Intermec EASYCODER PD4 Installation guide

Type
Installation guide

This manual is also suitable for

Intermec EasyCoder PD41 is a versatile thermal printer designed for high-volume printing applications. With its fast print speed, high resolution, and flexible media handling capabilities, the PD41 is ideal for printing labels, tags, and receipts in a variety of environments. Some of its key capabilities include:

  • High-resolution printing: The PD41 offers print resolutions of up to 300 dpi, ensuring sharp and legible text and graphics.

  • Fast print speed: With print speeds of up to 6 inches per second, the PD41 can quickly and efficiently handle high-volume printing tasks.

Intermec EasyCoder PD41 is a versatile thermal printer designed for high-volume printing applications. With its fast print speed, high resolution, and flexible media handling capabilities, the PD41 is ideal for printing labels, tags, and receipts in a variety of environments. Some of its key capabilities include:

  • High-resolution printing: The PD41 offers print resolutions of up to 300 dpi, ensuring sharp and legible text and graphics.

  • Fast print speed: With print speeds of up to 6 inches per second, the PD41 can quickly and efficiently handle high-volume printing tasks.

EasyCoder
®
PD4/PD41/PD42
Thermal Printhead (200/300 dpi) Installation Instructions
These instructions tell you how to install a 200 dpi or 300 dpi thermal
printhead in an EasyCoder PD4/PD41/PD42 printer. The kit contains the
following:
200 dpi or 300 dpi thermal printhead
Printhead adapter printed circuit board (PCB)
Required Tools
To install the interface board in your printer, you need these tools:
Screwdriver, slotted
Screwdriver, Phillips (with magnetic tip)
Installing the Thermal Printhead and the Adapter PCB
Before you begin installation, please acknowledge the following important
safety notes:
Make sure the printer has been turned off and
disconnected from the power supply before you
start installation.
Stellen Sie sicher, dass der Drucker abgeschaltet
und von der Stromversorgung abgetrennt wurde,
bevor Sie mit der Installation beginnen.
Take precautions against electrostatic discharge, for
example, by wearing grounded wrist straps.
To install the thermal printhead
1 Turn off the printer and unplug the power cord.
2 Open the side door of the printer.
3 Raise the printhead by pulling out the printhead lever and turning it
counterclockwise a quarter of a turn.
4 Remove any thermal transfer ribbon.
5 Remove the old printhead by pulling it out toward the front of the
printer.
Steps 6-9 describe how to replace the printhead adapter PCB which is
necessary if you are changing to a printhead with different resolution (for
instance, going from 200 dpi to 300 dpi). If this is not the case, go to
Step 11.
Note: If you are using a PD4 printer, you cannot switch to a
printhead with a different resolution other than that which the
printer was designed for.
6 Move the balance boxes to the center position, to facilitate the removal of
the adapter PCB.
7 Use an appropriate tool, for example a slotted screwdriver, to carefully
pry the printhead cable connector loose from the adapter PCB.
8 Remove the two screws that attach the adapter PCB to the printer.
Remove the adapter PCB.
9 Attach the new adapter PCB with the two screws removed in Step 8.
10 Connect the printhead cable to the adapter PCB.
11 Insert the new printhead and connect it to the adapter PCB.
12 Adjust the position of the balance boxes so that they fit the width of your
media.
Worldwide Headquarters
6001 36th Avenue West
Everett, Washington 98203
U.S.A.
tel 425.348.2600
fax 425.355.9551
www.intermec.com
©
2007 Intermec Technologies
Corporation. All rights reserved.
13 Close the side door of the printer.
14 Plug in the power cord and turn the printer on.
EasyCoder PD4/PD41/PD42 Thermal Printhead (200/300dpi) Installation Instructions
*1-960658-02*
P/N 1-960658-02
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Intermec EASYCODER PD4 Installation guide

Type
Installation guide
This manual is also suitable for

Intermec EasyCoder PD41 is a versatile thermal printer designed for high-volume printing applications. With its fast print speed, high resolution, and flexible media handling capabilities, the PD41 is ideal for printing labels, tags, and receipts in a variety of environments. Some of its key capabilities include:

  • High-resolution printing: The PD41 offers print resolutions of up to 300 dpi, ensuring sharp and legible text and graphics.

  • Fast print speed: With print speeds of up to 6 inches per second, the PD41 can quickly and efficiently handle high-volume printing tasks.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages