Page is loading ...
FormNo.3402-997RevD
LightKit
GrandStand
®
Mower
ModelNo.133-1437
InstallationInstructions
Note:Determinetheleftandrightsidesofthemachinefromthenormaloperatingposition.
Note:Installthiskitbeforeinstallingotheraccessorieswithawireharness.
Installation
LooseParts
Usethechartbelowtoverifythatallpartshavebeenshipped.
Description
Qty.
Use
Lightassembly1
Rearlight1
Spacer
1
Bolt2
Nut2
Lightswitch1
Installthelights.
Cableties
6Routethewireharness.
InstallingtheLights
1.Shutofftheengine,waitforallmovingpartsto
stop,engagetheparkingbrake,andremove
thekey.
2.Removethenegative(-)batterycablefromthe
battery.
3.Removethefueltank;refertotheOperator’s
Manualforthemachine.
4.Removeanddiscardtheknock-outfromthe
towerpanel(Figure1).
g033845
Figure1
1.Lightswitch2.Knock-outlocation
©2019—TheToro®Company
8111LyndaleAvenueSouth
Bloomington,MN55420
Registeratwww.Toro.com.
OriginalInstructions(EN)
PrintedintheUSA
AllRightsReserved
*3402-997*D
5.Installthelightswitch(Figure1).
6.Mountthelightassemblytothefrontofthe
controlpanelusing2boltsand2nuts(Figure2).
g033849
Figure2
WireHarnessNotShown
1.Lightassembly3.Nut
2.Bolt
7.Removethebolt,washer,andnutfromtherear
lightandusethemtoinstalltherearlightand
spacerontherightsideofthecontrolpanel
(Figure3).
Note:Ifthereisnohole,drillaholeusinga
3/8-inchdrillbit.
g034171
Figure3
1.Nut4.Rearlight
2.Lockwasher5.Bolt
3.Spacer
RoutingtheWireHarness
1.Routethewireharnessunderthefrontofthe
controlpanelandplugtheconnectorsintothe
lightswitchandthewireharnessforthemachine
(Figure4andFigure5).
Note:Theother3connectorsonthewire
harnessareusedwithotheraccessories
(soldseparately)forthemachine.Ifanother
accessoryisalreadypluggedintothemachine
wireharness,unplugitandplugitintoalight
kitaccessoryconnector.Donotplugthelight
kitintothewireharnessforanaccessory;
otherwise,thelightsmaynotfunction.
Ifyouinstallanotherelectricalaccessory,plugit
intothelightkitaccessoryconnectorinsteadof
themachinewireharness.
g033868
Figure4
1.Wireharness
g033869
Figure5
1.Plugintothelightswitch.3.Machinewire-harness
connector
2.Lightswitch4.Plugintothewire-harness
connector.
2
2.Routethewireharnesstotherearofthe
machineandplugtheconnectorintotherear
light(Figure6).
g036217
Figure6
1.Rearlight2.Wireharness
3.Securethewireharnesstothemachinewith
cableties.
Note:Ensurethatnoneofthewiresinterfere
withtheoperatorcushionortheheight-of-cut
lever.
4.Installthefueltank;refertotheOperator’s
Manualforthemachine.
Important:Ensurethatthewireharnessis
routedabovethefueltankandbracket,not
totheside.
5.Raisethecushion.
6.Installthenegative(-)batterycabletothe
battery.
3
/