American Standard 7455451.013 Installation guide

American Standard
Brand
American Standard
Model
7455451.013
Category
Sanitary ware
Type
Installation guide

This manual is also suitable for

- 1 -
Product names listed herein are trademarks of AS America, Inc.
© AS America, Inc. 2018
Thank you for selecting American Standard...
the benchmark of fine quality for over 140 years.
To ensure that your installation proceeds smoothly-please read
these instructions carefully before you begin.
RECOMMENDED TOOLS
ROUGH-IN DIMENSIONS
1
INSTALL VALVE BODY
Town Square
®
S
Wall Mount Faucet
INSTALLATION
INSTRUCTIONS
7455451
Certied to comply with ANSI A112.18.1M
CAUTION
Turn off hot and cold water
supplies before begining.
M965962 (5/18)
• Determine where the nished wall location will be. This measurement
is very important! NOTE: The rough-in measurement from the nished
wall is; 2" minimum and 3" maximum. This is a 1" tolerance.
See rough-in illustration above.
• Secure FAUCET BODY (1) to cross brace of wall structure
at required height using two wood screws.
• Connect HOT water supply to left VALVE inlet and COLD
water supply to right VALVE inlet. Use pipe sealant or
Teon tape forall threaded connections. For sweat connections,
do not makesweat connections directly to valve body.
Damage to seals and and valve cartridge may occur.
• Turn valves to off position. Turn hot and cold supplies on and
check tting connections for leaks .
• Complete wall construction.
Adjustable Wrench
Flat Blade Screwdriver
Channel LocksPipe WrenchTeon Tape
Tubing Cutter
Plumbers' Putty or
Caulking
FINISHED
WALL
2-1/4" D.
(57 mm)
8-7/8"
(225 mm)
1"
(25 mm)
2" MIN.
(51 mm)
3" MAX.
(76 mm) MAX.
1
WOOD SCREWS
HOT
COLD
CROSS BRACE
WALL STUDS
16"
M
A
X
W
A
L
L
M
I
N
1
-
5
/
8
"
D
E
E
P
M
A
X
W
A
L
L
M
I
N
1
-
5
/
8
"
D
E
E
P
- 2 -
M965962 (5/18)
3
4
INSTALL HANDLES
DRAIN INSTALLATION
• Apply a bead of PUTTY to underside of FLANGE on DRAIN BODY (1).
• Feed DRAIN BODY (1) down through lavatory.
• Assembly GASKET (2) WASHER (3) and LOCKNUT (4) onto DRAIN BODY (1).
Tighten LOCKNUT (4) rmly.
• Assembly TAILPIECE (5) to DRAIN BODY (1).
2
INSTALL DRAIN FROM BELOW FIXTURE
GROOVE
GROOVE
FINISHED WALL
1
1
4
9
5
6
7
4
2
TURN SPOUT 180˚
AERATOR
Figure A
1
M
A
X
W
A
L
L
M
I
N
1
-
5
/
8
"
D
E
E
P
M
A
X
W
A
L
L
M
I
N
1
-
5
/
8
"
D
E
E
P
3
8
4
5
2
3
1
LAVATORY
PUTTY
2
3
4
5
1
• Turn VALVE STEMS (1) to off position.
• Place SEAL (2) into HANDLE BASE (3).
• Thread HANDLE ESCUTCHEON (4) onto VALVE (5)
until snug against nished wall.
• Remove PLASTER GUARDS (1) from valve bodies and SPOUT NIPPLE (3).
• Inspect that SPOUT NIPPLE O-RING (2) is seated in groove of SPOUT NIPPLE (3).
• T hread SPOUT MOUNT (4) onto SPOUT NIPPLE (3). Align groove on SPOUT MOUNT (4) with face of nished wall.
See Figure A.
• Install SEAL (5) into SPOUT BASE (6). Push SPOUT (7) with SEAL (5)
onto SPOUT MOUNT (4) ush against nished wall.
• Insert SPOUT (7) upside down with the aerator facing up.
Tighten the SPOUT SET SCREW (8) with the 3 mm hex
wrench (9) supplied.
• Turn SPOUT (7) 180˚ and align until SPOUT (7) tightens
against the wall.
- 3 -
6
7
CARE INSTRUCTIONS:
TEST INSTALLED FITTING
5
M965962 (5/18)
DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.
DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A
CLOTH WITH A COARSE SURFACE.
SERVICE
CAUTION
Turn off hot and cold water
supplies before begining.
TO REMOVE
HANDLE
90˚
3
2
5
4
1
3
2
1
1
AERATOR
SET
SCREW
• To change direction of handle rotation, proceed as follows:
— Turn valve to OFF position.
— Thread counter-clock wise HANDLE BASE (1) to remove
HANDLE ASSEMBLY (2) from VALVE HOUSING (3).
— Thread counter-clock wise VALVE HOUSING (3) to remove.
— Use a at blade screw driver to remove SPRING CLIP (4).
— Lift STOP WASHER (5), turn 90˚ and replace.
— Replace SPRING CLIP (4).
— Reinstall all parts and HANDLE ASSEMBLY (2).
• If spout drips, operate handles several times from OFF to ON
position. Do not force - handles turn only 90˚.
• With HANDLES (1) in OFF position, turn on WATER
SUPPLIES (2) and check all connections for leaks.
• Remove AERATOR (2).
• Operate both HANDLES (1) to ush water lines thoroughly.
• Replace AERATOR (3).
• Check all drain connections for leaks.
- 4 -
M953455-YYY0A
DRAIN COMPLETE
M970517-YYY0A
HANDLE KIT
A918305-0070A
HANDLE SCREW
617852-0070A
ADAPTER
A912699-0070A
SEAL
994053-0070A
CARTRIDGE
621423-0070A
VALVE HOUSING
M923840-0070A
AERATOR (1.2 GPM)
- 4 -
M965962 (5/18)
Town Square
®
S
Wall Mount Faucet
MODEL NUMBER
7455451
Replace the “YYY” with
appropriate finish code
POLISHED CHROME 002
POLISHED NICKEL 013
LEGACY BRONZE 278
SATIN NICKEL 295
HOT LINE FOR HELP
For toll-free information and answers to your questions, call:
1 (800) 442-1902
Mon. - Fri. 8:00 a.m. to 8:00 p.m. EST
Saturday 10:00 a.m. to 4:00 p.m. EST
IN CANADA 1-800-387-0369
(TORONTO 1-905-306-1093)
Weekdays 8:00 a.m. to 7:00 p.m. EST
IN MEXICO 01-800-839-1200
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

American Standard 7455451.013 Installation guide

American Standard
Brand
American Standard
Model
7455451.013
Category
Sanitary ware
Type
Installation guide
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents