Tripp Lite OmniSmart SmartPro USB User manual

Category
Uninterruptible power supplies (UPSs)
Type
User manual

This manual is also suitable for

Owner’s Manual
1111 W. 35th Street Chicago, IL 60609 USA
Customer Support: (773) 869-1234 • www.tripplite.com
Important Safety Instructions
2
Quick Installation
3
Basic Operation
4
Storage & Service
7
Specifications
8
OmniSmart
& SmartPro
®
USB
120V Input/Output, Line-Interactive UPS Systems
Copyright
©
2003 Tripp Lite. All rights reserved.
OmniSmart
is a trademark of Tripp Lite. SmartPro
®
is a registered trademark of Tripp Lite.
Español
9
Français
17
UL1778
200306109 OmniSmart and SmartPro USB Owner’s Manual.qxd 7/14/2003 4:55 PM Page 1
Important Safety Instructions
2
UPS Location Warnings
Install your UPS indoors, away from excess moisture or heat, dust or direct sunlight.
For best performance, keep the indoor temperature between between 32º F and 104º F
(0º C and 40º C).
Leave adequate space around all sides of the UPS for proper ventilation.
UPS Connection Warnings
Connect your UPS directly to a properly grounded AC power outlet. Do not plug the
UPS into itself; this will damage the UPS.
Do not modify the UPS’s plug, and do not use an adapter that would eliminate the UPS’s
ground connection.
Do not use extension cords to connect the UPS to an AC outlet. Your warranty will be
voided if anything other than Tripp Lite surge suppressors are used to connect your UPS
to an outlet.
If the UPS receives power from a motor-powered AC generator, the generator must
provide clean, filtered, computer-grade output.
Equipment Connection Warnings
Do not use Tripp Lite UPS Systems for life-support appliances in which a malfunction
or failure of a Tripp Lite UPS System could cause failure or significantly alter the
performance of a life-support device.
Do not connect surge suppressors or extension cords to the output of your UPS. This
may damage the UPS and will void the surge suppressor and UPS warranties.
Battery Warnings
Your UPS does not require routine maintenance. Do not open your UPS for any reason.
There are no user-serviceable parts inside.
Battery replacement must be performed by qualified service personnel. Because the
batteries present a risk of electrical shock and burn from high short-circuit current,
observe proper precautions. Unplug and turn off the UPS before performing battery
replacement. Use tools with insulated handles, and replace the existing batteries with the
same number and type of new batteries (Sealed Lead-Acid). Do not open the batteries.
Do not short or bridge the battery terminals with any object.
The UPS batteries are recyclable. Refer to local codes for disposal requirements, or in
the USA only call 1-800-SAV-LEAD or 1-800-8-BATTERY (1-800-8-228-8379) or visit
www.rbrc.com for recycling information. Do not dispose of the batteries in a fire.
Do not attempt to add external batteries.
SAVE THESE INSTRUCTIONS
This manual contains instructions and warnings that should be followed during the
installation, operation and storage of all Tripp Lite UPS Systems. Failure to heed these
warnings will void your warranty.
200306109 OmniSmart and SmartPro USB Owner’s Manual.qxd 7/14/2003 4:55 PM Page 2
3
Quick Installation
Connect your UPS to
an electrical outlet.
Your UPS will run a self-test after it is
plugged in. See Basic Operation to understand
the results of its self-test.
Plug your computer, monitor
and other equipment into
the UPS system.
Your UPS is designed to support only comput-
er equipment. You will overload your UPS if
you connect high power draw equipment such
as household appliances or laser printers to
outlets providing UPS battery backup. Select
models feature special outlets (clearly labeled
on the rear panel) which provide surge-only
(not battery backup) protection designed for
laser printers and other heavy-draw devices.
Select UPS Operating Mode.*
Press the ON/OFF button to toggle your UPS
between the UPS (“ ” LED lit) and the
CHARGE ONLY (“ ” LED flashing)
modes. Choose the operating mode based on
your location:
USA, Canada & Western Europe:
Leave the UPS in the UPS mode at all times.
All other countries:
Put the UPS in the CHARGE ONLY
mode when you ar
e not using connected
equipment.
(WARNING! When set to “CHARGE ONLY,” the UPS
will not provide battery backup during a blackout
or brownout)
Put the UPS in the UPS mode when you
ar
e using connected equipment.
*See Basic Operation section for a complete explanation
of each mode.
3
2
1
NORM DELAY
1
2
3
200306109 OmniSmart and SmartPro USB Owner’s Manual.qxd 7/14/2003 4:56 PM Page 3
4
Use the ON/OFF button to do three things:
Switch your UPS’s Operating Mode: While your UPS is plugged
into a live AC outlet, press the ON/OFF button and hold it until you
hear a beep (about 2 seconds) to toggle between the following operat-
ing modes. Choose your UPS’s operating mode based on the regional
guidelines in Step 3 of the Quick Installation section.
• UPS Mode: ENABLES battery backup. UPS Conditions: The UPS
charges its battery and supplies power at its receptacles when it is
receiving utility line power. If utility power fails, the UPS provides
power from its batteries. The “ ” indicator light is lit. Setting
Advantages: Provides battery backup during blackouts or brownouts.
Basic Operation
These connections are optional. Your UPS will function properly without these connections.
Phone Line/Network Line
Surge Suppression
(Select models only)
Your UPS has either jacks which protect against
surges over a phone or network dataline or jacks
which protect against surges on a phone line
only. See Specifications to determine which
jacks your model has.
Using telephone cords or network data cables as
appropriate, connect your wall jack to the UPS
jack marked “IN.” Connect your equipment to
the UPS jack marked “OUT.” Make sure the
equipment you connect to the UPS’s jacks is
also protected against surges on the AC line.
USB Communications
Use any USB cable to connect the USB port of
your computer to the USB port of your UPS.
Download the PowerAlert UPS monitoring soft-
ware program appropriate for your operating
system from www.tripplite.com and install it on
your computer.
2
1
Quick Installation
optional
NORM DELAY
Buttons
1
NORM DELAY
2
200306109 OmniSmart and SmartPro USB Owner’s Manual.qxd 7/14/2003 4:56 PM Page 4
5
• CHARGE ONLY Mode: DISABLES battery backup. UPS
Conditions: The UPS charges its battery and supplies power at its
receptacles when it is receiving utility line power. The “ ” indica-
tor light is flashing. Setting Advantages: Continues to charge the bat-
tery when power is present while turning OFF the inverter to prevent
battery depletion during power outages when equipment is not in use.
Cold-Start Your UPS: You may “cold start” your UPS and use it as a
stand-alone power source when utility power is not present, providing
that the UPS battery is charged. To “cold start” your UPS, press and
hold the ON/OFF button until you hear a beep (about 2 seconds), then
release it. The “ ” indicator light will illuminate and AC power
inverted from stored battery power will be provided at its receptacles.
Shut Down Your UPS: Press and hold the ON/OFF button when AC
line power is absent (i.e. during a blackout, or when the UPS is
unplugged) to deactivate your UPS.
Use the MUTE/TEST button to do two things:
Silence the UPS On-Battery Alarm: Press and hold this button to
silence the UPS On-Battery alarm, a series of short beeps followed by
a brief pause that is activated when the UPS is providing AC power
from battery. Note: When the battery is nearly depleted, the Low
Battery alarm—a continuous beep that cannot be silenced—will alert
you to immediately shut down connected equipment.
Run a Self-Test: Your UPS performs a self-test whenever it is first
plugged in. To have it run a self-test at another time, leave your con-
nected equipment on. With your UPS plugged in and in the UPS mode,
press and hold this button until you hear a beep (about 2 seconds) then
release it.
Results of a Self-Test: All the LEDs* will be lit and the UPS will emit
several short beeps as it momentarily switches to battery to test its
charge and load capacity. The test will last at most 10 seconds. If the
inverter is overloaded, the “ ” LED (on select models) will stay lit
and the UPS will continue to beep after the test; if this happens, remove
some of the load and run the self-test again. If the batteries seem weak,
the “ ” LED will stay lit and the UPS will continue to beep after the
test; if this happens, let UPS charge its batteries for 12 hours and repeat
the test. If the condition persists, contact Tripp Lite for service. CAUTION:
Do not unplug your UPS to test its batteries. This will remove safe
electrical grounding and may introduce a damaging surge into your
network connections.
