Part No. DMA1611-5AAA01
Published January 2002
SUPERSTACK
®
3WEBCACHE 1000/3000
RACK MOUNTING GUIDE
Rack-Mounting the Webcache
The Webcache is 1U high and will fit in most standard
19-inch rack mounts.
CAUTION: The rear of the Webcache must be
supported. This is best achieved through the use of a
19-inch 4-posted rack.
CAUTION: Disconnect all cables from the Webcache
before continuing.
You must use the rack-mounting rails and screws
supplied with the Webcache. Damage caused to the
Webcache by using incorrect rails and screws
invalidates your warranty.
A Rack-Mounting Kit is supplied with the Webcache
which contains the items shown in Figure 1. The
rack-mounting rails and rack-mounting brackets are
attached to the Webcache. The adjustable brackets and
screws are contained within the Webcache packaging.
Figure 1
The Rack-Mounting Kit Contents
DMA1611-5AAA01.fm Page 1 Wednesday, January 16, 2002 6:24 PM
2 S
UPER
S
TACK
®
3W
EBCACHE
1000/3000 R
ACK
M
OUNTING
G
UIDE
To rack-mount your Webcache:
1
Place the Webcache the right way up on a hard flat
surface, with the front facing towards you. The
rack-mounting brackets are attached to each side of
the Webcache, as shown in Figure 2.
Figure 2 Rack-Mounting Bracket Attached to the Webcache
2
Slide the rack-mounting rails off the rack-mounting
brackets on both sides of the Webcache.
3
Useanadjustablebrackettosecurearack-mounting
rail to the rear of your rack as shown in Figure 3. To
do this:
a
Slide the adjustable bracket onto the
rack-mounting rail and attach it using two of the
screws provided at a position suitable for your
rack.
b
Adjust the rack-mounting rail to fit the depth of
your rack.
c
Use rack-nuts (not supplied) to attach the
rack-mounting rail and adjustable bracket
assembly to the rear of your rack.
Figure 3 Fitting a Rack-Mounting Rail to the Rear of the Rack
DMA1611-5AAA01.fm Page 2 Wednesday, January 16, 2002 6:24 PM
Rack-Mounting the Webcache 3
4
Attach the rack-mounting rail to the front of the rack.
To d o t his :
a
Insert two screws through aligned openings in the
front plate, rack and rack-mounting rail as shown
in Figure 4.
b
Tighten the screws with a suitable screwdriver.
Figure 4 Fitting a Rack-Mounting Rail to the Front of the Rack
5
Slide the rack-mounting brackets on the sides of the
Webcache into the rack-mounting rails.
6
SecurethefrontoftheWebcachetotherackwiththe
captive thumbscrews, as shown in Figure 5. Screw the
thumbscrews into rack-nuts (not supplied).
Figure 5 Attaching the Webcache to the Rack
7
Ensure that the ventilation holes in the Webcache are
not obstructed.
DMA1611-5AAA01.fm Page 3 Wednesday, January 16, 2002 6:24 PM
4 S
UPER
S
TACK
®
3W
EBCACHE
1000/3000 R
ACK
M
OUNTING
G
UIDE
Copyright © 2002, 3Com Technologies. All rights reserved.
Unless otherwise indicated, 3Com registered trademarks are registered in the United
States and may or may not be registered in other countries.
3Com and SuperStack are registered trademarks of 3Com Corporation. The 3Com logo
is a trademark of 3Com Corporation.
Windows is a registered trademark of Microsoft Corporation. Other brand and product
names may be registered trademarks or trademarks of their respective holders.
DMA1611-5AAA01.fm Page 4 Wednesday, January 16, 2002 6:24 PM
-
1
-
2
-
3
-
4
3com SuperStack 3 WEBCACHE 1000 Mounting Manual
- Type
- Mounting Manual
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
3com 3C16115-US - SuperStack 3 Webcache 1000 User manual
-
HP SUPERSTACK 3 WEBCACHE 3000 Release Notes
-
-
-
-
-
-
-
3com SWITCH 4050 Quick Reference Manual
-