Tripp Lite AGSM1500XPSR3 User manual

Brand: Tripp Lite

Model: AGSM1500XPSR3

Category: Uninterruptible power supplies (UPSs)

Type: User manual

This manual is also suitable for

Owner’s Manual

1111 W. 35th Street Chicago, IL 60609 USA

Customer Support: (773) 869-1234 • www.tripplite.com

Important Safety Instructions

Quick Installation

Basic Operation

Storage & Service

Specifications

SmartPro

120V Input/Output, Line-Interactive UPS Systems

is a registered trademark of Tripp Lite.

Español

Français

UL 1778

200310044 SmartPro XL Owner’s Manual 93-2078.qxd 10/9/2003 4:20 PM Page 1

UPS Location Warnings

• Install your UPS indoors, away from excess moisture or heat, conductive contaminants,

dust or direct sunlight.

• For best performance, keep the indoor temperature between between 32º F and 104º F

(0º C and 40º C).

• Leave adequate space around all sides of the UPS for proper ventilation.

UPS Connection Warnings

• Connect your UPS directly to a properly grounded AC power outlet. Do not plug the

UPS into itself; this will damage the UPS.

• Do not modify the UPS's plug, and do not use an adapter that would eliminate the UPS’s

ground connection.

• Do not use extension cords to connect the UPS to an AC outlet. Your warranty will be

voided if anything other than Tripp Lite surge suppressors are used to connect your UPS to

an outlet.

• If the UPS receives power from a motor-powered AC generator, the generator must

provide clean, filtered, computer-grade output.

Equipment Connection Warnings

• Do not use Tripp Lite UPS Systems for life support appliances in which a malfunction

or failure of a Tripp Lite UPS System could cause failure or significantly alter the

performance of a life-support device.

• Do not connect surge suppressors or extension cords to the output of your UPS. This

might damage the UPS and will void the surge suppressor and UPS warranties.

Battery Warnings

• Your UPS does not require routine maintenance. Do not open your UPS for any reason

except battery replacement. There are no user-serviceable parts inside.

• Battery replacement must be performed by qualified service personnel. Because the

batteries present a risk of electrical shock and burn from high short-circuit current,

observe proper precautions. Unplug and turn off the UPS before performing battery

replacement. Use tools with insulated handles, and replace the existing batteries with the

same number and type of new batteries (Sealed Lead-Acid). Do not open the batteries.

Do not short or bridge the battery terminals with any object.

• The UPS batteries are recyclable. Refer to local codes for disposal requirements, or in

the USA only call 1-800-SAV-LEAD for recycling information. Do not dispose of the

batteries in a fire.

• Only connect Tripp Lite battery packs of the appropriate type and correct voltage to the

external battery connector.

• Do not connect or disconnect external batteries while the UPS is operating from battery.

• Do not attempt to connect external batteries to models without an external battery connector.

Important Safety Instructions

Quick Installation

Connect your UPS to

an electrical outlet.

Your UPS will run a self-test after it is

plugged in. See Basic Operation to understand

the results of its self-test.

Plug your computer, monitor

and external modem into

UPS/Surge outlets. Plug

other equipment into

Surge-only outlet(s).

Separate UPS/Surge and Surge-only outlet(s)

are identified on the back of your UPS. Your

UPS is designed to support only computer

equipment. You will overload your UPS if

you connect high power draw equipment such

as household appliances, laser printers or

surge suppressors to its UPS/Surge outlets.

Select UPS Operating Mode.*

Press the ON/OFF button to toggle your UPS

between the UPS (“ ” LED lit) and the

CHARGE ONLY (“ ” LED flashing)

modes. Choose the operating mode based on

your location:

USA, Canada & Western Europe:

• Leave the UPS in the UPS mode at all times.

All Other Countries:

• Put the UPS in the CHARGE ONLY

mode when you are not

using connected

equipment.

(WARNING! When set to “CHARGE ONLY,” the UPS

will not provide battery backup during a blackout or

brownout)

• Put the UPS in the UPS mode when you

are

using connected equipment.

*See Basic Operation section for a complete explanation

of each mode.

SEE MANUAL FOR

PROPER CONNECTION

NORM DELAY

EXTERNAL

BATTERY

SAVE THESE INSTRUCTIONS

This manual contains instructions and warnings that should be followed during the

installation, operation and storage of all Tripp Lite UPS Systems. Failure to heed these

warnings will void your warranty.

200310044 SmartPro XL Owner’s Manual 93-2078.qxd 10/9/2003 4:20 PM Page 2

Use the ON/OFF button to do three things:

Switch your UPS’s Operating Mode: While your UPS is plugged

into a live AC outlet, press the ON/OFF button and hold it until you

hear a beep (about 2 seconds) to toggle between the following operating

modes. Choose your UPS’s operating mode based on the regional

guidelines in Step 3 of the Quick Installation section.

• UPS Mode: ENABLES battery backup. UPS Conditions: The UPS

charges its battery and supplies power at its receptacles when it is

receiving utility line power. If utility power fails, the UPS provides

power from its batteries. The “ ” indicator light is lit. Setting

Advantages: Provides battery backup during blackouts or brownouts.

• CHARGE ONLY Mode: DISABLES battery backup. UPS

Conditions: The UPS charges its battery and supplies power at its

receptacles when it is receiving utility line power. The “ ” indicator

light is flashing. Setting Advantages: Continues to charge the battery

when power is present while turning OFF the inverter to prevent battery

depletion during power outages when equipment is not in use.

Cold-Start Your UPS: You may “cold start” your UPS and use it as a

stand-alone power source when utility power is not present, providing

that the UPS battery is charged. To “cold start” your UPS, press and

hold the ON/OFF button until you hear a beep (about 2 seconds), then

release it. The “ ” indicator light will illuminate and AC power

inverted from stored battery power will be provided at its receptacles.

Shut Down Your UPS: Press and hold the ON/OFF button when AC

line power is absent (i.e. during a blackout, or when the UPS is

unplugged) to deactivate your UPS.

Use the MUTE/TEST button to do two things:

Silence the UPS On-Battery Alarm: Press and hold this button to

silence the UPS On-Battery alarm, a series of short beeps followed by

a brief pause that is activated when the UPS is providing AC power

from battery. Note: When the battery is nearly depleted, the Low

Battery alarm—a continuous beep that cannot be silenced—will alert

you to immediately shut down connected equipment.

Run a Self-Test: Your UPS performs a self-test whenever it is first

plugged in. To have it run a self-test at another time, leave your

connected equipment on. With your UPS plugged in and in the UPS

mode, press and hold this button until you hear a beep (about 2 sec-

onds) then release it.

Results of a Self-Test: All the LEDs will be lit and the UPS will emit

several short beeps as it momentarily switches to battery to test its

charge and load capacity. The test will last at most 10 seconds. If the

inverter is overloaded, the “ ” LED will stay lit and the UPS will

continue to beep after the test; if this happens, remove some of the load

Basic Operation

These connections are optional. Your UPS will function properly without these connections.

USB Communications

Use any USB cable to connect the USB port of

your computer to the USB port of your UPS.

Download the PowerAlert UPS monitoring soft-

ware program appropriate for your operating

system from www.tripplite.com and install it on

your computer.

Serial Communications

(Select Models Only)

Use the serial cable provided with your UPS to

connect the DB9 port of your computer to the

DB9 port of your UPS. Download the

PowerAlert UPS monitoring software program

appropriate for your operating system from

www.tripplite.com and install it on your computer.

External Battery Connection

(Select Models Only)

External batteries are only needed to extend runtime.

Adding external batteries will increase recharge

time as well as runtime.

The illustration shows the location of your UPS’s

External Battery Connector, where you will

insert the battery pack cable. Complete installation

and mounting instructions for your battery pack

appear in the battery pack’s owner’s manual.

Make sure that cables are fully inserted into their

connectors. Small sparks may result during battery

connection; this is normal.

If you connect more than one external battery,

set the Charge Level switch to EXTERNAL

BATTERY. Your UPS’s charger will increase

its output to handle the additional batteries.

Quick Installation

optional

SEE MANUAL FOR

PROPER CONNECTION

NORM DELAY

EXTERNAL

BATTERY

Buttons

SEE MANUAL FOR

PROPER CONNECTION

NORM DELAY

EXTERNAL

BATTERY

SEE MANUAL FOR

PROPER CONNECTION

NORM DELAY

EXTERNAL

BATTERY

200310044 SmartPro XL Owner’s Manual 93-2078.qxd 10/9/2003 4:20 PM Page 4

and run the self-test again. If the batteries seem weak, the “ ” LED

will stay lit and the UPS will continue to beep after the test; if this

happens, let UPS charge its batteries for 12 hours and repeat the test. If

the condition persists, contact Tripp Lite for service. CAUTION: Do

not unplug your UPS to test its batteries. This will remove safe

electrical grounding and may introduce a damaging surge into your

network connections.

All Indicator Light descriptions apply when the UPS is plugged into an AC outlet and turned on.

LINE POWER: This green light will turn ON whenever your UPS is

receiving normal AC line power. It will flash while the UPS is in

CHARGE ONLY mode to indicate that the UPS will not provide battery

backup during a blackout or brownout.

BATTERY POWER: This light indicates battery charge level:

Green means the batteries are fully charged or nearly so, yellow

means the batteries are partially charged, and red means the batteries

are nearly depleted.

VOLTAGE REGULATION: This light will turn ON when your

UPS is automatically correcting high or low utility line voltage. The

UPS will also click gently when this automatic voltage regulation is

operating. These are both normal functions of your UPS, and no

action is required on your part.

BATTERY CHARGE: This red light will turn ON continuously

after the UPS runs a self-test to indicate that the UPS’s battery is weakly

charged. If it remains lit after you have allowed the UPS to charge for

twelve hours and have run a second self-test, contact Tripp Lite for

service.

OVERLOAD: This light shows how heavy is the load on the UPS’s

inverter. Green indicates a light load, yellow indicates a medium load,

and red indicates a heavy load (above 85% of the UPS’s output capacity).

If this light is flashing, the UPS is overloaded and will not be able to

provide power to connected equipment during a power outage.

Unplug equipment from the UPS until this LED stops flashing.

6 7

Basic Operation

continued

Other UPS Features

USB Port: The USB port connects your UPS to any USB workstation

or server. Using this port, your UPS can communicate line-fail and

low-battery status to your computer. Use with Tripp Lite software and

any USB cable to automatically save open files and shut down equipment

during a blackout. See PowerAlert manual.

DB9 Port (Select Models Only): The DB9 port connects your UPS

to any workstation or server. Use with Tripp Lite’s PowerAlert UPS

monitoring software and a DB9 cable to enable your computer to

automatically save open files and shut down equipment during a

blackout. The UPS can also report power availability and UPS status,

and select UPS models have other capabilities. See PowerAlert manual.

Battery Replacement Door: Under normal conditions, the original

battery in your UPS will last several years. Battery replacement

should be performed only by qualified service personnel. Refer to

“Battery Warnings” in the Safety section on page 2.

External Battery Connector (Select Models Only): Use to connect

battery pack(s) for additional runtime. Refer to Specifications and/or

the label next to the connector to determine the appropriate variety of

battery pack to use. Refer to the battery pack instruction manual for

complete installation information and important safety warnings.

Input Breaker: Prevents high input current from damaging the UPS or the

attached load. If this breaker trips, make sure your UPS is connected

to nominal 120V AC power before resetting the circuit breaker by

pushing the breaker switch in to reset.

Charge Level Switch: This switch should be set to the left unless

you have connected multiple external batteries, in which case you

may set it to EXTERNAL BATTERY, increasing your charger’s output

so the additional batteries recharge faster.

Power Sensitivity Adjustment: This dial is normally set fully counter-

clockwise, which enables the UPS to protect against waveform

distortions in its AC input. When such distortion occurs, the UPS will

normally switch to providing PWM sine wave power from its battery

reserves for as long as the distortion is present. In areas with poor utility

power or where the UPS’s input power comes from a backup generator,

chronic waveform distortion could cause the UPS to switch to battery too

frequently, draining its battery reserves. You may be able to reduce how often

your UPS switches to battery due to waveform distortion by experimenting

with different settings for this dial. As the dial is turned clockwise,

the UPS becomes more tolerant of variations in its input power’s AC

waveform. NOTE: The further the dial is adjusted clockwise, the

greater the degree of waveform distortion the UPS will allow to pass to

connected equipment. When experimenting with different settings for

this dial, operate connected equipment in a safe test mode so that the

effect on the equipment of any waveform distortions in the UPS’s

output can be evaluated without disrupting critical operations.

Basic Operation

continued

NORM DELAY

Indicator Lights

AC Receptacles: These output receptacles provide your connected

equipment with AC line power during normal operation and battery

power during power outages. The UPS protects equipment connect-

ed to these receptacles against damaging surges and line noise. If you

have a USB or DB9 connection to your UPS, you can remotely

reboot connected equipment by turning its receptacles OFF and ON

using Tripp Lite software. Select models have a receptacle that may

be remotely switched ON and OFF without interrupting power to

200310044 SmartPro XL Owner’s Manual 93-2078.qxd 10/9/2003 4:20 PM Page 6

Manual de operación

1111 W. 35th Street Chicago, IL 60609 EE. UU.

Atención al cliente: +1 (773) 869-1234 • www.tripplite.com

Importantes instrucciones de seguridad

Instalación rápida

Operación básica

Almacenamiento y servicio

Ficha técnica

SmartPro

Sistemas UPS de 120V de entrada/salida, interactivos,

con tiempo de respaldo extendido

English

Français

Specifications

Tripp Lite has a policy of continuous improvement. Specifications are subject to change without notice.

Model: SMART700 SMART750XL SMART1050

Series: AGSM1050PJR3 AGSM1500XPSR3 AGSM1050PJR3

Input Voltage/Frequency: 120V/60 Hz 120V/60 Hz 120V/60 Hz

Output Capacity (VA/Watts): 700/600 750/600 1050/800

Battery Runtime

(Half Load/Full Load) Minutes: 20/6 42/18* 23/8

Battery Recharge Time: 2-4 hrs. 2-4 hrs.* 2-4 hrs.

Approvals: UL, cUL, NOM, FCC B UL, cUL, NOM, FCC A UL, cUL, NOM, FCC B

Model: SMART1050XL SMART1500 SMART1500XL

Series: AGSM1500XPSR3 AGSM1500XPSR3 AGSM1500XPSR3

Input Voltage/Frequency: 120V/60 Hz 120V/60 Hz 120V/60 Hz

Output Capacity (VA/Watts): 1050/800 1500/980 1500/980

Battery Runtime

(Half Load/Full Load) Minutes: 26/6* 20/7 20/7*

Battery Recharge Time: 2-4 hrs.* 2-4 hrs. 2-4 hrs.*

Approvals: UL, cUL, NOM, FCC A UL, cUL, NOM, FCC A UL, cUL, NOM, FCC A

*External battery packs can be connected to these models. External battery packs will increase both the battery runtime and

the battery recharge time.

ALL UNITS:

Output Waveform Line Mode (filtered sinewave); Output Waveform Battery Mode (PWM sine wave); AC Surge Suppression (exceeds

IEEE 587 Cat. A & B standards); AC Noise Attenuation (>40 dB at 1MHz); AC Protection Modes (H to N, H to G, N to G); Tripp Lite

External Battery Model (BP36V27).

FCC CLASS A RADIO/TV INTERFERENCE NOTICE:

Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the

FCC Rules. These limits are designed to provide reasonable protection against harmful interference when operated in a com-

mercial environment. This equipment generates, uses and can radiate radio frequency energy, and if not installed and used in

accordance with the instruction manual, may cause interference to radio communications. Operation of this equipment is likely to

cause harmful interference in which case the user will be required to correct the interference at his own expense. The user must

use shielded cables and connectors with this product. Any changes or modifications to this product not expressly approved by the

party responsible for compliance could void the user's authority to operate the equipment.

FCC CLASS B RADIO/TV INTERFERENCE NOTICE:

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the

FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy, and if not installed and used in accordance with the

instruction manual, may cause interference to radio communications. However, there is no guarantee that interference will not

occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is encouraged to try to correct the interference using one or more of the

following measures: reorient or relocate the receiving antenna; increase the separation between the equipment and the receiver;

connect the equipment into an outlet on a circuit different from that which the receiver is connected; consult the dealer or an expe-

rienced radio/television technician for help. The user must use shielded cables and connectors with this product. Any changes or

modifications to this product not expressly approved by the party responsible for compliance could void the user’s authority to

operate the equipment.

Storage

All connected equipment should be turned off, then disconnected from the UPS to avoid battery

drain. Unplug your UPS from its AC receptacle, then press and hold its ON/OFF button to deactivate

it. Your UPS is now ready for storage. If you plan on storing your UPS for an extended period

of time, fully recharge the UPS batteries once every three months by plugging the UPS into

a live AC outlet and letting the UPS charge for 4 to 6 hours. If you leave your UPS batteries

discharged for an extended period of time, they will suffer a permanent loss of capacity.

Service

If returning your UPS for service, contact your local Tripp Lite dealer or distributor. They will

refer you to a service center. Please carefully pack the UPS using the ORIGINAL PACKING

MATERIAL that came with the unit. Enclose a letter describing the symptoms of the problem.

If the UPS is within the warranty period, enclose a copy of your sales receipt.

Storage & Service

UL 1778

200310044 SmartPro XL Owner’s Manual 93-2078.qxd 10/9/2003 4:20 PM Page 8

1111 W. 35th Street, Chicago, IL 60609 USA

773.869.1234 (USA) • 773.869.1212 (International)

www.tripplite.com

200310044 93-2078_ES

Tripp Lite AGSM1500XPSR3 User manual

Brand: Tripp Lite

Model: AGSM1500XPSR3

Category: Uninterruptible power supplies (UPSs)

Type: User manual

This manual is also suitable for

Download PDF

report

Tripp Lite AGSM1500XPSR3 User manual

This manual is also suitable for

Tripp Lite AGSM1500XPSR3 User manual

Related papers

Other documents