Zavio D4220 Quick start guide

0

86085A5000030

/ B5210

ZAVIO Outdoor IR Mini Dome

Quick Installation Guide

1

Quick Installation Guide

Please follow the installation steps below to set up your IP Camera.

Check the package contents with the list below. See P.1

Physical overview. See P.2

I/O Terminal Block Circuit. See P.3

I/O Terminal Block Pin Definition. See P.3

LED Indicator Definition. See P.3

Power mode. See P.4

Installation of hardware and connection of all cables. See P.4

Windows: Go to Zavio website and download Camera Installation Tool. See P.7

Access the IP Camera using Camera Installation Tool. See P.8

MAC OS: using Safari Browser. See P.11

Lighting environment. See P.13

Change language of the web interface. See P.13

Application of IP Camera. See P.14

Package Contents

Camera

IP Camera

Quick Installation Guide

Brief product information and quick installation

Accessory

Alignment Sticker, screw pack for wall and

ceiling mounting, desiccant.

Software

The following software and information are available online:

- Video Management Software

- Camera Installation Tool

- User manuals

- Camera Language Packs

You may download the above at http://www.zavio.com/downloads.php or you

may scan the below QR-Code.

To activate Video Management Software, please enter the license key below.

2

Physical overview

Built-in Microphone

Dome bubble

Top cover

Lens

MicroSD/SDHC/SDXC

Reset

Power LED Indicator

Network LED Indicator

External I/O connector

Internal microphone

Light Sensor

IR LEDs

3

I/O Terminal Block Circuit

Note: Please use the supplied waterproof RJ45 connector and seal all connectors tightly to avoid moisture.

I/O Terminal Block Pin Definition

Pin Color

Definition

Description

Max. V/A

R

Red

+ 12VDC

12V DC

1.2W

B

Black

Digital

Output 1

Uses an NPN transistor with the emitter connected to the

GND pin. If used with an external relay, a diode must be

connected in parallel with the load for protection against

voltage transients.

100 mA

24V

Y+B

Yellow+Black

Audio

Line In

Connect the wires of the audio input device to GND (Pin 4)

and AUDIO.IN (Pin 1).

-

W+B

White+Black

Audio

Line Out

Connect the wires of the audio output device to GND (Pin 4)

and AUDIO.OUT (Pin 2).

-

G+B

Grey+Black

Digital

Input 1

Connected to GND to activate, or leave floating

(or unconnected) to deactivate.

30V DC

Brown+B

Brown+Black

Ground

-

LED Indicator

LED

Color

Indication

Network

Blue

Solid blue when network is established.

Blink blue when there is network activity.

4

Power

Red

Solid red for booting up process

Blue

Solid blue for booting up completion

Purple

Blink purple during: (a) firmware upgrade, (b) reset

button pressed for at least 5 sec to factory default.

Unlit

When reset button is pressed or when power off.

Power Mode

PoE Mode

Power Requirement

PoE (IEEE802.3af) with Class 3

Power Consumption

4.95 W

Adaptor Mode

Power Requirement

12V/1A Adaptor

Power Consumption

5.0 W

Install the hardware and connect all cables

A. RJ45 waterproof connector

1) Make sure all components are assembled as shown on the below graph.

2) Check that the ethernet port and the waterproof main body are tightly fasten.

3) Please use the supplied waterproof RJ45 connector and seal all connectors

tightly to avoid moisture.

B. Wall and ceiling mounting

1) Attach the alignment sticker to the wall/ceiling. Drill two holes into the wall -

two for screws and one for cable.

2) Align the screw holes on the metal base to the two plastic anchors on the

wall/ceiling, insert the supplied screws to the hole and secure them.

5

6

C. Connect all cables

E1. Without Power over Ethernet (PoE) connection

1. Connect the power adaptor to the IP Camera.

2. Use a standard RJ-45 network cable and connect the IP Camera to a

hub/switch/router.

E2. Power over Ethernet (PoE)

1. Use a standard RJ-45 network cable and connect the IP Camera to a

PoE-enabled hub/switch/router.

D. To adjust the view angle- 3 axis mechanism design

1) Turn the lens module right and left to your desired pan position.

2) Turn the lens module up and down to your desired tilt position.

3) Turn the lens module to adjust the image orientation to satisfied angle.

7

Important:

Make sure the IR LEDs are not blocked by the housing as it will affect the IR performance.

If the image is upside down, please use the image rotate function in Video Setting.

E. Completion

Fix the tamper-proof screws using supplied special hex. Be careful do not scratch

the cover glass. Clean the dome bubble to remove the dust and finger print.

Windows: Go to Zavio Website and download Camera Installation Tool

Please go http://www.zavio.com/softwaredownloads.php download “Camera

Installation Tool”. And follow the installation process to complete the

installation.

8

Access the IP Camera using Camera Installation Tool

1. Please check two settings before using Camera Installation Tool.

a. Browser’s Internet Properties → Security→ Default Level

b. Browser’s Internet Properties → Privacy → Uncheck Pop-up Blocker

9

2. Click the Camera Installation Tool Icon on your desktop. The main page will

show up listing all active camera and video server devices. Select the

desired IP cameras from the list and click Link to IE.

3. Enter Username and Password to login to the IP Camera.

(Default is admin / admin)

10

4. When accessing the IP Camera for the first time, a yellow information bar

appears below the address bar: This website wants to install the

following add-on: AxvideoView.cab from ‘Zavio Inc’.

5. Click the information bar, and select Install ActiveX control.

6. Click Install

11

7. Live video will display in the center of your web browser.

MAC OS using Safari Browser

1. Select Safari Icon

2. Click Bonjour function and select the camera you wish to access.

12

3. Enter name and password to login to the IP camera

(Default is admin / admin)

4. Live video will display in the center of your web browser.

3. Enter name and password to login to the IP

camera. (Default is admin / admin)

13

Lighting environment setting

Default setting for lighting environment is Auto. You may change exposure

frequency to 50 or 60 Hz at Setting > Live View > Camera Setting > Image

Setting.

Change the Web Interface into your preferred language

Before accessing the Setting page to change the language of the web interface,

you must download the language pack.

1. Go to http://www.zavio.com/downloads.php and download the language pack

corresponding to your IP camera model.

2. Go to the IP camera setting page and upload the preferred language from the

language pack downloaded from step 1.

Setting > System > Maintenance > Language > Upload

3. Once the upload is complete, the browser will automatically change the

language.

14

Application of IP Camera

15

Memo

…………………………………………………………………………………………………………………………………………………..

11. The IP Camera automatically accepts your

invitation and its live video is displayed.

Snapshot

3

Zavio D4220 Quick start guide

Zavio D4220 Quick start guide

Related papers

Other documents