1300PSI
Double Insulated
Electric High Pressure Washer
Owners Manual
This symbol points out important safety instructions, which, if not followed, could endanger the personal safety
and/or property of yourself and others. Read and follow all instructions in thE manual before attempting to operate
this unit.
Model No. 0776-1 (1.5 gpm High Pressure Washer) Manual No. B1742 Revision 0 (7/17/97)
PRESSURE WASHER
CUSTOMER HELPLINE
1-800-270-1408
HOURS: Mon.-Fri. 8 a.m. to 5 p.m.
(CST)
GENERAC
The Reliable Ones
DANGER!
Risk of electrocution!
Inspect cord before every use. Do not use if cord is damaged.
Keep all connections dry and off the ground.
Do not touch plug with wet hands.
Double-insulated When servicing, use only identical replacement parts.
This product shall only be connected to a power supply receptacle protected by
a Ground Fault Circuit Interrupter (GFCI).
Read instruction manual before using.
CAUTION!
When using this product, basic precautions should always be fol-
lowed, including the following:
To reduce the risk of injury, read all instructions before using the product.
WARNING!
To reduce the risk of injury, close supervision is necessary when
product is used near children.
Know how to stop the product and bleed the pressure quickly. Be thoroughly famil-
iar with controls.
Stay alert. Watch what you are doing.
Do not operate the product when fatigued or under the influence of alcohol or drugs.
Keep operating area clear of all persons.
WARNING!
Risk of injury or injection to persons Do not discharge stream at per-
sons or animals.
High pressure hose can develop leaks from wear, kinking, abuse, etc. Water
spraying from a leak is capable of injecting material into skin. Do not point the
pressure washer spray at people or animals.
Do not overreach or stand on unstable support. Keep good footing and balance
at all times.
Follow the maintenance instructions specified in the manual.
This product shall only be connected to a power supply receptacle protected by
a Ground Fault Circuit Interrupter (GFCI). This is done to comply with National
Electrical Code (NFPA 70) and to provide additional protection from risk of elec-
trical shock.
Save these instructions.
Operate this pressure washer only in areas away from combustible materials, com-
bustible fumes or dust.
Some chemicals or detergents may be harmful if inhaled or ingested, causing severe
nausea, fainting or poisoning. The harmful elements may cause property damage
or severe injury.
Do not allow CHILDREN to operate the Pressure Washer at any time.
Before starting the Pressure Washer in cold weather, check all parts of the equip-
ment and be sure ice has not formed.
Units with broken or missing parts, or without protective housing or covers should
NEVER be operated.
DANGER!
Risk of Explosion Do not spray flammable liquids.
Never aim the gun at people, animals or plants.
For household use. For indoor or outdoor use.
High pressure stream of fluid that this equipment can produce may pierce skin
and its underlying tissues, leading to serious injury and possible amputation.
High pressure spray can cause paint chips or other particles to become airborne
and fly at high speeds.
Always wear eye protection when you use this equipment or when you are in vicin-
ity where the equipment is in use.
Never move the machine by pulling on high pressure hose. Use the handle pro-
vided on the top of the unit.
Use a respirator or mask whenever there is a chance that vapors may be inhaled.
Read all instructions with the mask so you are certain the mask will provide the
necessary protection against inhaling harmful vapors.
High pressure spray may damage fragile items including glass. Do not point spray
gun at glass when in the high pressure mode.
Keep the hose connected to machine or the spray gun while the system is pres-
surized. Disconnecting the hose while the unit is pressurized is dangerous.
Hold the spray gun firmly in your hand before you start the unit. Do not leave the
pressure washer unattended while the machine is turned on.
Cleaning area should have adequate slopes and drainage to reduce possibility
of a fall due to slippery surfaces.
Keep water spray away from electric wiring or fatal electric shock may result.
Do not by-pass any safety device on this machine.
Operate and store this unit on a stable surface.
Inspect hose each time before using it. Check all hoses for cuts, leaks, abrasions,
bulging of cover, damage or movement of couplings. If any of these conditions
exist, replace hose immediately. Never repair high pressure hose. Replace it with
another hose that meets minimum pressure rating of your pressure washer.
Store in a clean, dry area. Ideally, the unit should be stored in a frost-free room.
SERVICING OF A DOUBLE-INSULATED PRODUCT
In a double-insulated product, two systems of insulation are provided instead of
grounding. No means of grounding is provided on a double-insulated product, nor
should a means for grounding be added.
Servicing a double-insulated product requires extreme care and knowledge of the
system and should be done only by qualified service personnel. Replacement parts
for a double-insulated product must be identical to the parts they replace. use only
genuine replacement parts. A double-insulated product is marked with the words
DOUBLE INSULATION or DOUBLE INSULATED.
The symbol may also be marked on the product.
EXTENSION CORDS
Use only extension cords that are approved for outside use. These extension cords
are identified by a marking ACCEPTABLE FOR USE WITH OUTDOOR APPLI-
ANCES; STORE INDOORS WHILE NOT IN USE. Use only extension cords having
an electrical rating not less than the rating of the product. Do not use damaged exten-
sion cords. Examine extension cord before using and replace if damaged. Do not
abuse extension cord and do not yank on any cord to disconnect it. Keep cord away
from heat and sharp edges. Always disconnect the extension cord from the recep-
tacle before disconnecting the pressure washer from the extension cord.
2
GENERAC
Generac 1300PSI Electric High Pressure Washer
Save these instructions
IMPORTANT! SAFETY INSTRUCTIONS IMPORTANT!
3
GENERAC
Generac 1300PSI Electric High Pressure Washer
CONGRATULATIONS on your purchase of a GENERAC
electric high pressure washer. It has been designed, engi-
neered and manufactured to give you the best possible
dependability and performance.
Should you experience any problem you cannot easily
remedy, please contact your nearest GENERAC Authorized
Service facility, or call the 18002701408 number listed
on the front of this manual. We have competent, well-
trained technicians and the proper tools to service or repair
this unit.
Please read and retain this manual. The instructions will
enable you to assemble and maintain your high pressure
washer properly. Always observe the SAFETY RULES.
CUSTOMER RESPONSIBILITIES
Read and observe the safety rules.
Follow regular schedule in maintaining, caring for and using
your high pressure washer.
Follow the instructions under Maintenance and Storage
sections of this Owner's Manual.
PRODUCT SPECIFICATIONS
PRESSURE WASHER SPECIFICATIONS
Model
Number 0776-1
Serial
Number_________________________________
Date of
Purchase________________________________
The model and serial numbers will be found on a decal
attached to the pressure washer. You should record both
serial number and date of purchase and keep in a safe place
for future reference
Pressure 1300 psi
Flow Rate 1.5 GPM
Detergent Mix Use undiluted detergent
Water Supply Cold water not to
Temperature exceed 104°F
Motor Brush type (universal)
Rated Voltage 120 volts
Current 14 amperes
4
GENERAC
Generac 1300PSI Electric High Pressure Washer
CONTENTS OF PACKAGE
High Pressure Washer
High Pressure Hose*
Nozzle Extension*
Foamer*
* These parts are found separately in the parts box within the package.
** These parts are found separately in the parts bag within the parts box.
Goggles*
Spray Gun*
Nozzle Cleaning Kit**
Quick-Connect**
Accessories
Adapter**
PACKAGE
5
Spray Gun Controls the application of water onto
cleaning surface with trigger device. Includes safety
latch.
High Pressure Outlet Connection for high
pressure hose.
Master On/Off Switch This switch ONLY enables
the Grip Start system to function.
QuickConnect Easy connection for intake water
supply.
Grip Start System Pressing and releasing the
spray gun trigger starts and stops the electric motor
in the pressure washer.
Safety Flow System Electric motor will not start
unless water is supplied to the pump.
Foamer Used to apply detergent. Mixes water and deter-
gent in outlet water flow.
Accessories Adapter (Not Shown) This specially designed
connector accommodates the connection of a multipurpose
and rotating brush to the spray gun. Both brushes are sold
separately and are not included with this unit.
Water Inlet Connection for garden hose. (Note: You need
to use the quickconnect to attach the garden hose to the pres-
sure washer)
Nozzle Extension Attaches to spray gun.
GENERAC
Generac 1300PSI Electric High Pressure Washer
Read this owners manual before operating your high pressure washer. Compare the illustrations with your high pressure
washer to familiarize yourself with the locations of various controls and adjustments. Save this manual for future reference.
Spray Gun
Master On/Off Switch
High Pressure Outlet
Nozzle Extension
Water Inlet
Grip Start System
Safety Flow System
QuickConnect
Foamer
6
GENERAC
Generac 1300PSI Electric High Pressure Washer
Read these instructions and Operators Manual in its
entirety before you attempt to assemble or operate your
new high pressure washer. Your high pressure washer has,
for the most part, been assembled at the factory. Before you
can operate your new high pressure washer, you must
properly connect the high pressure hose and the water
supply.
If you have any problems with the assembly of your pres-
sure washer, please call the pressure washer helpline at
1-800-270-1408.
TO REMOVE PRESSURE WASHER
FROM CARTON
Remove parts box.
Remove parts bag from parts box.
Remove main unit with attached electrical cord.
Refer to Page 4, Contents of Hardware Pack for an illus-
trated listing of all items included with your pressure
washer. Become familiar with each piece before assembling
the pressure washer. Check all contents against the illustra-
tions on Page 4. If any parts are missing, call the pressure
washer helpline at 1-800-270-1408.
HOW TO SET UP YOUR
PRESSURE WASHER
Unwind the high pressure hose and attach it to spray gun
(see Figure 1).
Attach the high pressure hose to the high pressure outlet
and tighten by hand (Figure 2).
Included with this unit is a quick-connect fitting that you must
attach to the water inlet and your garden hose. You can install
the male connector end by hand but you may need to use
an adjustable wrench to tighten it (Figure 3).
Check the screen on the female quickconnect. Be sure it is
clean and check for damage. If you see any damage in the
screen, do not use that female quickconnect.
Attach the female quick connect to your garden hose.
Attach garden hose to the water inlet using the quickcon-
nect. The quickconnect should lock in place. (Figure 4 on
page 7).
AASSSSEEMMBBLLYY
Figure 1 - Attach Hose to Spray Gun
Figure 2 - Attach High Pressure Hose to Main Unit
Figure 3 - Install Quick Connect
7
GENERAC
Generac 1300PSI Electric High Pressure Washer
DANGER: When connecting the unit to a power supply
receptacle, use ONLY a receptacle protected by a
Ground Fault Circuit Interrupter (GFCI). This will help
protect against electrical shock.
CAUTION: Before starting you should be sure the
electrical supply is rated at 120 volts, 15 amps.
WARNING: To reduce the risk of electrocution, keep ALL
connections dry and off the ground. DO NOT touch plug
with wet hands.
We do not recommend that you use extension cords with
this pressure washer. If, however, your application requires
that you need an extension cord, use only extension cords
that are approved for outside use. These extension cords
are identified by a marking ACCEPTABLE FOR USE WITH
OUTDOOR APPLIANCES; STORE INDOORS WHILE NOT
IN USE. Use only extension cords having an electrical
rating not less than the rating of the product. Do not use
damaged extension cords.
Turn on the water.
NOTE: Water temperature should not exceed 104°F.
DANGER: You must attach the spray gun all hoses
before you start the motor.
Press the master On/Off Switch to the On position (Figure 5).
DANGER: You must be careful at this point. Anytime you
squeeze the trigger, the motor will start and water will
spray out of the gun.
CAUTION: Before starting the pressure washer, be sure
you are wearing adequate eye protection. Goggles are
included with this unit.
WARNING: Gun kicks back. Use both hands.
DANGER: Risk of injury or injection to people and
animals. DO NOT discharge stream at people or
animals.
Squeeze trigger to purge pump of system air and impurities.
Attach nozzle extension to spray gun by aligning the locking
tabs on the extension with the grooves in the gun. Push exten-
sion inward and twist clockwise to lock in place (Figure 6).
Squeeze trigger to produce spray.
NOTE: Behind the trigger to the gun is a SAFETY LATCH.
You can place this latch as shown in Figure 7 to keep the
washer from accidentally spraying while you are changing
the nozzle head or foamer or performing other tasks.
AA
SSSSEEMMBBLL
YY
Figure 4 - Connect Garden Hose to Water Inlet
Figure 5 - Press the Master ON/OFF Switch to the
ON position.
Figure 6 - Connect the Nozzle Extension to Spray
Gun
Figure 7 - Applying the Safety Latch
8
GENERAC
Generac 1300PSI Electric High Pressure Washer
STOPPING YOUR PRESSURE
WASHER
If the pressure washer is running, release the trigger.
DANGER: Releasing the trigger will shut off the motor
but does not shut off the unit. You must also place the
Master On/Off Switch to the OFF position.
Place Master On/Off switch in OFF position. Simply shutting
OFF motor will not release pressure in the system. Squeeze
the trigger on the gun to relieve the pressure in the hose.
DANGER: Never leave your pressure washer
unattended even when turned off.
HOW TO USE YOUR WASHER
You now should know how to START your pressure washer
and how to STOP it. The information in this section will tell
you how to adjust the spray pattern and apply detergent or
any other cleaning chemicals.
HOW TO USE ADJUSTABLE
NOZZLE
DANGER: Never adjust spray pattern when spraying.
Never put hands in front of spray nozzle to adjust spray
pattern. You could be injured.
On the end of your spray gun is a nozzle that you can twist
from side to side. With the adjustable nozzle you can adjust
the spray configuration to be either concentrated in a stream
or expanded into a fan pattern.
Twist nozzle counterclockwise when you wish to produce an
expanded stream. Twist nozzle clockwise to produce a
narrow, concentrated stream (Figure 8).
Point the nozzle toward the ground and press the trigger to
test the pattern (Figure. 9).
For most effective cleaning, keep spray nozzle between 8 to
24 inches of cleaning surface.
If you get the spray nozzle too close, especially using high pres-
sure mode, you may damage the cleaning surface.
Do not get closer than 6 inches when cleaning automobile tires.
APPLYING DETERGENT WITH
FOAMER
IMPORTANT: Use soaps designed specifically for pressure
washers. Household detergents could damage the pump.
DANGER: You MUST attach all hoses and the spray gun
before you start the motor.
WARNING: Before removing any spray gun extension,
be sure to turn off the pressure washer and relieve
pressure by pressing the trigger. You could be injured if
you try to remove an extension if the pressure washer is
running and there is pressure in the system.
Pressure washers are useful cleaning tools designed to
clean almost any surface in two easy steps.
The first step involves applying an appropriate detergent/sol-
vent solution to penetrate and loosen grime. The detergent
is applied at low pressure to avoid splashing, overspraying
and waste. Leave the solution on surface for 3 to 5 minutes
to allow solution to work.
The second step involves cleaning the surface you have
prepared with the pressure washer and then rinsing it clean.
Twist Nozzle
Counterclockwise
for Fan Spray
Twist Nozzle
Clockwise for
Narrow Spray.
AASSSSEEMMBBLLYY
Figure 8 Using the Adjustable Nozzle
Figure 9 Testing the Spray Pattern
9
GENERAC
Generac 1300PSI Electric High Pressure Washer
To apply detergent follow these steps:
Detach the nozzle extension by pushing in and unlocking it
counterclockwise.
Remove the bottle from the foamer.
Align the locking tabs on the foamer with the groves in the
gun. Push inward and twist clockwise to lock in place. (Note:
make sure that the when you lock the foamer into place you
have the hose that connects to the foamer bottle hanging
downward.)
Prepare your detergent solution as required by your job and
fill bottle with the solution.
Attach bottle back onto foamer making sure the bottle hangs
down.
Start washer and apply detergent to a dry surface, starting
from the bottom and working up.
To rinse, YOU MUST, stop the pressure washer, remove the
foamer and connect the adjustable nozzle extension.
NOTE: Detergents are most effective applied to a dry surface.
TO CLEAN
Start at lower portion of area to be washed and work
upward, using long, even overlapping strokes. Detergent or
degreaser works best when you apply it to a dry surface
first. Let it set for 3-5 minutes before washing and rinsing.
RINSE
Start at the top of area to be rinsed, working down with the
same action as for cleaning.
NOTE: Never use garden hose inlet to siphon detergent or wax.
The warranty of the high pressure washer does not cover
items that have been subjected to operator abuse or negli-
gence. To receive full value from the warranty, operator
must maintain high pressure washer as instructed in this
manual.
BEFORE EACH USE
DANGER: Water spraying from a leak is capable of
injecting material into skin. Inspect hose each time
before using it. Never repair high pressure hose.
Replace it with another hose that meets minimum
pressure rating of your pressure washer.
CHECK AND CLEAN QUICK-
CONNECT SCREEN
Remove quick-connect and examine the inlet screen on the
female connector. Clean if clogged or replace the quick-
connect inlet screen if damaged.
CHECK HIGH PRESSURE HOSE
High pressure hose can develop leaks from wear, kinking,
abuse. Check all hoses for cuts, leaks, abrasions or bulging
of cover, or damage or movement of couplings. If any of
these conditions exist, replace hose immediately.
Figure 10 Connecting the Foamer
10
GENERAC
Generac 1300PSI Electric High Pressure Washer
CHECK GUN AND WAND
Examine hose connection and make sure it is secure. Test
trigger by pressing it and making sure it springs back into
place when released. Put safety latch in ON position and
test trigger. You should not be able to press trigger.
PURGE PUMP OF AIR AND
CONTAMINANTS
To remove the air from the pump, follow these steps:
Set up the pressure washer as described in the ASSEMBLY
section and connect the water supply.
Remove the nozzle attachment from the gun.
Pull the trigger on the gun and hold.
To remove the contaminant from the pump, follow these steps:
Set up the pressure washer as described in the ASSEMBLY
section, connect the water supply and start the pressure
washer according to instructions in the OPERATION sec-
tion.
Remove the nozzle attachment from the gun.
Pull the trigger on the gun and hold.
When the water supply is steady and constant, you may
refasten the nozzle attachment and start the pump.
NOZZLE MAINTENANCE
If the nozzle becomes restricted or clogged with foreign mate-
rials, such as dirt, excessive pump pressure may develop. A
partially clogged nozzle can cause a pulsing sensation during
use. This generally is not a pump related problem, but rather
a clogged or partially restricted nozzle.
If the nozzle becomes clogged or partially restricted, imme-
diately clean the nozzle with the kit included with your pressure
washer by following these instructions:
Shut off the washer and turn off the water supply.
Separate the nozzle extension from the gun.
Open the adjustable nozzle to the narrow stream setting.
Remove the nozzle using the allen wrench provided in the kit.
Use the wire included in the kit (Figure 11) or a small paper
clip to free the foreign materials clogging or restricting the
nozzle.
Figure 11 - Loosening Debris in Nozzle
11
GENERAC
Generac 1300PSI Electric High Pressure Washer
Remove additional debris by back flushing water supply through
wand (Figure 12). Back flush between 30 to 60 seconds. Turn
wand to stream spray while flushing.
Reinstall the nozzle. Do not overtighten.
Reconnect the wand to the gun.
Reconnect the water supply, turn on the water, and start the
washer.
Test the pressure washer by operating with nozzle in narrow
and expanded streams.
PREPARING THE UNIT FOR
STORAGE
Water should not remain in the unit for long periods of time.
Sediments of minerals can deposit on pump parts and freeze
pump action. If you do not plan to use the Pressure Washer
for more than 30 days, follow this procedure:
1.Shut off the pressure washer, unplug it and let it cool, then
remove all hoses.
2. Store the pressure washer and its components in such a way
as to protect it from freezing.
5.Store in a clean, dry area. Ideally, the unit should be stored
in a frost-free room.
6.Coil the high pressure hose and inspect it for damage. Cuts
in the hose or fraying of it could result in leaks and loss of
pressure. Should any damage be found, replace the hose.
DO NOT attempt to repair a damaged hose. Replace the
hose with the genuine Generac part.
7.Drain water from hose and properly store it to prevent cuts
and general wear.
Figure 12 - Backwashing the Nozzle
TROUBLESHOOTING POINTS
12
GENERAC
Generac 1300PSI Electric High Pressure Washer
PROBLEM CAUSE CORRECTION
Pressure washer will not start. 1.No electrical power is available. 1. Check cord, plug power, socket.
and fuse.
2.Motor overheats. 2. Turn off the unit. Press trigger of
gun to relieve.pressure on the
unit. Allow unit to cool for about 2
min. It should run when you turn it
ON again.
3.Low voltage. 3. Contact Generac service facility.
4.Trigger not open. 4. Open trigger.
5.Electrical defect. 5. Contact Generac service facility.
Pressure washer does not 1.Pump is sucking air. 1. Water hose must be 1/2-inch
come up to pressure. or greater in diameter.
Be sure water supply is ON.
Be sure water supply is clean.
Check all connections for leaks
or blockage.
Turn OFF the unit, hold trigger in
OPEN position to relieve pressure
and allow air in line to escape.
With trigger still in OPEN position
turn ON the unit. Repeat if
necessary.
2.Water inlet is clogged. 2. Clean water inlet screen.
3.Pump not bled to remove air. 3. Switch OFF washer, press trigger,
switch ON washer while pressing
trigger. Repeat if necessary.
4.Pump is faulty. 4. Contact Generac service facility.
High pressure spray is irregular. 1.Nozzle or water supply is restricted. 1. Unplug unit and clean nozzle.
2.Water supply is inadequate. 2. Turn ON water to full position.
NOTES
13
GENERAC
Generac 1300PSI Electric High Pressure Washer
EXPLODED VIEW PUMP AND MOTOR
14
GENERAC
Generac 1300PSI Electric High Pressure Washer
Drawing No. B1744
PARTS LIST PUMP AND MOTOR
15
GENERAC
Generac 1300PSI Electric High Pressure Washer
Drawing No. B1744
1 B1514 1 ASSY, Motor Complete
2 97100 1 CAP, HP
3 21054 1 BOOT, Rubber
4 21055 1 GROMMET, Rubber
5 20138 1 SWITCH, Auto
6 20928 1 HOUSING, Auto-Switch
7 20218 1 CAP, Retainer
8 20213 1 PISTON ASSY, Auto Switch
9 21525 1 WIPER, Piston Bore
10 B1124 1 CAP, Inlet
11 97855 1 O RING, dia. 6.5 x 2.01mm
12 97934 3 O RING, Chk Valve dia. 12.4 x
.78mm
13 20212 1 SPRING, 15.08 x dia. 1.62 CS x
22.3
14 B1565 1 SEAT, Ball
15 B1583 1 SCREW, Lock Socket
16 A1495 2 TAPTITE, M4-0.7x10mm SW
MTG
19 21124 1 RING, Backup dia. 4.34 Id x 1.24
20 21123 1 O RING dia. 3.68 Id x 1.78 CS
[.070"]
21 21126 1 RING, Backup dia. 26.0 ID
22 21125 1 O RING dia. 25.07 ID x 2.62 CS
[.103"]
23 20217 1 STOP, Piston Return
24 A1130 1 SPRING, Pop-off Valve
26 97852 1 BALL, dia. 3/16" Pop-off Valve
29 28739A 1 TIE, Wrap
31 97840 3 O RING,
Hi-press dia. 15.6 x
1.78mm
32 97841 3 CAP, Check Valve
33 97837 1 O RING, Hi-press dia. 9.2 x
2.62mm
34 97835 1 O RING, Hsg Seal, dia. 82.2 x
2.62mm
35 B1026 1 CAP, Vinyl
36 76353A 1 PLUG, Taper dia. 5.4
37 97838 3 ASSY., Check Valve, Inlet
38 A1111A 1 PUMP, Head
39 97839 3 ASSY., Check Valve, Outlet
40 97851 3 O RING, Piston dia. 10.82 x
1.78mm
41 97832 3 PISTON dia. 15 x 65mm
42 40946 4 BOLT, SHCS M6- 1.0 x 35mm
43 93873 7 LOCKWASHER, M6 Ribbed
44 93667 3 SEAL, Piston U Cup
45 97831 3 SPACER, Pilot
46 93680 3 SEAL, Oil-piston dia. 15 TC4
47 20140 1 HOUSING, Piston
48 99503 3 SPRING, Piston Return
49 40945 3 RETAINER, Piston Spring
50 97962 3 BOLT, SHCS M6-1.0 x 20mm
51 97824A 1 BEARING, Needle dia. 40 x
60mm
52 97826 1 WASHER, Brg dia. 40 x 60 x
1mm
53 97825 1 WASHER, Brg dia. 36 x 60 x
6mm
54 97716 1 CAM, Axial 4.3 MM Stroke
55 97829C 1 GEAR, Axial Cam
56 97822 1 BEARING, Ndle Thrust dia. 35 x
52mm
57 20610 1 WASHER, Brg dia. 35 x 55 x
3mm
58 97823 1 WASHER, Brg dia. 35 x 52 x
1mm
59 97834 2 BEARING,
Needle dia. 8 x 12 x
10mm
60 97833 1 SHAFT, Idler Axial Cam
Item Part # Qty. Description Item Part # Qty. Description
EXPLODED VIEW XXXXXX...
16
GENERAC
Generac 1300PSI Electric High Pressure Washer
Drawing No. B1744
EXPLODED VIEW MAIN UNIT
PARTS LIST MAIN UNIT
17
GENERAC
Generac 1300PSI Electric High Pressure Washer
Drawing No. B1744
1 N/A 1 ASSY., Motor and Pump (see exp. view B1744 on pages 14 and 15)
2 B1415 1 DECAL, Circuit
3 A1252 1 DECAL, Unit
4 A1313 1 DECAL, Instructions
5 20566 1 DECAL, 1-800 #
6 98806 1 FOAM, Air In, Fan-end
7 97893 1 HOUSING, Switch and Cord
8 20984 1 SWITCH, Rocker 16A
9 98801 4 MOUNT, Rubber
10 97892 1 COVER, Motor
11 20985 1 ENCLOSURE, Rocker Switch Boot
12 20986 1 BOOT, Rocker Switch
13 84543B 2 SCREW, 3.5mm x 12mm Plastite
14 98805 1 CORD, Power
15 84358 4 SCREW, #6-19 x .75 mm Plastite
16 99349 1 STRAIN RELIEF, Cord
17 B1053 1 DECAL, ETL
18 NSP 1 DECAL, Data
19 NSP 1 OVERLAMINATE
20 21334 1 HOUSING, Inlet
21 21335 1 HOUSING, Outlet
22 21265 1 QUICK DISCONNECT, Male
23 96016 1 QUICK DISCONNECT, Female
24 A1484 1 NUT, Strain Relief Lock
25 A1485 1 SEAL RING, Strain Relief
26 97835 1 O RING, Hsg Seal, dia. 82.2 x 2.62mm
27 99350 6 SCREW, #6 Plastite
28 21336 1 GUN, Spray
29 21337 1 WAND, Extension
30 B1417 1 HOSE, High Pressure
31 21338D 1 NOZZLE, Head
32 A1069 1 FOAMER
33 B1051 1 ADAPTER, Accessories
34 87815 1 GOGGLES
35 98904 1 HANG TAG CSA, Nozzle
36 B1236D 1 NOZZLE, 1.15mm dia. (Lilac)
ITEM PART # QTY DESCRIPTION
GENERAC
Generac 1300PSI Electric High Pressure Washer
LIMITED PRESSURE WASHER WARRANTIES (includes Master Contractor)
GENERAC warrants to the original retail purchaser, the pressure washer manufactured by GENERAC to be free from defects in mate-
rial and workmanship for the period(s) set forth below from the date of original purchase. This warranty is not transferable. The term
original purchaser means the person for whom the pressure washer is originally purchased.
Warranty Schedules
Electric Power Washer 1 year (does not apply to commercial or rental operations)
CONSUMER* COMMERCIAL*
Generac GN-Series Engine-driven Engine: 2 years 1 year
Power Washer (2nd year parts only)
Pump: 1 year 90 days
All Other Engine-driven Engine: Warranted solely by Warranted solely by
Power Washers Engine Manufacturer Engine Manufacturer
Pump: 1 year 90 days
* NOTE: For the purpose of this warranty Consumer Use means personal residential household use by original purchaser.
Commercial Use means all other uses, including rental, construction, commercial and income producing purposes. Once a
pressure washer has experienced commercial use, it shall thereafter be considered a commercial use pressure washer for the
purposes of this warranty.
During said warranty period, GENERAC will, at its option, repair or replace any part which, upon examination by GENERAC or GEN-
ERAC Authorized Dealers, is found to be defective under normal use and service**. All transportation costs under warranty, including
return to the factory if necessary, are to be borne by the purchaser and prepaid by the purchaser.
** NORMAL WEAR: As with all mechanical devices, the GN-Series engines need periodic parts service and replacement to
peform well. This warranty will not cover repair when normal use has exhausted the life of a part or an engine.
THIS WARRANTY DOES NOT INCLUDE: Used products and demonstration equipment. Parts such as GUNS, HOSES, WANDS, NOZ-
ZLES or other wear items such as quick couplers, oil, gauges, belts, O-rings, filters, pump packing, etc. Pumps which have been run
without water supplied. Damage or malfunctions resulting from: accidents, abuse, modifications, alterations, or improper servicing. Freez-
ing or chemical deterioration. Normal maintenance such as adjustments, fuel system cleaning and obstruction (due to chemical, dirt,
carbon or lime, etc.).
THIS WARRANTY IS IN PLACE OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, SPECIFICALLY, GENERAC MAKES NO
OTHER WARRANTIES AS TO MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. The duration of any implied war-
ranties which cannot be disclaimed is limited to the time period as specified in the express warranty. LIABILITY FOR CONSEQUENTIAL,
INCIDENTAL, OR SPECIAL DAMAGES UNDER ANY AND ALL WARRANTIES IS EXCLUDED, EVEN IF SUCH DAMAGES ARE A
DIRECT RESULT OF GENERACs NEGLIGENCE. Some states do not allow limitations on how long an implied warranty lasts, or the
exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to you. This war-
ranty gives you specific legal rights and you may also have other rights, which vary from state to state.
For service, see your nearest GENERAC authorized warranty service facility or call 1-800-333-1322. Warranty service can be performed
only by a GENERAC authorized service facility. This warranty will not apply to service at any other facility. At the time of requesting war-
ranty service, evidence of original purchase date must be presented.
GENERAC CORPORATION
/
