Craftsman 490-900-S068 Operating instructions

Type
Operating instructions
*
Smart Lawn Connect Kit
Installation Instructions
Installation Guide:
1 Using socket wrench, remove (2) bolts between fender and seat with 5/16” socket - extender required,
and (1) Torx screw in front with T30 driver from drivers right Fender (see illustration below).
These instructions apply to Craftsman Zero Turn riding mowers (model #247.XXXXX) Please read
through entire instruction sequence before beginning installation.
Congratulations on purchasing a Craftsman Smart Lawn Connect Kit. The Craftsman Smart Lawn Connect Plug
will easily plug in to the back side of your Craftsman Rider’s Ignition Switch located on the dashboard.
October 26, 2016
WARNING Before performing any maintenance or repairs and to reduce the risk of injury,
disengage PTO, set parking brake, stop engine and remove key to prevent unintended starting.
5/16” Socket
5/16” Socket
Torx T30
Smart Lawn Connect Kit
Installation Instructions
Wire Harness
Connector
2 Remove nal (2) bolts with 3/8” socket and ratchet underneath the Fender in order to disengage it. The
Fender can now be tilted upward to gain access to the back side of the Ignition Switch and Wire Har-
ness Connector. The Wire Harness Connector can now be unplugged (see illustration below).
Ignition Switch
Right Rear Tire
Once all bolts are removed the
fender can be rotated upward.
View looking up
underneath fender
3/8” Socket
3/8” Socket
Smart Lawn Connect Kit
Installation Instructions
3 Note prong conguration and install the Craftsman Smart Lawn Connect Plug onto the Ignition Switch.
Then plug the Wire Harness Connector into the Craftsman Smart Lawn Connect Plug
(refer to illustration below).
Right Rear Tire
Wire Harness
Connector
Ignition Switch
Craftsman Smart
Lawn Connect Plug
View looking up
underneath fender
Smart Lawn Connect Kit
Installation Instructions
Wire Harness
Connector
Ignition Switch
Craftsman Smart
Lawn Connect Plug
Assembly is complete when the Craftsman
Smart Lawn Connect Plug is sandwiched
between the other two components.
Your part may vary slightly in appearance.
Before reassembling the Console, tug on the
ends of the plug assembly. When pushed
together correctly they should not pull apart.
Prongs will be visible here
Wire Harness
Connector
Ignition Switch
Craftsman Smart
Lawn Connect Plug
4 When all three components are plugged together this is how the plug assembly looks (refer to illustration
below). NOTE: The base of the Ignition Switch prongs will be visible in the gap between the Ignition Switch
and the Craftsman Smart Lawn Connect Plug. This is intentional, and allows for proper plug functionality.
Smart Lawn Connect Kit
Installation Instructions
Install (2) additional bolts
(not shown in this illustration)
underneath fender.
5 Once the Plug assembly is secure, move the fender back into place and secure with (5) bolts (1 in front,
2 between fender and seat, and 2 underneath fender) to complete installation (see illustration below).
*The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by [Sears Brands Management Corporation] is under license. Other trademarks and trade names are those of their respective owners.
†Apple and the Apple logo are trademarks of Apple Inc., registered in the U.S. and other countries. App Store is a service mark of Apple Inc. Google Play and Android are trademarks of Google Inc. Sears Brands Management Corporation, Hoffman Estates, IL 60179
For additional information please refer to: craftsman.com/connectkit
If you have further questions, call the Craftsman help line at 1-888-331-4569
Once assembly is complete please download the FREE Craftsman Smart Lawn App to begin using
all of the new connectivity features of your Craftsman rider!
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5

Craftsman 490-900-S068 Operating instructions

Type
Operating instructions

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI