Elizabethan Classics ECRM23 ORB Installation guide

Brand: Elizabethan Classics

Model: ECRM23 ORB

Category: Sanitary ware

Type: Installation guide

This manual is also suitable for

The Elizabethan Classics ECRM23 ORB is a versatile and stylish bathroom faucet that combines durability with ease of use. Crafted with high-quality materials, it features a sturdy brass construction that ensures longevity and resistance to corrosion. This faucet boasts a sleek orb finish that adds a touch of elegance to your bathroom decor. Its ergonomic design includes lever handles for effortless water flow control and temperature adjustment.

Assembly Instructions for 3V3LSA

NOTE: USE TEFLON TAPE ON ALL THREADED CONNECTIONS

1. Shut off the water supply valves before installation.

2. According to your requirement, connect the riser or swivel arm connector kit to the faucet body.

3. Attach the diverter lever onto diverter valve and tighten the diverter screw.

3. Install handles. After installation is completed. Turn on the water supply valves and allow both hot

and cold water to run at least one minute each. While water is running. Check for leaks,

especially at hook-ups to supply lines. Tightening nuts slightly will stop any minor leaks.

Diverter lever

Diverter screw

Lever Handles:

1. Be sure that the broach screws are tightened installing the lever handles.

2. Install the lever handles on the broaches and tighten the set screws using the allen

wrench provided.

before

Cross Handles:

1. Remove the screws from the top of the broaches.

2. Remove the insert caps from the cross handles.

3. Put the cross handles on the broaches and then tighten the screws. Insert the caps on the

cross handles.

Broach

Screw

Set

Screw

Allen

Wrench

Assembly Instructions for Handles

Rev.D

Elizabethan

Classics

NOTE: TO BE INSTALLED ONLY BY QUALIFIED, LICENSED PLUMBER

CAUTION: DO NOT OVER TIGHTEN NUTS AND SCREWS - THIS CAN LEAD TO

STRIPPING OR CRACKING AND WILL VOID YOUR WARRANTY.

RM21-25

Assembly Instructions for 6RMN

NOTE: USE TEFLON TAPE ON ALL THREADED CONNECTIONS

1. Shut off the main water supply valves before installation.

2. Thread the Brass Nipple into Supply Shank.

3.Insert Rubber Washers into Coupling Nuts. Thread faucet onto

90 degree elbow and tighten the Coupling nuts.

4. .

5.Tighten the Mounting Nuts.

6.Place Supply Line Nuts, Friction Rings, and Cone Washers onto

supply line coming out from floor. Connect the Brass Nipples and

tighten wrench tight. CAUTION:

Get Brass Nipples through the faucet holes

DO NOT OVERTIGHTEN.

Elizabethan

Classics

Rev.A

90 degree elbow

CAUTION: DO NOT OVER TIGHTEN NUTS - THIS CAN LEAD TO

STRIPPING OR CRACKING AND WILL VOID YOUR

WARRANTY.

NOTE: TO BE INSTALLED ONLY BY QUALIFIED, LICENSED PLUMBER

Brass Nipple

Tub Deck

Mounting Nut

Cone Washer

Friction Ring

Supply Line Nut

Faucet Hole

Coupling Nut

Rubber Washer

Supply Shank

NOTE : REQUIRE ECSSL STRAIGHT BATH SUPPLY LINES WHICH

INCLUDE SUPPLY LINE NUTS, FRICTION RINGS, AND CONE

WASHERS.

Faucet

Rev.E

Elizabethan

Classics

NOTE: TO BE INSTALLED ONLY BY QUALIFIED, LICENSED PLUMBER

NOTE: USE TEFLON TAPE ON ALL THREADED CONNECTIONS

CAUTION: DO NOT OVER TIGHTEN NUTS - THIS CAN LEAD TO STRIPPING OR

CRACKING AND WILL VOID YOUR WARRANTY.

AND SCREWS

RM21-25

Elizabethan Classics ECRM23 ORB Installation guide

Brand: Elizabethan Classics

Model: ECRM23 ORB

Category: Sanitary ware

Type: Installation guide

This manual is also suitable for

Download PDF

report

Elizabethan Classics ECRM23 ORB Installation guide

This manual is also suitable for

Elizabethan Classics ECRM23 ORB Installation guide

Related papers

Other documents