Simplicity 00776-2 User manual

Brand: Simplicity

Model: 00776-2

Category: High-pressure cleaners

Type: User manual

1300PSI

The Reliable Ones

High Pressure Washer

Owners Manual

Problems?

Questions?

Before taking your unit

back to the store,

call the pressure washer

helpline at

1-800-270-1408

M-F 8-5 CST

GENERAC

This symbol points out important safety instructions, which, if not followed, could endan-

ger the personal safety and/or property of yourself and others. Read and follow all

instructions in the manual before attempting to operate this unit.

Model No. 0776-2 (1.5 gpm High Pressure Washer) Manual No. B2490 Revision 1 (06/23/98)

CAUTION! Read all instructions

before using this product to reduce

the risk of injury.

DANGER! Risk of electrocution!

 Inspect cord before every use. Do not use if cord is

damaged.

 Keep all connections dry and off the ground.

 Do not touch plug with wet hands.

 Double-insulated  When servicing, use only iden-

tical replacement parts.

 This product shall only be connected to a power

supply receptacle protected by a Ground Fault Cir-

cuit Interrupter (GFCI).

 Read instruction manual before using.

WARNING! To reduce the risk of

injury, close supervision is neces-

sary when product is used near

children.

 Know how to stop the product and bleed the pres-

sure quickly. Be thoroughly familiar with controls.

 Stay alert. Watch what you are doing.

 Do not operate the product when fatigued or under

the influence of alcohol or drugs.

 Keep operating area clear of all persons.

WARNING! Risk of injury or injection

to persons  Do not discharge

stream at persons or animals.

 High pressure hose can develop leaks from wear,

kinking, abuse, etc. Water spraying from a leak is

capable of injecting material into skin. Do not point

the pressure washer spray at people or animals.

 Do not overreach or stand on unstable support.

Keep good footing and balance at all times.

 Follow the maintenance instructions specified in the

manual.

 This product shall only be connected to a power

supply receptacle protected by a Ground Fault Cir-

cuit Interrupter (GFCI). This is done to comply with

National Electrical Code (NFPA 70) and to provide

additional protection from risk of electrical shock.

 Save these instructions.

 Operate this pressure washer only in areas away

from combustible materials, combustible fumes or

dust.

 Some chemicals or detergents may be harmful if

inhaled or ingested, causing severe nausea, faint-

ing or poisoning. The harmful elements may cause

property damage or severe injury.

 Do not allow CHILDREN to operate the Pressure

Washer at any time.

 Before starting the Pressure Washer in cold

weather, check all parts of the equipment and be

sure ice has not formed.

 Units with broken or missing parts, or without pro-

tective housing or covers should NEVER be

operated.

DANGER! Risk of Explosion  Do

not spray flammable liquids.

 Never aim the gun at people, animals or plants.

 For household use. For indoor or outdoor use.

 High pressure stream of fluid that this equipment

can produce may pierce skin and its underlying tis-

sues, leading to serious injury and possible

amputation.

 High pressure spray can cause paint chips or other

particles to become airborne and fly at high speeds.

 Always wear eye protection when you use this

equipment or when you are in vicinity where the

equipment is in use.

High Pressure Washer

GENERAC

Generac 1300PSI Electric High Pressure Washer

Save these instructions

IMPORTANT!  SAFETY INSTRUCTIONS  IMPORTANT!

High Pressure Washer

GENERAC

Generac 1300PSI Electric High Pressure Washer

 Never move the machine by pulling on high pres-

sure hose. Use the handle provided on the top of

the unit.

 Use a respirator or mask whenever there is a

chance that vapors may be inhaled. Read all

instructions with the mask so you are certain the

mask will provide the necessary protection against

inhaling harmful vapors.

 High pressure spray may damage fragile items

including glass. Do not point spray gun at glass

when in the high pressure mode.

 Keep the hose connected to machine or the spray

gun while the system is pressurized. Disconnecting

the hose while the unit is pressurized is dangerous.

 Hold the spray gun firmly in your hand before you

start the unit. Do not leave the pressure washer

unattended while the machine is turned on.

 Cleaning area should have adequate slopes and

drainage to reduce possibility of a fall due to slip-

pery surfaces.

 Keep water spray away from electric wiring or fatal

electric shock may result.

 Do not by-pass any safety device on this machine.

 Operate and store this unit on a stable surface.

 Inspect hose each time before using it. Check all

hoses for cuts, leaks, abrasions, bulging of cover,

damage or movement of couplings. If any of these

conditions exist, replace hose immediately. Never

repair high pressure hose. Replace it with another

hose that meets minimum pressure rating of your

pressure washer.

 Store in a clean, dry area. Ideally, the unit should be

stored in a frost-free room.

Servicing of a Double Insulated Product.

In a double-insulated product, two systems of insula-

tion are provided instead of grounding. No means of

grounding is provided on a double-insulated product,

nor should a means for grounding be added.

Servicing a double-insulated product requires extreme

care and knowledge of the system and should be

done only by qualified service personnel. Replace-

ment parts for a double-insulated product must be

identical to the parts they replace. Use only genuine

replacement parts. A double-insulated product is

marked with the words DOUBLE INSULATION or

DOUBLE INSULATED.

The symbol may also be marked on the product.

Extension Cords

Use only extension cords that are approved for out-

side use. These extension cords are identified by a

marking ACCEPTABLE FOR USE WITH OUTDOOR

APPLIANCES; STORE INDOORS WHILE NOT IN

USE. Use only extension cords having an electrical

rating greater than the rating of the product. Do not

use damaged extension cords. Examine extension

cord before using and replace if damaged. Do not

abuse extension cord and do not yank on any cord to

disconnect it. Keep cord away from heat and sharp

edges. Always disconnect the extension cord from the

receptacle before disconnecting the pressure washer

from the extension cord.

Save these instructions

IMPORTANT!  SAFETY INSTRUCTIONS  IMPORTANT!

High Pressure Washer

CONGRATULATIONS on your purchase of a

GENERAC electric high pressure washer. It has been

designed, engineered and manufactured to give you

the best possible dependability and performance.

Should you experience any problem you cannot easily

remedy, please contact your nearest GENERAC

Authorized Service facility, or call the

18002701408 number listed on the front of this

manual. We have competent, well-trained technicians

and the proper tools to service or repair this unit.

Please read and retain this manual. The instructions

will enable you to assemble and maintain your high

pressure washer properly. Always observe the

SAFETY RULES.

CUSTOMER RESPONSIBILITIES

 Read and observe the safety rules.

 Follow regular schedule in maintaining, caring for

and using your high pressure washer.

 Follow the instructions under Maintenance and

Storage sections of this Owner's Manual.

PRODUCT SPECIFICATIONS

Pressure Washer Specifications

Pressure 1300 pounds per square inch

(PSI)

Flow Rate 1.5 gallons per minute (GPM)

Detergent Mix Use Undiluted Detergent

Water Supply Inlet water not to exceed

Temperature 104°F

Motor Brush Type (Universal)

Rated Voltage 120 Volts

Current 14 Amperes

Read these instructions and Operators Manual in its

entirety before you attempt to assemble or operate

your new high pressure washer. Your high pressure

washer has, for the most part, been assembled at the

factory. Before you can operate your new high pres-

sure washer, you must properly connect the high

pressure hose and the water supply.

If you have any problems with the assembly of your

pressure washer, please call the pressure washer

helpline at 1-800-270-1408.

GENERAC

Generac 1300PSI Electric High Pressure Washer

Model

Number 07762

Serial

Number_________________________________

Date of

Purchase________________________________

The model and serial numbers will be found on a

decal attached to the pressure washer. You

should record both serial number and date of pur-

chase and keep in a safe place for future

reference

GENERAC

Generac 1300PSI High Pressure Washer

High Pressure Washer

Spray Gun  Controls the application of water onto

cleaning surface with trigger device. Includes safety

latch.

High Pressure Outlet  Connection for high pres-

sure hose.

Master On/Off Switch  This switch ONLY enables

the Grip Start system to function.

Grip Start System  Pressing and releasing the

spray gun trigger starts and stops the electric motor in

the pressure washer.

Safety Flow System  Electric motor will not start

unless water is supplied to the pump.

Foamer  Used to apply detergent. Mixes water

and detergent in outlet water flow.

Bayonet Adapter (Not Shown)  Connector accom-

modates the connection of a utility and rotating brush

to the spray gun.

Water Inlet  Connection for garden hose. (Note:

You need to use the quickconnect to attach the

garden hose to the pressure washer)

Adjustable Nozzle Extension  Turn nozzle clock-

wise for narrow spray and counterclockwise for fan

spray.

High Pressure Hose  Connect ends to spray gun

and high pressure outlet.

Goggles  Always wear eye protection when operat-

ing your pressure washer.

QuickConnect  Allows rapid connection of your

garden hose to the water inlet.

Read this owners manual before operating your high pressure washer. Compare the illustrations with your

high pressure washer to familiarize yourself with the locations of various controls and adjustments. Save this

manual for future reference.

Spray Gun

Master On/Off Switch

High Pressure Outlet

High Pressure Hose

Adjustable Nozzle

Extension

Water Inlet

Grip Start System

Safety Flow System

Quick Connect

Foamer

Goggles

High Pressure Washer

GENERAC

Generac 1300PSI Electric High Pressure Washer

CARTON CONTENTS

Items in the carton include:

 Main Unit

 Parts Box (which includes the following):

 Goggles

 Owners Manual

 Spray Gun

 Adjustable Nozzle Extension

 Foamer

 High Pressure Hose

 Parts Bag (which includes the following):

 Nozzle Cleaning Kit

 Bayonet adapter, must be used to attach the

brushes to the gun.

 Quick Connect (male and female ends)

Refer to the above list for an illustrated listing of all

items included with your pressure washer. Become

familiar with each piece before assembling the pres-

sure washer. Check all contents against list. If any

parts are missing, call the pressure washer helpline at

1-800-270-1408.

HOW TO SET UP YOUR PRES-

SURE WASHER

 Follow the instructions in the cart box to assemble

the cart and install it onto the main unit.

 Unwind the high pressure hose and attach it to

spray gun (Figure 1).

 Attach the high pressure hose to the high pressure

outlet and tighten by hand (Figure 2).

 Included with this unit is a quick-connect fitting that

you must attach to the water inlet and your garden

hose. You can install the grey male connector by

hand but you may need to use an adjustable

wrench to tighten it (Figure 3).

 Check the screen on the female connector. Make

sure it is clean and check for damage. If you see

any damage in the screen, do not use that female

connector.

 Attach the female quick connect to your garden

hose.

 Attach garden hose to the water inlet using the

quickconnect. The quickconnect should lock in

place. (Figure 4 on page 7).

AASSSSEEMMBBLLYY

Figure 1 — Attach High Pressure Hose to Spray

Gun.

Figure 2 — Attach High Pressure Hose to Main

Unit.

Figure 3 — Install Quick–Connect.

Connect high pressure

hose here

Male QuickConnect

Female QuickConnect

Generac 1300PSI Electric High Pressure Washer

High Pressure Washer

GENERAC

DANGER: When connecting the unit to a

power supply receptacle, use ONLY a

receptacle protected by a Ground Fault Cir-

cuit Interrupter (GFCI). This will help

protect against electrical shock.

CAUTION: Before starting you should be

sure the electrical supply is rated at 120

volts, 15 amps.

WARNING: To reduce the risk of electrocu-

tion, keep ALL connections dry and off the

ground. DO NOT touch plug with wet

hands.

 We do not recommend that you use extension

cords with this pressure washer. If, however, your

application requires that you need an extension

cord, use only extension cords that are approved for

outside use. These extension cords are identified by

a marking ACCEPTABLE FOR USE WITH OUT-

DOOR APPLIANCES; STORE INDOORS WHILE

NOT IN USE. Use only extension cords having an

electrical rating not less than the rating of the prod-

uct. Do not use damaged extension cords.

 Turn on the water.

NOTE: Inlet water temperature should not exceed

104°F.

DANGER: You must attach the spray gun

and all hoses before you start the motor.

DANGER: You must be careful at this point.

Anytime you squeeze the trigger, the motor

will start and water will spray out of the

gun.

 Squeeze trigger to purge pump of system air and

impurities.

 Attach the adjustable nozzle extension to spray gun

by aligning the locking tabs on the extension with

the grooves in the gun. Push extension inward and

twist clockwise to lock in place (Figure 5).

 Press the master On/Off Switch to the On position

(Figure 6).

CAUTION: Before starting the pressure

washer, be sure you are wearing adequate

eye protection. Goggles are included with

this unit.

WARNING: Gun kicks back. Use both

hands.

DANGER: Risk of injury or injection to

people and animals. DO NOT discharge

stream at people or animals.

AASSSSEEMMBBLLYY

Figure 4 — Connect Garden Hose to Water

Inlet Opening.

Figure 6 — Press the Master On/Off Switch to

the “On” Position.

Figure 5 — Connect the Adjustable Nozzle

Extension to the Spray Gun.

High Pressure Washer

GENERAC

Generac 1300PSI Electric High Pressure Washer

 Squeeze trigger to produce spray.

NOTE: Behind the trigger to the gun is a SAFETY

LATCH. You can place this latch as shown in Figure 7

to keep the washer from accidentally spraying while

you are changing the nozzle head or foamer or per-

forming other tasks.

STOPPING YOUR PRESSURE

WASHER

 If the pressure washer is running, release the trig-

ger.

DANGER: Releasing the trigger will shut

off the motor but does not shut off the

unit. You must also place the Master

On/Off Switch to the OFF position.

 Place Master On/Off switch in Off position.

Simply shutting OFF motor will not release pres-

sure in the system. Squeeze the trigger on the gun

to relieve the pressure in the hose.

DANGER: Never leave your pressure

washer unattended even when turned off.

HOW TO USE YOUR WASHER

You now should know how to START your pressure

washer and how to STOP it. The information in this

section will tell you how to adjust the spray pattern

and apply detergent or any other cleaning chemicals.

HOW TO USE ADJUSTABLE NOZZLE

DANGER: Never adjust spray pattern when

spraying. Never put hands in front of spray

nozzle to adjust spray pattern. You could

be injured.

On the end of your spray gun is a nozzle that you can

twist from side to side. With the adjustable nozzle you

can adjust the spray configuration to be either concen-

trated in a stream or expanded into a fan pattern.

 Twist nozzle counterclockwise when you wish to

produce an expanded stream. Twist nozzle clock-

wise to produce a narrow, concentrated stream

(Figure 8).

Figure 7 — Apply the Safety Latch.

Figure 8 — Using the Adjustable Nozzle.

Twist Nozzle

Counterclockwise

for Fan Spray

Twist Nozzle

Clockwise for

Narrow Spray.

High Pressure Washer

GENERAC

Generac 1300PSI Electric High Pressure Washer

 Point the nozzle toward the ground and press the

trigger to test the pattern.

 For most effective cleaning, keep spray nozzle

between 8 to 24 inches of cleaning surface.

 If you get the spray nozzle too close, especially

using high pressure mode, you may damage the

cleaning surface.

 Do not get closer than 6 inches when cleaning auto-

mobile tires.

Applying Detergent With Foamer

IMPORTANT: Use soaps designed specifically for

pressure washers. Household detergents could

damage the pump.

NOTE: Never use garden hose inlet to siphon deter-

gent or wax.

DANGER: You MUST attach all hoses and the spray

gun before you start the motor.

WARNING: Before removing any spray gun

extension, be sure to turn off the pressure

washer and relieve pressure by pressing

the trigger. You could be injured if you try

to remove an extension if the pressure

washer is running and there is pressure in

the system.

Pressure washers are useful cleaning tools designed

to clean almost any surface in two easy steps.

 The first step involves applying an appropriate

detergent/solvent solution to penetrate and loosen

grime. The detergent is applied at low pressure

to avoid splashing, overspraying and waste.

Leave the solution on surface for 3 to 5 minutes to

allow solution to work.

 The second step involves cleaning the surface you

have prepared with the pressure washer and then

rinsing it clean.

To apply detergent follow these steps:

 Detach the nozzle extension by pushing in and

unlocking it counterclockwise.

 Remove the bottle from the foamer.

 Align the locking tabs on the foamer with the groves

in the gun. Push inward and twist clockwise to lock

in place. (Note: make sure that the when you lock

the foamer into place you have the hose that con-

nects to the foamer bottle hanging downward.)

 Prepare your detergent solution as required by your

job and fill bottle with the solution.

 Attach bottle back onto foamer making sure the

bottle hangs down.

 Start washer and apply detergent to a dry surface,

starting from the bottom and working up.

 To rinse, YOU MUST, stop the pressure washer,

remove the foamer and connect the adjustable

nozzle extension.

NOTE: Detergents are most effective applied to a dry

surface.

To Clean

Start at lower portion of area to be washed and work

upward, using long, even overlapping strokes. Deter-

gent or degreaser works best when you apply it to a

dry surface first. Let it set for 3-5 minutes before

washing and rinsing.

Rinse

Start at the top of area to be rinsed, working down

with the same action as for cleaning.

Figure 9  Connecting the Foamer.

GENERAC

Generac 1300PSI Electric High Pressure Washer

High Pressure Washer

CUSTOMER RESPONSIBILITIES

AND MAINTENANCE

The warranty of the high pressure washer does not

cover items that have been subjected to operator

abuse or negligence. To receive full value from the

warranty, operator must maintain high pressure

washer as instructed in this manual.

BEFORE EACH USE

Check and Clean Quick-Connect

Screen

Remove quick-connect and examine the inlet screen

on the female connector. Clean if clogged or replace

the quick-connect inlet screen if damaged.

Check High Pressure Hose

DANGER: Water spraying from a leak is

capable of injecting material into skin.

Inspect hose each time before using it.

Never repair high pressure hose. Replace it

with another hose that meets minimum

pressure rating of your pressure washer.

High pressure hose can develop leaks from wear,

kinking, and abuse. Check all hoses for cuts, leaks,

abrasions or bulging of cover, or damage or move-

ment of couplings. If any of these conditions exist,

replace hose immediately.

Check Gun and Wand

Examine hose connection and make sure it is secure.

Test trigger by pressing it and making sure it springs

back into place when released. Put safety latch in ON

position and test trigger. You should not be able to

press trigger.

PURGE PUMP OF AIR AND

CONTAMINANTS

To remove the air from the pump, follow these

steps:

 Set up the pressure washer as described in the

ASSEMBLY section and connect the water supply.

 Remove the nozzle lance from the gun.

 Pull the trigger on the gun and hold.

To remove the contaminant from the pump, follow

these steps:

 Set up the pressure washer as described in the

ASSEMBLY section, connect the water supply and

start the pressure washer according to instructions

in the OPERATION section.

 Remove the nozzle lance from the gun.

 Pull the trigger on the gun and hold.

 When the water supply is steady and constant, you

may refasten the nozzle attachment and start the

pump.

NOZZLE MAINTENANCE

If the nozzle becomes restricted or clogged with for-

eign materials, such as dirt, excessive pump pressure

may develop. A partially clogged nozzle can cause a

pulsing sensation during use. This generally is not a

pump related problem, but rather a clogged or par-

tially restricted nozzle.

If the nozzle becomes clogged or partially restricted,

immediately clean the nozzle with the kit included with

your pressure washer by following these instructions:

 Shut off the washer and turn off the water supply.

 Separate the nozzle extension from the gun.

 Open the adjustable nozzle to the narrow stream

setting.

 Remove the nozzle using the allen wrench provided

in the kit.

 Use the wire included in the kit (Figure 10) or a

small paper clip to free the foreign materials clog-

ging or restricting the nozzle.

 Remove additional debris by back flushing water

supply through wand (Figure 11). Back flush

between 30 to 60 seconds. Turn wand to stream

spray while flushing.

 Reinstall the nozzle. Do not overtighten.

 Reconnect the wand to the gun.

 Reconnect the water supply, turn on the water, and

start the washer.

 Test the pressure washer by operating with nozzle

in narrow and expanded streams.

PREPARING THE UNIT FOR

STORAGE

Water should not remain in the unit for long periods of

time. Sediments of minerals can deposit on pump

parts and freeze pump action. If you do not plan to

use the Pressure Washer for more than 30 days,

follow this procedure:

1. Shut off the pressure washer, unplug it and let it

cool, then remove all hoses.

2. Store the pressure washer and its components in

such a way as to protect it from freezing.

5. Store in a clean, dry area. Ideally, the unit should

be stored in a frost-free room.

6. Coil the high pressure hose and inspect it for

damage. Cuts in the hose or fraying of it could result

in leaks and loss of pressure. Should any damage be

found, replace the hose. DO NOT attempt to repair a

damaged hose. Replace the hose with the genuine

Generac part.

7. Drain water from hose and properly store it to pre-

vent cuts and general wear.

Figure 11 — Backwashing the Nozzle.

Generac 1300PSI Electric High Pressure Washer

High Pressure Washer

GENERAC

Figure 10 — Loosening Debris in Nozzle.

High Pressure Washer

GENERAC

Generac 1300PSI Electric High Pressure Washer

TROUBLESHOOTING POINTS

Problem Cause Correction

Pressure washer will not start. 1. No electrical power is available. 1. Check cord, plug power, socket,

electrical supply and circuit

breaker/fuse.

2. Motor overheats. 2. Turn off the unit. Press trigger of

gun to relieve.pressure on the

unit. Allow unit to cool for about 2

min. It should run when you turn it

ON again.

3. Low voltage. 3. Contact Generac service facility.

4. Trigger not open. 4. Open trigger.

5. Electrical defect. 5. Contact Generac service facility.

Pressure washer does not 1. Pump is sucking air. 1. Water hose must be 1/2-inch

come up to pressure. or greater in diameter.

Be sure water supply is ON.

Be sure water supply is clean.

Check all connections for leaks

or blockage.

Turn OFF the unit, hold trigger in

OPEN position to relieve pressure

and allow air in line to escape.

With trigger still in OPEN position

turn ON the unit. Repeat if

necessary.

2. Water inlet is clogged. 2. Clean water inlet screen.

3. Pump not bled to remove air. 3. Switch OFF washer, press trigger,

switch ON washer while pressing

trigger. Repeat if necessary.

4. Pump is faulty. 4. Contact Generac service facility.

High pressure spray is irregular. 1. Nozzle or water supply is restricted. 1. Unplug unit and clean nozzle.

2. Water supply is inadequate. 2. Turn ON water to full position.

NOTES

High Pressure Washer

GENERAC

Generac 1300PSI Electric High Pressure Washer

Drawing No. B2452

High Pressure Washer

GENERAC

Generac 1300PSI Electric High Pressure Washer

EXPLODED VIEW  PUMP AND MOTOR

Drawing No. B2542

High Pressure Washer

GENERAC

Generac 1300PSI Electric High Pressure Washer

PARTS LIST  PUMP AND MOTOR

Item Part # Qty. Description Item Part # Qty. Description

1 B1514 1 ASSY, Motor Complete

2 97100 1 CAP, HP

3 21054 1 BOOT, Rubber

4 21055 1 GROMMET, Rubber

5 20138 1 SWITCH, Auto

6 20928 1 HOUSING, Auto-Switch

7 20218 1 CAP, Retainer

8 B2733 1 PISTON ASSY, Auto Switch

9 21525 2 WIPER, Piston Bore

10 B1124 1 CAP, Inlet

11 97855 1 O RING, dia. 6.5 x 2.01mm

12 97934 3 O RING, Chk Valve dia. 12.4 x

.78mm

13 20212 1 SPRING, 15.08 x dia. 1.62 CS x

22.3

14 B1960 1 SEAT, Ball

15 B2240 1 SCREW, Lock Socket

16 A1495 2 TAPTITE, M4-0.7x10mm SW

MTG

19 21124 1 RING, Backup dia. 4.34 Id x 1.24

20 21123 1 O RING dia. 3.68 Id x 1.78 CS

[.070"]

21 21126 1 RING, Backup dia. 26.0 ID

22 21125 1 O RING dia. 25.07 ID x 2.62 CS

[.103"]

23 20217 1 STOP, Piston Return

24 A1130 1 SPRING, Pop-off Valve

26 97852 1 BALL, dia. 3/16" Pop-off Valve

29 28739A 1 TIE, Wrap

31 97840 3 O RING,

Hi-press dia. 15.6 x

1.78mm

3297841 3 CAP, Check Valve

33 97837 1 O RING, Hi-press dia. 9.2 x

2.62mm

34 97835 1 O RING, Hsg Seal, dia. 82.2 x

2.62mm

36 76353A 1 PLUG, Taper dia. 5.4

37 B2664 3 ASSY., Check Valve, Inlet

38 A1111A 1 PUMP, Head

39 97839 3 ASSY., Check Valve, Outlet

40 97851 3 O RING, Piston dia. 10.82 x

1.78mm

41 97832 3 PISTON dia. 15 x 65mm

42 40946 4 BOLT, SHCS M6- 1.0 x 35mm

43 93873 4 LOCKWASHER, M6 Ribbed

44 93667 3 SEAL, Piston U Cup

45 97831 3 SPACER, Pilot

46 93680 3 SEAL, Oil-piston dia. 15 TC4

47 B1119 1 HOUSING, Piston

48 99503 3 SPRING, Piston Return

49 40945 3 RETAINER, Piston Spring

50 97962 3 BOLT, SHCS M6-1.0 x 20mm

51 97824A 1 BEARING, Needle dia. 40 x

60mm

52 97826 1 WASHER, Brg dia. 40 x 60 x

1mm

53 97825 1 WASHER, Brg dia. 36 x 60 x

6mm

55 B2663 1 ASSY., Cam/Gear

56 97822 1 BEARING,

Ndle Thrust dia. 35 x

52mm

57 20610 2 WASHER, Brg dia. 35 x 55 x

3mm

60 97833 1 SHAFT, Idler Axial Cam

Drawing No. B2491

EXPLODED VIEW  XXXXXX...

High Pressure Washer

GENERAC

Generac 1300PSI Electric High Pressure Washer

EXPLODED VIEW  MAIN UNIT

Drawing No. B2491

GENERAC

EXPLODED VIEW  XXXXXX...

High Pressure Washer

Generac 1300PSI Electric High Pressure Washer

PARTS LIST  MAIN UNIT

ITEM PART NO. QTY. DESCRIPTION

1 N/A 1 ASSY., Motor and Pump (see exp. view B2452)

2 B1415 1 DECAL, Circuit

3 A1252 1 DECAL, Unit

4 A1313 1 DECAL, Instructions

5 20566 1 DECAL, 1-800 #

6 98806 1 FOAM, Air In, Fan-end

7 97893 1 HOUSING, Switch and Cord

8 20984 1 SWITCH, Rocker 16A

9 98801 4 MOUNT, Rubber

10 97892 1 COVER, Motor

11 20985 1 ENCLOSURE, Rocker Switch Boot

12 20986 1 BOOT, Rocker Switch

13 84543B 2 SCREW, 3.5mm x 12mm Plastite

14 98805 1 CORD, Power

15 84358 4 SCREW, #6-19 x .75 mm Plastite

16 99349 1 STRAIN RELIEF, Cord

17 B1053 1 DECAL, ETL

18 B2492 1 DECAL, Data

19 99736 1 OVERLAMINATE

20 21334 1 HOUSING, Inlet

21 21335 1 HOUSING, Outlet

22 21265 1 QUICK DISCONNECT, Male

23 96016 1 QUICK DISCONNECT, Female

24 A1484 1 NUT, Strain Relief Lock

25 A1485 1 SEAL RING, Strain Relief

26 97835 1 O RING, Hsg Seal, dia. 82.2 x 2.62mm

27 99350 6 SCREW, #6 Plastite

28 21336 1 GUN, Spray

29 21337 1 WAND, Extension

30 B1417 1 HOSE, High Pressure

31 21338D 1 NOZZLE, Head

32 A1069 1 FOAMER

33 B1051 1 ADAPTOR, Accessories

34 87815 1 GOGGLES

35 98904 1 HANG TAG CSA, Nozzle

36 B1236D 1 NOZZLE, 1.15mm dia. (Lilac)

NOTES

High Pressure Washer

GENERAC

Generac 1300PSI Electric High Pressure Washer

NOTES

High Pressure Washer

GENERAC

Generac 1300PSI Electric High Pressure Washer

LIMITED PRESSURE WASHER WARRANTIES

(includes Master Contractor)

GENERAC warrants to the original retail purchaser, the pressure washer manufactured by GENERAC to be

free from defects in material and workmanship for the period(s) set forth below from the date of original pur-

chase. This warranty is not transferable. The term original purchaser means the person for whom the

pressure washer is originally purchased.

Warranty Schedules

Electric Power Washer 1 year (does not apply to commercial or rental operations)

CONSUMER* COMMERCIAL*

Generac GN-Series Engine-driven Engine: 2 years 1 year

Power Washer (2nd year parts only)

Pump: 1 year 90 days

All Other Engine-driven Engine: Warranted solely by Warranted solely by

Power Washers Engine Manufacturer Engine Manufacturer

Pump: 1 year 90 days

* NOTE: For the purpose of this warranty Consumer Use means personal residential household use

by original purchaser. Commercial Use means all other uses, including rental, construction, com-

mercial and income producing purposes. Once a pressure washer has experienced commercial use, it

shall thereafter be considered a commercial use pressure washer for the purposes of this warranty.

During said warranty period, GENERAC will, at its option, repair or replace any part which, upon examination

by GENERAC or GENERAC Authorized Dealers, is found to be defective under normal use and service**. All

transportation costs under warranty, including return to the factory if necessary, are to be borne by the pur-

chaser and prepaid by the purchaser.

** NORMAL WEAR: As with all mechanical devices, the GN-Series engines need periodic parts ser-

vice and replacement to perform well. This warranty will not cover repair when normal use has

exhausted the life of a part or an engine.

THIS WARRANTY DOES NOT INCLUDE: Used products and demonstration equipment. Parts such as

GUNS, HOSES, WANDS, NOZZLES or other wear items such as quick couplers, oil, gauges, belts, O-rings,

filters, pump packing, etc. Pumps which have been run without water supplied. Damage or malfunctions

resulting from: accidents, abuse, modifications, alterations, or improper servicing. Freezing or chemical dete-

rioration. Normal maintenance such as adjustments, fuel system cleaning and obstruction (due to chemical,

dirt, carbon or lime, etc.).

THIS WARRANTY IS IN PLACE OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, SPECIFICALLY,

GENERAC MAKES NO OTHER WARRANTIES AS TO MERCHANTABILITY OR FITNESS FOR A PARTICU-

LAR PURPOSE. The duration of any implied warranties which cannot be disclaimed is limited to the time

period as specified in the express warranty. LIABILITY FOR CONSEQUENTIAL, INCIDENTAL, OR SPECIAL

DAMAGES UNDER ANY AND ALL WARRANTIES IS EXCLUDED, EVEN IF SUCH DAMAGES ARE A

DIRECT RESULT OF GENERACs NEGLIGENCE. Some states do not allow limitations on how long an

implied warranty lasts, or the exclusion or limitation of incidental or consequential damages, so the above limi-

tations or exclusions may not apply to you. This warranty gives you specific legal rights and you may also

have other rights, which vary from state to state.

For service, see your nearest GENERAC authorized warranty service facility or call 1-800-333-1322. War-

ranty service can be performed only by a GENERAC authorized service facility. This warranty will not apply to

service at any other facility. At the time of requesting warranty service, evidence of original purchase date

must be presented.

GENERAC CORPORATION

GENERAC

Generac 1300PSI Electric High Pressure Washer

Simplicity 00776-2 User manual

Brand: Simplicity

Model: 00776-2

Category: High-pressure cleaners

Type: User manual

Download PDF

report

Simplicity 00776-2 User manual

Simplicity 00776-2 User manual

Related papers

Other documents