* Depending on the condition of the incoming voltage the “VOLTAGE REGULATION”
LED may or may not be lit.
Basic Operation
continued
200306109 OmniSmart and SmartPro USB Owner’s Manual.qxd 7/14/2003 4:56 PM Page 5
All Indicator Light descriptions apply when the UPS is plugged into an AC outlet and turned on.
LINE POWER: This green light will turn ON whenever your UPS is receiving
normal AC line power. It will flash while the UPS is in CHARGE ONLY
mode to indicate that the UPS will not provide battery backup during a black-
out or brownout.
BATTERY POWER: This yellow light will turn ON when your UPS is pro-
viding your equipment with battery power.
BATTERY CHARGE: This red light will turn ON continuously after the UPS
runs a self-test to indicate that the UPS’s battery is weakly charged. If it remains
lit after you have allowed the UPS to charge for twelve hours and have run a
second self-test, contact Tripp Lite for service.
OVERLOAD (Select models only): This red light will turn ON continuously
when the UPS is providing power from battery or after the UPS runs a self-test
to indicate that the UPS’s inverter is overloaded. If it lights up, immediately
remove some of the equipment connected to the UPS and run a self-test. Large
overloads may cause your UPS to shut down.
6
AC Receptacles: “UPS/Surge” receptacles are used to provide your con-
nected equipment with AC line power during normal operation and battery
power during blackouts and brownouts. They also protect your equipment
against damaging surges and line noise. “Surge-only” receptacles (identi-
fied on the back of select UPS models) are used to provide peripherals
with surge protection without committing precious battery power to sup-
port them during blackouts.
Telephone/Network Protection Jacks (Select models only): These jacks
protect your equipment against surges over a telephone or data line. Your
UPS has either jacks which can be used with both phone and data lines, or
jacks which can be used with phone lines only. See Specifications to deter-
mine what kind of jacks your UPS has. Connecting your equipment to
these jacks is optional. Your UPS will work properly without this connection.
Basic Operation
continued
Other UPS Features
Indicator Lights
VOLTAGE REGULATION (Select models only): This light will turn
ON when your UPS is automatically correcting high or low utility line
voltage. The UPS will also click gently when this automatic voltage regu-
lation is operating. These are both normal functions of your UPS, and no
action is required on your part.
200306109 OmniSmart and SmartPro USB Owner’s Manual.qxd 7/14/2003 4:57 PM Page 6
7
Storage
All connected equipment should be turned off, then disconnected from the UPS to avoid bat-
tery drain. Unplug your UPS from its AC receptacle, then press and hold its ON/OFF button to
deactivate it. Your UPS is now ready for storage. If you plan on storing your UPS for an extend-
ed period of time, fully recharge the UPS batteries once every three months by plugging the
UPS into a live AC outlet and letting the UPS charge for 4 to 6 hours. If you leave your UPS bat-
teries discharged for an extended period of time, they will suffer a permanent loss of capacity.
Service
If returning your UPS for service, contact your local Tripp Lite dealer or distributor. They will
refer you to a service center. Please carefully pack the UPS using the ORIGINAL PACKING
MATERIAL that came with the unit. Enclose a letter describing the symptoms of the problem.
If the UPS is within the warranty period, enclose a copy of your sales receipt.
Storage & Service
USB Port: The USB port connects your UPS to any USB workstation
or server. Using this port, your UPS can communicate line-fail and
low-battery status to your computer. Use with Tripp Lite software and
any USB cable to automatically save open files and shut down equip-
ment during a blackout. Contact Tripp Lite Customer Support or con-
sult your power protection software manual for more information.
Battery Replacement Door: Under normal conditions, the original bat-
tery in your UPS will last several years. Battery replacement should be
performed only by qualified service personnel. Refer to “Battery
Warnings” in the Safety section on page 2.
Power Sensitivity/Lowline Adjustment: This dial is normally set fully
counterclockwise, which enables the UPS to protect against waveform
distortions in its AC input. When such distortion occurs, the UPS will
normally switch to providing PWM sinewave power from its battery
reserves for as long as the distortion is present. In some areas with poor
utility power or where the UPS’s input power comes from a backup
generator, frequent brownouts and/or chronic waveform distortion could
cause the UPS to switch to battery too often, draining its battery reserves.
You may be able to reduce how often your UPS switches to battery due
to waveform distortion or brownouts by experimenting with different settings
for this dial. As the dial is turned clockwise, the UPS becomes more
tolerant of variations in its input power’s AC waveform and reduces
the voltage point at which it switches to battery. NOTE: The further the
dial is adjusted clockwise, the greater the degree of waveform distortion
and the lower the input voltage the UPS will allow to pass to connect-
ed equipment. When experimenting with different settings for this
dial, operate connected equipment in a safe test mode so that the effect
on the equipment of any waveform distortions in the UPS’s output can be
evaluated without disrupting critical operations. The experiment should last
long enough to assure that all expected line conditions are encountered.
Automatic Voltage Regulation: During brownouts, your UPS will auto-
matically correct low AC line voltage. When automatic voltage regulation is
operating, your UPS may be heard to click gently. This is a normal, auto-
matic operation of your UPS, and no action is required on your part.
Basic Operation
continued
200306109 OmniSmart and SmartPro USB Owner’s Manual.qxd 7/14/2003 4:57 PM Page 7
8
Specifications
Tripp Lite has a policy of continuous improvement. Specifications are subject to change without notice.
SmartPro
®
USB UPS Systems
Model: SMART500USB SMART550USB SMART700USB
Series: 163620U1 AGSM500USBKJR6 AGOM1000USBKSR6
Input Voltage/Frequency: 120V/60 Hz 120V/60 Hz 120V/60 Hz
On-Line Input Voltage Range: 83 - 147 volts 83 - 147 volts 83 - 147 volts
Output Capacity (VA/Watts): 500/300 550/300 700/450
Battery Runtime (Half Load/Full Load) Minutes: 17/5 17/5 20/6
Battery Recharge Time: 2-4 hrs. 2-4 hrs. 2-4 hrs.
Approvals: UL, cUL, NOM, FCC-B UL, cUL, NOM, FCC-B UL, cUL, NOM, FCC-B
Tel/Fax/Data Protection: 1-line tel/DSL 1-line tel/DSL 1-line tel/DSL/Ethernet
OmniSmart
UPS Systems
Model: OMNISMART500 OMNISMART700 OMNISMART850 OMNISMART1000VS
Series: AGSM500USBKJR6 AGOM700USBKSR61 AGOM1050PJR61 AGOM1000USBKSR6
Input Voltage/Frequency: 120V/60 Hz 120V/60 Hz 120V/60 Hz 120V/60 Hz
On-Line Input Voltage Range: 75 - 147 volts 75 - 147 volts 75 - 147 volts 83 - 147 volts
Output Capacity (VA/Watts): 500/300 700/425 850/600 1000/500
Battery Runtime (Half Load/Full Load) Minutes: 17/5 22/7 26/9 17/5
Battery Recharge Time: 2-4 hrs. 2-4 hrs. 2-4 hrs. 2-4 hrs.
Approvals: UL, cUL, NOM, FCC-B UL, cUL, NOM, FCC-B UL, cUL, NOM, FCC-B UL, cUL, NOM, FCC-B
Tel/Fax/Data Protection: 1-line tel/DSL 1-line tel/DSL/Ethernet None 1-line tel/DSL
Model: OMNISMART1050 OMNISMART1400
Series: AGOM1050PJR61 AGOM1400PSR61
Input Voltage/Frequency: 120V/60 Hz 120V/60 Hz
On-Line Input Voltage Range: 75 - 147 volts 75 - 147 volts
Output Capacity (VA/Watts): 1050/705 1400/940
Battery Runtime (Half Load/Full Load) Minutes: 23/7 24/8
Battery Recharge Time: 2-4 hrs. 2-4 hrs.
Approvals: UL, cUL, NOM, FCC-B UL, cUL, NOM, FCC-B
Tel/Fax/Data Protection: None None
ALL UNITS: Output Waveform Line Mode (filtered sinewave); Output Waveform Battery Mode (PWM sine wave); AC Surge Suppression (exceeds IEEE 587 Cat. A & B standards); AC Noise
Attenuation (>40 dB at 1MHz); AC Protection Modes (H to N, H to G, N to G).
