Toro 48in E-Z Vac Blower and Drive Kit, 2016 and After Grandstand Mower Installation guide

Brand: Toro

Model: 48in E-Z Vac Blower and Drive Kit, 2016 and After Grandstand Mower

Type: Installation guide

This manual is also suitable for

FormNo.3435-383RevA

48in,52in,or60inE-ZVac

™

BlowerandDriveKit

2016andAfterGrandstand

Mower

ModelNo.78574—SerialNo.403300000andUp

ModelNo.78575—SerialNo.403300000andUp

ModelNo.78576—SerialNo.403300000andUp

InstallationInstructions

Note:InstallthiskittousewiththeE-ZVacTwinBagger;refertotheOperator’sManualforthebagger

forsafety,operation,andmaintenanceprocedures.

Safety

SafetyandInstructionalDecals

Safetydecalsandinstructionsareeasilyvisibletotheoperatorandarelocatednearanyarea

ofpotentialdanger.Replaceanydecalthatisdamagedormissing.

decal136-4087

136-4087

1.Warning—readtheOperator’sManual.4.Cutting/dismembermenthazardofhand,impeller—stayaway

frommovingparts;keepallguardsandshieldsinplace.

2.Warning—wearhearingprotection.

5.Cutting/dismembermenthazardofhand,impeller—disengage

thePTO,removethekey,andwaitforallmovingpartstostop.

3.Thrownobjecthazard—donotoperatethemachinewithout

thecollectionsysteminstalledandlatched.

6.Warning;lossoftractionhazard—donotoperatewithonlythe

counterbalanceweightsinstalled;donotoperatewithonlythe

E-ZVacinstalled;onlyoperatewithboththeE-ZVacand

counterbalanceweightsinstalled.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3435-383*A

Installation

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

Nopartsrequired

–

Preparethemachine.

Nopartsrequired

–

Removethedischargechuteandbelt

cover.

Blowermount1

Bolt(1/2x1-1/2inches)

Lockwasher1

Nut(1/2inch)

Bolt(3/8x1-1/4inches)

Nut(3/8inch)

Carriagebolt(3/8x1-1/4inches)

Carriagebolt(3/8x1inch)

Idlerassembly1

Pulleyassembly1

Installthepulleyandidlerassemblies

(formachineswithacast-ironspindle).

Pulleyassembly1

Pulley-platemount1

Flangenut(3/8inch)

Installthepulleyassemblyandbelt(for

machineswithanaluminumspindle).

Blowerassembly1

Belt1

Beltcover1

Knob1

Installtheblowerassembly,belt,and

beltcover.

Note:Determinetheleftandrightsidesofthe

machinefromthenormaloperatingposition.

PreparingtheMachine

NoPartsRequired

Procedure

Performthefollowingproceduretopreparethe

machineforattachingtheblowerandnishingkit.

1.DisengagethePTO,movethemotion-control

leverstotheNEUTRAL-LOCKposition,andsetthe

parkingbrake.

2.Shutofftheengine,removethekey,andwait

forallmovingpartstostopbeforeleavingthe

operatingposition.

3.Repairallbentordamagedareasofmower

deckandreplaceanymissingparts.

4.Cleanthemachineofanydebrisonthedeckor

rearpartofthemachinetoeaseinstallation.

RemovingtheDischarge

ChuteandExistingBelt

Cover

NoPartsRequired

Procedure

Note:Retainallpartsforwhenyouremovethe

bagger.

1.Removethebolt(5/16x7-1/2inches)andnut

(5/16inch)securingthedischargechutetothe

deck.Removethechute,spring,andspacer

(Figure1).

g037552

Figure1

1.Dischargechute

4.Spring

2.Nut(5/16inch)5.Spacer

3.Beltcover

6.Bolt(5/16x7-1/2inches)

2.Removethebeltcover(Figure1).

3.Removethewireform,carriagebolt,and3nuts

(3/8inch)fromthedeck.

Note:Youwillusethesenutstoinstalltheidler

assemblyin3InstallingthePulleyandIdler

Assemblies(page4).

g037553

Figure2

1.Wireform3.Nut(3/8inch)

2.Carriagebolt(3/8x1inch)

InstallingthePulleyand

IdlerAssemblies

ForMachineswithaCast-Iron

Spindle

Partsneededforthisprocedure:

1Blowermount

Bolt(1/2x1-1/2inches)

1Lockwasher

Nut(1/2inch)

Bolt(3/8x1-1/4inches)

Nut(3/8inch)

Carriagebolt(3/8x1-1/4inches)

Carriagebolt(3/8x1inch)

1Idlerassembly

1Pulleyassembly

Procedure

1.Installtheblowermounttothedeckusing1bolt

(1/2x1-1/2inches),1lockwasher,1nut(1/2

inch),1bolt(3/8x1-1/4inches),and1nut(3/8

inch)asshowninFigure3.

Note:Youmayneedtoloosenthe3bafebolts

whenyouinstalltheblowermounttoalignthe

assemblywiththedeck.Tightentheboltsafter

installingthemount.

g194670

Figure3

1.Nut(3/8inch)5.Bolt(1/2x1-1/2inches)

2.Blowermount6.Lockwasher

3.Bolt(3/8x1-1/4inches)7.Nut(1/2inch)

4.Bafebolt(3)

2.Removethenutsfromthespindleintheright

deckpulleyandusethemtoattachthepulley

assemblytothedeckpulley(Figure3).

Note:Youmayneedtoremovethemowerbelt

torelievethetensionoffthedeckpulleywhen

youinstallthepulleyassembly.Refertothe

Operator’sManualforthemachine.

g037507

Figure4

1.Nut

3.Spindle

2.Pulleyassembly

3.Usingthe3nutsthatyouremovedpreviously,1

carriagebolt(3/8x1-1/4inches),and2carriage

bolts(3/8x1inch),installtheidlerassemblyto

themowerdeck(Figure4).

g037508

Figure5

1.Carriagebolt(3/8x1-1/4

inches)

3.Carriagebolt(3/8x1inch)

2.Idlerassembly

4.Nut(belowthemower

deck)

InstallingthePulley

AssemblyandBelt

ForMachineswithanAluminum

Spindle

Partsneededforthisprocedure:

1Pulleyassembly

1Pulley-platemount

Flangenut(3/8inch)

Procedure

1.Removethetopnut,washer,andsheavefrom

thespindle(Figure6).

Note:Notetheorientationofthesheavewhen

youremoveitfromthespindletoensurethat

youinstallitproperlylaterintheprocess.

g302393

Figure6

1.Topnut

3.Sheave

2.Washer

4.Spindle

2.Insertthepulley-platemountstudsintotheholes

inthesheave(Figure7).

g302390

Figure7

1.Sheave

2.Pulley-platemountstuds

3.Looselyinstallthe3nutstothestuds(Figure8).

Leaveaclearanceof5mm(3/16inch)between

thenutandsheave.

g302412

Figure8

1.Nut

2.Stud

4.Installthesheaveassemblytothespindleusing

thewasherandtopnut(Figure9).

g302413

Figure9

1.Topnut

3.Sheaveassembly

2.Washer

4.Spindle

5.Torquethetopnutto176to217N∙m(130to

160ft-lb).

Note:Ensurethatthesheavespinsfreely.

6.Alignthenewpulleyassemblysothatthe

openingstoverthenuts(Figure10).

g302411

Figure10

1.Pulleyassembly2.Nuts

7.Turnthepulleytolockitintoposition(Figure11).

Note:Ifthepulleydoesnotturn,loosenthe

nutsmoretoraisethenutsandallowthepulley

tolockintoposition.

g302414

Figure11

1.Pulleyassembly

8.Afterthenewpulleyassemblyisinposition,

tightenthenutstosecurenewpulleyassembly.

Torquethe3nutsto28to34N∙m(21to25ft-lb).

9.Installthedeckbelt.

InstallingtheBlower

Assembly,Belt,andBelt

Cover

Partsneededforthisprocedure:

1Blowerassembly

1Belt

1Beltcover

1Knob

Procedure

RefertothebaggerOperator’sManualforthecorrect

proceduretoinstalltheblowerassembly,belt,and

beltcovers.

Toro 48in E-Z Vac Blower and Drive Kit, 2016 and After Grandstand Mower Installation guide

Brand: Toro

Model: 48in E-Z Vac Blower and Drive Kit, 2016 and After Grandstand Mower

Type: Installation guide

This manual is also suitable for

Download PDF

report

Toro 48in E-Z Vac Blower and Drive Kit, 2016 and After Grandstand Mower Installation guide

This manual is also suitable for

Toro 48in E-Z Vac Blower and Drive Kit, 2016 and After Grandstand Mower Installation guide

Related papers

Other documents