Riva RTS650 Installation guide

Brand
Riva
Model
RTS650
Category
Security cameras
Type
Installation guide
www.rivatech.de
Specification subject to change without notice
RTS650 Thermal Camera
Installation Guide
Torx Wrench
Screw &
Plastic Anchor-3pcs
Quick Installation Guide
Installation Template
Adaptor & AC Plug
WALL CUSHION
RTS Series RTS650 Installation Guide
04-2017-A www.rivatech.de 2
Precaution
Please read this manual carefully before installing the unit.
Never disassemble the camera. Unauthorized disassembly may cause equipment
failure or damage to the unit.
Please do not install the camera in a place exposed to direct sunlight.
Do not operate the camera in environments beyond the specified temperature.
Refer to Environment Condition on APPENDIX (A): SPECIFICATIONS in this manual.
Before applying power to the camera, check the power source to ensure that it is
within the specifications. Refer to Electrical Characteristics on APPENDIX (A):
SPECIFICATIONS.
RTS Series RTS650 Installation Guide
04-2017-A www.rivatech.de 3
Table of Contents
Precaution ................................................................................................................ 2
1. FEATURES ............................................................................................................. 4
2. PACKAGE CONTENTS............................................................................................. 5
3. PART NAMES ........................................................................................................ 6
4. CAMERA INSTALLATION ........................................................................................ 7
4.1. Installing the camera ............................................................................................. 7
4.1.1. Installation without bracket ........................................................................................ 7
4.1.2. Compatible Accessories .............................................................................................. 9
4.2. Adjusting angle of the camera ............................................................................. 10
4.3. Camera Image Settings ........................................................................................ 10
5. CONNECTIONS .................................................................................................... 11
6. CONFIGURATION ................................................................................................ 14
6.1. Set up network environment ............................................................................... 14
6.1.1. Generic IP Environment ............................................................................................ 14
6.1.2. Custom IP Environment............................................................................................. 15
6.2. View video on web page ...................................................................................... 16
6.2.1. ActiveX Installation .................................................................................................... 16
6.2.2. View video using IPAdmin Tool ................................................................................. 17
6.3. Reboot .................................................................................................................. 18
6.4. Factory Default ..................................................................................................... 18
6.5. Safe Mode ............................................................................................................ 19
APPENDIX (A): SPECIFICATIONS .............................................................................. 20
Summary ..................................................................................................................... 20
Electrical Characteristics ............................................................................................. 21
Environment Condition ............................................................................................... 21
Mechanical Condition ................................................................................................. 21
APPENDIX (B): POWER OVER ETHERNET ................................................................. 22
Power Comparison ...................................................................................................... 22
APPENDIX (C): DIMENSIONS ................................................................................... 23
APPENDIX (D): HEXADECIMAL-DECIMAL CONVERSION TABLE ................................. 24
REVISION HISTORY ................................................................................................. 25
RTS Series RTS650 Installation Guide
04-2017-A www.rivatech.de 4
1. FEATURES
Camera
17 ㎛ vanadium oxide mirobolometer technology
206x156 array size / Various resolutions by scale-up
20°, 36° field of view
Streaming
Dual streaming mode (such as different codec/resolution/bit rate and so on.)
Burnt-in text supported
Unicast/Multicast supported
Video
H.264 and MJPEG(Motion JPEG)
Max 9 fps in all resolutions
Text Overlay
Video Motion Detection supported
Audio
Two-way audio streaming
Audio compression: G.711 µLaw
Sensor/Alarm
1 Digital Input / 2 Digital Outputs
Network
RTSP/ HTTP protocol supported
10/100 Base-T Ethernet
Additional Features
microSDHC card embedded
PoE supported
Built-in Video Content Analysis
SDK (Software Development Kit) provided
VCA (Video Content Analysis)
VCA Detect (Included as basic)
RTS Series RTS650 Installation Guide
04-2017-A www.rivatech.de 5
2. PACKAGE CONTENTS
Please unpack the package carefully and handle the equipment with care. The package
contains:
Note
i
The contents above are subject to change without prior notice.
Camera
DC Power Adaptor & Universal Plugs
Screws (M4x30) & Plastic Anchors
Wall Cushion
Torx Wrench (T20 M4x23)
Quick Start Guide
Ferrite Core
Installation Template
ZCAT1518-0730
ZCAT2132-1130
Torx Wrench
Screw &
Plastic Anchor-3pcs
Quick Installation Guide
Installation Template
Adaptor & AC Plug
WALL CUSHION
CABEL CORE
Torx Wrench
Screw &
Plastic Anchor-3pcs
Quick Installation Guide
Installation Template
Adaptor & AC Plug
WALL CUSHION
CABEL CORE
Torx Wrench
Screw &
Plastic Anchor-3pcs
Quick Installation Guide
Installation Template
Adaptor & AC Plug
WALL CUSHION
CABEL CORE
Torx Wrench
Screw &
Plastic Anchor-3pcs
Quick Installation Guide
Installation Template
Adaptor & AC Plug
WALL CUSHION
Torx Wrench
Screw &
Plastic Anchor-3pcs
Quick Installation Guide
Installation Template
Adaptor & AC Plug
WALL CUSHION
CABEL CORE
RTS Series RTS650 Installation Guide
04-2017-A www.rivatech.de 6
3. PART NAMES
① Sunshield
It prevents direct sunlight.
② Audio|Sensor|Alarm connection cables
Cables to connect audio input(microphone), audio output(speaker), digital input(sensor),
and digital output(alarm). Refer to 5. CONNECTIONS for more information.
③ LAN connector
RJ45 LAN connector for 10/100 Base-T Ethernet (PoE supported).
④ Power adaptor connector
Connect the provided DC12V adaptor for power supply.
Torx Wrench
Screw &
Plastic Anchor-3pcs
Quick Installation Guide
Installation Template
Adaptor & AC Plug
WALL CUSHION
CABEL CORE
BLACK
BROWN
RED
ORANGE
YELLOW
GREEN
BLUE
VILOET
GRAY
AUD IN
AUD GND
AUD OUT
DI
DI COM
DO1(N.O)
DO1 COM
DO2(N.C)
DO2 COM
Audio|Sensor|Alarm
connection cables
LAN connector
Sunshield
Power adaptor connector
* The model herein and its appearance are subject to change without any prior notice.
RTS Series RTS650 Installation Guide
04-2017-A www.rivatech.de 7
4. CAMERA INSTALLATION
4.1. Installing the camera
4.1.1. Installation without bracket
Installation Template
(Unit: mm)
Caution
!
Installation template’s image size scale in this installation guide is not 1:1.
The correct-size template paper can be found inside the package separately.
Torx Wrench
Screw &
Plastic Anchor-3pcs
Quick Installation Guide
Installation Template
Adaptor & AC Plug
WALL CUSHION
CABEL CORE
RTS Series RTS650 Installation Guide
04-2017-A www.rivatech.de 8
Installation
Note
i
< Use of Ferrite Core >
Installing the ferrite core to a LAN cable is highly recommended to reduce high
frequency noise level. Please follow the instructions below.
1. Open the ferrite core by lifting the clip.
2. Make one loop with the cable through the ferrite core.
3. Close the ferrite core to hold the cable loop into its
place.
Caution
!
Sealing gaps is recommended as gaps may appear after the camera installation.
Gaps may cause problems such as moisture, water leakage and etc., which
negatively affect the operation of the camera if gaps remain unsealed.
Caution
!
To prevent products from damage, place the camera on a stable and non-
vibrating surface. If the stability is in doubt, consult safety personnel for
reinforcements, and then proceed with the installation.
Torx Wrench
Screw &
Plastic Anchor-3pcs
Quick Installation Guide
Installation Template
Adaptor & AC Plug
WALL CUSHION
CABEL CORE
1) Drill three holes on the installation surface based on the provided installation template.
2) Insert the plastic anchors into the holes.
3) Install the provided ferrite core on the cable by referring to the Note below.
4) Attach the provided wall cushion to the bottom of the camera’s pan/tilt bracket.
5) Fix the camera to the installation surface.
A. Align the screw holes of the camera’s pan/tilt bracket and the plastic anchors.
B. Insert the provided screws(M4X35) into the plastic anchors through the screw holes of
the camera’s pan/tilt bracket.
C. Tighten the screws firmly into the plastic anchors.
6) Connect all the necessary cables by referring to 5.CONNECTIONS for more information.
7) Adjust the angle by referring to 4.2. Adjust angle of the camera.
DO DI
1 1C C
+
DC12V
ETHERNET
RESET
MICRO
SD
DO DI
1 1C C
+
DC12V
ETHERNET
RESET
MICRO
SD
ETHERNET
WIRE
RTS Series RTS650 Installation Guide
04-2017-A www.rivatech.de 9
4.1.2. Compatible Accessories
The compatible accessories to mount this camera model are as follows.
Model Names & Combinations
PMA-U100
CMA-U100
JBK-U100
Refer to the corresponding accessory model’s installation guide for the instructions.
Model Image
PMA-U100
CMA-U100
JBK-U100
PMA-U100/CMA-U100
This guide illustrates how to assemble the corner mount adapter and
pole mount adapter.
Check the letter of the alphabet assigned to each adapter and tighten
the screws in the corresponding holes to assemble the adapter.
A-A-A(M4 PAM)
IPN6802HD
B-B-B(M4 PAM)
IPN6702HD
C-C-C-C(M5 PAM)
IPN6602HD
D-D-D(M6 PAM)
ODE-1000T
E-E-E-E(M6 PAM)
WMB-3000P & CMB-3000P
F-F-F-F(M5 PAM)
JBK-U100
PMA-U100/CMA-U100
This guide illustrates how to assemble the corner mount adapter and
pole mount adapter.
Check the letter of the alphabet assigned to each adapter and tighten
the screws in the corresponding holes to assemble the adapter.
A-A-A(M4 PAM)
IPN6802HD
B-B-B(M4 PAM)
IPN6702HD
C-C-C-C(M5 PAM)
IPN6602HD
D-D-D(M6 PAM)
ODE-1000T
E-E-E-E(M6 PAM)
WMB-3000P & CMB-3000P
F-F-F-F(M5 PAM)
JBK-U100
G-G-G-G(M6 PAM)
WMB-3000 & WMB-3000S
A-A-A : IPN6802HD
B-B-B : IPN6702HD
C-C-C-C : IPN6602HD
D-D-D-D : WMB-3000P & CMB-3000P
1
HOUSING COVER에 WALL MOUNT CABLE을 통과시킨다.
2
3
1
2
3
1
2
1
2
1
2
3
4
5
1
2
3
4
5
1
2
HOUSING COVER와 WALL MOUNT BRACKET을 조립한다
결합 후 상태 이미지
3mm Hex Wrench를 사용하여 볼트를 푼다. (4EA 동일 방법)
Hinge를 젖힌 후 빼낸다. (2EA 동일 방법)
B
BULLET CAMERA의 CABLE을 HOUSING COVER에 통과시킨다.
장착하는 CAMERA에 맞는 BOLT를 사용하여
CABLE을 GASKET에 끼운 후 위치에 맞게 삽입한다.
CABLE을 GASKET에 맞춰 정리한 후 GASKET을 접어 닫는다.
M3x12 BOLT를 사용하여 PLATE를 조립한다.
왼쪽 상세 이미지를 참고 하여 CABLE GLAND 를 조립한다.
CABLE GLAND를 HOUSING COVER에 완전히 조립한다.
HOUSING COVER의 LOWER와 UPPER를
HOUSING COVER의 UPPER와 LOWER를
BB
A A
A
C C
CC
D D
DD
PMA-U100 CMA-U100 WMA-U100
M5x12 BOLT를 사용하여 HOUSING COVER와 PMA-U100을 체결한다.
