer Contact Centre is open Monday-Saturday 8am-8pm or Sunday 8am-6pm.
Keep all the spare screws should you want
to use the base stand option.
The screw holes will only align if the front of
the base stand is at the front of the TV.
The LCD display is very fragile, and must be protected at all times when installing and removing the base stand. Be
sure that no hard or sharp object, or anything that could scratch or damage the LCD display, comes into contact with
it. DO NOT exert pressure on the front of the TV at any time because the screen could crack.
Remove the stand assembly before mounting the TV onto the wall.
screw
unscrew
Screws x 6
(P.N.: 119020013)
Screws x 6
(P.N.: 119020013)
600 mm
400 mm
Four mounting holes
(size M5 screw)
L42_473CD11_IB_111013_Zell.indd 6 13/10/2011 12:05 PM
GB
7
Preparation
Front / Right Side View and Controls
Item Description
1 IR (Infrared Receiver)
Receives IR signals from the remote control.
Do not put anything near the sensor, as its function may be affected.
2 POWER LED
Illuminates green when the TV is turned on. Illuminates red when the TV is in standby
mode. The LED will alternate between red and green when the timer programming has
started in the standby mode.
3 TV/AV
Press to select among different input signal sources:
DTV / ATV / AV / SCART / YPBPR / HDMI1 / HDMI2 / HDMI3 / PC / USB.
Confirmed the selection on OSD menu.
4 MENU Displays the OSD (on screen display) menu.
5 CH + / – Press to select a channel or select a sub-menu from the OSD menu.
6 VOL + / –
Adjusts the volume.
Press to select and adjust a setting in the OSD menu.
7 STANDBY
Switches the TV on from standby mode.
Switches the TV back to standby mode.
INPUT MENU CH+ CH- VOL+ VOL- POWR
TV/AV MENU CH+ CH- VOL+ VOL- STANDBY
3
4
7
6
6
1 2
L42_473CD11_IB_111013_Zell.indd 7 13/10/2011 12:05 PM
GB
8
Preparation
Rear View and Sockets
Socket Description
1 AUDIO OUT (L/R)
To connect to a DVD player, Digital Set-Top-Box, or other AV devices with audio input
sockets.
2 USB
Allows the insertion of a USB storage device to play video, audio, photo and text files
(USB mode) and record DTV programmes on to a USB storage device.
3 HDMI1 / 2 / 3
To connect to a High-Definition (HD) signal output device, such as a set-top box, blu-ray
disc player or AV receiver.
4 PC Audio In / VGA To connect to a computer or other devices with a VGA interface.
5 Common Interface Slot Allows the insertion of a Common Access Module. (Refer to page 24 for details)
6 SCART To connect to a VCR, DVD Player, or other AV device with a SCART output socket.
7 Digital Audio Out To connect to the audio socket on the digital/standard 5.1 audio system.
8 VIDEO / AUDIO (L/R)
To connect to the Composite VIDEO and AUDIO (L/R) output sockets on external video
devices.
9 YPbPr / AUDIO (L/R)
To connect to a DVD player, Digital Set-Top-Box, or other AV devices with component
(YPbPr) video and audio output sockets.
10 Aerial To connect to the aerial socket on the wall with the RF coaxial cable.
11
Headphone Out
To connect to the headphones.
12 AC POWER IN Connects the mains cable to the mains socket.
13 POWER SWITCH Switch on the POWER ON/OFF switch to turn the TV to standby mode.
HDMI 1 HDMI 2 HDMI 3 VGA PC audio SCART
Digi tal
Audi o out AV R in L i n Aeri al
AC P OW ER IN POWER SWIT CH
Y Pr Pb
Comm on In terfa ce
USB
Head phone out
L R
Audi o out
1 2 6 7 8 10 11 12 13
5 9
3 4
L42_473CD11_IB_111013_Zell.indd 8 13/10/2011 12:05 PM
GB
9
Preparation
Remote Control Operation Range
Point the remote control at the TV no more than 5 metres from the
remote control sensor on the TV and within 60° in front of the TV.
