Dixon Rotary Lobe Pumps - JRZL-200 Series User manual

Operating & Maintenance Manual

for

JRZL-200 Series

Rotary Lobe Pumps

Dixon Sanitary

N25 W23040 Paul Road • Pewaukee, WI 53072

ph: 800.789.1718 • fx: 800.789.4046

dixonvalve.com

2 Rotary Lobe Pumps - JRZL-200 Series800.789.1718

Table of Contents

Safety ................................................................................................................................................................................................... 3

Care of Stainless Steel ......................................................................................................................................................................... 4

Technical Specications ....................................................................................................................................................................... 5

Curves ............................................................................................................................................................................................... 6-9

Unpacking Installation & Start Up .................................................................................................................................................. 10-19

Tools needed ...................................................................................................................................................................................... 20

Maintenance .................................................................................................................................................................................. 20-58

Pump Housing Disassembly ...................................................................................................................................................... 20-51

Single Mechanical Seal .......................................................................................................................................................... 20-28

Double Mechanical Seal......................................................................................................................................................... 29-38

Single O-ring Seal .................................................................................................................................................................. 39-44

Triple Lip Seal ........................................................................................................................................................................ 45-51

Inspection........................................................................................................................................................................................ 52

Pump Housing Assembly ................................................................................................................................................................ 52

Rotor Clearance ......................................................................................................................................................................... 53-55

Shimming ............................................................................................................................................................................... 54-55

Rotor Timing ................................................................................................................................................................................... 56

Gear Box Disassembly ................................................................................................................................................................... 57

Gear Box Assembly ........................................................................................................................................................................ 58

Scheduled Maintenance ................................................................................................................................................................. 58

Maximum RPM ................................................................................................................................................................................... 59

Maximum Solids ................................................................................................................................................................................. 59

Dimensions ......................................................................................................................................................................................... 60

Troubleshooting ............................................................................................................................................................................. 61-63

Repair Kits .......................................................................................................................................................................................... 64

BOM .............................................................................................................................................................................................. 65-76

Certicates..................................................................................................................................................................................... 77-78

Warranty ............................................................................................................................................................................................. 79

Thank you for purchasing a Dixon Sanitary Product!

This manual contains installation, operation, disassembly and assembly instructions, maintenance procedures, troubleshooting and a

complete parts list for all JRZL-Series positive displacement pumps.

READ THIS MANUAL carefully to learn how to service these pumps. Failure to do so could result in person injury or equipment

damage.

3Rotary Lobe Pumps - JRZL-200 Series 800.789.1718

DO’S & DON’TS

DO read and understand these instructions before installing or using the pump.

DO use Dixon spare parts when replacing a component of the pump.

DO NOT service the pump while it is running.

DO NOT place the pump in an application where the service ratings are exceeded.

DO NOT modify the pump. Modifying the pump creates unsafe conditions and voids all warranties.

SAFETY PRECAUTIONS WHEN INSTALLING PUMP

DO use an authorized electrician when connecting the pump.

DO observe the mechanical limits of the pump (refer to the pump performance sheet).

DO install a throttling valve in the discharge line.

DO NOT install a throttling valve in the suction line.

SAFETY PRECAUTIONS WHEN OPERATING PUMP

DO allow only qualied personnel to operate this pump.

DO NOT start the pump until all personnel are clear.

DO NOT touch the pump or the lines when pumping hot uids or when performing Clean In Place (CIP) procedures.

DO NOT run the pump with BOTH the suction inlet and discharge outlet blocked. Running the pump with the inlet

blocked will cause serious damage to the pump.

DO NOT check pump rotation with liquid in the pump.

DO NOT run the pump with the front cover removed. The rotors and rotor case could be damaged or may cause severe

injury.

DO NOT operate the pump with the safety guard removed.

SAFETY PRECAUTIONS WHEN SERVICING PUMP

DO ensure the pump is cool to touch before performing service.

DO relieve all pressure and drain all uids from pump and connected piping before performing service.

DO ENSURE POWER TO THE UNIT HAS BEEN DISCONNECTED PRIOR TO PERFORMING ANY PUMP

MAINTENANCE OR CLEANING.

DO exercise caution and wear protective clothing when using lye or acid for cleaning.

Safety Information

4 Rotary Lobe Pumps - JRZL-200 Series800.789.1718

Care of Stainless Steel

The stainless steel components in Dixon Sanitary equipment are machined, welded and assembled by skilled craftsmen using

manufacturing methods that preserve the corrosion-resistant quality of the stainless steel.

Retention of corrosion-resistant qualities under processing conditions requires regular attention to the precautions listed below.

1. Regularly check all electrical devices connected to the equipment for stray currents caused by improper grounding, damaged

insulation or other defects. Corrosion: Pitting often occurs when stray currents come in contact with moist stainless steel.

2. Never leave rubber mats, ttings, wrenches, etc. in contact with stainless steel. Corrosion: Pitting or galvanic action. Objects

retard complete drying, preventing air from reforming the protective oxide lm. Galvanic corrosion occurs when two dissimilar

metals touch when wet.

3. Immediately rinse equipment after use with warm water until the rinse water is clear. Clean the equipment (manual or CIP)

as soon as possible after rinsing. Corrosion: discoloration, deposits, pitting. Product deposits often cause pitting beneath the

particles.

4. Use only recommended cleaning compounds. Purchase chemicals from reputable and responsible chemical manufacturers

familiar with stainless steel processing equipment, they continuously check the effects of their products on stainless steel.

5. Use cleaning chemicals exactly as specied by the manufacturer. Do not use excessive concentrations, temperatures or exposure

times. Corrosion: Pitting, discoloration, stress cracks. Permanent damage often occurs from excessive chemical concentrations,

temperatures or exposure times.

6. For manual cleaning, use only soft non-metallic brushes, sponges or pads. Brush with the grain on polished surfaces, avoid

scratching the surface. Corrosion: Pitting, scratches. Metal brushes or sponges will scratch the surface and promote corrosion

over a period of time. Metal particles allowed to remain on a stainless steel surface will cause pitting.

7. Use chemical bactericides exactly as prescribed by the chemical manufacturer in concurrence with local health authority. Use

the lowest permissible concentration, temperature and exposure time possible. Flush immediately after bacterial treatment. In no

case should the solution be in contact with stainless steel more then 20 minutes. Corrosion: Protective lm destroyed. Chlorine

and other halogen bactericides can destroy the protective lm. A few degrees increase in temperature greatly increases chemical

activity and accelerates corrosion.

8. Regularly inspect the joints in pipelines. Be sure all connections are tight tting without binding. Corrosion: Crevice corrosion.

Small crevices caused by improperly seated gaskets will promote crevice corrosion. Stainless steel under stress will develop

stress cracking especially in the presence of bactericides containing chlorine.

9. Regularly inspect equipment for surface corrosion (i.e. pitting deposits, stress cracks, etc.). If deposit or color corrosion is

detected, remove it immediately using mild scouring powder and detergents. Rinse thoroughly and allow to air dry. Review

production and cleaning procedures to determine the cause. Note: If corrosion is not removed, the protective lm cannot be

restored and corrosion will continue at an accelerated rate.

5Rotary Lobe Pumps - JRZL-200 Series 800.789.1718

JRZL 200-Series Technical Data

Specications:

Model

Maximum Differential

Pressure (PSI)

1

Maximum Flow Rate

(GPM)

Temperature

Range

Viscosity

Range

Noise

Level

220 174 76

14°F to 356°F (-10°C to 180°C)

above 248°F (120°C) may require

Hot Clearance Rotors

Up to

1,000,000 cPs

60 ~ 80 dB

225 116 114

1

Up to 435 PSI (30 bar) is available with Front Bearing Cover

Materials:

• Product wetted steel part: AISI 316L Stainless Steel (standard)

• Product wetted elastomers: EPDM (standard)

• Optional seals: Buna, FKM

Shaft Seals:

• Seal options: Single and Double Mechanical, Single and Double O-Ring and Triple Lip-seal

• Maximum ushing water pressure: 7 PSI (0.5 bar)

• Flushing water consumption: 30~60 cubic inches/min (0.25~0.5 liter/min)

• Flush inlet at lowest port on casing

• Stationary seal ring material: Tungsten Carbide

• Rotating seal ring material: Tungsten Carbide (standard) or Silicon Carbide (optional)

• O-ring material: EPDM (standard)

• Optional O-ring material: Buna, FKM

• Triple lip seal material: PTFE(Polytetrauoroethylene)+Glass (standard) or PTFE+Copper (optional)

Rotor Information: Not all rotors available in all models.

• Single/bi-wing and bi-lobe/tri-lobe/heli-lobe are interchangeable

• Optional rotors: Multi-lobe, Hardened

Optional Information:

• Ultra clean version

• High pressure version up to 435 PSI (30 bar)

• Heating jacket on rotor case and front cover

• Rectangular inlet version

• Pressure relief front cover (not 3A)

• Surface hardening

6 Rotary Lobe Pumps - JRZL-200 Series800.789.1718

JRZL 220 Curves

Rotary Lobe Pump JRZL220

APPLIES TO BI-WING, BI-LOBE, AND SINGLE WING* ROTORS

* SINGLE WING ROTOR MAX 100 RPM

PORT SIZE: 2 X 2



















     































  









  









  









  

















Dixon Sanitary

N25 W23040 Paul Road • Pewaukee, WI 53072

Customer Service: 800.789.1718

Fax: 800.789.4046

dixonvalve.com

7Rotary Lobe Pumps - JRZL-200 Series 800.789.1718

JRZL 220 NPSHR Curves

Rotary Lobe Pump JRZL220

NET POSITIVE SUCTION HEAD REQUIRED

PORT SIZE: 2 X 2

Dixon Sanitary

N25 W23040 Paul Road • Pewaukee, WI 53072

Customer Service: 800.789.1718

Fax: 800.789.4046

dixonvalve.com

0

5

10

15

20

25

0 100 200 300 400 500 600 700

NPSHR (PSIA)

SPEED (RPM)

8 Rotary Lobe Pumps - JRZL-200 Series800.789.1718

JRZL 225 Curves

Rotary Lobe Pump JRZL225

APPLIES TO BI-WING, BI-LOBE, AND SINGLE WING* ROTORS

* SINGLE WING ROTOR MAX 100 RPM

PORT SIZE: 2.5 X 2.5



















     































  









  









  









  

















Dixon Sanitary

N25 W23040 Paul Road • Pewaukee, WI 53072

Customer Service: 800.789.1718

Fax: 800.789.4046

dixonvalve.com

9Rotary Lobe Pumps - JRZL-200 Series 800.789.1718

JRZL 225 NPSHR Curves

Rotary Lobe Pump JRZL225

NET POSITIVE SUCTION HEAD REQUIRED

PORT SIZE: 2.5 X 2.5

Dixon Sanitary

N25 W23040 Paul Road • Pewaukee, WI 53072

Customer Service: 800.789.1718

Fax: 800.789.4046

dixonvalve.com

0

5

10

15

20

25

0 100 200 300 400 500 600 700

NPSHR (PSIA)

SPEED (RPM)

10 Rotary Lobe Pumps - JRZL-200 Series800.789.1718

Unpacking

Carefully unpack all parts of the pump and inspect for damage that may have occurred during shipment. Report any damages to the

carrier immediately.

The ports on the pump are protected with a plastic cover. If any covers are missing or damaged, inspect the ports on the pump

thoroughly for any damage.

If you are receiving a complete base mounted unit, please check shaft alignment as it may have changed during shipment.

The drawing below shows how the pump should be lifted. Ensure that the lifting equipment is correctly rated.

11Rotary Lobe Pumps - JRZL-200 Series 800.789.1718

Installation & Start Up

Pump Mounting Adjustable:

• Adjustable leg base, commonly used for sanitary pumps for wash down under base. Can be easily moved or repositioned.

Mounting Congurations

Pump Mounting Casters:

• Portable bases – for movement to different locations. Can also be mounted on a cart with handles.

12 Rotary Lobe Pumps - JRZL-200 Series800.789.1718

Installation & Start Up

Proper Installation

Piping Support:

• Weight of piping and uid – support piping independently with hangers or pedestals. On rectangular inlet ange pumps, hopper

should also be supported independently.

13Rotary Lobe Pumps - JRZL-200 Series 800.789.1718

Installation & Start Up

Proper Installation (continued)

Piping Slope:

• Inlet side – slope piping up to inlet to avoid air pocket.

14 Rotary Lobe Pumps - JRZL-200 Series800.789.1718

Installation & Start Up

Proper Installation (continued)

Pressure Gauges:

Pressure and vacuum gauges provide the easiest way to tell you something about the pump operation.

• Normal or abnormal pressures

• Overow conditions

• Indication of ow

• Changes in pump condition

• Changes in system conditions

• Changes in uid viscosity

15Rotary Lobe Pumps - JRZL-200 Series 800.789.1718

Installation & Start Up

Proper Installation (continued)

Inlet Check Valve:

• Inlet side – use check valves to keep inlet line full, particularly with low viscosity uids, and in start-stop operation.

Outlet Check Valve:

• Inlet Vacuum Service – use check valve on outlet side.

• Prevents backow (air or uid)

• Facilitates initial start-up (minimizes differential pressure pump must supply to start ow)

16 Rotary Lobe Pumps - JRZL-200 Series800.789.1718

Installation & Start Up

Proper Installation (continued)

Thermal Expansion:

• Thermal expansion of piping can cause tremendous forces. Use thermal expansion joints to minimize forces on pump. Flexible

joints can also be used to limit the transmission of mechanical vibration. Anchor free ends of any exible hose in system.

Isolation Valves:

• Isolation Valves – permit pump maintenance and removal safely without emptying entire system.

17Rotary Lobe Pumps - JRZL-200 Series 800.789.1718

Installation & Start Up

Proper Installation (continued)

Relief Loop:

• Relief Valve – To protect the pump and piping system against excessive pressure, a relief valve should be installed. An integral

relief valve, designed to bypass the uid internally from the pump outlet to the inlet, should not be used on applications where the

discharge must be closed for more than a few minutes. Prolonged operation of the pump with closed discharge with cause heating

of the uid circulating through the relief valve.

18 Rotary Lobe Pumps - JRZL-200 Series800.789.1718

Installation & Start Up

At Start Up

Pump Flow:

• All pumps are labeled with ow direction based on motor being wired for clockwise rotation. If motor is wired for counterclockwise

rotation, ow direction will be opposite of what is indicated on pump head.

19Rotary Lobe Pumps - JRZL-200 Series 800.789.1718

Installation & Start Up

At Start Up

Pump Alignment:

• A exible coupling is used to compensate for end play and small differences in alignment. The pump and drive shaft should be

aligned as closely as possible.

• Check angular alignment using feeler or taper gauge.

• Adjust to get equal dimension at all points – at the same time, set space between coupling halves to the coupling manufacturer’s

recommended distance.

• Note: Pump is aligned prior to shipping, after installation verify alignment as misalignment may have occurred during shipment.

20 Rotary Lobe Pumps - JRZL-200 Series800.789.1718

Tools Needed

• Rotor tool

• Plastic dowel

• Open ended wrench set

• Rubber mallet

• Flat head screw driver

• Feeler gauges

• Hex keys

• O-ring pick

• Spanner wrench

• Rotor extraction tool (optional)

Additional tools needed when assembling or disassembling gear box

• Spanner wrench

• Arbor press or bearing puller

Maintenance

Pump Housing Disassembly - Single Mechanical Seal

Prior to removal of pump, the shut-off valves in the suction and discharge lines must be closed. If there is any risk that product

may harden, crystallize or freeze in the pump it should be thoroughly drained and cleaned immediately after use. Same

attention applies if there is a seal ush option. Power needs to be locked out to prevent unintended start of the pump.

Note: Reference numbers are listed in the sectional view located on pages 61-73.

1. Loosen and remove the four hex nuts (33) from the front cover.

Page is loading ...

Dixon Rotary Lobe Pumps - JRZL-200 Series, JRZL-200 Series Rotary Lobe Pumps User manual

Related papers

Other documents