Label Picture Description QTY
Assembly Instructions
Caution: You must read this before you proceed
Table
Caution: This Table is NOT a TOY
Keep your child/ children at bay during the assembly process.
Whenever moving/lifting the Table and to prevent damage to the Table, two
adults are needed to execute these actions.
Parts List
A
Table Top
1
B Leg 4
Label Picture Description QTY
①
Bolt
(M8x50mm)
9
②
Washer
9
③
Allen Key
1
Hardware
Assembly Preparation
Noble House Home Furnishings LLC
Before Beginning Assembly:
Assembly Steps
Noble House Home Furnishings LLC
This Table has multiple parts and may require up to 30 minutes to assemble. To give you
an overview of the Table parts, the above picture is to help you put the various parts into
perspective. Please read through the instructions below to familiarise yourself with the
parts and steps before assembly.
Step 1
Unpack and place all parts on a clean, non-marring surface.
Leg (B)
Table Top (A)
Noble House Home Furnishings LLC
Attach Leg(B) to the Table Top(A) using Bolts(①), and Washers(③) with Allen Key(④).
Do not fully tighten the Bolts.
Repeat the same process with the remaining three Legs(B).
Step 2
B
A
3
1
2
Noble House Home Furnishings LLC
Stand the Table up, with assistance from your adult partner.
Exert pressure floorwards, onto the Table with both your hands.
This pressure will help the Legs and Table Top reach full alignment status.
Check for wobbles on a LEVEL surface.
If no wobbles are found proceed to tighten the Bolts in a sequential manner, until evenly
secured.
When tightening the Bolts tighten sequentially.
Do not tighten any Bolt fully and then move on towards the next one.
If there are still wobbles, loosen the Bolts and excute the same above process.
If the Table is not Stable it could lead to damage to the product.
Your Table is ready for use.
This Table can only be used on a flat, level surface.
Step 3
A
Noble House Home Furnishings LLC
Noble House Home Furnishings LLC
Noble House Home Furnishings LLC
Noble House Home Furnishings LLC
Noble House Home Furnishings LLC
Noble House Home Furnishings LLC
Noble House Home Furnishings LLC
Noble House Home Furnishings LLC
Noble House Home Furnishings LLC
Assembly Instructions
CHAIR
Caution: You must read this before you proceed
CAUTION : This Chair is NOT a TOY.
Keep your child / children at bay during the assembly process.
For turning the Chair and to prevent damage to the Chair, 02 persons may be needed
to execute this action.
Assembly Instructions
Noble House Home Furnishings LLC
1/7
No. Picture Description QTY
A Backrest Panel 1
B Right Leg Panel 1
C Left Leg Panel 1
D Seat Panel 1
E Seat Cushion 1
No. Picture Description QTY
① Allen Key 1
② Screw (M6*60mm) 7
Parts List
Hardware
Noble House Home Furnishings LLC
1/7
2/7
Assembly Preparation
This Chair has multiple parts and may require up to 30 minutes to assemble. To give you an
overview of the Chair parts, the above picture is to help you put the various parts into perspective.
Please read through the instructions below to familiarise yourself with the parts and steps before
assembly.
Before Beginning Assembly:
Assembly Steps
Overview
Front Facing
Right Leg Panel (B)
Left Leg Panel (C)
Backrest Panel (A)
Seat Cushion (E)
Seat Panel (D)
Noble House Home Furnishings LLC
1/7
3/7
Unpack and place all parts on a clean, non-marring surface.
2.1) Align Backrest Panel (A) and Seat Panel (D) onto Left Leg Panel (C) as shown above.
2.2) Align Right Leg Panel (B) onto Backrest Panel (A) and Seat Panel (D) as pictured.
Noble House Home Furnishings LLC
4/7
Carefully turn the Chair over.
Attach Left Leg Panel (C) to Seat Panel (D) and Backrest Panel (A) by using 3 Screws (②) with
Allen Key (①).
Do not fully tighten the Screws.
Attach Right Leg Panel (B) to Seat Panel (D) and Backrest Panel (A) by using 3 Screws (②) with
Allen Key (①).
Do not fully tighten the Screws.
Noble House Home Furnishings LLC
5/7
Place Seat Cushion (E) onto the Chair.
Lay the Chair down and tie the velcro straps of the Cushion (E) to the Seat Panel (D) as shown
above.
Your Chair is ready for use.
This Chair can only be used on a flat, level surface.
Step 6
Step 5
Place the Chair onto a level surface, then carefully sit onto the Chair.
This pressure will help the Chair reach full alignment at all joints.
In a sequential manner, gradually tighten all Screws until evenly secured.
Inspect the Chair and make sure all parts are adequately connected.
Noble House Home Furnishings LLC
6/7
Page is loading ...
/