The operating distance may vary depending on the brightness of the
room.
Installing Batteries in the Remote Control
1. Press and lift the back cover to open the battery compartment of the
remote control.
2. Insert two AAA size batteries. Make sure to match the (+) and ( - ) ends
of the batteries with the (+) and ( - ) ends indicated in the battery
compartment.
3. Close the battery compartment cover.
Handling the Batteries
• Improper or incorrect use of batteries may cause
corrosion or battery leakage, which could cause
fire, personal injury or damage to property.
• Only use the battery type indicated in this manual.
• When the batteries are exhausted, the remote will
not function. Replace both batteries at the same
time with new ones.
• Do not install new batteries with used ones and do
not mix different types of batteries.
• Do not dispose of used batteries as domestic
waste. Dispose of them in accordance with local
regulations.
Handling the Remote Control
• Take care of your fingernails when you press and
hold the battery release tab.
• Do not drop or cause impact to the remote control.
• Do not spill water or any liquid on the remote
control.
• Do not place the remote control on a wet object.
• Do not place the remote control under direct
sunlight or near sources of excessive heat.
• Remove the battery from the remote control
when not in use for a long period of time, as it
could cause corrosion or battery leakage and may
result in physical injury and/or property damage
including fire.
3D
30° 30°
5M
L42_473CD11_IB_111013_Zell.indd 9 13/10/2011 12:05 PM
GB
10
Preparation
1.
Mutes and restores your TV sound.
2.
Switches the TV between on and standby mode.
3. Source
Select among the dierent input signal sources:
DTV / ATV / AV / SCART / YPBPR / HDMI1 / HDMI2 / HDMI3 / PC
/ USB.
4. Menu
Display the OSD (On Screen Display) menu.
5. Help
Display the Help menu.
6. 3D
• Select among the dierent 3D options:
Side by Side / Top Bottom / Frame Packing / Line by Line / 3D
O
• Normal 2D images as a simulated 3D eect (2D to 3D).
7. TV
A short-cut to switch input source to TV / Digital radio channels.
(DTV mode)
8.
Eject a disc. (DVD mode)
9.
• To start the timeshift playback. (DTV mode)
• To start playback or pause. (USB / DVD mode)
10.
To stop the playback or recording. (USB / DVD mode)
11.
Record the current programme. (DTV mode)
12.
To reverse / advance playback rapidly. (DVD / USB mode)
13.
To skip to the beginning of the previous or next chapter / track /
photo. (DVD / USB mode)
14. USB1 / USB2
Display the Recorded List on USB1 / USB2. (DTV mode)
15. A / B
Display the Schedule List on USB1 / USB2. (DTV mode)
16. Coloured buttons
Access the TELETEXT items or channel edit when using Digital /
Freeview TV Channels. (ATV / DTV mode)
17.
Exit
Exit the OSD menu.
18.
Info
• Display the present channel information such as the current
time and channel name. (ATV / DTV mode)
• Display the present disc information. (DVD mode)
Remote Control
Please note that the DVD mode functions on the remote control only operate on TV
models with a built-in DVD player.
3D
1
4
8
12
14
17
16
7
3
5
9
2
6
11
13
15
18
10
L42_473CD11_IB_111013_Zell.indd 10 13/10/2011 12:05 PM
GB
11
Preparation
19.
Allows you to navigate the OSD menus and adjust the
system settings to your preference.
OK
• Conrm the selection in the OSD menus.
• Display channel list. (ATV / DTV mode)
20. P
• Press the P button once and then press the
buttons to select picture mode: Dynamic / Standard /
Mild / Personal.
• Press the P button twice and then press the
buttons to allow you to watch the screen in various
picture formats: Auto / 4:3 / 16:9 / Zoom / Smart Zoom
/ Dot to Dot / Subtitle. (Dot to Dot only operates in
YPBPR / HDMI mode)
21. S
• Press the S button once and then press the
buttons to select sound mode: Standard / Music /
Movie / Sports / Personal.