결합 후 상태 이미지
M5x12 BOLT를 사용하여 HOUSING COVER와 CMA-U100을 체결한다. M5x12 BOLT를 사용하여 HOUSING COVER와 WMA-U100을 체결한다.
결합 후 상태 이미지 결합 후 상태 이미지
이미지와 같이 위치 시킨 후 HINGE를 사용하여 체결한다.
이미지와 같이 위치 시킨 후 HINGE를 사용하여 체결한다.
3mm Hex Wrench를 사용하여 볼트를 조인다. (4EA 동일 방법)
3mm Hex Wrench를 사용하여 볼트를 조인다. (4EA 동일 방법)
E E
E
E-E-E : ODE-1000T
1
2
HOUSING COVER에 조립한다.
RTS Series RTS650 Installation Guide
04-2017-A www.rivatech.de 10
4.2. Adjusting angle of the camera
4.3. Camera Image Settings
On the camera’s webpage, users can configure the aspect ratio and the image orientation via
the path, Setup > Video & Audio > Camera.
For more detailed information, refer to Web Page User's Manual.
Torx Wrench
Screw &
Plastic Anchor-3pcs
Quick Installation Guide
Installation Template
Adaptor & AC Plug
WALL CUSHION
CABEL CORE
1) Loosen the set screw located on the right side of the camera’s bracket by using the
provided Torx(T20 M4x23) wrench. Once the set screw is loosened, you can move the
tilting joint and the panning joint of the camera respectively.
2) Adjust the angle by moving the tilting joint and the panning joint.
3) Tighten the set screw with the Torx wrench to fix the angle.
RTS Series RTS650 Installation Guide
04-2017-A www.rivatech.de 11
5. CONNECTIONS
① Audio connection
The camera provides a mono audio input and output. Due to low audio output power, an
amplified speaker is recommended for enhanced sound (Refrain from connecting a
headphone or an earphone directly to the camera).
- Microphone In: Max 2Vp-p, 20KΩ (90dB)
- Headphone Out: 60mW, 16Ω (95dB)
② Sensor (DI) connection
Sensor (DI) can be connected to either a voltage type sensor or a relay type sensor as the
following figures. Settings can be done through the camera’s webpage.
Input voltage range: 0VDC minimum to 5VDC maximum, Max 50mA
Caution
!
Do not exceed the maximum input voltage or relay rate.
Mic
Amp Speaker
ETHERNET
MICRO SD
DC12V
DO
DI
1
OutOut
1
VIDEO
C C
In
AUDIO
+
Reset
SW1 SW2 SW3
SW5 SW6
N / A N / A
N / A N / A
SW1
SW2
SW3
SW4
SW5
SW6
Torx Wrench
Screw &
Plastic Anchor-3pcs
Quick Installation Guide
Installation Template
Adaptor & AC Plug
WALL CUSHION
CABEL CORE
BLACK
BROWN
RED
AUD IN
AUD GND
AUD OUT
ORANGE
YELLOW
DI
DI COM
GREEN
BLUE
VILOET
GRAY
DO1(N.O)
DO1 COM
DO2(N.C)
DO2 COM
LAN connector
Power adaptor
connector
AUDIO
SENSOR
ALARM 1
ALARM 2
RTS Series RTS650 Installation Guide
04-2017-A www.rivatech.de 12
③ Alarm (DO1 | DO2) connection
Only the relay type is supported.
- Digital Output 1
Relay Rating: Max 30VDC 1A
Normally Open (N.O) at power off
- Digital Output 2
Relay Rating: Max 30VDC 1A
Normally Closed (N.C) at power off
Caution
!
Do not exceed the maximum relay rating.
+3.3V
DI
COM
DI
COM
+
-
Relay Type
Voltage Type
+
-
Output of
Sensor
Output of
Sensor
Internal
Internal
+
-
RTS Series RTS650 Installation Guide
04-2017-A www.rivatech.de 13
④ LAN connection
This is a RJ45 LAN connector for 10/100 Base-T Ethernet. Use the Ethernet cable (RJ45) to
connect the device to a hub or a router in the network. Refer to “Appendix (B). Power over
Ethernet” for more information.
⑤ Power Connection
The camera can be powered by either 12VDC or PoE. If the camera is powered via PoE, you do
not need to connect the power adaptor. For more information about PoE, refer to “Appendix
(B). Power over Ethernet” for more information.
Note
i
[ Operation of the internal heater ]
- Temperature criterion for the heater operation: 0˚C (32˚F)
-
Lowest temperature to
guarantee the heater operation during the device
operation: -40˚C (-40˚F)
-
Lowest temperature to boot up the device when the device is powered on:
- 0˚C (32˚F)
RTS Series RTS650 Installation Guide
04-2017-A www.rivatech.de 14
6. CONFIGURATION
6.1. Set up network environment
The default IP address of the device is 192.168.XXX.XXX. Users can identify the IP address of the
device from converting the MAC address’s hexadecimal numbers, which is attached to the
device. Be sure that the device and PC are on a same network before running the installation.
IP address : 192.168.xxx.xxx
Subnet mask: 255.255.0.0
6.1.1. Generic IP Environment
In case of generic private network environment where IP address 192.168.XXX.XXX are used,
users may view the live streaming images on a web page using the device’s default IP address:
1. Convert the device’s MAC address to the IP address. Refer to the Hexadecimal-Decimal
Conversion Chart at the end of the manual.
(The MAC address of the device is attached on the side or bottom of the device.)
2. Start the Microsoft® Internet Explorer web browser and enter the address of the device.
3. Web streaming and device configurations are supported through ActiveX program. When the
ActiveX installation window appears, authorize and install the ActiveX.
MAC address = 00-13-23-01-14-B1 → IP address = 192.168.20.177
Convert the last two sets of hexadecimal numbers to decimal numbers.
RTS Series RTS650 Installation Guide
04-2017-A www.rivatech.de 15
6.1.2. Custom IP Environment
Please access our website and download necessary IPAdminTool first:
http://www.rivatech.de/en/downloads/software
IPAdminTool is a management tool, which automatically scans all of the network products for
users to perform administrative tasks, which includes network configurations, firmware
update, device reboot, and device organizations.
To modify the device’s default IP address for customized network area;
1. Find the device from the IPAdminTool’s list and highlight the device’s name.
2. Right-click the mouse and select IP Address; IP Setup window appears.
* There are two options that are for a single device or for multiple devices respectively. For one device, click “Single”.
3. On the New Information table in the Single IP Change window, modify the last two digits of
the device’s IP address. Make sure to input the correct ID and PW of the device (default:
root / pass).
4. Click Apply to complete the modification.
Give a new unique IP address by
modifying the last two digits.
RTS Series RTS650 Installation Guide
04-2017-A www.rivatech.de 16
6.2. View video on web page
Type the proper IP address to view the live streaming images through a web browser.
The default username and password is root / pass.
6.2.1. ActiveX Installation
1. When the browser asks to install the AxUMF software, click Install to proceed.
2. When Setup installation pop-up window appears, click Install to proceed with rest of
installations.
Note
i
Depending on system OS and Internet Explorer version, installation experience
may differ from one another. Figures described above are from Windows 7,
Internet Explorer 9 environment.
RTS Series RTS650 Installation Guide
04-2017-A www.rivatech.de 17
6.2.2. View video using IPAdmin Tool
IPAdminTool automatically searches all activated network encoders and IP cameras and shows
the product name, IP address, MAC address and etc.
1. From the IPAdminTool’s product list, select the device by highlighting it.
2. Right-click the mouse, and select Web view.
Then, the system’s default web browser opens the device’s address.
Caution
!
Whether directly accessing the streaming video by typing IP address on a web
page or taking steps through IPAdminTool, the ActiveX is needed to be installed
for the Microsoft® Internet Explorer to have the complete configuration
privileges.
RTS Series RTS650 Installation Guide
04-2017-A www.rivatech.de 18
6.3. Reboot
On the Device
Perform the following procedure to reset your device.
1. Press the reset button for 2 seconds when the device is powered on.
2. Wait for the system to reboot.
Caution
!
Do not press the reset button for more than 2 seconds. Otherwise, the camera
may be switched to its factory default settings.
On the Webpage
Reboot the device via the camera’s webpage:
1. Go to Setup > Maintenance > Reboot.
2. Click the Reboot button to reboot the device.
3. Wait for the device to complete booting.
6.4. Factory Default
Resetting the device back to the factory default will initialize all parameters including the IP
address back to the factory defaults.
On the Device
1. Press the reset button for 10 seconds by making sure that booting is complete on the
device.
2. Wait for the system to reboot.
Then, all the parameters of the device will be initialized.
On the webpage
1. Go to Setup > Maintenance > Reset All Settings.
2. Select the items that you want to preserve from the initialization among network
settings, user account information, and time zone setting.
3. Click Reset All Settings.
Note
i
The factory default settings can be inferred with the following information:
IP address: 192.168.xx.yy
Network mask: 255.255.0.0
Gateway: 192.168.0.1
User ID: root
Password: pass
RTS Series RTS650 Installation Guide
04-2017-A www.rivatech.de 19
6.5. Safe Mode
What is Safe Mode?
There may be certain occasions that your camera repeatedly fails to boot. Then, your camera
may enter safe mode to be recovered from the occasions.
What may have caused Safe Mode?
Here below are the main typical causes.
* The power supply is continually unplugged certain times in the middle of system booting.
* The firmware files required for system booting are damaged.
* There are conflicts in the system settings.
How to recover your system from Safe Mode
The messages above will appear on the webpage when your device has been rebooted in safe
mode. Then, you should follow the instructions on the webpage according to each step.
Note
i
There is another method to update firmware, which is using IPAdminTool.
Please refer to ‘IPAdminTool User’s Manual.pdf’ for the detailed procedure.
Note
i
If your device is still in safe mode after trying to update firmware, please contact
your local agency to get further assistance.
Browse
RTS Series RTS650 Installation Guide
04-2017-A www.rivatech.de 20
APPENDIX (A): SPECIFICATIONS
Summary
Camera Module
Array Size
206x156
Detection Type
Uncooled vanadium oxide microbolometer
Sensor pixel size
12um
Spectral Response
7.8 ~ 14um
Lens
RTS650-A20
6.8mm, F1.2(FOV:20°)
RTS650-A36
4.0mm, F1.2 (FOV:36
o
)
Sensitivity
Less than 100mK
Video
Compression Format
H.264 and MJPEG Selectable per Stream
Number of Streams
Dual Stream, Configurable
Resolution
4:3 Mode
QVGA(320x240)
VGA(640x480)
NTSC(720x480)
PAL(720x576)
SVGA(800x600)
16:9 Mode
320x180
480x270
640x360
800x450
960x540
1120x630
1280x720
Frame Rate
Max. 9FPS in all resolutions
Motion Detection
Built-in
Burnt-in Text (Digital)
Time stamp and text caption overlay
Analogue Output
-
Audio
Input/output
1/1 channel
Compression Format
G.711
Function
Digital Input/output
1/2 channel
RS-485
-
Network
10/100 Base-T
Power over Ethernet (PoE)
Supported
Protocol
QoS Layer 3 DiffServ, TCP/IP, UDP/IP, HTTP, HTTPS, RTSP,
RTCP, RTP/UDP, RTP/TCP, mDNS, UPnP™, SMTP, DHCP, DNS,
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25

Riva RTS650 Installation guide

Brand
Riva
Model
RTS650
Category
Security cameras
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents