ATC 1000WF Quick start guide

  • Hello! I am an AI chatbot trained to assist you with the ATC 1000WF Quick start guide. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
1
QuickStartGuide
Wi-FiTORS-232/422/485
CONVERTER
MODELATC-1000WF
(Version1.0)
1
1
1
.
CheckPackageContent
ATC-1000WFunit 1Pcs
MonopoleAntenna(2dBiRP-SMA) 1Pcs
SoftwareCD 1Pcs
Externalpoweradapter 1Pcs
PrintedversionofthisATC-1000WFQuickStartGuide
1Pcs
2
2.HardwareInstallation
ConnectRS-232DB9FemaleCrossingconfigurationcable
toATC-1000WFunitonRS-232side.
ConnectingthePowerAdaptertoATC-1000WFpowerjack.
Whenthepowerisproperlysupplied.TheLinkLEDwill
periodictoflashandPWRLEDwilllightinred.
RS-232/422/485Pinouts
RS-232Pinout(DB9Female)
PIN RS-232 Input/Output
2 RXD I
3 TXD O
5 GND -
7 RTS O
8 CTS I
RS-422/485Pinout(SIXTerminalfromLeft)
PIN RS-422 RS-485
1 R+ 485+
2 R- 485-
3 T+ -
4 T- -
5 VIN+ VIN+
6 VIN- VIN+
3
3. LEDindication
LINK----IndicateWLANstatus
ACT ----ItwillflashwhendatatransmitbetweenWLANand
serialport.
PWR----IndicatethePowersupply
4
4.SoftwareInstallation
I
nsertthesoftwareCDandsearchforsuchasF:/Tool/
ATC-1000WFtorunAXR2W_RS232-to-WiFi_Toolkit_32bit
_v1300.exe.
Note:Besureyouhaveadministrativerights&disable
firewallsinwindowsXP
5
5.ConfiguretheATC-1000WF
BeforeconfiguringtheATC-1000WF,youshouldturnoff
thepoweranduseaserialcableconnecttheATC-1000WFto
yourcomputersserialport.
Wesuggestusing Tera-Term tooperate.Firstlyyoushould
configure Tera-Term likebelow.115200bpsforbaud
rate,8bitsfordata-length,NONEforparitybit,1bitforstop
bits.
Uponpowerup,thedevicewillbeindatamode.Toenter
commandmode,youshouldsend ““+++<CR>.Thedevice
willrespondwith uart>.
Whileincommandmode,thedevicewillacceptASCIIbytes
as command. To exit command mode, send
AXCmd2Net.Thedevicewillrespondwith OK todata
mode.
TheparameterssuchastheSSID,channel,IPaddress,serial
portsettings,andallothersettingscanbeviewedand
configuredincommandmode.
6
6.FactoryDefaultWLAN&IPAddress
UARTParameters
Mode: RS-232 | Baud-rate: 115200
Data-length: 8 | Parity: n(none)
Stop-bits: 1 | Flow: n(none)
IPParameters
Protocol: TCPServer
Localport:: 5000
DHCPClient: Enabled
StaticIPAddress: 192.168.2.3
NetMask: 255.255.255.0
Gateway: 192.168.2.1
DHCPServer: Enabled
StartIPAddress: 192.168.2.4
EndIPAddress: 192.168.2.10
NetMask: 255.255.255.0
Gateway: 0.0.0.0
LeaseTime: 1440
2
WLANParameters
Channel:11 | Mode:Ad-Hoc
SSID: R2WiFi | Data-rate:Auto
7
7.
SummaryofCommands
Firstly,ifyouhaveentertheCMDmode,whenyousend
help,likefollowingpicture.
Secondly,allcommandwilldisplayinthewindowof
hyper-terminallikebelow.
TurntoATC-1000WFusermanualfordetaildissipationofthe
command.
8.
QuickconnectioninAPmode
Step1: ConnectoneendofRS-232cabletoPCsCOM
portandtheotherendtoATC-1000WFCOMport.
Step2: Open Tera-Term andenterCMDmode.
Step3: Send setnt0tochangeATC-1000WFtoInfra
mode.
Step4: Send sisrvy todositesurveyanditwilldisplaya
listofAPbeingfound.
Step5: Send jbss tojointothespecificAP,notethatthe
argumentmustbeanindexinthesitesurveyresultlist.For
example.
Step6: Send saveconfig tosavetheconfigurationinto
flash.
Step7: Send reboot torebootATC-1000WF.
Step8: EnterintoCMDmodeagainandsend ipconfig to
checktheIPaddressofATC-1000WFassignbyrouter.
Step9: Send AXCmd2Net returntodatatransmitmode.
9.QuickconnectioninAd-Hocmode
ForATC-1000WFAd-Hocisthedefaultsetting.
Step1: PoweronATC-1000WF.
Step2: Useadevicewithawirelessnetworkcard.Your
laptopordesktopwithwirelessnetworkcardisOK.
Step3: OnyourPC,usethewirelessNetworkConnection
windowapplicationtolookforWiFinetworkwithSSID,said
R2WiFi.
Step4: Press Connect toconnecttoATC-1000WF.
/