• Press the S button twice and then press the
buttons to select speaker sound output. (DTV mode)
• Press the S button twice and then press the
buttons to select Mono to Nicam Stereo. (ATV mode)
22. GUIDE
Displays the EPG (Electronic Programme Guide). (DTV
mode)
23. VOL + / –
Adjusts the volume.
24. CH + / –
Select a channel.
25.
Return to the previous viewing channel. (ATV / DTV
mode)
26. 0-9 Number Button
• Press to select a programme. (ATV / DTV mode)
• Select numbered items in a menu. (DVD mode)
27. SUB
• Selects subtitles which are broadcast with the
programme. (DTV mode)
• Selects subtitles on the DVD. (DVD mode)
28. TEXT
Turns on and o the teletext function. (ATV / DTV mode)
Please note that the DVD mode functions on the remote control only operate on TV
models with a built-in DVD player.
3D
20
27
23
26
22
19
21
28
24
25
L42_473CD11_IB_111013_Zell.indd 11 13/10/2011 12:05 PM
GB
12
Connections
Connecting an AV Device with an HDMI Cable
• This TV can accept High-Definition Multimedia Interface (HDMI) and supports HDCP (High-Bandwidth Digital Content
Protection) Protocol.
• The TV has a total of 3 HDMI input sockets, please make sure the correct input source is selected corresponding to your
connected HDMI input socket.
• When you connect to the output of an HD ready player (blu-ray disc player, game console, set-top box or computer) switch to
the HDMI function and the TV will automatically detect the resolution used by the HDMI source.
• To get the best picture quality, adjust the blu-ray disc player, game console or set-top box output resolution up to 1920 x
1080p.
1. Use an HDMI cable to connect the TV’s HDMI1 /
HDMI2 / HDMI3 input socket to the external AV
device’s HDMI output socket.
2. Plug the connected devices into the mains socket
before switching on the POWER SWITCH which is
located at the rear of the TV.
3. Press the STANDBY button at the front right side
of the TV or the
button on the remote control to
turn on your TV.
4. Press the TV/AV button at the front right side of
the TV or the Source button on the remote control
to display the Source List. Use the
buttons to
select HDMI1 or HDMI2 or HDMI3 and then press
the OK button to confirm.
Making Video and Audio Connections
Not all AV devices have the ability to connect to a TV, please refer to the owner’s manual of your AV device for compatibility and
connection procedures.
When connecting any external AV device, do not connect the mains cable to the mains socket until all other connections are
complete.
Signal Type
Separate Audio
Connection Required
HDMI
HDMI
(480i/480p/576i/576p/720p/1080i/1080p)
No
PC
Yes
Component Video
(480i/480p/576i/576p/720p/1080i/1080p)
Yes
SCART (RGB Input) No
Composite Video
Yes
Best Video
Performance
Connections
Although this TV is able to connect to an
HDMI device, it is possible that some devices
may not operate correctly.
Rear View of TV
HDM I1 HDM I2 HDMI3 VGA P C aud io SC ART
Dig ital
Aud io ou t AV R i n L in Aeria l
AC POWER IN POW ER SW ITCH
Y Pr Pb
Com mon I nterf ace
USB
Hea dphon e out
L R
Aud io ou t
Blu-ray Player / DVD Player /
Recorder
Set-top Box
Game Console
HDMI Cable
(not included)
L42_473CD11_IB_111013_Zell.indd 12 13/10/2011 12:05 PM
GB
13
Connections
Connecting an AV Device with a Component (YPbPr) Cable
1. Use a component cable to connect the TV’s YPbPr
input sockets to an external AV device’s component
output sockets.
2. Use an AV cable to connect the TV’s
AUDIO(L/R) input sockets to the external AV
device’s component audio output sockets.
(Audio Left = white, and Audio Right = red)
Component port on the TV Y Pb Pr
Video output ports on
DVD player
Y Pb Pr
Y Cb Cr
3. Plug the connected devices into the mains socket
before switching on the POWER SWITCH which is
located at the rear of the TV.
4. Press the STANDBY button at the front right
side of the TV or the
button on the remote
control to turn on your TV.
5. Press the TV/AV button at the front right side
of the TV or the Source button on the remote
control to display the Source List. Use the
buttons to select YPbPr and then press
the OK button to confirm.
Connecting a Computer with a VGA Cable
1. Use a VGA cable to connect the TV’s PC input
socket to a computer’s VGA output socket. Use an
audio cable to connect the TV’s PC AUDIO input
socket to the computer’s audio output socket.
2. Plug the connected devices into the mains socket
before switching on the POWER SWITCH which is
located at the rear of the TV.
3. Press the STANDBY button at the front right side of
the TV or the
button on the remote control to turn
on your TV.
4. Press the TV/AV button at the front right side of the
TV or the Source button on the remote control to
display the Source List. Use the
buttons to select
PC and then press the OK button to confirm.
• The best resolution is 1440 x 900.
• If your computer is set to shut down after a
few minutes of idle mode, the TV will also
switch to standby due to no signal being
received, this is to save energy. Press the
STANDBY button at the right side of the TV
when viewed from the front or the
button
on the remote control to restart the TV.
Rear View of TV
VGA Cable
(not included)
Audio Cable
(not included)
HDM I1 HDM I2 HD MI3 VGA PC audio SCAR T
Dig ital
Aud io ou t AV R i n L in Aeria l
AC POWER IN POW ER SW ITCH
Y Pr Pb
Com mon I nterf ace
USB
Hea dphon e out
L R
Aud io ou t
Computer
HDM I1 HDM I2 HDM I3 VGA P C aud io S CART
Dig ital
Aud io ou t AV R i n L in Aerial
AC POWER IN POW ER SW ITCH
Y Pr Pb
Com mon I nterf ace
USB
Hea dphon e out
L R
Aud io ou t
Rear View of TV
L
R
COMPONENT
OUT
Y
Pr
Pb
Satellite Receiver
Video Camera
Blu-ray Player / DVD Player /
Recorder
Set-top Box
Game Console
Component Cable
(not included)
Pb/Cb
Pb/Cb
Y
Pr/Cr
Pr/Cr
Y
AV Cable
(not included)
Yellow (Video)
White (L)
Red (R)
Yellow (Video)
Red (R)
White (L)
L42_473CD11_IB_111013_Zell.indd 13 13/10/2011 12:05 PM
GB
14
Connections
Connecting an AV Device with Composite Cable
1. Use an AV cable to connect the TV’s AUDIO(L/R)/
VIDEO input sockets to an external AV device’s
composite audio/video sockets. (Video = yellow,
Audio Left = white, and Audio Right = red)
2. Plug the connected devices into the mains socket
before switching on the POWER SWITCH which is
located at the rear of the TV.
3. Press the STANDBY button at the front right side of
the TV or the
button on the remote control to turn
on your TV.
4. Press the TV/AV button at the front right side of the
TV or the Source button on the remote control to
display the Source List. Use the
buttons to select
AV and then press the OK button to confirm.
Connecting an AV Device with a SCART Cable
1. Use a SCART cable to connect the TV’s SCART input
socket to an external AV device’s SCART output
socket.
2. Plug the connected devices into the mains socket
before switching on the POWER SWITCH which is
located at the rear of the TV.
3. Press the STANDBY button at the front right side of
the TV or the
button on the remote control to turn
on your TV.
4. The TV will change the input source to SCART
automatically once the AV device is switched on.
Rear View of TV
HDM I1 HDM I2 HD MI3 VGA PC audio SCAR T
Dig ital
Aud io ou t AV R i n L in Aeria l
AC POWER IN POW ER SW ITCH
Y Pr Pb
Com mon I nterf ace
USB
Hea dphon e out
L R
Aud io ou t
SCART Cable
(not included)
Satellite Receiver
VCR
DVD Player / Recorder
Set-top Box
Satellite Receiver
Rear View of TV
HDM I1 HDM I2 HD MI3 VGA PC audio SCAR T
Dig ital
Aud io ou t AV R i n L in Aeria l
AC POWER IN POW ER SW ITCH
Y Pr Pb
Com mon I nterf ace
USB
Hea dphon e out
L R
Aud io ou t
Video Camera
VCR
DVD Player / Recorder
Set-top Box
Game Console
AV Cable
(not included)
Yellow (Video)
White (L)
Red (R)
Yellow (Video)
Red (R)
White (L)
L42_473CD11_IB_111013_Zell.indd 14 13/10/2011 12:05 PM
GB
15
Connections
Connecting an Audio Receiver
For better sound quality, you may want to play the audio through your multi-channel audio receiver.
1. Use an audio cable to connect the TV’s
AUDIO(L/R) input sockets to the external audio
device’s audio output sockets. (Audio Left =
white, and Audio Right = red)
2. Plug the connected devices into the mains socket
before switching on the POWER SWITCH which is
located at the rear of the TV.
3. Press the STANDBY button at the front right side of
the TV or the
button on the remote control to turn
on your TV.
4. Press the TV/AV button at the front right side of the
TV or the Source button on the remote control to
display the Source List. Use the
buttons to select
any desired input source and then press the OK
button to confirm.
Connecting a Digital Audio Receiver
For better sound quality, you may want to play the audio through your multi-channel audio receiver.
1. Use an audio cable to connect the TV’s Digital
Audio out socket to an external audio receiver’s
audio coaxial input socket.
2. Plug the connected devices into the mains socket
before switching on the POWER SWITCH which is
located at the rear of the TV.
3. Press the STANDBY button at the front right side of
the TV or the
button on the remote control to turn
on your TV.
4. Press the TV/AV button at the front right side of the
TV or the Source button on the remote control to
display the Source List. Use the
buttons to select
any desired input source and then press the OK
button to confirm.
The TV’s volume control will have no
effect. You may control the audio level via
the Audio Receiver.
Audio Receiver
HDM I1 HDM I2 HD MI3 VGA PC audio SCAR T
Dig ital
Aud io ou t AV R i n L in Aeria l
AC POWER IN POW ER SW ITCH
Y Pr Pb
Com mon I nterf ace
USB
Hea dphon e out
L R
Aud io ou t
Rear View of TV
Audio Receiver
White (L)
Red (R)
Audio Cable
(not included)
Red (R)
White (L)
Rear View of TV
HDM I1 HDM I2 HD MI3 VGA PC audio SCAR T
Dig ital
Aud io ou t AV R i n L in Aeria l
AC POWER IN POW ER SW ITCH
Y Pr Pb
Com mon I nterf ace
USB
Hea dphon e out
L R
Aud io ou t
Audio Cable
(not included)
L42_473CD11_IB_111013_Zell.indd 15 13/10/2011 12:06 PM
GB
16
Connections
Connecting Headphones
Connect your headphones to the TV’s socket.
Before putting on headphones, turn the volume down
then put the headphones on and slowly increase the
volume until you reach a comfortable listening level.
Long-term exposure to loud music may
cause hearing damage. It is best to avoid
extreme volume when using earphones,
especially for extended periods.
Rear View of TV
HDM I1 HDM I2 HD MI3 VGA PC audio SCAR T
Dig ital
Aud io ou t AV R i n L in Aeria l
AC POWER IN POW ER SW ITCH
Y Pr Pb
Com mon I nterf ace
USB
Hea dphon e out
L R
Aud io ou t
Earphones Cable
(not included)
L42_473CD11_IB_111013_Zell.indd 16 13/10/2011 12:06 PM
17
GB
Initial Setup
Do not connect the TV to the mains supply
until you have completed all the connections.