FCC RADIO/TV INTERFERENCE NOTICE: Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy,
and if not installed and used in accordance with the instruction manual, may cause interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the device off and on, the user is encouraged to
try to correct the interference using one or more of the following measures: reorient or relocate the receiving antenna; increase the separation between the equipment and receiver; connect
the equipment into an outlet on a circuit different from that which the receiver is connected; consult the dealer or an experienced radio/television technician for help. The user must use shielded
cables and connectors with this product. Any changes or modifications to this product not expressly approved by the party responsible for compliance could void the user's authority to operate
the equipment.
CONSUMER INFORMATION AND FCC REQUIREMENTS (U.S. only):
1. This equipment complies with Part 68 of the FCC rules. On the top or bottom of this equipment is a label that contains, among other information, the FCC registration number for this equipment.
If requested, provide this information to your telephone company.
2. If your Fax/Modem Protector causes harm to the telephone network, the telephone company may temporarily discontinue your service. If possible, they will notify you in advance. But if
advance notice isn't practical, you will be notified as soon as possible. You will be advised of your right to file a complaint with the FCC.
3. Your telephone company may make changes in its facilities, equipment, operations or procedures that could affect the operation of your equipment. If they do, you will be given advance
notice so as to give you an opportunity to maintain uninterrupted service.
4. If you experience trouble with this Fax/Modem Protector, please contact Tripp Lite Customer Support, 1111 W. 35th Street, Chicago, Illinois 60609; Phone (773) 869-1234 for repair/warranty
information. The telephone company may ask you to disconnect this equipment from the network until the problem has been corrected or you are sure that the equipment is not malfunctioning.
5. This equipment may not be used on coin service provided by the telephone company. Connection to party lines is subject to state tariffs. (Contact your state public utility commission or
corporation for information.)
EQUIPMENT ATTACHMENT LIMITATIONS (Models with the Industry Canada label in Canada only): NOTICE: The Industry Canada label identifies certified equipment. This certification
means that the equipment meets the telecommunications network protective, operational and safety requirements as prescribed in the appropriate Terminal Equipment Technical
Requirements Document(s). The Department does not guarantee the equipment will operate to the user’s satisfaction.
Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the local telecommunications company. The equipment must also be installed
using an acceptable method of connection. The customer should be aware that the compliance with the above conditions might not prevent degradation of service in some situations.
Repairs to certified equipment should be coordinated by a representative designated by the supplier. Any repairs or alterations made by the user to this equipment, or equipment malfunctions,
may give the telecommunications company cause to request the user to disconnect the equipment.
Users should ensure for their own protection that the electrical ground connections of the power utility, telephone lines and internal metallic water pipe system, if present, are connected together.
This precaution may be particularly important in rural areas. Caution: Users should not attempt to make connections themselves, but should contact the appropriate electric inspection authority,
or electrician, as appropriate.
Note on Labeling
Two symbols are used on the label.
V~ : AC Voltage
V : DC Voltage
200306109 OmniSmart and SmartPro USB Owner’s Manual.qxd 7/14/2003 4:57 PM Page 8
Manual de operación
1111 W. 35th Street Chicago, IL 60609 EE.UU.
Asistencia al cliente: +1 (773) 869-1234 • www.tripplite.com
Importantes instrucciones de seguridad
10
Instalación rápida
11
Operación básica
12
Almacenamiento y servicio
16
Ficha técnica
16
OmniSmart
y SmartPro
®
USB
Entrada / salida de 120V, sistemas UPS interactivos en línea
© 2003 Tripp Lite. Todos los derechos reservados. OmniSmart y SmartPro
®
son marcas registradas de Tripp Lite.
English
1
Français
17
UL1778
200306109 OmniSmart and SmartPro USB Owner’s Manual.qxd 7/14/2003 4:57 PM Page 9
1 / 1

Tripp Lite OmniSmart SmartPro USB User manual

Category
Uninterruptible power supplies (UPSs)
Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Ask the document