2. Connect the mains cable to the AC Power In located
at the rear of the TV and then connect to the mains
socket after you have completed all the connections.
3. Switch on the POWER SWITCH which is located at
the rear of the TV. At this stage, the TV switches to
standby mode. The red LED indicator will illuminate
on the front panel of the TV.
4. In standby mode, press the STANDBY button on the
TV or the
button on the remote control to turn
the TV on. The LED indicator will change from red to
green.
Turning the TV on for the First Time
1. Connect one end of the RF coaxial cable to the aerial
socket on the wall and the other end of the cable to
the Aerial socket at the rear bottom of your TV.
5. The first time you turn the TV on, it will go straight into the First Time
Installation menu. Please ensure the aerial is plugged in and then press
the OK button. (If you have already installed the TV using the Quick Start
Guide, please go to “Selecting the Input Source” section on the next
page.)
Please press OK button to
begin auto tuning !
• Always disconnect the TV from the mains socket when not in use for a long period of time.
• The STANDBY button at the front right side of the TV or the
button on the remote control is only used for
switching the TV into standby, it does not disconnect the TV from the mains power. To completely disconnect the
mains power, please remove the mains cable from the mains socket.
Initial Setup
The STANDBY button is located on the front
right side of the TV.
OFF
ON
HDMI 1 HDMI2 HDMI3 VGA PC a udio SCAR T
Digi tal
Audi o out AV R in L in Aeria l
AC P OWER IN POW ER SW ITCH
Y Pr Pb
Comm on In terfa ce
USB
Head phone out
L R
Audi o out
OR
HDM I1 HDM I2 HD MI3 V GA PC a udio SC ART
Dig ital
Aud io ou t AV R in L in Aeria l
AC POWER IN POW ER SW ITCH
Y Pr Pb
Com mon I nterf ace
USB
Hea dphon e out
L R
Aud io ou t
RF coaxial cable
(not included)
L42_473CD11_IB_111013_Zell.indd 17 13/10/2011 12:06 PM
18
GB
Initial Setup
7. Channel tuning will commence. This operation may take up to 10
minutes. The display will show the progress of the tuning and the
number of channels found.
8. If you want to skip the ATV tuning, press the Menu button to interrupt
the tuning half way. A pop-up screen will be displayed, press the
button to select YES to confirm. You will then go straight to DTV tuning.
You may repeat the above step if you also want to skip the DTV tuning.
An installation reminder will appear the next time you turn on the TV.
9. After tuning is complete, the channels are arranged in the broadcaster's
preset order. If you wish to skip channels, modify the preset order or
rename channels, select Channel Edit under the Channel menu (refer to
pages 22-23 for details).
Target Region Descriptor
During tuning your TV may have received signals from more than one
transmitter. If this has occurred the Target Region Descriptor screen will be
displayed. This will enable you to select the correct regional transmission for
the local news service that you require.
Press the
buttons to adjust each option's setting and then press the OK
button to confirm.
Country Code This will be shown as GBR for the UK.
Primary Region
This will show the regional country (England, Wales,
Scotland, NI).
Secondary Region
This will allow you to set the region for your local
news service on BBC and ITV (London, Beds and
Cambs etc).
Tertiary Region
You may receive signals from more than one
transmitter within the Secondary Region, (e.g Beds
and Cambs may have Luton or Sandy Heath).
Channel Tuning
TV : 0 Channel
DTV : 0 Channel
Radio : 0 Channel
Data : 0 Channel
1 %... 471.25 MHz (TV)
Please press MENU key to skip
Target Region Setting
Country Code GBR
Primary Region England
Secondary Region
Tertiary Region
London
6. Press the buttons to navigate the menu and change the
settings. Press the OK button to confirm.
OSD Language Select your desired language to be displayed on
the menu. The default on-screen menu language
is set as English.
Country Select the country where you will operate the TV.
The default country is set as UK.
Please select an OSD Language
Deutsch
Español Français
Português Italiano
English
Country
France
Germany Portugal
Italy Spain
UK
Menu
L42_473CD11_IB_111013_Zell.indd 18 13/10/2011 12:06 PM
19
GB
Initial Setup
Selecting the Input Source
1. Press the TV/AV button at the front right side of the TV or the Source button
on the remote control to display the Input source list.
2. Press the
buttons to select the input source that you want: DTV / ATV /
AV / SCART / YPBPR / HDMI1 / HDMI2 / HDMI3 / PC / USB.
3. Press the OK button to confirm your selection. If you do not press the OK
button to confirm, the TV will automatically confirm the selected input
source within 4 seconds.
In DTV mode, press the TV button to switch to TV / digital
radio channels directly.
Input Source
DTV
ATV
AV
YPBPR
HDMI2
SCART
HDMI1
PC
HDMI3
USB
Channel Selection
• Press the CH+ / – buttons at the front right side of the TV or on the remote control repeatedly or the 0-9 buttons on the
remote control to select the channel.
Alternative
Press the OK button to enter the Channel List. Then use the buttons to highlight and select the channel.
Press the OK button to view the selected channel.
• If a blocked channel is selected, the password screen will be displayed. Press the 0-9 buttons to enter the password, the
channel will then be unlocked (refer to page 38 for details on Block Channel).
• Press the
button to return to the previously viewed channel.
Display Channel Information
• Press the Info button to view the current information.
Volume Adjustment
• Press the VOL+ or – button at the front right side of the TV or on the remote control to adjust the volume.
• If you wish to switch the sound off, press the
button. Press the button again or the VOL+ or – button to resume audio
listening.
L42_473CD11_IB_111013_Zell.indd 19 13/10/2011 12:06 PM
20
GB
Customising TV Settings
4. Channel tuning will commence. This operation may take up to 6 minutes.
The display will show the progress of the tuning and the number of
channels found.
5. If you want to skip the ATV tuning, press the Menu button to interrupt
the tuning half way. A pop-up screen will be displayed, press the
button to select YES to confirm. You will then go straight to DTV tuning.
You may repeat the above step if you also want to skip the DTV tuning.
An installation reminder will appear the next time you turn on the TV.
6. After tuning is complete, the channels are arranged in a preset order. If
you wish to skip channels, modify the preset order or rename channels,
select Channel Edit under the channel menu (refer to pages 22-23 for
details).
3. In the Tune Type menu, press the
buttons to select ATV / DTV /
DTV + ATV. Press the
button and then press the buttons to
select the country where you will operate the TV. Press the OK button to
confirm.
2. Press the
buttons to select Auto Tuning and then press the OK
button.
Channel Setting (TV, DTV or Radio Mode)
Auto Tuning (ATV / DTV mode)
Use this to automatically find and store all available channels. This is normally recommended if some channels have been added
or removed by the broadcaster or if you have moved house.
1. Press the Menu button and then press the
buttons to select the
CHANNEL menu and then press the OK button.
Channel Tuning
TV : 0 Channel
DTV : 0 Channel
Radio : 0 Channel
Data : 0 Channel
1 %... 471.25 MHz (TV)
Please press MENU key to skip
CHANNEL
PICTURE
SOUND
TIME
OPTION
LOCK
EXIT
Tune Type
France
Germany
Portugal
Italy
Spain
UK
Menu
ATV+DTV
Other
Customising TV Settings
Auto Tuning
ATV Manual Tuning
Software Update(USB)
Channel Edit
(ATV mode)
Auto Tuning
DTV Manual Tuning
Signal Information
CI Information
Software Update(USB) Off
Channel Edit
(DTV mode)
L42_473CD11_IB_111013_Zell.indd 20 13/10/2011 12:06 PM
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64

Logik L323CD11 User manual

L323CD11
Logik
Brand
Logik
Model
L323CD11
Category
LCD TVs
Type
User manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents